Search Documents

By Vitor Vianna de Castro Moreira, Danilson Gonçalves de Melo e Silva, Gabriel Augusto da Fonseca

The present work aims to describe the changes made in the operational procedure of the reheating shell furnace, of the hot-rolling of seamless tubes line at Barreiro Plant of VSB, during non-production periods, focusing on reducing natural gas consumption. According to the previous procedure, the furnace was kept at 750°C on these periods, using the main burners. With the new procedure, the furnace is naturally cooled, maintaining only the auxiliary burners with a pilot light turned on, without worrying about the conservation of temperature. Subsequently, the furnace is heated with a rate of 150 ºC/h until it reaches the setpoint temperature of production. This procedure change was successful and didn’t cause operational and security problems. The minimum stoppage time needed for the natural cooling to be economically favorable is 6 hours and 30 minutes. The new procedure reduced the natural gas consumption in 4.500 Nm³, considering 24 hours of stoppage, achieving an estimated annual economy on the thermal energy costs of R$440.000,00 in 2019.

Oct 3, 2019

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

In Potiguar West, in the regions of Vale do Açú, Mossoró, and Chapada do Apodi there are limestone outcrops of about 20 thousand square kilometers (with a thickness ranging from 50 to 400 meters). Limestone is an essential raw material for the manufacture of agricultural products and especially for construction. The rock serves for various productions, among them is used for the production of cement, lime, fertilizers, even ornamental rocks. Thus highlighting the mineral potential in the state of Rio Grande do Norte, as well as its use in the production of various products.

Oct 3, 2019

By Arnaldo Forgas Júnior

Three techniques for ferrite quantification were applied in a duplex stainless steel UNS S31803 solution treated at three different temperatures, 1000, 1100 and 1200°C, in order to verify their compliance with the results from ThermoCalc® prediction. It is verified that only austenite and ferrite phases are present in the samples and that an increasing in solution treatment temperature led to the increase of the volume fraction of ferrite. It is also observed that quantitative stereology technique shows absolute values closer to ThermoCalc® predictions. On the other hand, measurements by ferritoscope and XRD show significant deviations, probably due to texturing effect imposed by the rolling process.

Aug 16, 2017

By Luana Lessa Pacheco, Antônio Vitor Magalhães Cota

With the sharp fall in commodity prices, the terms cost reduction and higher productivity have become subjects that are constantly addressed in the daily life of companies, since these factors represent a question of survival of the organizations. To achieve this, the search for continuous improvement of our processes in order to guarantee space in the market is a reality and necessity, so it is important that companies know their processes in detail and have the maturity to make decisions based on data and facts. Thus, this work aims to apply the Six Sigma methodology to investigate which are the variables that most influence the transportation process, carried out by large trucks, increasing their specific consumption of diesel, which is the second largest expense of a company. mining in the city of Mariana MG. The goal of the project was to reduce diesel consumption in the large transport fleet by 7.4%, from 0.32 l / t (average carried out from Feb / 16 to Jan / 17) to 0.30 by February 2018 , with an estimated gain of R $ 4.2 million. The results achieved exceeded the established target, reaching a 10% reduction in specific diesel consumption, totaling a projected real gain of R $ 6.4 Million, in addition to the reduction of 1,710.52 t of CO2 in the atmosphere.

Oct 3, 2019

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By Luke A. Balzan

Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such realtime information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing a case study of their use at an Australian site, and a description of the potential benefits of a range of analysis equipment.

Aug 17, 2017

By Lindaura de Souza Cândido d’Ávila, Robert Nogueira de Azevedo, Itavahn Alves da Silva, Mariana Carvalho Araújo

The present study aims at the reduction of the dolomitic limestone by the addition of lime added with high MgO (magnesium oxide) content in the sintering process. To verify the feasibility of the use of additive lime as an alternative source of magnesium oxide, sintering tests were carried out at pot grate with different percentages of additive lime addition and with proportional reduction of the calcite lime dosage, evaluating the effects on the sintering process. The results showed that the additive lime is a good source of MgO for consumption in the sintering process of iron ore.

Oct 1, 2019

By Emerson Sena Balbino, Emylle Alves Leitão, Gabriel Arthur Guieiro, Lucas van Melis

The deployment of autonomous haulage system causes several impacts in mining production chain, being necessary an appropriate change management policy, crucial to observe and gather all the benefits brought by the technology. The change management is also necessary to guarantee the adaptability of the organization in the long term. This paper briefly presents the technology deployed in the autonomous trucks at Vale's iron ore Brucutu mine, the changes that the operation team faces in the adoption of autonomous technology and the required training path to develop new procedures to deal with the sensitivity of the autonomous haulage system, besides the new operational dynamics from a process point of view, with safer, more consistent and more productive operations.

Oct 3, 2019

By Hervé Thomasson

Siemens VAI has made an important Research & Development effort since 10 years on laser welder field. The last step of this program was in 2010, the evolution of its laser welder range by implementing the solid state technology with laser cutting and welding. Since this step, 8 welders were produced by Siemens VAI. Now after more than 1 year of industrial feedback, the results are showing a high level of performances on very demanding processing lines for a large range of products from Silicon steel to High Strength Steel with DP and TRIP grades. This laser welder concept using laser cutting and welding through solid state laser source is also proposed by Siemens VAI for pickling lines and tandem mills with significant advantages compared to standard solution.

Jul 30, 2018

By Johann-Paul Stemplinger

For lubrication of open gear drives applied in rotary furnaces, often gear greases are used as well as for lubrication of gear boxes in difficult sealing conditions. The selection of the gear grease influences strongly the wear behavior. Investigations with flow greases NLGI 00 were made in a back-to-back test rig determining the weight loss due to wear acc. to the standardised procedure ISO 14635 part 3. Different influences like base oil viscosity, thickener type and additional solid lubricant type were analysed. Only the type and amount of solid lubricant shows a significant influence on the weight loss due to wear. Finally, a linear wear coefficient clT according to the calculation method of the wear amount according to Plewe is derived and can be used to transfer the test results to any gears in practice.

Jul 31, 2018

By Leandro Seixas Bicalho, Raphael Alcantara da Costa, Pedro Martins de Almeida Rollo, Eduardo Tres, Anderson D. Thomazini

Usual pelletizing process requires the use of iron ore within a given range of particle size. The pelletizing plants often have comminution circuits composed of ball mills and roller presses to meet the granulometric parameters. Aiming at the partial removal of grinding operations and elimination of wet ore processing, the present study evaluated the pelletizing of two samples of ore with lower surface area: (1) sample with only one passage into the roller press (specific surface area of 997 cm²/g) and (2) “in natura” sample as fed to the pelletizing plant (specific surface area of 450 cm²/g). These experiments were conducted with the use of bentonite and the products E/PE MIN 070/19 and E/PE MIN 090/19, made available by Clariant for this purpose. The results indicated that conventional bentonite is not efficient for coarse particle agglomeration. On the other hand, the products E/PE MIN 070/19 and E/PE MIN 090/19 achieved good performance. Considering a sample with only one passage into the roller press it was possible to form pellets similar to those produced in the conventional process.

Oct 1, 2019

By Luis Henrique Torres Dantas, Maycon Athayde, Rossano Augusto Pilon Nunes

The objective of this work is to evaluate the physical quality achieved in the iron ore pellets and the temperature profile in the pellet bed by applying an inversion in the flow during the cooling. The firing of pellets requires a minimum residence time in the sintering temperatures of the hematite grains [1]. The applied concept aims at raising this time to pellets located at the bottom of the bed which would provide an improvement in the physical quality of the product. The tests were carried out in a pot-grate type oven and the samples of fired pellets were divided into three aliquots according to the loading position of the pot termed top, middle and bottom, the pellets were sieved and subjected to physical tests and the compared to conventional indurating flow with the same ores and inputs. It was possible to show an increase of 7 to 8% in the compressive strength of the medium and bottom layers, maintaining the top layer results. The objectives of the research were achieved and the tests will be extended to assess the impacts on the mass and energy balance of the indurating machine and its components.

Oct 1, 2019

By Paulo de Tarso Rossi Haddad, Eric Valmir Spósito, Cristiane Sales Gonçalves

The heat treatment is a process that acts as a key factor in the tool life of tools made with hot work tool steels. Due to their applications, the main desirable metallurgical properties of this material class are toughness and hot resistance, without which the tools may suffer premature failure, and may lead to increases in the cost of producing articles made using such tools [1, 2]. Therefore, special attention must be given to the heat treatments practiced in these steels, whose operations involve quenching and tempering. The present work carried out the effects of the austenitizing and tempering temperatures on the microstructural condition, hardness and impact properties of TENAX300IM®, modified AISI H11 with lower silicon content. Hardness was measured by the Rockwell method, C scale; the toughness was evaluated by the Charpy-V impact test; and the microstructure for each condition was evaluated by optic microscopy. It was shown that higher austenitization temperatures resulted in increased grain size and hardness; higher tempering temperatures resulted in reduction of hardness, and secondary hardening peaks were observed for some austenitization conditions. The impact resistance showed an inverse behavior to that of the hardness, remaining initially constant, up to ~ 550 ° C of tempering temperature, and then increasing with the tempering temperature. The microstructures presented great dissimilarity, mainly due to the dissolution of carbon and alloying elements in the matrix.

Nov 22, 2018

By Lucas Monteiro Corrêa e Lopes, Carolina Carvalho Nunes, Nathalia Luiza Nascimento de Carvalho

The characteristics of each ore make it impossible to predict the quality of a flotation concentrate without exploratory tests. The research begins with laboratory batch tests, and then, after advances in the determination of process conditions, the complexity of the tests increases in order to evaluate new parameters. The closed cycle test (LCT) simulate circuits with load recirculation and the greatest difficulty of this test is to stabilize the circuit and achieve equilibrium. Depending on mass availability, the types of tests that offer the highest reliability and informations about flotation in an ongoing process are mini-scale or pilot-scale tests. This work aimed to compare the results of the flotation tests in three scales (batch test, LCT and mini pilot) for the Bonsucesso ore, a new deposit, owned by Nexa Resources, that has sphalerite, zinc ore, and galena, lead ore. In the open flotation circuit of galena was obtained 27.57% content with 26.70% recovery, in the LCT test the content was 31.54% with 64.64% recovery and in the mini pilot reached 51.22 % content with 65.51% recovery. In the open sphalerite flotation the zinc content was 55.51% with 77.35% recovery, in the LCT test the zinc content was 56.71% with 84.42% of recovery and in the mini pilot of 50.02% content with 94.54% recovery.

Oct 3, 2019

By Márcia Maria da Silva Monteiro Pereira

Durante o lingotamento contínuo de aço, partículas de ZrO2 adicionadas na escória de molde facilitam a nucleação heterogênea de cristais devido à sua limitada solubilidade. A adição de ZrO2 promove a cristalização da fase cuspidina, o que auxilia na redução da transferência horizontal de calor no molde, amenizando desta forma o problema das trincas longitudinais. Outro benefício da adição de ZrO2 em pós fluxantes é reduzir a taxa de desgaste da válvula submersa (SEN) na interface metal/escória; a erosão da SEN é um problema sério. Através de testes de laboratório e de testes industriais concluiu-se que a adição de ZrO2 em pós fluxantes reduz a taxa de transferência de calor horizontal no molde durante o lingotamento contínuo de aço, considerando os dois tipos de pós fluxantes que foram analisados no presente trabalho. Além disso, observou-se que a adição de ZrO2 reduz a taxa de desgaste da válvula submersa na interface metal/escória.

Aug 16, 2017

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Amilton de Sousa Lins Junior

O presente trabalho faz parte de um amplo programa de pesquisas que envolvem o desenvolvimento de procedimentos de soldagem para componentes de sistemas de ancoragem de plataformas de petróleo. Particularmente, realiza-se um estudo das propriedades mecânicas de um metal de solda de alta resistência obtido pelo processo de soldagem GMAW para atendimento dos requisitos necessários para a soldagem de aços da classe IACS W22 Grau R4. Foram soldadas juntas multipasses pelo processo GMAW, com preaquecimento de 150°C, corrente contínua, posição plana e aporte térmico médio de 1,0 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal de solda depositado, tanto na condição de como soldado quanto após tratamento térmico pós-soldagem a 600°C por 1 hora. Os resultados mostraram que foi possível obter propriedades mecânicas que atendem os requisitos de aços da classe Grau R4 em todas as condições analisadas. Adicionalmente, verificou-se que o tratamento térmico pós-soldagem propiciou uma melhoria na tenacidade ao impacto devido ao revenimento da microestrutura do metal de solda.

Aug 8, 2018

By Carlos Magno de Lima Leonel

O presente trabalho teve como objetivo comparar o desempenho de processo entre espirais convencionais e espirais de grande diâmetro, na concentração de minérios de ferro. Foram realizadas campanhas de testes para levantar os dados necessários para comparar os dois modelos de espirais em estudo. Os resultados mostraram que as principais variáveis que afetaram a eficiência de separação nas espirais foram a abertura dos lemes e a concentração de sólidos na alimentação. A espiral de grande diâmetro obteve resultados melhores, mesmo sem a utilização de água de lavagem, porém mais testes serão necessários para uma conclusão definitiva.

Aug 16, 2017

By Emerson de Andrade Monteiro

As ligas de titânio ao Nióbio apresentam grande potencial de desenvolvimento graças a excelentes combinações de propriedades. O tratamento termomecânico a elas conferido é importante para atingir as propriedades desejadas. O presente estudo tem como objetivo avaliar o efeito da conformação mecânica nas propriedades da liga Ti42Nb forjada a frio com 80% de encruamento e seguido de envelhecimento. Foram realizados ensaios de tração, medidas de dureza, metalografia e microscopia das superfícies de fratura. Foi possível observar que a liga Ti42Nb apresentou maior dureza e consequentemente maior resistência após o envelhecimento.

Aug 16, 2017

By Rafael Lioji Kogake

O Alto Forno n° 2 é responsável por cerca de 40% da produção de gusa na CSN. Uma das principais utilidades responsável pela transformação do minério de ferro em gusa é o ar soprado que é fornecido por dois turbo sopradores da Central Termoelétrica n°2. Para que ocorra o processo de transformação do minério é necessário que o ar soprado seja aquecido. Isto é feito através dos regeneradores, os quais aquecem o ar para cerca de 1.300°C. Como cada regenerador tem um tempo de campanha, é necessário fazer a troca do mesmo a cada 1 hora. Nesse momento de mudança de regenerador, uma parte do ar soprado é desviado para o regenerador que está entrando em operação e ainda está vazio. Com isso, há uma perda pontual de produção indesejada, além de causar instabilidade no processo. A solução encontrada para reduzir este problema foi aumentar a vazão de sopro durante o período de troca de regeneradores, garantindo assim uma maior produção e melhor estabilidade do Alto Forno 2. Este trabalho apresenta o estudo do problema em questão, a metodologia utilizada para a sua implementação e os resultados alcançados.

Jul 31, 2018