Search Documents

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By R. F. Favreau, Patrice Favreau, Dennis Mahan

Cast blasting is becoming more and more popular, not only in coal mines but also in other operations which require excavation of an upper layer of waste rock to uncover temporarily and excavate a layer of ore, which may for example be material for the fertilizer industry.

Jan 1, 2014

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By K Niiranen

Luossavaara-Kiirunavaara AB (LKAB) operates one iron ore mine, three concentration plants and three pelletising plants in Kiruna, Sweden. The current methods of separation at the beneficiation plants are low intensity magnetic separation (LIMS) and reverse apatite flotation, where the wet LIMS stage is regarded as the crucial part of silica separation from the ore. Because future silica levels are expected to increase in the incoming material to the beneficiation plants, geometallurgy has become an important area of development and research.A laboratory-scale methodology was developed for the systematic characterisation of the ore for mineral processing, with the focus on the high silica ore type B2 and newly discovered subtypes. This methodology combines mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN®) is used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and the degree of liberation and intergrowth of magnetite and silicates. An essential stage in the systematic characterisation of the ore deposit for mineral processing is the estimation and simulation of different parameters from the laboratory scale to the full scale at the concentration plants. This is achieved by using empirical models based on the data collected at the mineral processing plants. As the first step to implement the geometallurgical information, the current geological model is reconstructed with the mineralogy and the two, newly defined subtypes of high silica ore type B2 are separated into different domains.To study the reduction of the SiO2 content in the magnetite concentrate, a large-scale reverse cationic silicate flotation laboratory test program was initiated in early spring 2016. This program investigated potential silicate flotation in the beneficiation plants at the Kiirunavaara site. The second target is to implant mineral processing parameters into the block model based on the new geological model. This information provides a good basis for making a prognosis for mine planning and a quality prognosis regarding the crude ore for mineral processing.CITATION:Niiranen, K, 2017. A geometallurgical perspective on a high-grade iron ore deposit at Kiirunavaara, northern Sweden, in Proceedings Iron Ore 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By D Craw

Bulk ore tailings from the Macraes gold mine gold extraction process are stored in a large (ca 0.6 km2, 80 m deep) mixed tailings impoundment whose pH is maintained near 8 by natural rock neutralizing capacity. The mixed tailings will be stored in this impoundment in perpetuity after mining ceases. Confidence in the long term environmental stability of these tailings can be gained from examination of mineralogically and chemically similar geological situations in the immediate vicinity. A sequence, typically about 5 m thick, of sands and gravels derived from the Macraes mineralized zone 12 000 to 28 000 years ago contains rounded detrital sulphide mineral grains which are unoxidized despite close proximity to the surface and occasional incursion of oxygenated waters. Saturating water pH is currently 7-8. Sands with 0.2 to 0.8 wt % organic carbon host sulphate-reducing bacteria (SRB), and localized cementation by authigenic framboidal pyrite has occurred. Comparison of the 28 000 year-old sediments with the modem tailings suggests that similar chemistry will prevail, possibly with deposition of authigenic pyrite in the tailings, in the long term. As long as the present slightly anoxic and circumneutral pH environmental conditions are maintained in the mixed tailings dam, sulphide decomposition and acidification are unlikely. These sediments provide a plausible geological analogue for long-term benign storage of the mixed tailings impoundment.

Jan 1, 2000

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By L. du Plessis

The name FISH (Fully Integrated Sort House) refers to a class of technology deployed at Jwaneng Mine final diamond recovery. The FISH concept is based on three pillars, namely: ?Improved sorting efficiency FISH is based on laser technology, which is more efficient than hand sorting for certain product categories. Laser sorting is based on measuring in-elastically scattered light from molecules and this is referred to as Raman spectroscopy. The Raman scattered light occurs at wavelengths that are shifted from the incident light by the energies of molecular vibrations ?Availability of production information Roller gap diamond size distribution information is generated on line for upstream process optimization ?Improved product security A ?hands-off? philosophy reduces security risk during operation and maintenance of the plant. In addition, a number of lessons were learnt about the application of new technologies in the industry: ?The required human competency profile demanded by new technology should match the available competencies of the operational staff ?An integrated information management system should be fully functional for both production management and diamond control purposes ?Operational feedback must be correctly evaluated to identify design, maintenance, training and operational issues so as to accelerate the maturity of the new technology within the time span of the sustainable operations project ?Project execution and technology maturity risks have to be evaluated and married to ensure risk mitigation by means of suitable project resource and contracting model selection.

Jan 1, 2003

By K Shannon, A Shaw

The Hilton and George Fisher deposits occur 22 and 24 km north of Mount Isa, NW Qld, Australia respectively. Both deposits occur as deformed Proterozoic, sediment hosted, stratiform orebodies hosting Pb-Zn-Ag (Hilton) and Zn-Pb-Ag (George Fisher) mineralisation. The two deposits are separated by approximately 2 km of strongly faulted barren shales, mudstones and siltstones along strike. Despite this, correlations between the Hilton and George Fisher deposits have previously been assumed on the basis of textural, lithological and geochemical similarities, but previously lacked specific details to prove exact stratigraphic matches.Feasibility drilling allowed broad correlations based on the position of siltstone pillars separating individual orebodies. However the position of continuous potassium-rich, siliceous and cross-fractured tuffaceous marker beds (TMBs) often used as stratigraphic markers within the Hilton Mine were initially unrecognised within the George Fisher stratigraphy where they are erratically silicified and often not cross-fractured resulting in correlations being difficult to prove. As a more detailed knowledge of TMB locations at George Fisher was gained it was possible to look for corresponding TMBs within the Hilton orebodies. Recent underground stope definition drilling at the two locations enabled specific TMBs, stratigraphic units and even individual sedimentary beds to be matched between the two locations, despite the large separation between mines.The correlation between the two deposits has implications for future exploration drilling north of George Fisher. If a specific stratigraphic horizon can be determined within one hole, positioning of further drillholes can be more accurately planned. The significance of having stratigraphic matches between Hilton and George Fisher also has implications for correlations with other Isa Valley deposits. Convincing preliminary TM and stratigraphic correlations have already been made between George Fisher and the Isa Lead Mine 24 km to the south.

Jan 1, 2002

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

By Mills R, Shannon W. T, Finch J

As an extension to investigations into methods of upgrading the Iitania content of ilmenite concentrate from beach sands using 100 g/day, a small pilot plant treating 23 kg/ day of ilmenite was used.In the pilot plant the iron oxide in the ilmenite was reduced to iron at 1200°C using carbon (coal/char) without melting the material, using a tunnel kiln heating cycle, the charges contained in saggars, The iron was then separated from the titania fraction by ball milling, wet magnetic separation, and screening. The resulting magnetic product was high in iron (about 80 per cent Fe) and the non-magnetic product high intitania (about 70 per cent TiO2).From this trial sufficient data were obtained to enable the preparation of a flow sheet for a plant producing 62,300 tonnes/year total products, and an estimate of costs to be made. This has shown that for an estimatedcapital expenditure of nearly $6,000,000 and annual production costs of about $4,000,000, the cost per tonne of high titania product (76 per cent TiO2) would be nearly $70.

Jan 1, 1977

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988