Search Documents

By Y Chung, B Choi, H Lee

Numerous studies have explored refractory corrosion in the presence of slag and/or metal, utilising the Finger Rotating Test (FRT). Recent experimental results revealed that corrosion initially increased with rising rotation velocity but was then suppressed above a critical rotating speed, under conditions involving a two-liquid solution of slag and molten steel. This phenomenon indicated that the liquid/liquid interface movement occurred during spindle rotor. However, understanding of the phenomenon, known as the rod climbing effect, remains inadequate in the case involving slag, molten steel and refractories. To gain deeper insights, a simulation experiment was conducted on the phenomenon using silicon oil/water and the phenomenon was analysed using computerised simulation software (Ansys Fluent). Experimental modelling demonstrated that interfacial movement occurs even at low rotation velocity, as low as 200 rev/min, when the viscosity of silicone oil is at 100 cP. Computational analysis utilising the Volume of Fluid (VOF) method and a realisable k-ε turbulence model elucidated that interface elevation during rotor rotation arises due to viscosity disparities between the two fluids. Furthermore, this movement is more pronounced when the viscosity difference is lower. Additionally, the study findings suggest that higher density differences between two liquids suppress the phenomenon of interface movement.

Jun 19, 2024

By B Laidens, D Souza, W Bielefeldt

The CaO-MgO-SiO2-Al2O3 system, characterised by its intricate phases and thermodynamic properties, plays a pivotal role in steel secondary refining processes, encompassing desulfurisation, non-metallic inclusion capture, and refractory protection. Accurate predictions for diverse industrial applications, including metallurgy, ceramics, and materials science, are imperative. To address this challenge, a combination of machine learning techniques will be specifically applied to model the liquid fraction of the slag and the solid fraction of MgO. The development of an artificial intelligence (AI) system, leveraging various machine learning techniques, has gained momentum in this project. The focus of this work is on constructing an AI model, based on machine learning techniques, within the CaO-MgO-SiO2-Al2O3 system, utilising simulation results from FactSage™, version 8.1 (by GTT Technologies). The primary objective is to train the AI model using these simulation outputs to predict the percentage of liquid fraction and MgO saturation based on chemical composition parameters. The AI model will undergo training with a comprehensive data set of simulations within the CaOMgO- SiO2-Al2O3 system, covering a diverse range of compositional at 1873 K. These simulations, conducted through FactSage™ 8.1 software, provide a robust foundation for AI model training, ensuring generalisability and precise predictions for the liquid fraction of the slag and the solid fraction of MgO, the solid fraction of MgO in this case is determined by the difference between the total MgO and the MgO in the liquid fraction, so it is not the objective of this study to determine which phase of MgO is in the solid state.. The predictive capabilities of this AI model hold significant implications for process optimisation, quality control, and decision-making in CaO-MgO-SiO2-Al2O3- dependent industries. Precise estimations of the liquid fraction and MgO saturation empower researchers and engineers to enhance operational efficiency and quality. This paper explores the methodologies employed for AI model creation and training, achieved results in terms of prediction accuracy, and potential applications in the field. The development of this AI system signifies a notable advancement in utilising machine learning for better comprehension and control of complex chemical systems. Furthermore, to align the study with real-world steel production, we introduce FeO and MnO at concentrations of 2 per cent and 1 per cent at 1873 K, respectively, following the validation of model results using the CaO-MgO-SiO2-Al2O3 system. This adjustment aims to bring the study closer to the observed reality in steel mills globally.

Jun 19, 2024

By X Ling, M Barati, E Moosavi-Khoonsari

In the pyrometallurgical process of secondary lead recycling, a desulfurising agent, such as Na2CO3 is added to minimise the emissions of sulfur into the atmosphere, while silica is introduced into the smelter as a fluxing material. Subsequently, a significant amount of Na2O and SiO2 remains in the downstream reverberatory furnace and blast furnace slags. However, there is limited understanding of the thermodynamic behaviour of silicate-based lead slags rich in Na2O, posing challenges in accurately determining the optimal condition for targeted metal recovery and final slag composition. In this work, the equilibrium phase relations of the PbO-Na2O-SiO2 system in the primary phase field of Na2SiO3 are studied from 800 to 1000°C via equilibration-quenching method. Samples with different compositions were prepared and held in platinum capsules in air at these temperatures to reach equilibrium. The equilibrated samples were subsequently quenched and the phase compositions were measured by electron probe microanalysis (EPMA). The results were then compared to those of previous studies and any discrepancies were resolved.

Jun 19, 2024

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By J Nell, J Petersen, X C. Goso

The feasibility of increasing the deportment of titanium species and the stability of the pseudobrookite solid solution (M3O5) in a titaniferous slag was investigated, to facilitate the valourisation of titaniferous slags. Thermochemical simulations using FactSage™ software, ver 8.3 (by Thermofact/CRTC and GTT-Technologies), and equilibration-quench experiments were conducted using an appropriate synthetic titaniferous slag composition in an oxygen partial pressure (pO2) ranging from air to 10-16 atm under non-isothermal conditions. The temperature-pressure phase stability diagram for the synthetic slag containing 37.19 per cent TiO2, 19.69 per cent SiO2, 13.12 per cent Al2O3, 16.00 per cent CaO and 14.00 per cent MgO showed that the spinel solid solution (M3O4) was the primary phase until a pO2 of 10-10.5 atm, thereafter M3O5 was the primary phase until a pO2 10-13.2 atm. M3O4 again was the primary phase between a pO2 10-13.2 and 10-16 atm. The changeover of the primary phase coincided with an increase in the liquidus surface. When cooling the slag in a pO2 of 10-16 atm, M3O5 crystallised as a ternary phase that showed a rapid increase in mass while that of the primary M3O4 phase decreased and that of the secondary perovskite (CaTiO3) phase increased at a slower rate. At 1300°C under sub-liquidus conditions, the contents of M3O5, M3O4 and CaTiO3 were about 20 per cent, 15 per cent, and 11 per cent, respectively. Experimental results showed that the Ti3+/Ti4+ mass ratio in the M3O5 phase, ie a measure of the reduction of titanium species, is not considerably sensitive to equilibration temperature in the reviewed range. Slow cooling and minimum/no oxidation during cooling of titaniferous slag would increase the deportment of titanium species to, and the growth and stability of the M3O5 phase.

Jun 19, 2024

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024

By S van der Sluijs, M van Ende, Y Tang, A Emami

This paper presents a phenomena-based model for investigating the possibility of scrap melting in an Open Slag Bath Furnace (OSBF) for green ironmaking. The goal of this study is to enhance the circularity of the steelmaking process by utilising scrap as a green source of iron in OSBFs. The model takes into account the fundamental differences between OSBFs and traditional processes such as Electric Arc Furnaces (EAFs) and Basic Oxygen Furnaces (BOFs). The model considers three primary regions where scrap heating and melting occur: the solid feed pile, slag and hot metal. It accounts for factors such as the furnace geometry, scrap charging mechanism and specific heat and mass transfer properties of the reactor. The model was validated using literature data and was used to investigate the heating and melting behaviour of individual scrap particles under various process parameters. The study finds that the scrap melting process in OSBFs involves three stages: shell formation, shell remelting and subsequent melting of the parent scrap. The carbon content of the scrap and the liquid hot metal plays a critical role in determining the melting behaviour. Depending on the carbon concentration and temperature, the melting process can be heat transfer controlled or mass transfer controlled. The paper also examines the scrap feeding methods in OSBFs, including direct charging into the slag or charging through a feed pile. The model provides insights into the melting rate of scrap compared to Direct Reduced Iron (DRI) in OSBFs and highlights the role of carbon in this process. Overall, this phenomena-based model contributes to the understanding of scrap melting behaviour in OSBFs and provides valuable insights for optimising the circularity and efficiency of green ironmaking processes. The findings of this study can inform the design and operation of OSBFs, paving the way for increased utilisation of scrap as a sustainable feedstock in the steel industry.

Jun 19, 2024

By J Bang, I-H Jung

Ti is an important constituent for steels and superalloys. During the continuous casting process and ElectroSlag Remelting process (ESR), Ti in molten steel and superalloy can have chemical reactions with casting flux and ESR slag containing CaO and CaF2. In order to investigate such exchange reactions, the understanding of the (Ca,Ti//O,F) reciprocal slag system is prerequisite. In the present study, a coupled phase diagram experiment and thermodynamic modelling of the (Ca,Ti//O,F) reciprocal system was performed. In particular, the phase diagram of the CaF2-TiO2 system was experimentally investigated by Differential Thermal Analysis (DTA) experiment and quenching experiments followed by Electron Probe MicroAnalysis (EPMA) phase analysis. The Gibbs energy functions of all solid and liquid phases in the (Ca,Ti//O,F) reciprocal system were optimised to reproduce the present data and all available reliable experimental data in literature.

Jun 19, 2024

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By S Udayakumar, S Biswal, N Sarmadi, V Sahajwalla, F Pahlevani

Recent times have witnessed a notable momentum in the interest surrounding technology dedicated to harnessing waste as valuable resources, prompted by the mounting challenges posed by waste accumulation and the swift depletion of natural resources. The carbon dissolution process within a molten iron bath stands as a pivotal reaction within the metal processing sector. The current study explores the utilisation of waste graphite electrodes (WGE) (obtained after being utilised in an electric arc furnace) as a secondary resource of carbon for dissolution into liquid iron. Experimental investigations were carried out at 1550°C using the sessile drop approach. High purity iron powder was used and the carbonaceous substrates were prepared from the ground WGE. The carbon pickup was determined using a suitable carbon analyser. Furthermore, an examination of the interfacial area between the molten iron and the WGE substrate was conducted beneath the metallic droplet, which effectively represents the iron/carbon interface. This interfacial analysis was carried out on two different samples obtained after a varying period of heat treatments at 1550°C. The interface layer was investigated using scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDS).

Jun 19, 2024

By S K. Panda, M A. Van Ende, S Chatterjee

Tata Steel Netherlands (TSN) aims to reduce its CO2 emissions by 35–40 per cent by 2030 and become CO2 neutral by 2045. A first step to reach these targets is via the utilisation of an Electric Arc Furnace (EAF), which will run on a mixture of high proportion of Direct Reduced Iron (DRI) and scrap. For an EAF operation, optimisation of slag chemistry is important to achieve the right mix of basicity (for refining especially dephosphorisation), foaming, volume (rate) and refractory life. Slag composition and rate can vary widely depending on the process variables like charge mix, charge composition, feeding rate, oxygen lancing, external carbon injection/addition, fluxing and refractory erosion/corrosion. Moreover, it is important to note that the slag composition and rate are ‘transient’ parameters and change throughout the heat. This makes all the dependent phenomena and/or outcomes transient as well. To describe all these effects simultaneously and be able to realistically simulate the EAF operations, a validated dynamic process model is important in the absence of real plant data. In this study, a validated dynamic EAF process model based on the concept of Effective Equilibrium Reaction Zone (EERZ) has been utilised to analyse the impact of high DRI industrial scale EAF operations on the transient slag characteristics – including slag volume (rate), composition, phases, solid fraction and viscosity. Simultaneously, the model is able to predict the impact on steel and offgas characteristics. Case studies were performed with 70 per cent DRI:30 per cent scrap mix considering both low and high-grade DRI. Both melting and refining aspects of the process including continuous feeding, arcing program, carbon addition, fluxing and oxy-lancing were considered.

Jun 19, 2024

By F Tang, Ö K. Büyükuslu, M Baben, S Petersen

GTT-Technologies’ ChemApp for Python was developed to provide a powerful, easy to use interface to ChemApp for a programming language highly popular with scientists and engineers. It is used, for instance, by GTT to develop program modules such as the CALPHAD Optimiser for the FactSage™ software, by customers to move from interactive FactSage calculations to perform versatile scripting with Python, and by GTT and its partners in research projects in the area of materials informatics. Computational thermochemistry is fundamental for advancing sustainable metallurgy and creating new alloy compositions for engineering applications. Materials informatics involves handling vast amounts of data and complex workflows. GTT’s approach uses ChemApp for Python and the FactSage thermodynamic databases to design recyclable alloys from the start, incorporating a higher percentage of scraps while aiming to simplify the workflows to simulate material design steps. Challenges arise due to recycling scraps, introducing more elements for consideration. CALPHAD-based databases accurately cover materials from primary metallurgy, but additional data for minority and critical elements is crucial for precise computational modelling. GTT combines machine learning-based ab-initio databases with traditional CALPHAD databases to cover the complete chemical space with appropriate accuracy. The design of a hardfacing alloy through a high-throughput materials informatics approach is used as a demonstrator of the current possibilities.

Jun 19, 2024

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024

By K Vallo, T Haimi, J Pihlasalo, J Hamuyuni, M Lindgren, F Tesfaye

Decarbonisation of the steel industry has recently attracted a lot of research and technological development. Most of the technological developments are centred around the replacement of blast furnace (BF), which has been the main primary smelting furnace in the ironmaking step of steel production. Replacement of the BF is not an easy task because of BF’s many established capabilities over the years, especially its ability to use low-grade iron feed. In this regard, Metso has developed its own technology, Metso’s Outotec direct reduced iron (DRI) smelting furnace, to tackle this problem. The recently developed six-in line electric furnace for DRI smelting can be used for primary smelting of DRI from blast furnace grade iron ore. Unlike the electric arc furnace (EAF), the DRI smelting furnace can handle larger slag volumes that emanate from the high gangue in BF grade DRI. Therefore, fluxing plays an important role in operating the DRI smelting furnace. This paper presents fluxing options and proposes slag quality and operating windows for the DRI smelting furnace. Also, the effect of slag on refractory durability will be discussed.

Jun 19, 2024

By S Bright, M J. Masamvu, E K. Chiwandika, S Dandi, S M. Masuka

The depletion of high-grade hard and lumpy chrome ores has forced Zimbabwean ferrochrome producers to resort to low-grade friable ores that have an average of 28 per cent fines against a set limit of 12 per cent. Submerged open arc furnaces currently in use are associated with eruptions within the furnace because of the high amounts of fines, high energy consumption, as well as high SO2 and CO2 emissions. Traditionally employed agglomeration methods such as pelletising and the use of coke in the furnace have been discarded because of the pressure to lower operational costs and to achieve higher profit margins. This research aims to develop a method to incorporate lowgrade friable ore fines and unprocessed coal into production while lowering CO2 and SO2 emissions through a closed direct current (DC) arc furnace. The closed DC arc furnace could incorporate the friable ores and coal while maintaining above 90 per cent reduction rates. Preliminary findings also show that energy consumption could be reduced by up to 35 per cent by incorporating a pre-heating and pre-reduction system using the flue gases from the furnace. In the proposed circuit, the cost of production per ton of ferrochrome might be potentially lowered by an average of 30 per cent.

Jun 19, 2024

By I H. Jung, W O. Choe

Gallium (Ga)-containing compounds such as Gallium Arsenide (GaAs) and Gallium Nitride (GaN) are widely used in electronic devices due to their superior electro-optical properties and their usages increase rapidly. For the sustainable supply of Ga to electronic industry, therefore, the recycling of Gallium becomes essential. Pyrometallurgical Ga recycling process involves the complex chemical reactions between slag, matte, liquid metal, gas, refractories, etc. Therefore, the accurate thermodynamic information and phase diagram data for the oxide system containing Ga2O3 is important. In the present study, new phase diagram experiments for binary SiO2-Ga2O3 and ternary CaO-SiO2-Ga2O3 system are carried out using Differential Thermal Analysis (DTA) and quenching experiments followed by Electron Probe Micro-Analyser (EPMA) and X-Ray Diffraction (XRD) phase analysis. Based on new phase diagram data and available literature data, the thermodynamic modelling of the entire CaO-SiO2-Ga2O3 system is performed for the first time.

Jun 19, 2024

By J Safarian, D Hariswijaya

Treating bauxite residue as an alternative source of metals for iron and aluminium industry is an approach to promote circular economy in metal industries. Reduction of metal oxides with H2-based process is an important step on decarbonisation of metal industry. In this study bauxite residue pellets were prepared and were reduced with different H2-H2O gas compositions at different temperatures which yielded with various degrees of reduction. The bauxite residue pellets were made from a mixture of bauxite residue and Ca(OH)2 powders and sintered at 1150°C. Hydrogen reduction was carried out on the oxide pellets using a resistance furnace at elevated temperatures in controlled reduction atmosphere of H2-H2O gas mixtures which resulted in reduction of iron oxides in the pellets. Unreduced and reduced pellets were subsequently heated to 1400°C to study their smelting behaviour using differential thermal analysis (DTA) and thermogravimetric analysis (TGA) technique to investigate the evolution of phases related to slag formation via smelting. Equilibrium module of Factsage™ ver 8.1 was utilised to analyse results of thermal analysis. It was observed that Tricalcium phosphate-β (CaP2O8), Bredigite (Ca7Si4MgO16), Rankinite (Ca3Si2O7), and calcium alumino ferrite (Ca[Al,Fe]6O10) were formed during thermal analysis as intermediate phases. The initial slag formation for sintered and reduced pellets occurred at 900°C which mainly contains calcium and small amount of strontium component. The slag formation rate increases significantly starting from 1100°C when iron oxides started to form initial molten slag phase which then followed by other oxides dissolution in the system. Gas formation was observed at 1180°C and it was found that the gas to be released from unreduced pellets is O2 meanwhile the gas to be released from reduced pellets is SO2 gas. Gas formation rate for both pellets start to increase at 1280°C when the remaining chemically bonded gas start to be released from the system.

Jun 19, 2024

By H Kim, M J. Sun

In order to reduce carbon emissions from the steelmaking process and achieve carbon neutrality, global steel companies are establishing their own medium to long-term strategies and implementation plans using competitive technological advantages held by each steel company. At this point, Hyundai Steel has formulated a product-oriented carbon-neutral strategy based on innovative processing that makes use of Hyundai Steel’s own strength. Based on our experience in electric arc furnace product manufacturing and blast furnace operation in an integrated steel mill, Hyundai Steel is driving the Hy3 (Hy-cube) project, which involves a unique hybrid production system utilising hydrogen and hydrogen-based renewable energy sources. This initiative aims to achieve carbon-neutral production and eventually specialise in producing premium carbon-neutral automotive parts. The project has originality in that it involves not only designing processes using electric furnaces to produce premium steel products such as car body panels and electrical steel sheets, but also aims to reduce carbon emissions from the process, developing carbon-neutral products based on market demand. To assess the feasibility of the Hy3 project, Hyundai Steel conducted two pilot productions. The first pilot was producing a prototype of lower-arm part using electric arc furnace with three different kinds of raw materials: molten iron, HBI (hot briquetted iron), and scrap. Successful performance evaluation of auto parts with 1 GPa strength was achieved. The second pilot has been focused on tire cord steel, with the first-phase tests yielding a 33 per cent reduction in carbon footprint (CFP). Using the advantages of operating experience in electric arc furnace, Hyundai Steel is preparing for test operations producing various automotive parts using an electric arc furnace (EAF) to advance the Hy3 concept. From a medium to long-term technological development perspective, Hyundai Steel’s blueprint includes producing high-end carbon-neutral steel products using hydrogen-reduced iron as raw material.

Jun 19, 2024