Search Documents

By F. Keller, R. H. Brown

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By A. A. Smith

The application of indium to bearings was first advocated by C. F. Smsrtl in 1938, for the purpose of inhibiting corrosion of certain bearing alloys. He found that a thin layer of indium plated on the bearing surface and subsequently diffused at elevated temperatures markedly decreased the rate of corrosion in lubricating oils containing organic? acids. Most of his work was done on cadmium-base alloys, although he showed that the treatment was also effective for copper-lead and other; alloys. Since their introduction, indium-treated bearings have found considerable use, particularly in connection with airplane motors.2 Undoubtedly the effectiveness of the indium plate in resisting corrosion depends upon its relative concentration on the bearing surface after the diffusion treatment and after prolonged use at operating temperatures. Some diffusion experiments were made on a number of base metals that had been indium plated, to determine the depth of penetration after heating for reasonably long periods of time. As only the practical aspects were desired, no attempt was made to determine actual diffusion constants. Method Two different series of experiments were carried out to study the diffusion of indium into several base metals. Cast cylinders about one-inch diameter were machined to 0.750-in. diameter, so as to remove all surface imperfections, and final finishing was done with oo sandpaper. The original diameters were very carefully measured with micrometers and then a layer of indium was electrolytically deposited on the cylinders from a sulphate bath.3 In the first series of experiments, about 0.002 in. of indium' was deposited and diffusion, was carried out at 150°C. for a period of 500 hr. in a thermostatically controlled electric oven. After the diffusion period, successive layers were machined from the specimens and analyzed spectro-graphically and chemically—the spectro-graphic examination serving as a guide to determine which layers should be chemically analyzed. Apparently there was some surface oxidation of the indium plate due to the long heat-treatment, which may have had some effect on the diffusion. A1so, the cadmium alloy showed some incipient melting, which probably was caused by the formation of a low-melting eutectic. To eliminate these factors, another series of experiments was carried out by heating in an electrically heated, automatically controlled, oil bath at lower temperature. The preparation of the specimens was the same as before except that a layer of indium 0.0001 in. thick, an amount commonly used commercially on bearings, was deposited on each of the cylinders. Diffusion was carried out at 120°C. for a period of 200

Jan 1, 1944

By A. A. Smith

The application of indium to bearings was first advocated by C. F. Smsrtl in 1938, for the purpose of inhibiting corrosion of certain bearing alloys. He found that a thin layer of indium plated on the bearing surface and subsequently diffused at elevated temperatures markedly decreased the rate of corrosion in lubricating oils containing organic? acids. Most of his work was done on cadmium-base alloys, although he showed that the treatment was also effective for copper-lead and other; alloys. Since their introduction, indium-treated bearings have found considerable use, particularly in connection with airplane motors.2 Undoubtedly the effectiveness of the indium plate in resisting corrosion depends upon its relative concentration on the bearing surface after the diffusion treatment and after prolonged use at operating temperatures. Some diffusion experiments were made on a number of base metals that had been indium plated, to determine the depth of penetration after heating for reasonably long periods of time. As only the practical aspects were desired, no attempt was made to determine actual diffusion constants. Method Two different series of experiments were carried out to study the diffusion of indium into several base metals. Cast cylinders about one-inch diameter were machined to 0.750-in. diameter, so as to remove all surface imperfections, and final finishing was done with oo sandpaper. The original diameters were very carefully measured with micrometers and then a layer of indium was electrolytically deposited on the cylinders from a sulphate bath.3 In the first series of experiments, about 0.002 in. of indium' was deposited and diffusion, was carried out at 150°C. for a period of 500 hr. in a thermostatically controlled electric oven. After the diffusion period, successive layers were machined from the specimens and analyzed spectro-graphically and chemically—the spectro-graphic examination serving as a guide to determine which layers should be chemically analyzed. Apparently there was some surface oxidation of the indium plate due to the long heat-treatment, which may have had some effect on the diffusion. A1so, the cadmium alloy showed some incipient melting, which probably was caused by the formation of a low-melting eutectic. To eliminate these factors, another series of experiments was carried out by heating in an electrically heated, automatically controlled, oil bath at lower temperature. The preparation of the specimens was the same as before except that a layer of indium 0.0001 in. thick, an amount commonly used commercially on bearings, was deposited on each of the cylinders. Diffusion was carried out at 120°C. for a period of 200

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

By A. L. Marshall, F. J Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

The First Conference of the Powder Metallurgy Committee convened in the East Foyer of the Hotel Waldorf-Astoria, New York City, at 9:45 a.m., on Feb. 21, 1944, Mr. John Wulff, General Chairman, presiding. THE CHAIRMAN.-In behalf of the American Institute of Mining and Metallurgical Engineers I welcome all members and guests to this conference on Powder Metallurgy. We hope that this meeting will give expert and novice in the field a chance for discussion. Unfortunately, the subject has been overemphasized by some, and, of late, severely criticized by others. We have here today powder producers, fabricators, and engineers of different viewpoints, who can make the meeting a success. Such success depends not only on the caliber of the papers presented but more so on the discussion. To give you time for a free exchange of views, the papers have been shortened purposely. With the hope that you will all benefit by this conference, I shall turn the meeting over to the Chairmen of the morning session, Mr. Roland P. Koehring, of Moraine Products Division of General Motors, and Dr. R. K. Waring, of the New Jersey Zinc Company. SESSION ON DESIGN FACTORS IN POWDER METALLURGY R. P. Koehring and R. K. Waring presiding The opening paper of the session was presented by Mr. Fred P. Peters, as follows:

Jan 1, 1945

By James A. Barr

[CONTENTS PAGE Foreword. By JAMES A. BARRI A New Core Barrel for Prospecting for Phosphate in Florida. By I. M. LEBARON 2 Prospecting for Phosphate in Tennessee. By W. F. GUENTHER 6 Machine Prospecting in Tennessee Brown Phosphate. By H. O. PICKARD, JR8 Diamond Drilling through Flint Horizons in Tennessee. By HENDON R. JOHNSTON9] Foreword PROSPECTING methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the"grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist[t] who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by- a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals and Chemical Corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by Small, temporary, hand-dug shafts.

Jan 1, 1947

Jan 1, 1944

By E. H. Dix

The purpose of this paper is to introduce the subject of Stress-Corrosion Cracking at the Joint Symposium of the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers. In this Symposium we are concerned with spontaneous cracking which results from the combined effect of high, prolonged stress, and corrosive attack. Stress-corrosion cracking may be considered a specific phase of the more general subject of the effect of high constant stresses in accelerating the rate of corrosion of metal products. The kindred subject of corrosion fatigue in which the life of a metal part under repeated stresses is reduced by corrosive attack is not a part of this Symposium. Likewise "creep," the failure of a metal part by high constantly applied stress, in the absence of a corrosive environment, is not to be included. How- ever, corrosive influences may have more effect on creep failures than is sometimes realized. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium.

Jan 1, 1945

By E. M. Norris

Phosphate deposits are distributed widely over the earth's surface. Of the known areas of deposit, eight fields are of particular interest because of their vast reserves of high grade phosphatic material and the volume of their production that goes to the world's great consuming areas. These fields, in the order of their present economic importance, are situated respectively in Florida, French Morocco, Kola Peninsula of U.S.S.R., Tunisia and Algeria, Tennessee, Montana-Idaho-Wyoming-Utah, Ocean and Naru Islands in the Gilbert group, and in Egypt. The Rocky Mountain deposits have a comparatively low ranking in the phosphate trade of today, but this field contains one of the largest known reserves of phosphatic material, associated with which are recoverable trace minerals, which are of increasing importance in our national economy. The first discoveries of phosphate rock in the western states were recorded in Cache1 and Rich2 counties in Utah, respectively in 1889 and 1897. Mining operations were begun on these deposits near Montpelier, Idaho, in 1906. During the latter year geological studies of the phosphate beds were started by Weeks and Ferrier of the U. S. Geological Survey. These studies have been continued to the present day by a distinguished roster of the Survey's technicians. As a result of this systematic exploratory program, the Survey has published a series of bulletins, papers, and maps, which provide the mining public with a comprehensive study of the exposed

Jan 1, 1949

By Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (I), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profit- ability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus mini- mum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12 ) Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-low- grade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1985

By F. W. McQuiston

Teamwork is the key to an efficient organization. Cooperation among mining staff members is an obligation owed to the company. The more cooperation the metallurgist receives from underground, the higher milling yield will be, which in turn makes for a greater mine profit. There is no pay for metal left in mill tailings. The metallurgist is not in a position to be of help to either the geologist or mining engineer, but can receive valuable assistance from both. Therefore, the metallurgist must win underground cooperation. The mining engineer is usually interested in geology because of its relation to ore control; in milling because that is where the rock goes. However, any overlapping of interest between geologist and metallurgist is quite remote.

Jul 1, 1956

By J. C. Fisher, J. H. Hollomon

The fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actua1 and the theorcticallY computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commcrcinlly available materials. Computatiolls have been made,,2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most importallt of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect conccrns the relation between deformation and the stress required for fracture, Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior com-pressive deformation, This marked ani-sotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffe, et al.3 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence, of the measured fracture stress from the theoretical value, the size effect, and the ergence of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the clement of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only docs the magnitude Of the Fracture stress depend upon the size and shape of these particles. but also its dcpendencc upon strain is affected by changes in 'hap' an' size Or the particles. The precipitate resulting from the age hardening Of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends 0' the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrate' by Griffith4 '0 arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of suficient magnitude to raise the stress at this location to a value comparable with the theoretical strength Of the material. If the cracks were reduced in size, Griffith showed that the observed fracture slrength the by virtue Of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947

By J. H. Hollomon, J. C. Fisher

The fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actua1 and the theorcticallY computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commcrcinlly available materials. Computatiolls have been made,,2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most importallt of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect conccrns the relation between deformation and the stress required for fracture, Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior com-pressive deformation, This marked ani-sotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffe, et al.3 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence, of the measured fracture stress from the theoretical value, the size effect, and the ergence of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the clement of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only docs the magnitude Of the Fracture stress depend upon the size and shape of these particles. but also its dcpendencc upon strain is affected by changes in 'hap' an' size Or the particles. The precipitate resulting from the age hardening Of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends 0' the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrate' by Griffith4 '0 arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of suficient magnitude to raise the stress at this location to a value comparable with the theoretical strength Of the material. If the cracks were reduced in size, Griffith showed that the observed fracture slrength the by virtue Of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947