Search Documents

By L M. van Niekerk

The mining of iron ore is a high volume low margin business because the value of this commodity is significantly lower than that of base metals. The main metallurgical challenges in most of the iron ore projects proposed for treatment nowadays have been in finding the optimum flowsheet for the treatment of magnetite ores, mixed magnetite-hematite ores and even ores that have banded ironstone formations (BIF). The associated plant designs incorporate very high capacity milling systems to grind the ore down prior to magnetic separation and in being highly capital intensive requires substantial investment in mega processing plants with associated infrastructure to mill down the run-of-mine ore to the desired treatment size for upgrading.To minimise the cost of infrastructure, better beneficiation techniques and technologies are being sought to assist in reducing upfront ROM feed to allow for reduction in overall treatment plant footprint necessary in extracting the desired downstream product. This paper discusses such beneficiation techniques and advancement in technologies for the upgrading of coarse and fine iron ore utilising dense media separation (DMS), jigging, wet magnetic separation, dry magnetic separation, flotation and x-ray processing.Another group of iron ore projects involve the mining of hematite ore below the water table. Often the mined ore is wet and sticky. This combination requires high capacity processing of feed material utilising large scrubbers or attritioning units to effectively remove the slimes component present in the feedstock. The fines removed, usually below 1 mm, are then discarded in large tailings storage facilities. Approaches to recovering the saleable material contained within these fines will also be investigated in this paper. This not only implies possible reduction in slimes discard footprint, but also holds potential benefit in augmenting overall yield and recovery of hematite product.CITATION:van Niekerk, L M, 2013. Fine and coarse iron ore beneficiation - An evaluation into global technologies and techniques, in Proceedings MetPlant 2013 , pp 584-598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By A Giblett, R Dunne, D Appelhans

There are a number of hurdles that must be negotiated in order to design an effective gold ore treatment facility such that the expectations forming the basis of project economics are valid and can be achieved in practice. Selecting samples based on geometallurgical context, performing and interpreting testwork relevant to the selected process flowsheet are essential considerations towards achieving this aim. This paper discusses recent experiences in process development for free milling gold ores giving consideration to frequently encountered challenges of this nature.CITATION:Giblett, A, Appelhans, D and Dunne, R, 2013. Considerations for effective gold process development, in Proceedings MetPlant 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By E J. Hofmann, J E. Hofmann, A J. Hofmann-Fritz

"With its Head Quarters in Perth, global heavy engineering company Hofmann Engineering is one of the largest family owned engineering companies in Australia. The company has pioneered a number of new manufacturing processes and design improvements for components of large comminution equipment.Some of these innovations are: Innovative design improvements of high pressure grinding roll (HPGR) forged steel tyres. Hofmann Engineering has developed unique patented tungsten carbide stud and edge protection designs which improve wear life and introduce quick and cost effective replacement options to further extend the life of the tyre. Development of forged fabricated mill heads using rolled and welded high tensile steel plate as an alternative to cast conical mill heads. Establishment of Australian capability to manufacture and export up to 42 ft. (12.8 m) diameter SAG mill shells. Techniques for fast track, product improved replacements of cracked or damaged mill gears, including in situ profile & wear measurements of girth gears using portable coordinate measuring machine (CMM) technology, forged rim steel and induction hardening technology. Gear and pinion mechanical drive designs to 24 MW or higher for SAG mills of 38 ft. to 42 ft. (11.6 m - 12.8 m) diameter as reliable alternatives to gearless drives.The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering on large, high powered equipment for both the domestic and export markets.CITATION:Hofmann, E J, Hofmann, J E and Hofmann-Fritz, A J, 2013. Australian innovations in high pressure grinding rolls and large grinding mill manufacture, in Proceedings MetPlant 2013, pp 141-151 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By M Kongas, K Saloheimo

Concentrating lower and more variable grade ore resources to meet acceptable concentrate quality criteria requires removal of significant amount of gangue minerals. Monitoring plant feed mineralogy and concentrate by on-stream analysis has significant economic benefits in concentrate quality and recovery optimisation. There is a need to develop a sensitive slurry on-line analyser for silica, aluminium, magnesium and other light elements.On-line XRF elemental analysis technology, which is a routine practice in base metal concentrators is not able to measure lighter elements than calcium from slurry. Too much of the X-ray fluorescence signal from lighter elements is absorbed by water. The limitations in the direct measurement of silica and other light elements have restricted its use in some applications. Some light element slurry analysers have been developed based on prompt gamma neutron activation (PGNAA) method but they have not performed up to the expectations. This paper describes a new on-line elemental slurry analyser and the results of on-line laboratory tests.CITATION:Kongas, M and Saloheimo, K, 2013. Online light element slurry analysis, in Proceedings MetPlant 2013 , pp 93-101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By G McMillan, P Mulvey

"Geochemical characterisation is done based upon the geology and metallurgical batch testing prior to commencement of the operation of the plant.  Tailings repository design is based upon geochemical assessment of the waste material, as well as the geomechanical issues associated with storing the waste. The resultant conceptual and detailed design is incorporated into the environmental impact statement (EIS), upon which mine approval is based. The entire environmental monitoring and harm mitigation program, which is usually a condition of the Mine Lease approval, is based upon the applicability of the original characterisation.Tacit to this process is that there is no change in the geochemistry of the tailings, i.e. no change in the implications for acid & metalliferous or saline/neutral mine drainage (AMD/SNMD) generation. But any changes in milling and processing can have a substantive impact on the geochemical behaviour of the tailings metallurgy, and potentially render an operation non-compliant within the conditions of the mine license.Environmental and statutory approval implications for continuous improvements of metallurgy need to be understood because unintended consequences could cost more than the benefits of the improvement, and in some cases cost more than all the profit made from the mine.  Examples uncovered during audit and consultant practice will be presented together with a process to ensure implications for adverse environmental harm and license conditions are fully considered.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Continuous improvement - how changes in metallurgy can have a substantive impact on environmental impact and closure - lessons learnt from environmental auditing, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By P Woodward, T Ly, N Muhamad

OZ Minerals' Prominent Hill copper-gold concentrator is located 650 km north-west of Adelaide in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a design capacity of 8 Mtpa. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell preceding the three stage conventional cell cleaner circuit.Since its commissioning, the Prominent Hill flotation circuit has been the focus of a series of projects aimed at continual performance improvement. This has been achieved by a systematic approach of project identification, evaluation and implementation which has led to a progressive improvement in flotation performance. Innovations that have been successfully implemented include aspects of cell design and operation, and reagent suite optimisation.Improvements to the mechanical cells initially focused on the installation of a modified rotor-stator design in the rougher circuit, as recommended by Outotec. Isolated cells were fitted with this technology and proven to provide a benefit for copper recovery before the design was trialled in subsequent cells along the bank. Based on this success, further modifications were made to other aspects of the rougher and cleaner cells.Laboratory trials conducted at Prominent Hill involve a screening process identifying potential reagents from a list of products, which are then rigorously tested in the laboratory before one is selected for trial in the concentrator. Where these reagents have demonstrated a statistical improvement in performance they have typically been incorporated permanently into the flotation circuit. This paper discusses the process of continual improvement at the Prominent Hill flotation circuit and the optimisation achieved by the implementation of key initiatives.CITATION:Woodward, P, Muhamad, N and Ly, T, 2013. Optimisation of the Prominent Hill flotation circuit, in Proceedings MetPlant 2013 , pp 431-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D Jensen, L Riffo, S Yu, F Traczyk, D Meadows

With the steady increase of molybdenum demand worldwide and the favorable molybdenum market, many technological innovations on both process and equipment have been developed and applied in many modern molybdenum plants around the world. This paper introduces the most commonly used molybdenum flotation flowsheet, together with the introduction of the flotation chemistry. Many different types of flotation cells are used in modern moly plants, and each type of flotation cell has its own unique advantages suited for particular ore and process conditions. This paper tries to provide some insight and guidelines in flowsheet development and flotation cell selection in the molybdenum plants.CITATION:Meadows, D, Jensen, D, Traczyk, F, Yu, S and Riffo, L, 2013. Molybdenum flotation circuit and flotation cells, in Proceedings MetPlant 2013 , pp 387-398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By T van der Meer, A Salokannel, M Martikainen, L M. Nevatalo, J McCulloch

Water use and wastewater management is becoming a focus for many industries around Australia and the rest of the world. Good quality water is increasingly being recognised as a precious resource, and regulations on the bulk storage and discharge of waste streams is becoming more stringent in order to protect the environment, existing water reserves and the communities that use these resources. Components such as heavy metals, arsenic, cyanide, and sulfate from acid mine drainage are some that occur at mining and metallurgical processing sites. Removal of such components can allow safe re-use of these streams, reducing the new water requirements of the process, or else allowing acceptable discharge to the environment. Re-use or discharge of treated water eliminates or reduces the risk associated with storage of large volumes of contaminated water on site.Technologies where a contaminant is selectively precipitated and removed as a sludge are used for many of these treatments. Selection of the best treatment option for wastewater must depend on what is suitable to each site, and consider not only the nature of the contaminant, but also other aspects, including the location and situation of the site, local regulations, cost of reagents, the sensitivity of the local environment and waste sludge disposal options. To outline how an effective and economical solution can be designed and delivered, this paper will present a case study for the removal of arsenic from a site wastewater, from assessment of the problem, selection of suitable technology, design and implementation, to the benefits delivered to the site.CITATION:Salokannel, A, Nevatalo, L M, Martikainen, M, van der Meer, T and McCulloch, J, 2013. Technology selection for removal of contaminants from an industrial wastewater, in Proceedings MetPlant 2013 , pp 531-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By C Barton, B Randall, T Weldon, M Lefler

FLSmidth-Summit Valley Technologies has been a leader in gold processing equipment for nearly two decades. Over the past several years an extensive research and development effort has led to improvements in Mercury Abatement systems and process efficiency in Adsorption Desorption and Regeneration (ADR) or "Carbon" plant operations. Two technologies will be discussed that are focused on efficiency improvements followed by an explanation of Mercury Abatement systems. Gold and silver can be desorbed from carbon in several ways. FLSmidth has made significant improvements to the Pressure ZADRA process allowing for lower energy consumption and lower capital costs. This patented process is known as the Split-ZADRA Strip method. Split-ZADRA allows a plant to elute loaded carbon in a semi-continuous fashion. This increases the grade of the Pregnant Strip Solution, improves electrowinning efficiency, reduces capital equipment costs, and reduces energy requirements. During desorption and electrowinning for the Pressure ZADRA process, the pressure and temperature of the circulating strip solution is changed multiple times. A self-contained heating and cooling system has been developed which decreases the energy requirements for elution. Mercury Abatement technology has become increasingly important in recent years. Along with FLSmidth Summit Valley Technologies' complete Mercury Retorting Systems, FLS-SVT has developed systems for the capture and removal of mercury from electrowinning cell and strip solution exhaust, Carbon Regeneration exhaust, and the dore furnace exhaust. This paper describes each of the technologies introduced above and their success in operational gold and silver mines. Case studies will be discussed showing the advantages of each specific technology as it applies to operations around the world. CITATION:Lefler, M, Weldon, T, Barton, C and Randall, B, 2013. Improvements in the mercury abatement and process efficiency of adsorption, desorption and regeneration gold processing operations, in Proceedings MetPlant 2013 , pp 468-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D van der Wal, R Dobbe, K Moeller

"Ore mineralogy and texture are primary variables controlling mill recovery efficiency in flotation plants. However, tracking daily variations of key mineralogical characteristics such as species-by-species liberation is not possible with current on stream analysers and assay lab techniques. In addition, traditional plant mineralogical analysis limited by long data turn-around times from central analysis laboratories typically provides only a time-averaged view of mill performance, e.g. by means of monthly composite feed, con or tailings analysis.This paper presents the results of a development and first field test of an on-site Automated Mineralogy solution (MLA or QEMSCAN) with the specific goal of monitoring recovery variation, ore quality and flotation performance on a mineral species-by-species and day-by-day basis, from up to twelve million direct particle observations per month. The trial was performed at a Pb/Zn-Ag operation in the US from November 2012 to April 2013. The focus of the study was three-fold: to validate the robustness of equipment and operational procedures for daily use by mine site technicians at a remote mine site to develop a methodology to boil down hundred-thousands of Automated Mineralogy particle data from size-by-size con and tailings samples to a couple of numbers meaningful to chief metallurgists to monitor recovery trend changes and correlate these to changes in the feed properties and/or flotation efficiency.The study focused primarily on the Pb/Ag rougher-concentrator circuit. Ten polished blocks of two and three size fractions of con and tailings were prepared by mine site technicians during a daily twelve hour shift. Eight hours of daily measurement time by the instrument revealed an estimate of the dayÆs recovery performance, ore quality and flotation performance for Freibergite (Ag-species) and Galena (Pb-species), within 36 hours from initial sampling. Data quality was assessed by means of calculated versus measured assay reconciliation. Cumulative sum curves of recovery performance, ore quality and flotation performance reveal trend changes with a frequency of 1 to 4 weeks. These were correlated to cumulative sum curves of e.g. locked and slimed particle classes of the mineral species of interest, attempting to identify a possible root cause of recovery performance trend changes. Systematic over-grinding and flotation chemistry issues were the primary causes of below average plant operations during the trial.CITATION:van der Wal, D, Dobbe, R and Moeller, K, 2013. Development of an on-site mineralogy solution for metallurgists, in Proceedings MetPlant 2013, pp 126-132 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By K Kermanshahi, J Allen, MáHilden, M Powell, S Mwansa, S Palaniandy

Approximately 420 VertiMills« (VTM) have been installed in mineral processing plants throughout the world, mainly in tertiary and regrind applications plus several in secondary grinding duties. Metso Minerals (Metso) and the Julius Kruttschnitt Mineral Research Centre (JKMRC) have commenced a collaborative research program in stirred milling technology focusing on mill performance evaluation, model development and scale-up methodology. Industrial VTMs are being assessed using a consistent circuit survey protocol to evaluate the performance of VTMs in comminution circuits. The survey protocol includes identification and modification of sampling points, appropriate sampling techniques, controlled circuit stability, and best sample analysis practice. To initiate this study four surveys were conducted in the tertiary grind circuit in the Ridgeway Concentrator at Cadia Valley Operations (CVO) that treats the full circuit throughput of over 800 tph. To deal with the high feed rate the site opted to lead the world in the application of stirred mills by installing the largest VTM, at 3000 hp (2240kW) in closed circuit with a hydrocyclone bank. On average the operating work index was 13.1 kWh/t, reducing the secondary grind product by 40 - 50 ¦m to the required 80 to 100 ¦m range. The applied specific energy is relatively low in these low-intensity stirred media mills at 2.7 kWh/t. The size specific energy was 24.2 kWh/t-75¦m. Based on the survey and operating data the VTM circuit is performing well in this high-throughput tertiary grinding application, producing a sub-100¦m product.CITATION:Palaniandy, S, Powell, M, Hilden, M, Kermanshahi, K, Allen, J and Mwansa, S, 2013. VertiMill« - Development of circuit survey and performance evaluation protocols, in Proceedings MetPlant 2013 , pp 162-175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J K. Claflin, S R. La Brooy

A case study from a current Ausenco project is presented to demonstrate the importance of maintaining high carbon activity to illustrate the driving force for plant improvements such as a carbon regeneration kiln upgrade.This paper revisits the factors that influence carbon activity for gold loading, with emphasis on deactivation by organic solution components such as flotation reagents.Kiln process design requirements for effective thermal regeneration are reviewed including the interaction of parameters such as temperature, kiln atmosphere and residence time.The different types of kilns that have been used for carbon reactivation are described. A check list is provided of what to look for when purchasing a carbon reactivation system for dealing with severely fouled carbon. This covers the ancillary equipment as well as the kiln itself.While the effectiveness of the carbon reactivation kiln is vital to maintenance of high carbon activity it needs to be remembered that this is only the end of pipe solution. It is also important to ensure that reagents such as frothers and flotation collectors are appropriately chosen to maximise recovery and at the same time minimise carbon deactivation.CITATION:La Brooy, S R and Claflin, J K, 2013. Carbon management in a high gold price environment, in Proceedings MetPlant 2013 , pp 455-467 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By P Moswate, D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of gangue mineral grade limits by the concentrator may also result in significant penalties.Online grade analysers which can provide reliable real time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and has the benefit of operating in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades.MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at the BCL nickel concentrator plant in Botswana. The project focused on stabilising the final concentrate grade while ensuring the final tailings are minimised, resulting in an improved nickel recovery. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser. The positive results show the advantages of combining reliable real time measurements with an advanced process control system.CITATION:Mantsho, S M, Moswate, P, Strobos, P and Phillpotts, D, 2013. The implementation of floatstar grade-recovery optimisation control solutions using Blue Cube Online grade analysers on industrial flotation circuits, in Proceedings MetPlant 2013 , pp 575-582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By L Lachance, F Flament, D Leroux, S GariTpy

"Considerable metal values are often locked in stockpiles (ore, concentrates, heap leach pads, slags, reverts, etc.) and process equipment (bins, holding tanks, thickeners, etc.). This is more than enough to justify accurate accounting of such in-process metal inventories from both financial accounting and operational perspective. However, accurately determining the metal inventory of an in-process unit is often a challenge in industrial practice. Audits have shown that available indirect or direct measurements often carry large inaccuracies. Sooner or later, ignoring these measurement errors lead to unexpected incoherencies in reported metal balances. In such situations, coherent metal balances are then achieved through subjective and sometimes significant adjustments of in-process inventory levels. While such metal accounting methods applied by mineral processing engineers used to be rarely challenged, they are now being increasingly scrutinised by various stakeholders. Hence, metal accounting procedures that mitigate subjectivity in adjustments while still coping with the unavoidable uncertainty are more relevant than ever.This paper reviews three different metal accounting methods for reporting in-process metal inventory values. Their individual application strongly depends on the available measurements i.e. The indirect method where the metal inventory of a given process unit is determined by subtracting the cumulative reclaim from the cumulative feed carries important flaws. The direct method also comes with challenging accuracy issues so that emptying a process unit is often the best available inventory measurement. This reality is recognised for by further analysing a previously proposed operating mode where two interchangeable process units are alternately used. The third investigated method is the redundant method which combines indirect and direct methods for a given process unit. This paper reveals that the dual process unit operating mode and the redundant method can both significantly improve the estimation quality of in-process metal inventories.CITATION:Lachance, L, GariTpy, S, Leroux, D and Flament, F, 2013. Review of metal accounting methods for in-process metal inventories, in Proceedings MetPlant 2013, pp 102-117 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By E Skinner, G Lane

Project delivery strategies are determined by project context, business case requirements, scale of project, market conditions, ownerÆs capability and preference, contractorÆs experience, resource and skill availability, project location and type of project or facility.Successful project management requires the setting of coherent, effective and realistic business objectives and success criteria. The management team needs to lead, prioritise, resource, align, plan, track and communicate the processes that enable the realisation of these business objectives and success criteria.For any given project there is a unique balance between selection of a simple project delivery strategy that minimises interfaces and a complex strategy that necessarily engages the use of expertise and experience from numerous parties. The right balance for a project between these "book-end cases" is a function of how the project owner or managing contractor defines its objectives and chooses to manage risk, cost, schedule and project quality, in the context of the conditions affecting the project.Selection of an effective project delivery strategy requires a detailed appreciation of the range of external and internal environmental / shaping factors which influence the project. These factors include the project constraints imposed by the business, market or operational environments and the selection of an effective mix of primary (head contract), secondary (mix of vertical and horizontal packages) and tertiary (type of individual contract) strategies. The selection of the primary, secondary and tertiary strategies also shapes the project, the size and responsibilities of the ownerÆs team and the framework for delivery of outcomes.How does an owner or prime contractor decide? What is the optimum for a given project? Those with operations management backgrounds will have different views to those with project and construction management backgrounds.Is the simplest practical approach the best approach? Each and every interface needs to be managed.The owner will want a very experienced team that is engaged directly with the owner. The team will have a track record of successfully performing projects using contractors skilled in their respective disciplines and selected using competitive tendering on brilliantly designed scopes of work and good contract terms, with a fully defined project scope and appropriate schedule, for which all significant risks have been addressed and no scope changes are outstanding. Budget and schedule will be expected to have been developed with a full understanding of the scope, situation, risk management requirements etc.The problem is that these conditions rarely exist. The challenge in selection of a project delivery strategy is to resolve how best to address the inadequacies between the ideal case and the present reality. The mechanism for addressing the inadequacies defines the likely outcome of the project.CITATION:Lane, G and Skinner, E, 2013. Project delivery, in Proceedings MetPlant 2013 , pp 50-65 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013