Search Documents

By Franco Oboni, Iain G. Bruce

The design of tailings containment structures relies on well-understood engineering methods being applied consistently. Unfortunately, not all facilities are designed or managed to the same level of competency. To standardize procedures, the Mining Association of Canada (MAC, 1998) prepared a “Guide to Tailings Management.” It recommended review of designs and an assessment of the risks associated with tailings impoundments be implemented during all phases of amine life. This paper describes how the quantitative risk assessment (QRA) process can be used to define risks associated with the design, construction and operation of a tailings management facility. And it discusses how, once the risk tolerability curves (RTC) are defined for a project, they can assist the risk management (RM) process.

Jan 1, 2002

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By A. D. Dalvi

With the current economic situation, the demand for nickel and other base metals has fallen significantly. More than 440 kt/yr world nickel capacity has been taken out of production within the last year, or more than 25% of the total [1]. This situation is similar to that at the end of 1970?s and it will take a number of years for the demand to recover to the levels before the economic downturn. In the meantime, the challenges facing the industry have increased due to diminishing ore grades, more inaccessible and complex deposits, mounting capital and operating costs and the various external pressures which include socio-economic, environmental, and energy challenges. All industries will be faced with paying the ?total ownership costs? in the future. This will only increase the burden on the industry. How to cope with this in what Thomas Friedman calls the ?Energy-Climate Era? [2] will be the most pressing challenge for the next generation of metallurgists and managers. It will force us to take a broader view of the problems and the solutions beyond mere technical. The metallurgists, engineers and project managers will have to look at the overall projects and their objectives in designing the solutions, requiring a top-down strategic approach.

Jan 1, 2009

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013

Small scale gold mining operations in Papua New Guinea (PNG) have been observed to use very low flow rates of water in sluice boxes. In a series of laboratory experiments carried out to determine whether this approach was unsatisfactory or not for their situation, indications were obtained that it had some advantages in the recovery of fine gold but at the cost of considerable throughput. The separation mechanisms operating in such a system are analysed.

Jan 1, 1986

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By C. A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 2001

By Javier Támara

Para aumentar la productividad de la empresa minera es necesario conocer el sistema de aire -en tanto se prioriza los intereses de los clientes, y así se puede suplir todos los componentes necesarios para garantizar una máxima eficiencia y confiabilidad del sistema completo de aire comprimido que va desde el filtro de admisión hasta el punto de uso. En ese sentido, el presente texto describe las estrategias para realizar Solucionazing en ahorro energético y así aumentar la produtividad de los sistemas de aire.

Aug 25, 2002

In their excellent paper, Milev and Spottiswoode have provided quantitative and definitive descriptions of an important phenomenon that hitherto has been largely the subject of conjecture. They convincingly show that ?site-response? can amplify the strong ground motions on the rock-wall of a stressed tunnel by a factor of 10 to 12 compared with the PPV in the solid rock mass (at the same distance from source). This knowledge gives us a firm foundation from which to begin to build an understanding of the mechanism of damage resulting from a rock burst. Regrettably this understanding is still far from adequate, in my opinion. The authors of this paper, however, have made some statements that are too reassuring and which tend to reinforce the sense of complacency that prevails among many members of the rock engineering community on the deep gold mines.

Jan 1, 2006

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical of these processes is that the amount of slag is quite high. The role of slag for the process is thus essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2 based with minor contents of CaO and CrOx. Slags in the FeMn process are principally similar, originating from silicate minerals but can have quite large composition range depending on the manganese ore and its gangue minerals. Characteristic of the FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOx in slag are not only divalent oxides but also contain some higher valent of Cr3+and Mn3+, respectively. In FeMn production conditions the slag consists mainly of Mn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexist in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. The thermodynamics of slags in ferroalloys, production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties

Jan 1, 2004

By F. Freme

For the second time in four years, the coal industry was brought to the forefront of the nation’s consciousness in 2006, as two separate events unfolded which involved coal miners trapped underground. Unfortunately, the tragic results of the 2006 incidents were not the same as in 2002 when the trapped miners were all successfully rescued. In January, two different incidents, both in West Virginia, focused the public’s attention on the dangers that miners face on a daily basis. As a result of these unfortunate events new legislation requiring improvement in safety in underground mines passed both at the federal and state level. In 2006, a total of 47 miners died on the job, matching the total number that occurred in 1995, and more than double the 22 killed in 2005. Notwithstanding those tragic events, coal production in the United States reached another record level in 2006, ending the year at 1.05 Gt (1,161.4 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2006 was 27.1 Mt (29.9 million st) higher than the prior record set in 2005 of 1.03 Gt (1,131.5 million st). Although coal production rose in 2006, U.S. total coal consumption actually declined for the year. Coal consumption decreased in the electric power sector by 1.1 percent, while coking coal consumption decreased slightly. Only the other industrial sector had higher coal consumption in 2006, increasing by 0.3 percent. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports declined slightly in 2006, while coal imports again reached a record level. The excess production over consumption allowed total coal stocks to increase significantly during the year, as electric generators rebuilt their stockpiles that had fallen substantially in 2005 because of missed shipments in the second half of that year.

Jan 1, 2007

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By J. M. A. Geldenhuis

This work is concerned with studying possible reactions in the ilmenite furnace which may control the product quality of both slag and metal. Two different approaches were followed: comparing actual furnace slag compositions with the calculated equilibrium values and using commercial oxygen probes to measure the effective partial oxygen pressure in the slag and metal. It appears from a comparison of actual furnace slag compositions (in terms of the distribution coefficient of vanadium) with equilibrium values, that the TiO1.5-TiO2reaction may fix the effective partial oxygen pressure for the vanadium reaction. This possibility was tested using commercial oxygen probes (traditionally applied during steelmaking) to measure the effective oxygen partial pressure of both the slag and liquid iron in Iscor?s 3MVA pilot plant ilmenite furnace. From these measurements, it appears that commercial oxygen probes containing zirconia solid electrolytes can be used to measure the effective oxygen potential of both the slag and liquid iron. This oxygen activity correlates well with the FeO content of the slag. The results, furthermore, clearly illustrate that equilibrium conditions are not attained in the ilmenite furnace during the production of high titania slags, since the effective oxygen potential of slag and metal differ substantially.

Jan 1, 1999

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By N Merry, T Cocks

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and composition.   A major application of this technology is in mapping mineralogical variations within hydrothermal alteration systems. Using actual case study examples this paper introduces two approaches to using the PIMA data: 1. for directly mapping alteration systems and using the PIMA data to provide vectors to mineralisation, and 2. for establishing empirical relationships between geochemical data and PIMA spectral data. These applications demonstrate that this technology can be an invaluable tool for targeting and mapping alteration and mineralisation.

Jan 1, 1995

By K. Peake, A. Dalvi, V. Hernandez, S. Chang, M. Oliazadeh

"Ironstone Resources Ltd. is developing the Clear Hills oolitic iron ore deposit in northwest Alberta, Canada. Sources of oolitic iron ore worldwide are abundant and ubiquitous, but there is currently no commercial technology to extract iron from oolitic iron ores. Mineral processing of the ore to generate a commercial iron ore concentrate is very challenging due to the nature of these ores. Accordingly, Hatch and Ironstone are developing a new pyrometallurgical process (Hatch Ironstone Chloride Segregation) to produce metallic iron from high silica and high phosphorus oolitic iron ores. Following the chloride segregation process, the treated ore is subjected to fine grinding. The iron is then separated by magnetic separation. The iron grade and phosphorus content of the final product shows a strong dependence on the separation methodology and the grind size. The pyrometallurgical process has been developed and tested at a lab-scale pilot plant. The commercialization of this technology could provide an opportunity for the development of a new alternate iron making technology. This paper presents the results of test work done on the raw iron ore to create a concentrate and also on the products of the pyrometallurgical process for the production of a high grade 90% metallic iron product.INTRODUCTION Oolite is a sedimentary rock formed from ooids – spherical particles with concentric layers. There are a number of large oolitic iron deposits where the mineralogical form features a low iron content and high concentration of impurities making them presently impossible to exploit on either a technical or economic basis. The fifteen largest oolitic iron ore deposits in the world are estimated to contain approximately 337 billion tonnes of iron ore, which would be a significant source of supply for worldwide steel production. A viable process that can economically recover iron from these oolitic iron ore deposits could become an important new technology to meet future demand in the steel industry. Hatch and Ironstone have demonstrated that oolitic iron ores can be exploited to produce direct reduced iron (DRI). Direct reduction ironmaking is a method for producing solid metallic iron using different techniques compared to the blast furnace process, which is the more conventional ironmaking route. The demand for the construction of direct reduction ironmaking plants has increased in response to the increasing demand for crude steel. It is viewed as a method of providing low-residual iron sources to scrap-based steelmaking in electric arc furnaces."

Jan 1, 2014

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002