Search Documents

By Henry S. McDevitt

External Shock Mitigation (ESM) is being studied as a possible means of retrofitting existing buried structures to provide additional protection from ground shock. As part of this study, two tests were conducted on four ESM models and a control structure. The test articles were placed at a carrnon distance and subjected to the ground motions created by a buried explosive charge consisting of 2,ODO pounds of nitranethane (NM). Adequate instrumentation data were obtained to assess the response of the four ESM models. The assessment relied heavily on direct comparison of horizontal motions measured in the models, with similar measurements in the control structure. From the tests, it was observed that peak accelerations were reduced by a factor of 5 by the ESM. However, the particle velocities and displacements were not significantly affected by theEIS.

Jan 1, 1997

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999

In the past decade several significant intrusion-related gold deposits have been discovered in terranes historically exploited for tin-tungsten mineralization (eg Tintina Gold Province, Yukon and Alaska, Tasman Fold Belt, Australia and the Altaid orogenic collage in central Eurasia). This paper presents new data on the geological and geochemical characteristics of these deposits that links them to magmatic-hydrothermal processes and highlights their implications for exploration. New data from several intrusion-related gold provinces suggest that these deposits are found in areas that contain granodiorite to granite, but with a locally significant mafic component, have Rb/Sr ratios ranging between 0.1 and 1.0, and are moderately reduced (Fe2O3/FeO ~ 0.1 to 0.6) ilmenite series, metaluminous, I-types. The intrusions are distinct from porphyry copper intrusions and tin granites, but are more akin to tungsten granites. Hydrothermal fluid types vary with depth of emplacement in intrusion-related gold deposits and new proton induced X-ray emission (PIXE) data from syn-ore fluid inclusions in shallow and deep deposits provide fascinating insight into the variation in metal content between the different settings consistent with observed deposit metal associations. Exploration for intrusion-related gold deposits in tintungsten terranes should focus on regions that contain both mafic and felsic intrusion that are moderately reduced, metaluminous, I-type granites rather than terranes with dominantly highly fractionated, strongly reduced, peraluminous S-types. Intrusion-related gold systems occur in variety of deposit styles (in part controlled by host rock, proximity to granite, and depth of emplacement) and exploration geologists need to be aware of the variety of target types in and around the intrusive environment, and be able to recognise whether they are exploring a shallow or deep intrusion-related gold setting.

Jan 1, 2005

By G. Couture

"The Glencore Raglan mine Concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. The nickel metallurgical plant was originally designed to process 100 tonnes per hour of ore to produce 130 000 tonnes of nickel concentrate per year at 16% Ni. The increased grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate at 19% Ni. In 2014, the Metallurgical group, with support from BBA, implemented an expert control system on the flotation circuit. This project was initiated to cope with the high variability of the concentrator’s feed. Increasing the plant recovery and final concentrate grade were also important project objectives. The implementation of the expert system ensures better control of concentrate inventory while maintaining maximum plant throughput. This paper describes the successful implementation of the new control system, the control technology selection and the flotation circuit optimization. It will also discuss the performances obtained with this new approach and the improved process stability.IntroductionThe Raglan Mine is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to produce 130 000 tonnes of concentrate annually at 16% Ni. The increasing of the grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate between 18 and 20% Ni."

Jan 1, 2015

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

Building the Unified Comminution Model The Unified Comminution Model (UCM) was formulated with the vision of bringing all comminution models onto a common base. The structure of the model relies on knowledge of the mechanical environment in the comminution devices to predict the modes and rates of collision in a device. A detailed understanding of the breakage modes and an ability to correctly test these modes for the ores in question is then required to feed into the UCM. A model structure has been developed that has the capability of dealing with multiple modes of breakage, such as low energy impact surface damage, chipping, sliding abrasion, cumulative impact body breakage and the transition of rock between modes. A critical review is presented on the shortcomings and limitations of utilising the discrete element method (DEM) to provide the mechanical environments. The assumptions and applicability of utilising DEM in milling models are presented and proposed routes to building a realistic mechanistic model are proposed. Based on this more realistic measures of collision energy have been derived from the DEM simulations, which better mimic the real breakage tests. Generic forms of the collision energy distributions have been observed and developed into functional forms for use in the simulation environment. The method of application of this model to a pilot SAG mill is presented.

Sep 13, 2010

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

The objectives of this paper are two-fold. First, it will show what problems can arise when single estimated values are substituted for a distribution of values when evaluating an open pit mine project in the face of uncertainty. Secondly, it will show how the ability to deal with uncertainty and risk in mine project evaluation can have a significant impact on the ownersÆ and stakeholdersÆ investment decision-making. Here a new mine evaluation framework, the integrated valuation/ optimisation framework (named IVOF), is introduced as an alternative tool for mine project evaluation where uncertainty and risk are incorporated in the evaluation process.

Jan 1, 2009

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

By Charles T. Baroch

RESEARCH strengthened the position of cesium as the preferred material (commonly but erroneously called "fuel") for ionic propulsion engines. Its use as an element of the plasma thermocouple for generating electricity also seemed more likely. Domestic Production.-No domestic ore of cesium and rubidium was produced. San Antonio Chemicals, Inc., San Antonio, Tex., and Maywood Chemical Works, Maywood, N.J., continued to produce cesium and rubidium compounds including carbonate, chromate, hydroxide, nitrate, sulfate, and all four halides. Rocky Mountain Research, Inc., Denver, Colo., began producing various cesium and rubidium salts. American Potash & Chemical Corp., Los Angeles, Calif., offered cesium and rubidium for sale.

Jan 1, 1960

By P. F. Ledwaba

South Africa?s Northern Cape Province houses a variety of gemstone minerals. Diamonds remain the primary gemstone in the province, but there are also tiger?s eye, sugilite, rose quartz, jasper, amethyst, amazonite, tourmaline, and topaz deposits. This paper gives an overview of the tiger?s eye (TE) mining sector in the Northern Cape, with the objective of assessing the potential of TE to contribute to job creation and poverty alleviation in the province. Mining of TE started in 1803, but gained momentum during the 1960s. Mining is conducted on a small-scale basis, and in most cases without any legal framework. The majority of the residents are not benefiting from TE. It has been reported that an estimated R700 000 to R800 000 worth of TE is leaving the country every week through illegal trading. The potential for TE mining to contribute to socioeconomic development is hindered by illegal operations, lack of technical skills and knowledge, exploitation by dealers, lack of market information, community rivalries, and absence of value addition. A multi-stakeholder approach is needed to formalize the sector and reap the benefits. Mintek is spearheading a TE project in the Prieska area of the Northern Cape, which aims to establish a gemmological centre where TE can be beneficiated into saleable and high-value products..

Jan 1, 2014

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

Based on relative CO2, N2, and 3He contents, geothermal systems of the Taupo Volcanic Zone, TVZ, can be subdivided into two major groups: arc-type systems, associated with andesitic magmatism along the eastern boundary of the TVZ, and rift-type systems over its western parts. The highly increased N2/3He, CO2/3He and CO2/Cl ratios of the former are ascribed to entrainment of large proportions of volatiles of subducted, marine sedimentary origin. The largely rhyolitic, rift-type magmas are assumed to have formed from volatile-depleted, residual melts. Correlations of Cl and CO2 with heat contents suggest that formation of the two types of source magmas involves mixing of two end member components: a low-volatile melt with a heat/Cl ratio of 25 Ml/mol (0.7 MJ/g), and a low Cl vapor with a heat/CO2 ratio of 5 Ml/mol. On the basis of these values, the heat associated with andesitic magmas is found to be carried in close to equal parts by both vapor and melt; for the rhyolitic melts the proportion contributed from the vapor is only about 2%. The heat/He ratios of the rhyolitic source magmas for the rift-type geothermal discharges from the TVZ of 0.12¦0.05 Ml/pmol is within the range of 0.05 to 0.2 Ml/pmol of the upper mantle. The higher heat/3He ratios for the arc-related magmas of 0.4¦0.2 Ml/pmol are likely to be due to the high proportions of heat carried in the form of a separate, low 3He vapor phase derived largely from subducted sediments.

Jan 1, 1995