Search Documents

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By Teele Tuuna, Voglers Eesti OÜ

Blasting operations are a strong and important part in any kind of building and mining industry, a shot-firer profession is one of the oldest professions in the civilized world. It still serves an important and ongoing purpose in the modern economy all over the world. Europe, nowadays, values strongly the mobility of workers, the movement of know-how and labor force between different countries inside Europe. There are no borders for most of the everyday professions.

Jan 1, 2018

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

By F. M. C. C. Vieira

The DEEPMINE Research Programme sought to develop the technology and competence to mine gold safely and profitably at depths of 3 to 5 km. Among the many issues addressed was the stability and support of rockpasses at ultra-depth. It was found that high virgin and mining-induced stresses could cause the walls of rockpasses to spall, leading to the deterioration and failure. A comprehensive programme of numerical modelling was conducted to investigate alternative mining layouts and sequences to ameliorate the problem.

Jan 1, 2005

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

By R. Ramírez, N. Aslin, G. Ríos, T. Bravo, A. R. Almansa

Lacy copper has been an on-going concern at Atlantic Copper for at least 10 years and was first reported to Glencore Technology in mid-2010. Over the past 12 years, many of the plates were replaced due to age and general deterioration however; plate passivation and lacy copper issues have persisted. After analyzing all the possible causes of this phenomena, it was found that the problem is caused by a degradation of stainless steel as a consequence of the deposition of Sb oxides. These deposits act as passivating agents of stainless steel, which reduces the density of copper nuclei, causing defective copper deposit, with low thickness and ductility. After doing several tests for reducing/removing the phenomena, the over-riding factor was found to be the anode-cathode overlap. An adequate overlap eliminates the problem of "lacy copper". This was verified during an eight month trial with anodes extended 2.5cm in length. Longer anode not only avoids the appearance of lacy copper, but also recovers cathodes that already have lacy copper. On the other hand polishing of plates only gives rise to a temporary solution that requires on-going polishing, to avoid the re-appearance of lacy copper. INTRODUCTION The electrolytic copper refinery of Atlantic Copper in Huelva (Spain) was commissioned in 1970 with an initial capacity of 40,000 t of cathodes per year. In 1975 the copper refinery was expanded to 108,000 t/year. From 1994 to 1996, a new expansion together with the implementation of ISA permanent cathode technology led to a capacity of 215,000 t/y. Since 1995, a progressive increase in the current density up to 350 A/m2 has been accomplished, which together with an increase in the number of cells from 1,120 to 1,204, has led to the present cathode production capacity of 290,000 t/y A lack of copper deposition in the lower part of the steel permanent cathodes was first reported in 2010. This phenomenon is known as “Lacy copper” because of the appearance of the copper deposit as it can be seen in Figure 1. The occurrence of this phenomena was relatively low and was assumed to be originated by an excessive anode scrapping. Nevertheless, in December 2015 Lacy Copper was observed in a significant amount of copper cathodes giving rise to the following issues: Increased tramp copper – housekeeping and maintenance problems Poor appearance of cathode deposit and untidy looking bundles

Jan 1, 2019

By J E. Nethery

At the Red Dome and Mungana deposits in north Queensland, Australia, it is proposed that mineralisation and alteration developed as a 'telescoped' overprinting continuum, ranging in style from hypothermal to epithermal, reflecting the major changes that developed in the regional setting over the period circa 325 - 290 Ma. Regional assessment suggests that this also applies to many other precious and base metal deposits within a 40 km length of the host Siluro-Devonian Chillagoe Formation.   A ten stage paragenetic sequence of structural preparation, multi phase intrusion and associated mineralisation, alteration and brecciation is postulated for the Chillagoe district.

Jan 1, 1995

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

Recovery of Precious Metals from Chloride Solution by Magnetite The development of environmental-friendly lixiviants as alternatives to cyanide and the increasing recycling activities to recover precious metals from waste materials have prompted researchers to find efficient methods and alternative sorbents to recover precious metals, such as Au and Pt, from aqueous solutions. This study explored the use of magnetite (Fe3O4) as a sorbent to recover Au and Pt from chloride solutions. Magnetite is a semiconductor and has the capability of transferring electrons both within the solid state and across the solid-liquid interface and has the ability to reduce metal species on its surface. The sorption of AuCl4- and PtCl62- from NaCl solution on commercial grade magnetite powder was investigated by batch-sorption experiments. The effects of pH, contact time, NaCl concentration and precious metal concentration on the recovery were studied. Sorption experiments revealed that magnetite exhibited selectivity towards other metals with the strongest affinity for Au. Both Au and Pt recoveries showed similar pH dependence curves, with peaks at pH 6 - 7. At this pH range, a maximum of 4.4 ¦mol Au/g Fe3O4 and 3.0 ¦mol Pt/g Fe3O4 were recovered after 24 h at an initial metal concentration of 0.05 mol/m3. Increasing the initial precious metal concentration increased the Au and Pt uptake amount by magnetite. It was also observed that the recovery decreased with high NaCl concentrations. The SEM images of the magnetite particles after the treatment showed that gold, which was confirmed by the EDX analysis, agglomerated and were deposited on Fe3O4 surface.

Sep 13, 2010

By Aquiles Vivar

Ante los problemas de sismicidad inducidos por el sistema de minado en la Compañía minera Milpo, se planteó una solución a través del sistema de monitoreo sísmico único, donde se da una distribución espacial de 20 censores entre uniaxiales y triaxiales distribuidos en 3 niveles de producción en el área de influencia de las actuales operaciones para así ubicar, cualificar y cuantificar el fenómeno a efectos de realizar los análisis interpretativos del caso. En ese sentido, el presente texto describe el sistema de monitoreo, cuyo software sísmico está diseñado para determinar nuevas estructuras formadas a partir de los eventos sísmicos pre existentes reactivadas por la sismicidad inducida, así como el desarrollo de planos de isocontornos que permiten la diferenciación entre zonas de altos y bajos esfuerzos.

Sep 9, 2007

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump&apos;s best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By Wayne Trudel, Lloyd McEvers, Lori Clarke, Eric Saderholm, Charles Lynn Bolin, Leroy Schutz

Newmont mine geologists in Nevada are most proficient when applying technical expertise with multi-departmental teams in three main settings. The first is value creation through near-mine discovery, development and reserve conversion. Since 1986, geologists have created substantial net asset value in developing more than 1.35 kt (43 million oz) into quality Nevada surface and underground gold reserves. The second setting is value realization by supporting mine operations with ore control, selective mining, reconciliation investigations and strategic planning. The investment of technical research on reconciliation investigations led to new concepts and practices that highlighted opportunities for large revenue and reserve gains. In 2002, more than $65 million in projected revenue was added to the Gold Quarry south layback. Kriged mine polygon construction and controlled blast heave at the Lone Tree Mine provided millions of dollars in mining efficiencies. High-quality geologic advice in selective mining at the Twin Creeks Mine helped obtain $4.3 million revenue gains throughout 2002-2003.

Jan 1, 2004

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By Maryam Sadeghi, Jonathan Roy, Claude Bazin

"The operation of mineral processing equipments is intimately related to the mineral composition of the ore. However unit performances are usually characterized in terms of metal contents or recoveries as this data is easier to obtain than the mineral contents. This paper describes a method that combines the operations of material balancing and estimation of the mineral contents of the ore. The estimated mineral contents can be used for process analysis and diagnosis of operating problems.IntroductionThe ore that is feeding a concentrator is made of minerals that condition the energy requirements for the ore comminution and the performances of the subsequent separation circuit. Indeed a change in the mineral composition of the ore may lead to lower grinding mill throughput as well as lower recovery or grade of the economical products. Despite this relationship is recognized the mineral composition of the ore is seldom measured or estimated to provide regular information for the diagnosis of operating problems. Some methods such as the QEM-SCAN (Whiten, 2008; Lamberg and Vianna, 2006) are available to measure the concentration of the minerals in ore samples but the method is time demanding and plant operators usually base their evaluation of the plant performances on chemical assays of metals or elements since this data is easier to obtain from ore samples.Usually samples of the streams of mineral processing plants are collected on a daily basis to be assayed for strategic elements. The obtained concentrations are balanced to produce coherent data with the material conservation constraint and then used to characterize the day to day operation of the plant in terms of recovery of valuable metals and grades of the marketable concentrates. The behavior of contaminant elements can also be monitored from this data allowing the operators to explain for instance a lower zinc concentrate grade by a more important contamination of iron. However such diagnosis is only partial as the contaminant element can be transported by different minerals. Indeed the iron contamination of a zinc sulfide concentrate may be caused by an inadequate depression of pyrite or due to another iron carrying mineral. A possible way to answer the question is to determine the concentrations of the various minerals in the ore and produced sealable concentrates. Since measuring the mineral contents of the ore could be a demanding task one should consider to estimate this data from the daily chemical assays of the sample collected on the main streams of the circuit. Some authors have already investigated the problem. Whiten(2008) described a method to estimate the mineral contents of an ore sample. Lamberg and Vianna(2006) proposed a method to do a sequential mineral reconstruction followed by a material balance. Few of these methods account for the mass conservation of the reconstructed mineral contents."

Jan 1, 2016

By R. H. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

Jan 1, 2002

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8&apos;-3" wide by 9&apos;-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008