Search Documents

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By T. Gouri Charan

Indian coals, which are of Gondwana origin, contain high amounts of mineral matter, wherein the extraneous material was intimately mixed in the coal matrix during the formation stage, causing a high level of impurity in the run-of-mine (ROM) material. These coals possess difficult to very difficult washability characteristics. Beneficiation of high-ash non-coking coals of India has become the prerequisite for improving the overall economics and efficiency of power generation. The use of dry cleaning systems in India for beneficiation of non-coking coals has gaining renewed interest recently. The benefit of the dry beneficiation process is to exploit the given resources while providing a more reliable and consistent quality fuel with a low operating cost. M/S Allmineral has introduced a technique for the dry beneficiation of coal, which is being tried in India for the treatment of high-ash non-coking coals. The first commercial air jig of 50 t/hr capacity was installed and commissioned to beneficiate high-ash coals of 40 x 5 mm feed with an ash content of 40%; a clean coal product of 33% ash was produced and is being used for a sponge iron plant.

Jan 1, 2011

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By F. Chevarin

The reaction of O2 with the carbon anode is considered as the main parasitic chemical reaction affecting Hall-Heroult process anodes. The current study aims at investigating the influence of the microstructure of baked anode on its overconsumption. Samples were removed from different positions of an industrial anode. Density, porosity, Lc and BET specific surface area were measured. The anode reactivity was evaluated based on the weight losses for the samples resulting from the reaction of anode with air at 550°C after 7h. The essential parameters determined to control the air reactivity are closed porosity, Lc and pores with a pore entrance radius of 1.5, 8.5 and 12 p.m. The knowledge of effects of these parameters allows better understanding of the reactivity of anodes and consequently reduction of their overconsumption in electrolysis bath.

Jan 1, 2011

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By Aiden Carey, Jim Kennedy

During December 2007, Lake Cowal Gold Mine located in New South Wales, Australia experienced a significant pit wall failure. The wall failure resulted in the deposition of a large quantity of saprolite consisting largely of clays and lake bed sediments to the bottom of the Phase 1 open pit mine. This wall failure ultimately buried two loaded blast patterns.

Jan 1, 2011

By Kevan Ford, Getulio Junior, Rob Henderson, Wayne Philips, Chris Martin, Rob Thorpe

"Plant 2 at the Kinross Paracatu gold operation in Minas Gerais State, Brazil, was commissioned in late 2008. Designed to be the largest tonnage, lowest grade gold milling operation in the world, Plant 2’s throughput has steadily increased towards its design capacity of 5087 tons per hour.The plant employs a gold-specific flotation scheme to recover the majority of gold, which is present as discrete free gold particles. Additional gold is recovered by jigs in the grinding circuit, and the jig concentrates are reground, upgraded and subjected to intensive cyanide leaching. The flotation cleaner concentrate is reground and leached using a conventional CIL circuit.One year after start-up, with the plant stabilizing operationally, plant circuit surveys were completed by a joint team from Kinross Paracatu and Blue Coast Metallurgy Ltd. The surveys audited the flotation and concentrate treatment circuits to investigate the metallurgical performance.This paper describes the Plant 2 operation and how the surveys were designed and executed. Some of the quality control systems that were employed to provide meaningful data from such a low grade gold ore are described and findings and actions taken to improve metallurgy as a consequence of the surveys are discussed.INTRODUCTIONThe Paracatu mine is located two kilometres north of the city of Paracatu, in the north western portion of the state of Minas Gerais, Brazil, 230 km southeast of the national capital Brasília (shown in Figure 1). The present day Paracatu mining operation, fully owned by Kinross Gold, through its Brazilian subsidiary Rio Paracatu Mineração (RPM) is designed to be the largest tonnage, lowest grade free milling gold operation in the world.The deposit currently hosts some 1.2 billion tonnes of ore at a grade of ~0.41 g/t gold, hence contains a total gold reserve of over 20 million ounces. At a designed plant throughput rate of 61 Mt/year the mine life goes beyond 2030."

Jan 1, 2011

By X Dai

This paper investigated the loss of cyanide via oxidation in CIP or CIL processes by relating the cyanide oxidation to its major oxidation product, cyanate. The results showed that the oxidation of both free cyanide and copper cyanide complexes are substantially enhanced by the presence of carbon. The rate of cyanide oxidation was found to occur in the order: Cu(CN)32- > CN- > Cu(CN)2-. The cyanide oxidation rate in the presence of copper and carbon increased significantly with increasing dissolved oxygen concentration, typical of CIL vs. CIP conditions. Cyanide oxidation rate of iron, zinc or nickel cyanide complexes was minimal.

Jan 1, 2011

By E. S. Schubert

Keywords: co-generation, furnace CO-gas cleaning, disintegrator scrubber, Theisen In a closed, electric, reduction furnace, no oxygen enters the furnace from the surrounding environment. The off-gases are thus not ?burnt? and therefore contain a considerable amount of CO and H2. Traditionally these gases have been captured and burnt in a flare stack. Recent developments have led operators of such furnaces to revise this strategy and to consider utilising these gases as a fuel for gas-fired generator sets to produce electricity, thus becoming more energy efficient. On 31 March 2010 the new emission standards, in accordance with the Air Quality Act, Act 39 of 2004, were promulgated. The minimum emission standards according to the act require that the particulate matter emissions from the primary fume-capture systems on closed furnaces for ?new plants? in ferroalloy and calcium carbide production not exceed 50 mg/Nm³ and 25 mg/Nm³, respectively. By implementing co-generation, the producer automatically complies with the new environmental emission standards for an off-gas. As much as 30% of the electrical power cost, which is set to double in the near future, can be saved by partly generating one?s own electrical power. In December 2010, the National Treasury published a discussion paper for public comment, one entitled ?Reducing greenhouse gas emissions: The carbon tax option?. Irrespective of how the tax is finally implemented, it will result in an increase of production costs in affected industries. This paper focuses on the characteristics of a furnace-off-gas cleaning system for closed ferroalloy smelters, characteristics that meet the requirements of both reducing solid-matter emissions and operating a safe and reliable gas plant.

Jan 1, 2011

By Carrasco .. P. J. A., R. Parada, I. Saavedra, F. Parada, R. Parra, E. Balladares

In most of the smelters, the management of flue dust has a double objective: the control of minor elements in the anodes and the management of volatiles compounds that can cause contamination due to fugitive gas emissions. This is a special concern when high content of Va elements (As, Sb & Bi) are present in concentrates. We present the results of the experimental study to prove the principle of a novel process that recovers, via volatilization, the As, Sb and Bi in the flue dust as gaseous sulfides, due to a previous sulfidization. In the case of as control any further classical treatment for its stabilization is possible from the gas. The clean calcine can be returned to the smelter avoiding any concentration of these minor elements in the circuit. This process is now tested at pilot scale and shows better indices on carbon footprint than the classical hydrometallurgical process for flue dust.

Jan 1, 2011

By William D. Siapno

Mining the deep ocean by the year 2000 may seem far fetched. The year 2000 is but a decade away, a scant 10 years. Remember, the youngsters of today will grow up in a little more than a decade and rebut the wisdom of the ages, especially the traditions of their elders. Rude perhaps, but none the less a fact of life. Ocean mining exhibits many of these same traits. We should all brace ourselves for some rude shifts in our rapidly moving society. Major shifts in economics, politics, and social orders are the rule of the day. Communism is in retreat, our own economic structures chaotic. So in this moment of cataclysmic change, a shift in the international market place of mineral resources should not be a great surprise.

Jan 1, 2011

By K. Oraee

Zarshuran gold deposit, with the total reserves of some 12.5 million tons of 4.18 g/ton ore, is considered to be an important gold mining project in the area. In this paper the feasibility studies of the whole project is carried out on the basis of several economic variables. Given that mining data are often of uncertain nature, these economic variables have therefore been estimated under the conditions of uncertainty. The resultant Net Present Value is hence also obtained under the same conditions. For this purpose, a model is first devised with the help of Excel and COMFAR software. The model is then developed that considers different scenarios which would result in different expected values for the economic variables. It is concluded that the NPV of the project is most sensitive to gold and silver price and that other variables such as discount rate, operating and capital cost all affect the feasibility of the project with lower degree of severity. Finally, risk analysis is also carried out using Mont Carlo technique, in order to estimate the most probable value of NPV. The average NPV calculated in this way is US$ 49.7 Million, whilst without due consideration of risk, this would be US$ 36.6 Million. The techniques used, together with the procedures adopted in this paper, can be used in feasibility studies of all mining projects. Such decision would result in more accurate Net Present Values than expected from other frequently used methods.

Jan 1, 2011

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011