Search Documents

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

By Honeycombe R. W K, Greenwood J. N

Powder metallurgy has been developed rapidly in the last twenty years by overseas metallurgists. The technique of making the powders and their subsequent pressing and sintering into useful forms has' only been introduced into Australia under the stress of war-time economic conditions.The technique involved has very little in common with our usual methods of fabricating engineering alloys by melting the ingredients to a homogeneous mass, followed by casting to shape or casting to ingot form and shaping by application of pressure-so-called mechanical working. On the other hand, the technique includes operations, such as milling and sizing, familiar to the primary metallurgists.The compacting of metal or other powders finds important application in two outstanding fields of engineering production: (a) in making porous bearings and contact brushes, in which such a material as powdered graphite can be incorporated; (b) in making cutting tool tips of hard -carbides, which have a melting point too high to make casting feasible, and which would be too brittle in the cast condition in any case. In both these cases; the final article can be made of the desired shape and size (subject to shrinkage allowances) whilst the compact is in a soft and readily machined condition a consideration of great importance in connection with the hard carbides.In order to develop the necessary equipment and technique and at the same time to assisil in the war effort, it was decided to divert the research work of the Metallurgy Department of the University of Melbourne to the problems associated with the production of hard carbides from local raw materials and the sintering of such into tips for cutting tools. Since this work was started at least two industrial concerns have started to produce these materials in the Commonwealth.The work. to date has included (a) the purification of crude cobalt oxide from Risdon and the reduction of this to metal Particles of less than 10 p. diameter; (b) the production of tungsten powder from King Island scheelite and its conversion into tungsten carbide with particle size less than 4 p. diameter; (c) the sintering of the latter product, using the former as a bond; (d) the production of titanium carbide from titanium dioxide; (e) the separation of columbium and tantalum oxides from a Northern Territory tantalite, and the conversion of these into the respective carbides.

Jan 1, 1942

By Tom Treleaven, Andrew Williams

Several contracts were let in Greenwich, Connecticut, for the installation of a sanitary sewer. The majority of the excavation was in rock and involved numerous challenges due to the following conditions:

Jan 1, 2003

By A. F. S. Schoukens

The Mintek Thermal Magnesium Process (MTMP) was successfully demonstrated in November 2004. The pilot plant was operated continuously for 8 days, during which about 30 tons of magnesium producing recipe was smelted in a DC (direct-current) arc furnace at a feed rate of 525 kg/h. The furnace was operated at power levels of 700 to 850 kW, resulting in slag tapping temperatures of 1600 to 1700°C. Magnesium extraction averaged 77 per cent and was as high as 85 per cent during good extraction periods. The furnace generated 70 to 85 kg/h magnesium vapour that was delivered to the condenser where the temperature was controlled at 680 to 720°C. The novel condenser captured the magnesium in a liquid state, which was tapped periodically as required. In total, 15 magnesium-tapping operations were carried out, proving that online magnesium tapping can be consistently performed without any major difficulty. About 3500 kg of crude magnesium was produced with a quality that was similar to, if not better than, that of the Magnetherm?s crude metal. The condensation efficiency averaged 85 per cent, and peaked at 87 per cent, which exceeded the target of 80 per cent set for the pilot scale. A brief magnesium market study was also carried out. Magnesium demand is expected to keep on growing by 6 to 8 percent over the next 10 years and could reach 2 million tons by the year 2020. The growth will be mainly in the die-casting sector for light-weight automotive applications. China is likely to remain the dominant supplier of primary magnesium but competitively priced non-Chinese magnesium producers will be needed to sustain the anticipated growth of 6 to 8 per cent over the next 10 years. In addition, a prefeasibility study was undertaken for a commercial plant. The study confirmed the relatively low capitalcosts of the MTMP process, as well as the competitiveness of theoperating costs, as compared to the industrial electrolytic process.

Jan 1, 2006

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

Background information, formulae and a systematic set of procedures for estimating capital and operating costs for open pit mining equipment are presented in this paper. Firstly, equipment capital costs are required. These can be obtained from either suppliers, contractors or from first principles. The equipment is then divided into cost elements. Typically these are fuel and power requirements, spare parts consumption, wear items such as tyres, teeth and drill bits and finally repair and operating labour requirements. By consideration of the cost and life of each element a base cost can be derived. The base cost is then adjusted to suit specific site conditions such as the proximity to spare parts suppliers, the duty or ground conditions and the management and operator skills specific to the site. Hence, the same item of equipment can be costed to reflect different operations. Included are tables and data for typical plant items. Several examples are also given to illustrate the methodology being presented. The intention is to provide a set of procedures to allow costs to be built up from base level in a systematic and repeatable way. Applications for these costs include feasibility studies, budgetting and data for economic analyses.

Jan 1, 1990

By T Leach, B Fulton, R Stewart

Gold mineralisation at Porgera is inferred to have been derived from a deep differentiated magmatic source which is capped by a series of (now tilted) inward dipping sills and stocks, which comprise the Porgera Intrusive Complex. An arc normal transfer structure provides a conduit, at tile intersection with an arc parallel structure, into which basic magma derived from tile deep melting of mantle material has been emplaced. Two phases of mineralisation display an association with late stage feldspar porphyry intrusives. Stage I carbonate-base metal-style gold mineralisation occurs as early quartz-sericite, then massive sulphide and late zoned Mn-Fe-Mg-Ca carbonate vein/breccias. Magmatic fluids derived from the deep magma source, are interpreted to have migrated along me margin of a feeder stock to the sills, and south to Waruwari. Stage II epithermal Au-Ag quartz-style gold mineralisation occurs as early fluidised breccias and carbonate veining, followed by zoned quartz-roscoelite-carbonate-gold vein/breccias, and late carbonate and/or sulphate open space infill. Magmatic fluids are interpreted to have utilised the same plumbing system as the late stage feldspar porphyry intrusive, and then migrated into the Roamane Fault which was dilated by; dextral rotation on elements of the transfer structure, normal faulting, and refraction around the competent footwall hornblende diorite. Bonanza gold is localised in a jog in the Roamane Fault, hangingwall splits and at intersections with cross structures. Bulk low grade Stage I gold has been deposited by the mixing of magmatic fluids with cool gas condensate waters, whereas high grade Stage II gold mineralisation resulted from the rapid quenching of mineralised magmatic fluids by oxygenated groundwaters.

Jan 1, 1995

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By D. Kidby, A. Briggs

"Vitrokele ™ is a synthetic adsorbent, using chelating groups on large polystyrene beads, developed in Canada over 7 years ago, and first commercialised in 1985 to recover noxious metals from plating wastes.Pilot plant trials have been performed in Australia and Canada to demonstrate the recovery of cyanide and removal of metal cyanide complexes from gold plant effluent using Vitrokele1 M 912. The pilot plants comprise a simple adsorption train (similar to a CIP circuit) followed by complete elution facilities, so that loaded Vitrokele™ can be stripped and returned to the adsorption circuit.An account of these campaigns is provided, showing the reduction of total CN levels from over 200 ppm to less than 0.5 ppm and Cu levels from approximately 100 ppm to less than 0.3 ppm in treated tailings.Comparisons between pilot plant results and laboratory test data are given and probable future work on the process and its application to the gold mining industry is discussed.INTRODUCTIONThrough millions of years of evolution, life forms have developed specialised molecules with exceptionally high affinity and selectivity for various metals such as iron, cobalt, zinc and copper.In the early 80's professors at the Faculty of Medicine of McGill University engaged in research on the extremely efficient ways that living cells captured trace metals essential for life.As research progressed, it became evident that the special molecules used by biological systems to capture metals could be synthesized to capture selected metals with similar efficiency from water or other solutions.The technology was first commercialised in 1985 to recover noxious metals from plating wastes with compositions applying the special molecules (chelating groups) on vitreous particles (hence Vitrokele™). To date approximately three commercial Vitrokele™ plants have been installed for treating plating waters in Ontario and Quebec."

Jan 1, 1992

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012

By Luis Martín Tejeda

El presente texto señala cómo los parámetros geotécnicos de resistencia y deformabilidad pueden generar mayor confiabilidad en un estudio técnico. En este sentido, la literatura geotécnica indica que los resultados obtenidos a través de métodos numéricos son sensibles a la variación de estos parámetros y que algunas propuestas de cálculo son más satisfactorias. Para ello, se utilizó el criterio de falla de Hoek & Brown en términos de Mohr–Coulomb, donde se presenta un ejemplo aplicativo para mineria superficial, en el cual el factor de seguridad y la probabilidad de ruptura del macizo rocoso son calculados mediante métodos geoestadísticos aplicados a la ingeniería de rocas (FOSM - First Order Second Method y puntos de estimación de Rosenblueth).

Sep 19, 2006

By Miguel A. Farfán

El presente trabajo describe los criterios de productividad en el diseño de tajeos para vetas irregulares a través del método de explotación de corte y relleno. Dicho método es factible -en tanto es capaz de captar el desmonte producido por niveles superiores que requieren avances, así como también en los inferiores. De forma que se pueda agregar valor por la función que cumple en la producción sino por las demás actividades. Finalmente, en el caso de los índices de productividad, el control se debe manejar a un nivel de planeamiento que pemita corregir procesos muy costosos, faltos de continuidad y genere equipos parados, tiempos muertos, daño a equipos o recursos.

Sep 12, 2005

By T. Ertekin, X. Dong

This paper identifies the need for the development of specialized inverse solution techniques for the analysis of pressure transient data for the characterization of the transport and sorption properties of coal seams. Central to the proposed inverse solution technique is a specially structured artificial neural network (ANN). The most important transport and sorption characteristics of coal seams are butt and face cleat permeabilities, macropore porosity, Langmuir volume constant, Langmuir pressure constant, and sorption time constant. Conventional methods, such as type curve matching techniques and laboratory-derived measurements are handicapped in terms of being representative over the entire domain of interest. In this paper, we utilize analytical forward solution techniques for various combinations of characteristics of coal seams to generate training and testing patterns. These training patterns are shown to an ANN structured to learn the ubiquitous non-linear relationships that exist between coal seam properties, input conditions and the pressure transients measured. The trained networks are then extensively tested to ensure that they have effectively learned the training patterns. In the final stage of the development, the networks are run in the prediction mode. The responses of the networks are found to be in agreement with the input data. The developed networks are able to generate results generally within 5% error margin for permeability and porosity and 20% error margin for the sorption characteristics of coal seams. A number of examples highlighting the capabilities and degree of effectiveness of the network in characterizing the coal seams areincluded. Keywords: artificial neural networks (ANNs); coal seam characteristics; pressure transient analysis

Jan 1, 2003

By D. Ouellet, G. Gagnon, B. Simser, V. Falmagne

The mining sequence at Noranda’s Bell- Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the redimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Jan 1, 2004

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

This paper describes certain analytical methods used at the Rosepery Mine and Treatment Plant of the Electrolytic Zinc Co. of Australasia Ltd., which are not generally in use and may therefore be of more interest than a description of the normal routine methods which are used in most of the mining assay laboratories of the Commonwealth, and which have been published previously.The ore mined and treated at Rosebery is of a complex nature and demands closer control in the concentrating plant than is necessary on some other similar mining fields.It is necessary for the mill shift supervisors to keep constant control on the grade of lead and zinc concentrates produced on their respective shifts, and further, it is essential to maintain an economic compromise between grade of concentrates and the recovery of the particular concent:t:ate. This necessitates a more frequent check on concentrate grade tp.an is provided by the daily assays carried, out by the assay office. Rather than employ trained ,assayers on shift work, "quick methods" of analysis, which could be carried out by the operators, 'were adopted.'In such methods, it is desirable that the necessary manipulation should be reduced to the following:-a. Taking the sample, drying and mixing.b. Weighing the necessary amount of sample-for assay.c. Adding the reagents for use in the assay without change of beakers.d. Titration and calculation.Such a contraction of, the normal technique would be impracticable for many determinations, but in the case of lead...

Jan 1, 1949