Search Documents

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Detlef Ehlert

Flexibility in terms of producing high sophisticated products with an exceptional wide range of properties and dimensions requires physical based process models for the generation of optimal set points. Therefore SMS applies since many years an integrated PSC® (pass schedule model), PCFC® (profile, contour and flatness model) and CSC (cooling section control) for the use in hot strip mills, CSP® plants and plate mills offering best possible product tolerances. Focus during the development of the model was made on the best possible physical description of the rolling process to minimize the need of complex adaptation algorithms. As an addition SMS has also developed a microstructure model to ensure the quality control with respect to mechanical properties and to save up the needs of taking samples. Beside of this the modular design of the Microstructure and Material Property Model (MPM) offers additional benefits to improve the accuracy of the other models, e. g. the recrystallization model in the finishing mill. Using the results of that model strain hardening or softening effects during rolling can be predicted and an optimum pass schedule can be calculated to avoid rolling stability problems related to phase transformation.

Aug 16, 2017

By Norbert Asamer

At various stages during the hot rolling process, the different rolled products – blooms, billets, bars, respectively sections, but also slabs or plates – need to be cut. While the cross sections of these products are being reduced during each rolling pass, the lengths are being increased accordingly. Thus, it becomes necessary to cut the products to shorter lengths suitable for the next steps of production by state-of-the-art designed dry abrasive cut-off machines.

Jul 30, 2018

By Paul Pugsley

The need for dimensional measurement of products has always been there, now with the industry 4 push to further understand measure and to record process parameters is more important than ever. This applies to both flat and long products, camera systems have always provided the method to measure, stereo Linescan cameras for flat products and innovative applications using 2D and Linescan cameras for long products. Instrumentation will become more important to producers enabling processes to be better controlled and understood, that aim being to make the production process understandable more repeatable and less reliant on operator influence. Primetals Technologies Ltd offer solutions for all types of products.

Oct 30, 2017

By Jan Bak

Rourkela Steel Plant (RSP), which is operated by the Steel Authority of India Limited (SAIL), was inaugurated in 1959 and was the first Integrated Steel Plant in the public sector in India. In 2013, RSP commissioned their No. 5, 4060 m³ Blast Furnace, India's largest. It was built as a turn-key project by a consortium consisting of Danieli Corus and Tata Projects Ltd. and is entirely based on the technology and know-how of Danieli Corus. The new Blast Furnace is the key element of an expansion program that doubles the plant's production capacity and with much of the existing ironmaking capacity reaching the end of its technical and economic life span, it enables RSP to meet existing as well as growing demand for its products. This article discusses how this greenfield Blast Furnace was built in an existing and operating Integrated Steel Plant. It covers the accommodation of land, planning of the new installation to fit the available plot as well as the updated logistical lay-out of the plant. Technical details of the installation are presented, including their consequences for RSP's environmental performance and new perspectives for campaign planning.

Aug 2, 2018

By Tiago Fernando de Abreu e Silva Tomanik

Massa plástica refratária e placas isolantes têm sido utilizadas por um longo período em Fornos de Reaquecimento de Placas e Tarugos na Indústria Siderúrgica. Novas tecnologias para o revestimento refratário tem ganhado crescente interesse nos últimos anos em função da redução no consumo de combustíveis, redução em tempo e custos de manutenção e, consequentemente aumento de produtividade. Esse trabalho apresenta o desenvolvimento de um novo concreto isolante, de aplicação por projeção, para condições de alta temperatura, que permitiu a substituição do concreto denso na face de trabalho. Essa nova tecnologia permitiu uma redução no tempo de reparo e alta confiabilidade, pois suporta muito bem as agressivas condições da atmosfera do forno. Também será discutido o futuro desenvolvimento de projetos com significantes economias em energia.

Oct 30, 2017

By Alexandre Gonçalves Andrade, Crisley Dellaqua Pacheco, Gabriel Miranda Teixeira, Aline Maria Santoro Nasaré, Tatiane Ferreira Alvarenga

Diffuse emissions are that directly related to particulate matter suspended from civil structures, materials disposed in conveyor belts carried out by wind, stack e reclaimers operations and that one where dust collectors are not able to act correctly. Vale implemented in the last years a unique system capable to measure this kind of dust, called RAMPs (Dust Monitoring Automatic Network), which creates an analytical net in Tubarao industrial site, located in Vitória, ES. In order to prevent diffuse emissions in Tubarao’s pellets stockyard, it was proposed and developed a predictive model based on operational and climate variables available on the site, using big data and advanced analytics tools. The models developed shows to be adherent to the real emissions rates measured by the RAMPs and proved to be an efficient tool to predict emissions over the internal target with 4 hours of precedence.

Oct 1, 2019

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

By Marcus Vinicius Dias Garcia

O presente trabalho tem por objetivo contribuir para a preservação refratária de baterias de coque, apresentando uma metodologia de planejamento e controle. A condição dos refratários de baterias de coque é crucial para sua produtividade e para o cumprimento de diretrizes ambientais. São desafios (i) a identificação precoce de danos e previsão de seu efeito no desgaste global da bateria, para hierarquia de reparos; (ii) a seleção da técnica apropriada a cada reparo. No presente trabalho, os autores compilam o estudo da progressão de danos sob diferentes tipos de reparo ao longo de mais de 30 anos em baterias heat-recovery e convencionais, de diversos modelos construtivos, e o combinam a tecnologias de inspeção para consolidar uma metodologia de gestão da preservação refratária. A metodologia foi aplicada em baterias localizadas no Brasil, avaliando a condição de mais de 400 fornos em 90 dias. Para a bateria mais crítica, foi identificado um potencial de prorrogação de vida útil em torno de 10 anos.

Aug 17, 2017

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Diego Ruben Martin

Este trabalho objetivou comparar, por meio de experimentos desenvolvidos em uma fundição, através da adição de três inoculantes diferentes (IM-22 com FeSi-Ba/Zr, G 20 com FeSi-Ba) e IMSR 75 com FeSi-Sr), para observar as características da vida util de ferramentas na usinabilidade das peças, microestrutura e propriedade mecânica. A metodologia da pesquisa se baseou em analisar principalmente pelo processo de fresamento o ferro fundido cinzento GG-25 inoculado diferentemente, denominado de acordo com a Norma DIN EN 1561. As formas de avaliação dos resultados terão como base uma análise quanto ao desgaste da ferramenta, acabamento superficial, análise microestrutural, composição química e propriedades mecânicas do material da peça. Os resultados mostraram que dentre os inoculantes aplicados o com Sulfeto de Estrôncio (SrS) apresentou-se mais estável termodinamicamente que as amostras inoculadas com os outros dois inoculantes, pois ele levou a uma variação da energia livre de Gibbs mais negativa e portanto mais favorável a formação de núcleos com raio crítico (rc) maiores, o que permitirá uma solidificação com nucleação heterogênea. Todavia o respectivo inoculante também foi mais eficiente na formação de uma microestrutura mais estável, com maiores quantidades de células eutéticas e vida útil do inserto mais longa quando usinado.

Aug 16, 2017

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Alessandro de Castro Corrêa

A comparação de processos de soldagem é uma tarefa complexa por envolver diversos atributos. A designação dos pesos dos atributos a serem avaliados é uma etapa fundamental na análise de problemas multicritérios; contudo, por vezes, a única informação que se obtém é a ordem de prioridade. O objetivo deste trabalho foi calcular os pesos das propriedades destinadas à comparação de processos de soldagem em aço inoxidável AISI 316L para o reparo de eixo naval com base na ordenação fornecida pelo tomador de decisão. Os atributos considerados foram taxa de deposição, energia de soldagem, rendimento econômico, diluição e relação reforço-largura. Os métodos de atribuição de pesos aplicados foram o de ponderação igual (Equal Weights), ordenação recíproca (Rank Reciprocal), somatória (Rank Sum), ordenação exponente (Rank Exponent) e o método do centroide (Rank Order Centroid). Para se verificar o efeito da escolha dos pesos estimados numa avaliação multicritério, avaliaram-se dados reais, aplicando-se a Ponderação Aditiva Simples (Simple Additive Weighting). Os resultados indicaram que diferentes atribuições de pesos podem alterar a posição das alternativas. Foi sugerido que a elaboração tabela ou gráficos com as distribuições de pesos pode ser útil para que o tomador decisão identifique a que melhor reflete as suas preferências.

Oct 30, 2017

By Olívia Cristina Petriz Monteiro

A Companhia Siderúrgica Nacional (CSN) possui uma Oficina de Manutenção Mecânica Central que fornece serviços de reparo, fabricação e manutenção de conjuntos mecânicos e componentes. A usinagem é um dos setores de maior demanda durante o reparo na Oficina e é considerada o grande gargalo entre as etapas de reparo/fabricação. Na busca por uma melhora na qualidade do atendimento e dos serviços prestados, o trabalho teve como objetivo identificar e implementar um novo sistema de medição para o Controle de Qualidade da Oficina Mecânica, reduzindo a demanda de inspeções dimensionais e geométricas para o setor de Usinagem. Com a compra dos instrumentos de medição tridimensional, o Laser Tracker e o Braço de Medição, foi possível aumentar a disponibilidade da usinagem, diminuir o tempo de inspeção de peças, acelerar o processo de decisão dos reparos, reduzir o tempo de entrega dos equipamentos, aumentar a confiabilidade das inspeções, além de e efetuar eventuais serviços de medição em campo.

Aug 8, 2018

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By Pablo Altoé Amorim, Bruno Sellitti Borges, Otávio Lube dos Santos, Arthur Pizetta David, Matheus Diogo Penido da Silva

Automation is in everywhere nowadays, including within companies and industries, and is therefore fundamental and essential for production, quality and process control of them. There are many ways to automate a production line or a machine can be through relay logic, Programmable Logic Controllers (PLCs), and even more modern microcontrollers with native Internet of Things (IoT) support can be used. What are the advantages and disadvantages of each approach? A PCB was created using more modern microcontrollers programmed in C, C ++ and Whiting language to simulate a replacement of a PLC in an actual machine. Having a very positive result, being able to handle the machine manually via Wi fi besides being able to also perform a real-time monitoring of the machine's motors through the mobile phone, thus entering the IoT and fitting into the Industry 4.0.

Oct 1, 2019

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Abraão Santos Silva

Juntas soldadas são regiões críticas quanto a fraturas. Neste estudo foi analisada a tenacidade à fratura de soldas de reparo de tubos de mastros de sonda de perfuração de petróleo. Foram escolhidos os tubos principais de sustentação dos mastros. Seções do mastro são corriqueiramente reparados por soldagem TIG de raiz e preenchimento por eletrodo revestido. Estes processos provocam modificações metalúrgicas na zona termicamente afetada da solda, o que pode ter reflexo na tenacidade à fratura dos tubos. Foram produzidos corpos de prova para medir a tenacidade à fratura do metal base e da zona afetada termicamente. Os resultados indicaram que não houve redução de tenacidade a fratura devido as alterações microestruturais da zona afetada e isto foi associado ao procedimento de soldagem multipasses utilizado.

Aug 16, 2017

By Eustáquio Vieira Junior

O Alto-Forno 3 da Usiminas, em Ipatinga, possui três regeneradores de câmara de combustão interna e passou por sua última reforma em 1999. Nessa reforma, não foram realizadas alterações de projeto nos regeneradores, sendo somente substituídas as fiadas superiores da parede de partição entre as câmaras de combustão e de regeneração e do checker, que se encontravam desgastadas. No decorrer de 2007 e nos anos seguintes, verificou-se a queda de tijolos refratários na região localizada acima do queimador cerâmico do Regenerador 7. Durante o processo investigativo, adotou-se a inspeção por videoendoscopia a partir de 2010. Face à deterioração da região onde se concentravam as quedas de tijolos e à postergação da reforma do Alto-Forno 3, decidiu-se pelo reparo a quente deste regenerador. O trabalho apresenta o histórico das ocorrências no Regenerador 7, as intervenções anteriores ao reparo, o planejamento e os resultados obtidos a partir da operação com dois regeneradores e o desempenho dos regeneradores do Alto-Forno 3 após o reparo a quente no Regenerador 7, mostrando a eficiência do reparo realizado.

Aug 2, 2018