Search Documents

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017

By Andrea Donadon

This article introduces the Danieli Total Asset Management System, which involves 360 degrees service methods and equipment. Danieli Condition Monitoring System and Danieli Torque Monitoring System are fundamental to evaluate the conditions of the working components in heavy duty transmissions. The first one monitors the vibrations and the lubrication fluid conditions with the purpose to identify the presence of malfunctions, by detecting any variation of the signals from the standard values. The second one monitors the transmitted torque for each spindle and gearbox, with the aim of detecting any anomaly in torque distribution and magnitude, and evaluating the residual life of the mechanical parts, on the base of a dedicated fatigue damage algorithm. All these features are useful in avoiding serious damages to machines, facilities and people, but allow also planning the maintenance and overhaul activities with efficiency, in order to achieve the best plant availability and reliability. The data analysis is made by the IntelliCMS software, which interfaces with plant and Danieli operators and includes the possibility to cooperate by remote connections, simplifying service activities and support. All these features allow providing new full service programs, where the client is totally supported in maintenance, overhauls and substitutions. This is the best way to ensure the most efficient, high quality and reliable after sales assistance.

Aug 16, 2017

By Carlos Martins de Oliveira

The trucking industry is constantly seeking improvement and cost reduction of their vehicles, studying new lighter and robust materials to meet the needs of its customers. The objective of this work is to study the application of DCPD Telene, PU. R. RIM and PP-TD 20 materials in aesthetic components of trucks: bumper, calender, upper and lower bracket and side air deflector. A multifunctional work team was created to work in such parts of IVECO trucks. The work began with an analysis of possible improvements to the current parts and followed the subsequent phases: definition of new materials, virtual modeling, new tools, and durability test in vehicles. It could then be verified that the proposed DCPD Telene, PUR. RIM and PP-TD 20 materials showed greater strength, better painting surface, and reduced weight and cost in parts.

Aug 8, 2018

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Rainer Fackert

3D-Measurements for slabs and heavy plate are now available and close the gap in the production chain. The measuring systems described in this presentation must be seen as high-tech solutions in the field of casting and rolling technology. The measuring systems were developed taking into consideration the harsh casting and rolling mill environment in which they are to be used, with the aim of achieving high operational reliability and eliminating disturbances. Interconnected quality management systems enable optimization across the complete production process. New limits are being defined constantly for all these developments. What is technically feasible today becomes normal practice tomorrow, and will probably be replaced by completely new technologies the day after.

Aug 16, 2017

By Armando Vazquez

When water enters the EAF, some chemically dissociates to H2 while some remains as H2O vapor. Depending on operating conditions the levels of combustible gases (CO and H2) and H2O are continually changing throughout the course of any individual heat and on a heat-toheat basis. The EFSOP® system has been implemented in more than 80 installations as a powerful tool to reduce furnace operation costs but with water detection technology the off gas technology is a valuable solution to improve safety. This paper describes the latest results when using Tenova Goodfellow’s new standalone water detection technology that for the first time provides real-time analysis of both H2O vapor and H2 from start-to-end of a heat. It involves a newly designed water cooled probe and heated line that eliminates condensation during off-gas sampling and an analyzer equipped with a proprietary system for analyzing both H2O vapor and H2.

Jul 30, 2018

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By Hirohide Kamada, Gustavo Scarpim

The increase in industrial demand is responsible for a consequent evolution in the process of injection of aluminum under pressure (Die Casting) to achieve requirements such as; greater geometric complexity of injected parts, larger dimensions, hard-filled cavities, thin walls, and more refined mechanical and aesthetic requirements. Thus, the industries have searched for sensible increases in pressure and injection speed, always combining the best resistance and performance of the wells submitted to the new process conditions. The need for more aggressive applications for the cavities means that there is a constant evolution of the entire production chain in the manufacture of molds, passing through several processes, among them; machining, designs with complex engineering solutions, refining in the process of heat treatments and surface treatments. Allied to these needs, high performance steels manufactured by differentiated processes with high fracture resistance, hot strength and wear must be selected. This work aims to present the main factors considered in the development of high performance molds, the engineering of materials involved, technological trends and technical engineering solutions for the different variables of the die casting process.

Nov 22, 2018

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Ivo Filipovic

The steel melting process in an Electric Arc Furnace is a complex set of tasks, coping with highly dangerous hazards as fire, explosions, uncontrolled reactions, hot metal projections and gas or dust emissions. Melt shops are dangerous working areas for operators, recording statistics with a high frequency of injuries. In the past years, without dedicated safety equipment, there wasn't a real attitude to the risk prevention. The paper describes the available technological packages to eliminate the manned activities on the melting floor, with the aim to prevent accidents and keep furnace operators safe. The technological packages suite extends the automatic control of the EAF melting process to all the operations from charging phase to tapping. Plus, the integration of the most frequent operations by automated specialized tools effectively minimizes power-off times, enhancing reliability and improving the transformation costs.

Aug 17, 2017

By Jean-Paul Simoes

The development of the blast furnace over the last years lead to a substantial increase in production capacity and productivity. This development triggered an evolution of the cooling systems in order to cope with the raising heat loads. The excellent protection of the shell by copper staves allowed blast furnace operators to achieve campaign lifetimes of more than 20 years. However in recent years some blast furnaces have experienced severe wear of the copper staves due to abrasion. The influences of the blast furnace design as well as of the operation conditions on this premature wear have been analysed and the mechanisms leading to the wear will be explained. New developments in the copper stave technology are part of the solution for avoiding premature wear during periods with less favourable conditions. The protection mechanisms made available by the new design extend the inherent protection mechanisms of copper staves to these periods. BFXpert® system is the ideal tool for the monitoring of the process data, the process models and the recommendations given by Sachem® support the operator in choosing efficient operation points. The charging with a Bell Less Top® (BLT) allows an accurate controlling of the blast furnace with regard to the optimization of the gas distribution. High performance operation together with long campaign lifetimes are thus made possible.

Aug 1, 2018

By Pietro Palma

Universal cardan joints are widely used in drivetrains of rolling mills for steel and aluminum making, as well as for non ferrous alloy industry. Working conditions are extremely tough due to high alternating or pulsating rolling torques in the roughing stands and high torques and speeds in the finishing stands. Overloads and lubrication along with oxide and slag are also critical issues that contribute to create severe working conditions. For a constant and reliable power transmission rolling mills performance and uptime rely on Universal cardan Joints which are the most critical equipment of the drivetrain. Fatigue assessment of the most important components of the Universal cardan Joint is therefore definitely vital for the mill in order to avoid failures and consequently downtimes. Considering the component’s dimensions and weight and in addition the time needed in order to reproduce full scale tests, a new approach to study the Universal cardan joint’s main components fatigue behavior has been investigated. It consists in reproducing the local stress condition of the main joint components on small scale specimens that can be tested by conventional laboratory fatigue machines. The aim of this study is to analyze the most critical stress concentration areas in the universal cardan joints highlighting how a universal cardan joint Wöhler curve can be determined through laboratory tests of small scale specimens.

Aug 16, 2017

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By Afshin Sadri

One of the main reasons for blast furnace reline is the loss of refractory lining, particularly in the hearth and taphole regions. Intense operation of the blast furnace can result in extensive refractory wear and deterioration. This can then affect the continuity of the operation and the furnace campaign life. Novo-Lipetsk (NLMK) and Hatch developed a systematic approach to monitor the condition of blast furnace hearth linings using Acousto Ultrasonic-Echo (AU-E), a non-destructive testing system developed by Hatch. Continuous and periodic inspections of blast furnaces revealed areas with accelerated refractory deterioration, formation of elephant foot, extent and speed of refractory wear, as well as cracks and other anomalies. Improvement in coke quality, stave washing, the addition of titania, and other changes were recommended and implemented to prolong furnace life while maintaining the intensity of furnace operation. This paper demonstrates how the coordinated efforts between NLMK and Hatch resulted in prolonging the blast furnace campaign life.

Aug 17, 2017

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Emanuelle Garcia Reis, Gustavo de Sousa, Rodney Pardo Alves

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. In general, national and international plate markets are every day more rigorous about final product quality. Suppliers must be aware about dimensional accuracy, surface quality and flatness of the plates, independent of the quality standards. To guarantee the best service to this increasingly demanding and competitive market, it is extremely important to guarantee the original project conditions executing the right maintenance of the rolling mill main components. In order to maintain the product quality and avoid the production and maintenance cost increase, it is important to find ways to control the mill and the main process variables, through daily measurements of the equipment performance. This paper aims to present the influence of the main equipment variables that affect the mill operational stability and how to control and evaluate the mill performance.

Oct 1, 2019

By Franco Gandin

With increasing demands for highly performing and at the same time efficient and running-costs saving vacuum-degassing equipment, dry mechanical pumps have been confirmed a proper choice to completely fulfill the expectations of steel-making companies worldwide. Regarding the production of both special carbon steel and stainless steel grades, the usage of mentioned pumps allowed reaching simultaneous remarkable results from different viewpoints in various Danieli worldwide installations (treating up to 200 t of liquid steel). As a matter of fact, in front of the replacement of a widely spread and renowned technology such as steamejector pumps with the recently developed technology embodied by the dry mechanical pumps, well-established metallurgical performances in terms of carbonhydrogen- nitrogen-sulphur removal have been repeatedly attained while meeting at the same time the client’s expectations concerning, for example, running-costs and push-button availability. Additionally, thanks to the very flexible, modular, redundant and maintenance-friendly equipment design, random problems occurring to the singular mechanical pumps can be easily solved without affecting the VD-VOD plant availability and metallurgical performance. With a particular regard to the VOD process, a very short overall process-time has been repeatedly performed (averagely less than 58min under-vacuum time at ChMP1) while guaranteeing the expected required quality of the final refined stainless steel. Moreover, in several VOD installations (ranging from 6 t up to 110 t of liquid steel) an efficient automatic process control such as dynamic pressure-regulation during oxygen-blowing has been attained thanks to the controllable variable-speed drives with which each mechanical pump is provided.

Aug 17, 2017

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017