Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By Betty L. Gibbs

Geologically simple deposits can be modeled quickly and easily with inexpensive gridding and mapping software. Hundreds of mines around the world use RockWorks99 and Surfer 7 for generating contour maps, producing log plots and cross sections, and performing other useful geological calculations. These programs are used by many mining operations as their only modeling and graphical software or they are used in conjunction with larger systems. The investment in learning time is low and the programs produce reasonable quality results with standard computing equipment. RockWorks99 and Surfer 7 provide a good level of capability while maintaining high quality technical integrity. Both programs are used for many applications in mining, oil and gas, environmental and other fields that require analysis of spatial data.

Jan 1, 2000

By Franciszek Letowski

"Recovery of precious metals associated with a sulphidic matrix has an important economic effect on complex sulphide ore treatment. Because a significant portion of the silver and gold associated with pyrite are rejected to tailings during the selective flotation of pyritic Zn-Pb-Cu ore, other ore processing routes have been investigated.Direct leaching of the ore with ferric sulphate solution followed by separation of different components of the solid suspension by flotation was applied. Such a process allows for: production of zinc sulphate solution; transformation of galena PbS to insoluble lead sulphate PbS04 and its accumulation in a non-floatable fraction together with precipitated geothite FeOOH and other insoluble gangue minerals; separation of sulphur and non-decomposed sulphides in the floatable fraction.Laboratory research carried out on the ore samples from an Alaskan pyritic deposit from the Delta region indicates that gold and silver are mostly concentrated in the floatable fraction.Total recovery of zinc from the ore attains 96.5% to 98.5% after ferric sulphate leaching. About 85% of copper was extracted from the ore during the ferric sulphate and subsequent ferric chloride leaching, and about 6% of the copper remained in the non-floatable fraction and mixed fraction during the leaching-flotation step. Extraction of lead from the nonfloatable fraction during leaching with calcium chloride solution attained 98% to 99%. Extraction of silver from the floatable fraction during leaching with ferric chloride solution reached 98%. Extraction of gold from the floatable fraction during cyanide or thiourea leaching reached 71% to 89%. The results of the laboratory research are presented."

Jan 1, 1987

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By A. P. N. Sutherland

Pipelines for transporting high concentration slurries are often designed using methods applicable to homogeneous non-Newtonian laminar flow. Many industrial slurries though comprise coarse particles in a non-Newtonian carrier fluid, and existing experimental evidence from tests with such slurries demonstrates that they are not homogeneous. Under laminar shear conditions the coarse particles settle, even in statically stable carrier fluids. To understand this better, the Institute of Materials Science and Technology (IMST) at Cape Peninsula University of Technology (CPUT) is conducting ongoing research into the flow of these high concentration non-Newtonian settling slurries. Since pressure gradient and flow rate measurements alone are insufficient to adequately model the flows, an electrical resistance tomography (ERT) instrument developed by the University of Cape Town (UCT)was incorporated into the pipe test loop to determine pipe cross-section concentration and velocity profiles. The software developed to do this is modular and allows different image reconstruction and cross-correlation algorithms to be implemented and tested without significantly changing the rest of the application. At a total frame capture rate of 566 frames/sec a 2.67 GHz Intel Celeron processor with 500 MB of RAM is fast enough to calculate and display velocity profiles in ?real-time? at an update rate of one profile every two seconds. Examples of experimental concentration and velocity profiles obtained using the system are shown and some proposed improvements/extensions to the system are listed.

Jan 1, 2008

Upgrading of Superfine Low-Grade Haematite Ores by Reverse Floatation Direct Reduction Low Intensity Magnetic Separation Process

Sep 13, 2010

By Frederick H. Raab

An electromagnetic (EM) system for the location of trapped mine workers at coal-mine (300 m) depths has been developed. The use of such a system in deep mines (1-km depth) requires transmission at extremely low frequencies (ELF) and a reduction in the effective noise level beyond that which can be obtained by acceptable Integration times. Automatic-noise-cancellation (ANC) techniques reduce the effective noise level by combining several received signals that contain correlated noise. Such signals can be obtained either from a remote magnetic antenna or a local electric antenna. During Phase III of this program, real ELF noise data were acquired and used to test the ANC algorithms developed during Phase II. The ELF noise data were obtained from analog recordings made by Develco under another Bureau-of-Mines contract. Digitization was accomplished by an ND converter that was added to a GMRR computer. Phase III tasks Included preparation of software for digitization, computer-computer communication, data processing, and statistical analysis. Useable data were obtained from eleven half-hour tapes containing noise from one axis of the primary antenna and three axes of the remote antenna. The overall average Improvement in SNR was 4.1 dB. However, the average Improvements for the Individual X, Y, and Z axes were 4.2, 11.9, and -1.9 dB, which roughly follow the observed noise power. Nonlinear processing was not effective with this noise.

Jan 2, 1984

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By Trevor Howie, Mal Edwards

"Thiess Contractors Pty Ltd. designed and operate the Mt Owen Mine in the Hunter Valley of NewSouth Wales, Australia on behalf of the owners of the mine, BHP Coal Pty Ltd. The mine is a multiseam open cut coal operation. Mining by Thiess commenced in September 1996 following thecompletion of the coal preparation plant. The location of the mine is shown below on Figure Al."

Jan 1, 1997

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

Many mining operations generate seismic signals. They come from blasting and from underground mine failures such as rockbursts, longwall first caves, coal bumps and pillar collapses. Traditionally, seismic motions have been of concern on a local scale because they could create damage to structures at the mine site or at neighboring locations. Recently, there has been much interest in the Comprehensive Nu-clear-Test-Ban Treaty (CTBT). It prohibits any kind of nuclear explosion, anywhere. So distinguishing signals of mining operations from a possible nuclear explosion becomes important. An international monitoring system (IMS) is being implemented to verify the Treaty when it is ratified. It includes a large number of seismic stations capable of recording signals at regional (200 to 2,000 km or 124 to 1,240miles) and teleseismic (more than 2,000 km or 1,240 miles) distances.

Jan 1, 2000