Search Documents

By A. Dave Mackintosh

In 2001, at the CIM AGM in Quebec, a paper discussing poor ground conditions in a newly opened area at Agrium?s Vanscoy Potash Operation?s, suggested load transfer around old workings as a possible reason for the early room failure. High closure rates are expected in deeper regions however the rapid failure of walls immediately behind the face resulted in protective guards being mounted on and behind the borer. The high closure and early rib failure continued well past any reasonable distance to be explained by load transfer around old workings and investigations continued into possible reasons other than simply depth. Detailed investigations into the mineralogy and crystal fabric of the ore zone provided one possibility, which combined with a changed borer cutting profile are now believed to have contributed greatly to the poor conditions.

Apr 1, 2005

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By Murray Jacobson

A method for determining airborne trona dust concentrations using a midget impinger was developed. During sampling, the trona dust, composed of sodium carbonate and bicarbonate, dissolves in the collecting medium (water). Resulting solutions are then titrated using 0.1 [N] hydrochloric acid solution. The mass concentration of the trona sample is determined from a calibration curve relating the volume of acid required for neutralizing a collected sample to the mass of the dust. Test results obtained using this method are equivalent to those obtained using a gravimetric sampling method.

Jan 1, 1971

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

The objective of current efforts by AQUILA Mining Systems Ltd. is the continued development of computer-based systems and techniques to automatically process and interpret monitored performance data from surface blasthole drills and mining shovels, and the management and coordination of these pieces of equipment by GPS (Global Positioning Systems).

Jan 1, 1995

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By Wayne Rogers, Kell Monro, Arthur Pacunana

The Phu Kham Copper-Gold Operation (PKM) is a large-scale open pit mine located in northern Laos. It was developed and is operated by Phu Bia Mining Limited (PBM) a Lao-registered subsidiary company of Australian incorporated, PanAust Limited. Production commenced at Phu Kham in 2008. Since the second half of 2016, there has been a significant increase in ore hardness and this has negatively impacted the PKM concentrator and resulted in lower SAG mill throughput rates. Over the remaining life of mine, the changing ore body and increase in ore hardness is forecast to continue as the pit deepens and the availability of softer blending ores reduce. To manage this risk, PKM initiated a Hard Ores Management Program to determine the most effective way to improve the mill throughput of harder ores. This involved conducting a number of innovative and process control driven blasting trials to optimize run-of-mine (ROM) fragmentation and other blasting outcomes. From 2016 to 2017, the performance of high powder factor blasting, electronic detonators and fast timing, high velocity of detonation (VOD) explosives, double-priming, and deck blasting, were individually and systematically assessed. The success of each blasting trial was then based on a ‘value for money’ criteria. This criteria is a cost / benefit analysis that weighed-up the additional cost to implement the trial against the measured improvement in mill throughput. Electronic and high VOD 90:10 emulsion:ANFO blasts were determined to have the best value for money, achieving an increase in mill throughput of 54% compared to baseline. This paper discusses how the implementation of an innovative and process control driven blasting trial methodology was able to successfully manage the hard ore challenges at PKM. In addition, this success was achieved without any major cost implications, safety incidents or process plant set-backs.

Jan 1, 2018

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By R. Hummel

When the slope angles of the southern side of the Venetia open pit were required to be flattened by some 20 degrees after an analysis completed by De Beers geotechnical engineering in conjunction with SRK, the additional waste stripping tonnage generated was in the order of some 70 million tons. The potential cost of having to move this tonnage had a significantly negative effect on the Net Present Value of Venetia Mine, challenging the viability of the third pushback and rendering a potential fourth pushback completely uneconomic. This paper details some of the innovation that went into the design and planning process undertaken to virtually negate the instantaneous effect of the flattened slope angles and the associated waste tonnage as well as further improve the NPV of Venetia Mine and bring the fourth pushback back into economic viability. This process has become known as NPV+ and is anon going exercise in waste reduction/deferment and revenue advancement.

Jan 1, 2001

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

A field method combining solvent extraction and paper partition chromatography permits a simple and rapid semiquantitative estimation of gold in siliceous, argillaceous and sulphide ores. The method will facilitate the eyaluation of prospect samples in which the gold is too fine for separation by panning.Ethyl alcohol-hydrobromic acid mixtures are suitable for chromatographic development of the gold complex, and give clear reproducible definition of the gold zone. Substitution of commercial "methylated spirits" for the ethyl alcohol gives equally good definition, improving the potential of the method for field use.A batch of six samples in the range of 0·5 to 5·0 dwt/ton can be completed in two hours. The range may be extended by simple modification to higher or lower values.INTRODUCTIONIn a chromatographic method described previously (Lever 1958, Nevill and Lever 1959), gold from a standard volume of ore clamped between -plate glass was extracted by aqua regia on to the paper. After cautious drying the chromatogram was developed by an ethyl acetate-nitric acid-water mixture and gold was identified by spraying with stannous chloride solution. Sensitivity of the method in the low range was poor. The brown line obtained in the 1-3 dw/j ton range, caused by movement of gold in the reduced form, was not considered to be a satisfactory confirmation of the presence of gold. It was felt that the method would be improved by using a more elegant extraction and applying developing conditions which would produce a well defined purple line at all gold values. Iron was a limiting factor, and a method of eliminating its interference was needed.The method now developed overcomes these shortcomings, and gives a reliable result with a purple line for assay values of 0·5 dwtjton and over. Gold is dissolved from an...

Jan 1, 1964

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

Difficulties were experienced in the identification of carbonate minerals intimately associated with iron oxides in the so called carbonate ore, which occurs at depth in the Iron Duke Orebody.Determination of refractive indices by examination under the microscope using the immersion method, together with inferred chemical composition indicates that dolomite and parankerite are common constituents. Histograms of the manganese and sulphur contents strongly suggest that manganese is associated with the carbonate minerals, and that the highest sulphur assays occur near the base of the carbonate body.From the present work it is concluded that refractive indices indicate only a very approximate composition for carbonates of the parankerite type.The different carbonate minerals occur in irregular zones.INTRODUCTIONThe Iron Duke deposit is situated in the southern portion of the South Middleback Range on Eyre Peninsula, S.A., 30 miles from Whyalla. (Fig. 1).Drilling at Iron Duke revealed a large body of so called carbonate ore, which was tested in detail at cross section 1000 ft. S by three diamond drill holes, DDH.57, 67 and 78. (Fig. 2)Most specimens of carbonate ore described below were obtained from DDH 67 and 78.GENERAL GEOLOGYThe South Middleback Range is composed of two parallel ridges trending north-south. The Iron Duke orebody is situated on the southern portion of the western ridge. (Fig.1) .The rocks of these ranges belong to the Middleback Group which rests on a gneiss complex. Their age is considered to be Middle Precambrian or late Archaean.

Jan 1, 1963

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004