Search Documents

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017

By André de Cabral Oliveira

With the onset of the global economic crisis in 2008, and more precisely from 2009, production routes in iron making as blast furnace, sinter and coke oven, indicated a significant increase in frequency as well as intensity of undesirable incidents. The cost impact of such deteriorations of the production chain cause significant losses ranging up to several hundred million dollars annually. On the other hand, opportunities for processes improvement are contributing to enhance process efficiency and results, and also reduce or even avoid losses from unexpected incidents. The use of specialized services for processes has gained projection along the plants and emerged as an attractive alternative to increase results by increasing the performance and reducing costs and expenses. Process Services are formatted to achieve cooperative and customized solution during planned or urgent interventions, conducting feasibility studies, process improvement, training, among others, providing knowledge, information and crucial actions to preserve and optimize processes and plant facilities.

Aug 2, 2018

By Detlef Ehlert

In view of the increasing level of cost pressure on the part of plant owners, optimized plant operation with top product quality and maintenance costs is indispensable. Unscheduled shutdowns with increased repair costs and production downtimes are significantly reduced by preventive maintenance and the stock-keeping of spare parts. To remain competitive in the steel market, it is important for plants owners to operate their plants with the highest possible degree of energy efficiency and at high availability in order to manufacture high-quality products. Plant Monitoring Systems make it possible to optimize the manner of production. An integrated overview of the overall process, under consideration of process stability, product quality, production costs and plant availability ensures a “transparent plant”.

Aug 16, 2017

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Vitor Guarnier Domiciano

The need to adjust the monolithic refractories to increasingly severe and unstable Blast Furnace casthouse operating conditions has been a major challenge for refractory suppliers in order to guarantee the runner’s safety and its availability for operation. This paper presents the properties of a new robust single line Al2O3-SiC-C refractory castable developed to endure the severe operating conditions that main runners are facing in today's Blast Furnace casthouse scenario. Practical results during almost one year of testing revealed a significant lower wear speed of the new refractory lining when compared to a standard product.

Aug 1, 2018

By Felipe Poffo, Flávio Messas

Due to the high level of competition in tooling sector, a necessity to increase the level of processes and assets management has initiated. Based on the World Class Manufacturing methodology, applied mainly in serial production industries, we have challenged ourselves to adapt the main concepts and implement them in a tooling company. After one work year, we could notice 29% productivity improvement in the bottleneck process, 25% cost reduction in outsourcing, standardization of the processes, 8% reduction in direct labor. Consequently, it was possible to implement a financial reserve and a long term planning cash flow.

Nov 22, 2018

By Stanislas Mauuary

Price pressure is a real challenge on the stainless steel market. With market globalization, increase production capacity and exorbitant raw material, the margins are squeezing for stainless strip producers. Primetals Technologies offers a wide range of advanced technological solutions to secure the margins of our customers. Our solutions, implemented with professional project management, allow an optimum coil to market time, securing then the return on investment for the investor. Among the possible lever used to optimize the production route, one drastic step can be made to cut rolling time and cost by replacing the common 20-Hi mill stand reversing process by state of art high capacity X-HI® stands in continuous rolling line. Other source of savings can be implemented by integrated several process steps together (rolling, annealing, pickling, skin passing), achieving then savings on stocks and logistics while coil processing is reduced to fraction of hour. Additional solutions can also be implemented on the new, as well as existing line, like maintenance free solid state laser welder, skin-pass and tension levelers, in-line inspection system coupled with process and quality management system.

Aug 17, 2017

By Karl Berger, Michael Steinkogler

The evolution in Metal Cutting: Inventors around the world have been successfully developing innovations for decades, but only some of these developments have had „GAME CHANGING“ potential. One of these innovations is the new developed saw blade LINCUT®, a patented changing system that paves the way for a fundamental reorientation of the entire saw blade industry worldwide through a simple and economical concept for rolling mills or heavy forging lines. Cost efficiency starts with the raw material: Circular saws equipped with a standard saw blade are expected to have a necessary 2 percent standstill per year due to required tool changing. The applied technology reduces this unnecessary loss of production by more than 50%. The ROI can therefore be reached faster which immediately lowers your production costs. No matter what material, conventional carbon steel or highly alloyed stainless steel, the coating and shape of carbide plates is perfected for extended tool life up to 25% with increased performance. Due to LINSINGERs own tool-technology-centre in Austria specialized in research and development of tools, constantly expanding R&D activities, best results are achieved in quality and cost efficiency: a (r)evolution in metal cutting.

Oct 1, 2019

By Stephanie L. Kaster, John G. Speer, Blake M. Whitley

Niobium-microalloying technology has been increasingly applied in a wide range of steel applications over the past half-century, to increase strength, control microstructure, enhance properties and enable a variety of applications. To achieve desired performance levels, thermomechanically processed microalloyed steels are widely supplied by the steel industry for high volume applications in hot-rolled plate, sheet and structural steels. However, in steel long products and forgings, the final properties are often generated by downstream users, after heat-treatment, surface hardening, forging or wire drawing. Two examples are presented highlighting advancements associated with Nb-microalloying, to enhance microstructures and properties developed during thermomechanical and/or downstream processing. In the first example, a 0.02 wt. pct. Nb addition was made to a medium-carbon bar steel intended for induction-hardening applications requiring fatigue and fracture resistance in bending and torsion. The Nb addition as well as thermomechanical bar processing led to beneficial refinement of both the pre-induction and post-induction microstructures. In the second example, a 0.01 wt. pct. Nb addition to a high-carbon wire rod was found to refine the pearlite colony size and interlamellar spacing, and increase the hardness.

Oct 1, 2019

By Georg Keintzel

The origin and elimination of 3rd octave mill chatter is a frequently investigated topic since tandem cold mills are in operation. So far only chatter monitoring systems have been successfully deployed, but this implies speed reductions and therefore a significant loss in mill output. Primetals Technologies has developed a new system using active injection of damping in order to eliminate 3rd octave mill chatter. The new hydraulics-based ChatterBlock® Control has now been proven successfully in mill operation. 3rd octave mill chatter, typically occurring in a frequency range between 90 and 150Hz, is a self-excited vibration phenomena typically occurring in the rear stands of tandem cold mills. It can produce significant gauge variations and even cause strip breaks. 3rd octave mill chatter is characterized by a quickly diverging vertical vibration of the rolls for specific rolling conditions (material, mill speed, forces, gauge etc.). Its occurrence requires immediate speed reduction of the mill in order to avoid strip breakage and/or strip quality degradation. This phenomenon thus severely limits mill productivity. The first step to proof the industrial feasibility of the new system was its installation on stand no. 4 of a 5-stand tandem mill. The development process and first results of the industrial implementation will be presented in this paper.

Aug 16, 2017

By Fernando Hernández Polanco

Transportation and handling metals and alloys from mills to consumption factories as well as dosing in conventional processes with ingots and scrap has always been considered a complicated activity with high operating costs. Several manufacturers of ferroalloys willing to solve these problems have chosen an alternative for their products that can be used to secure, during transport and dosage in the processes to making special steels, with more efficient consumption of ferroalloys. The trend for the production and sale of ferroalloys is to provide the product in the form of granules packed in bags or in bulk. In this paper we will show you how the granulation process was developed and rapidly adopted the ferroalloys industry as an effective solution to reduce operating costs, create cleaner and safer working environments.

Oct 30, 2017

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Arnaldo Forgas Júnior

Three techniques for ferrite quantification were applied in a duplex stainless steel UNS S31803 solution treated at three different temperatures, 1000, 1100 and 1200°C, in order to verify their compliance with the results from ThermoCalc® prediction. It is verified that only austenite and ferrite phases are present in the samples and that an increasing in solution treatment temperature led to the increase of the volume fraction of ferrite. It is also observed that quantitative stereology technique shows absolute values closer to ThermoCalc® predictions. On the other hand, measurements by ferritoscope and XRD show significant deviations, probably due to texturing effect imposed by the rolling process.

Aug 16, 2017

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By Bernardo Siqueira

This paper presents a unique stirred milling technology, Outotec HIGmill™, a modern, flexible and energy efficient grinding solution for fine and ultra fine grinding being tested in an industrial scale level. The test was performed at an iron ore pellet producing plant in Sweden (for confidentiality reasons, it will be referred to only as “the client”) where a pilot HIGmill™ unit (HIG25) was installed parallel to a conventional regrind circuit to compare its performance to the existing ball mill. By using a continuous test run procedure and evaluating the parameters of F80, P80, mill shaft rotation speed and power drawn it was determined its grinding capabilities, operational flexibility and energy efficiency. Outotec HIGmill™ outperformed the existing ball mill in the plant proving its capabilities to grinding finer, with steeper particle size distribution (PSD) and much higher energy efficiency. The tests performed showed that, with further refining of its operation, it is capable of consistently deliver the required PSD with up to 30% higher grinding efficiency.

Aug 16, 2017

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019