Search Documents

By Clebson Joel Mendes de Oliveira

Sulfur control in steel have been challenging process experts since the discovering of it deleterious effect on most of steel product properties. To separate this slag from hot metal is mandatory to complete desulfurization process. The preferred method is to skim hot metal surface physically removing the contaminated slag, attributing to the operator the evaluation of skimming efficiency. Thus, we present a new lower cost system using image processing methods foreseeing a future full automation skimming process.

Aug 16, 2017

By Elen Mancini Santi Paulettor, Vinicius Calheiros, Eduardo de Oliveira Cabral

At this paper, Eirich will present its new tool for sinter analysis integrated to the sintering control system. For stabilization and optimal, continuous control of the sintering process, QualiMaster MT1, a device was developed which guarantees fully automatic representative sampling and material analysis and thus a high and stable sintering quality. Mining tailings often has a considerable proportion of valuable substances. In addition to this work, we will also present our mixing technology that allows the economic recovery of these mining tailings.

Oct 1, 2019

By Cleber Caetano Thomazi

Rotary kilns are continuous process equipment used on calcining of nickel ore. The chemical and physical reactions are created by means of heat up the material to predetermined temperatures. Tertiary air fans are attached to the kiln shell to maintain oxidizing/reduction conditions. Special ducts orientate the air flow inside the kiln. In the present work, two types of failure on distinct tertiary ducts mounted on the same kiln are reported. Chemical analysis, hardness test, metallographic and fractographic examinations were carried out. Fabrication related problems and creep were identified as the root causes of damages.

Oct 30, 2017

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By Juliano Braz Possatti, José Fagundes Júnior

This project involved a teamwork including process control, maintenance and operation specialists, R&D and CTO experts to identify and actuate on each opportunity to increase charging temperature, furnace efficiency, decrease discharging temperature when possible, decrease FM and RM cycle time (mainly speed increase and interpass time decrease), tracking zones optimization, safe use of equipment power limits, safety interlocks revision and tune models for Mill Pacing Control and Slab Design.As result of these efforts, ArcelorMittal Tubarão HSM today occupies a prominent position among the best HSM of similar layout and produced mix of the group and worldwide. This paper will show the path which was followed by the AMT HSM team to achieve more than a 20% productivity increase resulting in a hot coils production per year more than 700 million tons higher.

Oct 1, 2019

By Ulrich Sommers

The Intelligent Furnace (I-Furnace) by SMS group is a smart furnace process and production optimization model. The combination of various tools leads to an optimized heat treatment and production process. It combines a mathematical/physical model to control the furnace with EMG’s IMPOC system for online strength measurement and a newly developed annealing microstructure model to predict material properties. This paper reports about the revamping of an existing galvanizing line, where a mathematical/physical control model has been implemented in combination with an online quality measurement system. This way, the process improvement of continuous galvanizing lines and the quality management of a range of steels including AHSS will be demonstrated. Furthermore, it gives information about the development of the annealing microstructure model to predict material characteristics. Eventually, the I-Furnace will be presented according to the current development and reference status.

Oct 30, 2017

By Gabrielle Luana Jimenez

Aparelhos eletroeletrônicos como computadores e televisões são constituídos por telas de cristal líquido, que ao se tornarem obsoletos são classificados como resíduos, e dispostos em aterros sanitários. Entretanto, na composição das telas de cristal líquido há metais de valor agregado, como o índio (In). Com a fundamentação no processo de reciclagem de telas de LCD, este estudo propõe a recuperação e quantificação desse metal que é encontrado na forma de ITO (óxido de índio e estanho). Para tal feito, foram empregadas rotas hidrometalúrgicas, tendo como principal etapa a lixiviação. Como parâmetros de controle, os ensaios de extração sólido-líquido foram realizados em temperaturas que variam de 50 a 80°C. Com isso, foi obtido resultado de extração do índio em cerca de 60% em massa, nas condições de 60°C e após 4 horas de lixiviação.

Aug 17, 2017

By Humberto Almeida de La Serna, Kayleigh Meneghini, Gabriel Rubio Pirillo, Maurício Guimarães Bergerman

The Mining Annual Report (RAL) is an obligation for every current owner of a brazilian mining process which is already undergoing extraction. This document is basically composed by the company’s annual book balance, where is possible to educe informations that allow to evaluate the mineral market behavior. This research gathered filtered data linked with RAL production and technical responsability between 2010 and 2017, gotten by the Information Access Law, without the real CNPJ of each company, in order to preserve their identity. The results allow to quantify the Brazilian mining production during the period, illustrating that approximately 46% of the companies can be classified as micro, 30% as small, 20% as medium and 4% as large mining companies. It was observed that the micros concentrate the most part of technical responsibles who sign for more than three mines.

Oct 3, 2019

By Alexandre Schultz Rizek

Esse projeto visou a substituição do sistema de controle instalado por um padrão RUSSULA, sistema esse que controla um laminador de barras e de rolos de 500.000 toneladas/ano na Usina Presidente Vargas da CSN em Volta Redonda, RJ/Brasil. Juntamente com o sistema de controle, RUSSULA forneceu um novo posto de operação para a cabine central, com novas telas de operação, sendo um posto “touch”. Equipado com controladores Siemens S7-400, IHM Wonderware InTouch, acionamentos ABB ACS800 e DCS800, o sistema se apresentava ineficaz, exigindo a otimização do processo, aumento de produtividade, diminuição de paradas, diminuição de perdas metálicas e maior confiabilidade no controle, o último através das ferramentas RUSSULA implementadas no software, como por exemplo detecção automática de sucata, controle de tração, controle de laço, rastreamento do material no laminador, otimização de corte das tesouras e barra fantasma.

Aug 17, 2017

By Haysler Apolinário Amoroso Lima, Francisco Pereira Netto, Vladnilson Peter de Souza Ramos, Bruno Nery Stoco, Gilvan Nascimento de Souza

Em um mercado dominado por tijolos de Al2O3-MgO-C, o revestimento de trabalho de panela de aço monolítico e CarbonFree se apresenta como uma tecnologia disruptiva para um novo patamar de qualidade do aço e eficiência energética. O presente estudo relata a motivação para a implementação do primeiro fundo de panela de aço com revestimento monolítico concretado in situ no Brasil, e apresenta uma análise preliminar dos resultados e vantagens observadas. Uma panela da Ternium Brasil foi revestida com refratários de Al2O3-MgO, e colocada em operação sem nenhuma necessidade de ajuste na operação da aciaria. A partir dos dados de processo e das medições a laser, calculou-se o desgaste do revestimento, bem como verificou-se a garantia de qualidade nos aços IF (interstitial free) e a maior preservação na temperatura do aço durante o refino secundário.

Oct 1, 2019

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019

By Fábio de Oliveira Braga

A proteção balística contra projéteis de alta energia, como o 7,62 mm, é mais eficientemente realizada por meio de sistemas de blindagem multicamada (SBM). Estes são formados, em geral, por uma camada frontal de cerâmica, uma camada intermediária de tecido sintético ou de compósito, e uma camada posterior de um metal dúctil. Em trabalho recente, Monteiro et al. (2016) estudaram um SBM com camada intermediária formada por compósito reforçado com tecido de rami em substituição a um laminado tecido de aramida. Eles obtiveram resultados satisfatórios com boa redução de custo. No presente trabalho, foram investigadas fibras de rami in-natura como substituição ao tecido de rami na camada intermediária compósita. Os resultados foram comparados ao desempenho de um compósito reforçado com 30% de tecido de aramida, bem como aos resultados anteriores. Observou-se que a utilização dos compósitos reforçados com fibras de rami manteve o bom desempenho do SBM, com um custo cerca de 5 vezes menor que o SBM com aramida, e 60% menor que com tecido de rami.

Oct 30, 2017

By Kenneth Williams

Economic drives dictate the exploitation of formerly less attractive ore bodies located close to or even beneath the water table. These ores can cause handling problems and expensive downtime of processing equipment due to their increased adhesive characteristics and are colloquially termed as “wet and sticky” ores. In order to gain a better understanding of the causes of poor handleability, experimental test methods for wall and inter-particle adhesion within bulk solids samples were developed and validated. The results confirmed that adhesion of bulk solid to equipment surfaces is mainly governed by capillary pressure. It can therefore be described using the Young-Laplace equation, which implies that adhesion is primarily dependent on the interfacial water between bulk material and the adhesion partner. Accordingly, the governing material parameters of adhesion are its capillarity and permeability, as these two characterize water transport to or from the interface of the adhesion partners. Furthermore a threshold for the classification of a material as wet and sticky based on the measurements of adhesion has been proposed.

Aug 17, 2017

By Marcus Vinicius Laudares Mendonça

SMS calculates and improves tooth and flank profiles individually to realise a homogeneous pressure distribution over the complete load flank. With a tooth profile and flank profile according to AGMA, ISO or DIN standard the contact pressure varies along the load flank. To realize a homogeneous distribution of the contact pressure and to avoid a premature mesh, SMS improves the tooth profile and flank profile in three steps. First SMS is doing a preliminary calculation and design according ISO, DIN or AGMA standard, with safety factors based on more than 125 years of experience. Second SMS calculates and checks the local contact pressure at the load flank under consideration of shaft, gearing and housing deformation, as well as the bearing behaviour. Finally SMS calculates and designs an improved tooth profile and flank profile to receive a homogeneous contact pressure at the load flank. The result is an increase of the torque transmitting capacity of up to 30% of the SMS advanced gears with the same outer dimensions than traditional gears.

Aug 17, 2017

By Mariana Macedo de Oliveira Lima, Pedro Emílio Gazola, Andrei Locatelli

Boron steel is used in the industry due to its great wear and impact resistance. During the hot rolling production of 15B29 steel flat bars it is a recurrent problem that the bars will present warping while on the cooling bed. Control this phenomenon is an opportunity to have better productivity, preventing metallic losses. Through the observation of the macro and microstructure samples produced with different reheating temperatures and cooling rates, it was found the presence of residual stresses and cracks on warped bars macrostructure. The residual stresses appearance suggest that the material cooling is too fast. Billets temperature on the reheating furnace of 1230°C reduced to 1100°C and the production pace slowed down. Bars temperature when arriving the cooling bed was reduced from higher than 670°C to 625°C. The results obtained made it possible to produce the material with better quality, reducing the warping effect at the cooling bed. The major influence on the materials warping was identified as the cooling rate at the cooling bed and the reheating furnace temperature was adjusted to provide a homogeneous temperature along the bars.

Oct 1, 2019

By Maurilio Pereira Gomes

The aim of this work was to heat treat and characterize sintered valve seat inserts (VSI). The powder metallurgy route was the only way found to substitute cobalt and lead, used in the VSI original alloy, due to their high cost and toxicological effect, respectively. The studied VSI was obtained with AISI M2 high-speed steel powder mixed with iron powder and other additives such as manganese sulphide, graphite, zinc stearate, carbides and copper, which was added by metallic infiltration. All the VSI were air quenched and double tempered, for one hour each, at seven different equidistantly temperatures, ranging from 100 °C up to 700 °C. The physical and mechanical properties were evaluated by means of the VSI apparent density, apparent hardness and crush radial strength. The chemical composition was determined through gas analysis, for the light elements such as carbon and sulfur, and energy dispersive X-ray fluorescence spectrometry for other elements. Microstructural characterization was performed with the support of scanning electron microscopy and energy dispersive spectroscopy. Regarding the VSI final application, the best results were achieved with the inserts air quenched and double tempered at 600 °C.

Oct 30, 2017

By Paulo Paranhos Gonçalves Filho

O trabalho apresenta as etapas e resultados obtidos através do projeto de adequação da iluminação de Usinas de Pelotização da VALE no Complexo de Tubarão em Vitória - Brasil utilizando tecnologia LED (Light Emitting Diode). Foi elaborado um estudo luminotécnico das usinas, assim como levantamento in loco para elaboração do projeto de adequação e substituição das luminárias LED. Houve também um estudo da tecnologia e busca por tipos de luminárias que melhor atenderiam cada área especificamente. Foram feitas medições de potência instalada e iluminância das principais áreas das usinas para posterior comparação com os resultados alcançados. Nas áreas onde a tecnologia LED já foi implantada foi obtida uma redução de 45% em média no consumo de energia elétrica do sistema de iluminação. Verificou-se também um incremento de até 11 vezes no nível de iluminância além da redução das intervenções por parte da manutenção para substituição e/ou melhora da iluminação. A viabilidade da utilização da tecnologia LED foi confirmada pela redução de custo com energia elétrica, redução de manutenção do sistema de iluminação e aumento da iluminância na área com o consequente aumento de segurança no trânsito de pessoas e execução de atividades.

Aug 2, 2018