Search Documents

By Thomas Trochalides

Newtown Creek Water Pollution Control Plant in Brooklyn, NY is the largest of 14 Water Pollution Control Plants in New York City. It services over 1 million people with a current processing capacity of 310 million gallons daily. Upgrades to the plant have been underway since 1998. This paper details the foundation elements installed in three separate contracts during 2009: NC-41F, NC-36G, and NC-47G. The elements are Concrete-Filled Pipe Piles, H-Piles, Steel Sheet Piling, Secant Walls, Drilled Caissons, and High Capacity Micropiles. Soils on the site consist of fill over organic silty clay and silty sand. Beneath the organic layers lie lake sand and varved silt and clay, sitting atop glacial till and rock. Due to Federal Mandates, certain plant capacity and secondary treatment requirements had to be met by specific dates. Failure to meet the requirements would have an adverse affect on the NYC areas being serviced. Further complicating the project, the existing plant operations had to be maintained throughout the entire construction phase. To accommodate the constraints of the project, new specialty equipment and several key redesigns were used to maintain construction schedules

Jan 1, 2010

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.070 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70° C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 to 1,000 ms gave the following results: Ag concentrations decreased from 34 to 0.1µg/mL, Au concentrations decreased from 54 to 0.2 µg/mL, and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 2010

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By Jim Sadowski, Steve Stewart, Bob McMurdy, Martin Nevens

"Mohawk Garnet has been operating a small pilot plant near Sudbury, Ontario for several years attempting to produce commercially viable garnet. The challenges of operating a pilot scale mining, processing, and product handling operation as a full time plant have led Mohawk Garnet to seek a better way. In co-operation with Mohawk Garnet, Outotec (USA) Inc. has taken on the technical and design challenges of increasing garnet product from twenty tonnes per day to two hundred tonnes per day.Outotec performed a comprehensive test and flowsheet development program applying Outotec’s density separators, spirals, flotation, and other technologies to design a successful process for the separation and recovery of the valuable garnet for Mohawk.This paper explores the test program, the process flowsheet development work, plant design and preliminary engineering of a new garnet processing. The various technical challenges, process technologies involved, and design concepts will be discussed.INTRODUCTIONMohawk garnet has been operating a small-scale garnet mine and process plant in Wahnapitae, Ontario near Sudbury.The current operation was intended to be a pilot plant and so only produces 20-25 tonnes of garnet concentrate per day. The garnet is bagged and sold for use as abrasive. The process is inefficient with low yields, poor material handling and very high cost per tonne. Mohawk garnet approached Outotec to help them improve their garnet process and transform themselves into a larger scale and more efficient operation."

Jan 1, 2010

By Kaiser Gonçalves de Souza

Activities of Brazil in relation to deep seabed mineral resources development are carried out in the framework of two main national programmes. They are: (1) the Program for the Assessment of Mineral Resources of the Brazilian Continental Shelf (REMPLAC) and (2) the Programme for Prospecting and Exploration of Mineral Resources of the Area in the South Equatorial and Atlantic Ocean (PROAREA). REMPLAC aim to research and increase knowledge of the seabed and sub-soil, as well as to collect the necessary information to allow integrated management of the Brazilian Continental Shelf. Among the various research projects undertaken or planned on the framework of REMPLAC are: geology of the Brazilian continental shelf and adjacent ocean areas, organized in geological information system; digital bathymetric charts of the inner continental shelf at 1:100,000 scale; systematic research for sands, gravels, carbonates; placers, phosphorites, coal, cobalt-rich crusts, polymetallic sulphides and Gas hydrates. The PROAREA was prepared with three initial projects starting in 2010. One of them, the Project Geology of the South Atlantic and Equatorial organized in a Geographic Information System, aims to collect, collate, integrate and make available in a single environment all geo-referenced data and information available in Brazil and abroad on geology and mineral resources of the South Atlantic Ocean. The other two projects are for the research of cobalt-rich crust and polimetallic sulphides. These programme are developed with the participation of various segments of government agencies, research institutions and public enterprises. Marine scientific research and other activities from REMPLAC and PROAREA are carried out in partnership between the Geological Survey of Brazil, national research institutions from several Brazilian universities and the Directorate of Hydrography and Navigation from the Brazilian Navy.

Jan 1, 2010

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Seokbin Lim

In the design of explosives devices, an understanding of the behavior of explosively propelled matter is one of the most important steps in maximize the performance of these devices. For instance, an explosively driven metallic liner in LSCs (Linear Shaped Charges) creates its functional effect of penetration after a finite distance of travel (before collapse), thus the detailed study of the projection mechanism of the flat liner after detonation helps in the optimization of the design of LSCs. In a typical metallic flyer driven by explosive detonation, the detonation gas propels nearby matter including flat flyers. After a certain degree of expansion in the detonation gas, the flat flyer reaches its maximum velocity and slows down afterward. These typical behaviors are well investigated and numerically studied by many researchers. However, the rarefaction intrusion (detonation gas expansion) near the surface of the explosive charge creates significant deformation of the flat flyer , and produces U-shaped bending or deformation near the edge of the flyer during projection, creating unexpected behavior in explosive devices of interest. In this paper, a preliminary investigation of a localized Ushaped deformation of flat metallic flyers during projection is studied utilizing a theoretical approach and computational modeling facilitating an understanding of a general tendency of the deformation behavior.

Jan 1, 2010

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By D. M. Milovic

On the basis of relatively large number of field load tests of piles, the determination of the ultimate bearing capacity have been studied. Using the load settlement curves and the results of the cone or standard penetrat­ion tests, the ultimate bearing capacity was determined by Van der Veen?s, Mazurkiewicz?s and bilinear approximation method. Also, the evaluation of the modulus of deformation and the unit skin friction has been discussed.

Jan 1, 2010

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By L. Holappa

Ferroalloy production is an energy-intensive industrial sector with significant CO2 emissions. In this paper the current situation in ferroalloy processes is discussed from the standpoint of global environmental issues, trends and development. Progress and data of ferroalloys production are frequently compared with the steel industry, which is a closely related sector and the main user of ferroalloys. Emission factors of processes and electricity production are examined as well as possibilities and future scenarios of how to diminish CO2 emissions. As a part of this study a questionnaire was submitted to experts in the field of ferroalloys worldwide to survey opinions on the ferroalloy industry today and in the near future (2020). Eighteen questions concerning raw materials, energy, environmental aspects, by-products and economic aspects were responded to by seventeen experts, the answers were analysed and conclusions were drawn. Keywords Ferroalloys, energy, CO2 emissions, electricity, sustainability, questionnaire.

Jan 1, 2010

By J. Stacey

There are four components to this guideline 1. Guidance on the socio-economic aspects of closure policy 2. Socio-economic closure activities mapped against the mining project life-cycle (a ?check status? tool) 3. A process guide for mine closure planning and implementation 4. Tools in support of mine closure planning and implementation How to use this guideline The four components are part of a hierarchy with: ?Overarching policy as the starting point ?The mine life cycle model as a quick process check tool ?The process guide for detailed practical planning and implementation as practical guidance ?Supportive tools as resources to address specific planning and implementation steps.

Jan 1, 2010

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By Chris Castle

Following the recent award of a prospecting license by the New Zealand Government, Widespread Energy Ltd. (Widespread) is focused on the acceleration of its exploration program in order to bring a potential phosphorite deposit to market in the near future. Rock phosphate is the primary constituent of most fertilizers that are manufactured and distributed in New Zealand. Field trials in the 1980s demonstrated that direct application of rock phosphate can result in a more effective fertilizer (than super-phosphate) with less environmental damage from run-off. At present virtually all of the rock phosphate used by the New Zealand fertilizer industry (approximately 1 million tonnes a year) is imported from Morocco. In recent years price increases of up to 12 fold (peak of $500/t) with massive increases in freight costs have bought to the forefront the economic opportunity to in part replace foreign imports with a local source of phosphate. The Chatham Rise phosphate deposits are relatively well understood, having being discovered during the 1950?s and it is estimated that approximately 100 years supply (at current requirements) is present at shallow depths. An estimated 100 million tonnes of rock phosphate is present within the license area based on previous private and publicly funded research. Widespread has engaged several parties to assist in the exploration planning to confirm the resource potential. Widespread has commenced investigating the feasibility of recovering the phosphorite nodules off the sea floor, and presently has several conceptual technical solutions under consideration and will advance the discussions with potential contractors during the exploration phases. Widespread is acutely aware of its responsibilities to conduct both the exploration program and extraction of the rock phosphate, in a manner that causes minimal disruption to the marine environment. To this end, the National Institute of Water and Atmosphere (NIWA) ? a New Zealand Crown Research Institute has been engaged to assist in designing sampling and extraction methods that will minimize disruption to the seabed. All sampling and extraction activities are planned to be conducted with reference to the environmental guidelines published by the International Marine Minerals Society ?Code for Environmental Management of Marine Mining.? Widespread is conducting its project with a background of changing regimes to both the allocation and environmental management of its activities.

Jan 1, 2010

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010