Search Documents

By Carl Lemke

SOME of the principal metallurgical difficulties en-countered in the differential flotation of lead-zinc-iron sulfide ores arise from the following causes: The oxidized, or partly-oxidized, condition of one or more of the minerals ; impurities in the minerals them-selves; composition and character of the gangue miner-als; soluble salts in the ore; and unfavorable metal ratios. In many of the ores received at a custom mill there are present appreciable amounts of oxidized' or partly-oxidized minerals, although the ores may be substantially sulfides. Often the ores are not oxidized at all when received but on account of operating condi-tions at the mill it is necessary to stock them for several months before they can be milled, and considerable oxi-dation takes place while they are lying in stock. In most ores received at Midvale, when oxidation is pres-ent, the lead and iron sulfides have been more affected than the zinc sulfide, but with some ores the zinc mineral has also become partly oxidized. Some ores, such as those taken from old mine-dumps or from old stopes, may show very little total oxidation, but the greater part of the valuable minerals has been sufficiently acted upon by oxidation to make the minerals very difficult to float. Ores of this character are among the most difficult the flotation operator has to contend with, be-cause the galena, sphalerite, and pyrite are all sluggish in their behavior in the flotation cells. Only a part of the lead mineral will float in the lead circuit. The re-mainder will lag badly and tend to come up with the zinc or, if badly oxidized, will go -through all the flota-tion circuits into the tailing. The zinc mineral, if it has also been affected by oxidation, will act in a man-ner similar to the lead mineral. A hard pull will be required to float a reasonable percentage of it, and this is likely to bring up so much pyrite that it will be difficult to make a zinc concentrate of commercial grade. If it happens that the zinc mineral has not been no-ticeably affected by oxidation it will tend to float in the lead circuit because a hard pull is also required in that circuit in order to bring up the sluggish galena. When only a fraction of the sulfide minerals has become partly altered, or completely oxidized mineral is present in relatively small quantity, it is usually possible to make reasonably clean concentrates of all three sulfides, that is, lead, zinc and iron concentrates. Most of the oxi-dized and semi-oxidized minerals will go into the tailing and the losses will be proportional to the oxidation.

Jan 4, 1927

By Ezequiel Ordoñez

THE great activity with which the oil resources of the northern Cantons of the State of Veracruz have been developed has largely resulted from the great success obtained by the important explorations carried out since 1902 in the Ebano district in the North, and several years later near Tuxpam, in the South. It must not be thought that these successes were quickly obtained, since the preliminary studies by good experts, the acquisition of what were thought to be the most promising coast lands, the extensive clearing thereof, and finally the number of unsuccessful drillings at great depth, signified an original outlay of some ten's of millions of dollars before finding commercial oil. The discovery of oil in industrial quantities at Cerro de la Pez, Ebano district, and the famous Dos Bocas gusher some years later, which was burned, once and for all made famous the Veracruz coast, where today is concentrated the Mexican output of mineral oil. In .1917, this production was nearly 50,000,000 bbl. It is well known that this output represents only a fraction of what the wells in actual production can furnish, because with adequate means of transportation and storage, the present extraction could be somewhat over 300,000,000 bbl. a year. These enormous potential oil resources of the Veracruz coast proceed from a relatively small number of wells, scattered over a few oil fields, separated from each other by large unexplored areas, wherein may be found other favorable fields which, in time, will undoubtedly become just as great centers of oil production. Experts who know our Gulf Coast believe that lands with commercial oil resources lie not only between the Panuco amid Tuxpan Rivers, but that indications are that the oil zone of Mexico, with more or less interruption, takes in the coast zone from Northern Tamaulipas to the foot of the Sierra Madre of Chiapas, and the banks of the Usumacinta River. This generalization is not merely the outcome of optimism, but is the result of the persistency with which one finds, throughout this Gulf Coast, the most usual characteristics upon which we depend for recognizing oil-bearing lands.

Jan 5, 1918

By W. Arthur White

Underclay squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay-making it more plastic-or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards.

Oct 1, 1956

By J. E. Drury, W. M. Byers, E. J. Lynch

Measurements made with starch ~~~~s indicate that the Presence of starch serves to depress the streaming potential of a clay mud system. Measurements with pure starch slurries show that the addition of NaCl or CaO reduces the streaming potential significantly. The addition of NaOH, however, causes only a minor reduction in potential even when there are large changes in mud resistivity. INTRODUCTION In their excellent study of the streaming potential, Hill and Anderson' proposed that the presence of conductive solids within the filter medium will reduce the generated potential. This theory was demonstrated with measurements on shaly sandstone cores having various "b" factors; the cores with the higher negative b factors showed markedly lower potentials. (The factor b was originally defined by Hill and Milburn2 in an expression relating the resistivity of a shaly sandstone to the resistivity of the interstitial water: log F, = log F,, + b (log 100R,)'. 'he factor b, therefore, is a measure of the contribution of the conductive solids to the total conductivity of the sample. It has been found experimentally to be directly related to the amount of chemically exchangeable ion per unit pore volume.) In the logical extension of this hypothesis to the streaming potential created by filtration through mud cakes, they suggested that the presence of nonconductive starch in a drilling mud would have the opposite effect; i.e., it would cause the streaming POtential to be increased. The high streaming potentials that they observed with lime muds were attributed to this cause. A cross-plot of some of their results which are relevant to this discussion is given in Fig. 1. The lime-mud curves and untreated-mud curve are taken from curves given in their paper. The gyp-mud line was estimated from their statement that the measured streaming potential for gyp muds in the range of 1.5 to 2.0 ohm-m was approximately 18 mv/1,000 psi. These gyp-mud potentials were the lowest that they reported for any of the bentonitic-clay muds, and were the only ones which were less than the untreated-mud potentials. This very low streaming potential of gyp muds has also been observed in field studies.' By way of comparison, a U. of Texas publication4 gives the approxi-ate compositions for lime and gyp muds shown in Table 1. These materials are added to a bentonitic-clay mud base. It can be seen that both of these muds contain significant amounts of calcium salts and that the gyp mud has the higher concentration of starch. It would appear from this and from the data shown in Fig. 1 that starch may well be the cause of a streaming-potential reduction, rather than a potential increase. EXPERIMENTAL A series of streaming-potential experiments has been performed using a cell of a design similar to that reported by Wyllie.5 Calomel electrodes were used in both the mud slurry and the filtrate. Pressure in the cell was generated with high-pressure nitrogen. The primary objective of the investigation was to determine the effect of starch on the potential. Five different slurries were made which ranged in composition from untreated ben-tonitic mud (Baroid Aquagel) to a pure starch suspension (Baroid Im-permex). The intermediate slurries were prepared by mixing together a 9-lb/bbl clay mud with a 12-lb/bbl starch suspension in the ratios 1:3, 1:1 and 3:1. When starch was used alone, it was necessary to use an 18-Ib/bbl mixture, since leaner mixtures would not form a suitable filter cake. The clay mud used in the experiments was aged for three months before use. In addition to this series of measurements on the starch-clay mud mixtures, other experiments were performed to determine the effect on the potential of the absolute starch and Aquagel concentration, and the effect of adding various chemicals. RESULTS The effect of starch on the streaming potential is shown clcarly in Fig 2. Increasing percentages of starch resulted in n continually decreasing

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide. application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and. establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By Joseph E. Pogue

THAT the domestic consumption of gasoline displays a marked seasonal variation, with a low in the winter and a high in the summer, is well known. It is logical to expect that the nature of the variation has itself been undergoing a change as a result of improvement in roads, general employment of closed cars; and growth of mass haulage; but so far as I am aware the change in seasonal variation has never been investigated and measured. It is the purpose of this paper to present the method and results of such an investigation undertaken as a contribution to the technique of planning operating schedules now so prominent in connection with the functioning of the industry under a Federal quota system. For the method employed I am in-debted to the suggestions and help of Frederick R. Macaulay', who kindly looked over the work sheets; and credit is due Barnabas Bryan, Jr., for assisting in the computations and the graphic work. Ideas for the approach to the problem were also derived from an article by Aryness Joy, and Woodulief Thomas of the Division of Research and Statistics of the Federal Reserve Board*-.

Jan 1, 1934

By M. Gensamer

IN applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "Lüders"' lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiter1 though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By Robert D. Lonqyear

SOMEWHAT biased by pride in twentieth century achievements, most of us mining engineers and diamond-drill operators look upon core drilling as a relatively modern practice. The invention of the diamond drill is generally ascribed to Rudolf Leschot, who made use of diamonds in 1846 in drilling blast holes in the Mont Cenis tunnel in Switzerland. In vain we search Agricola and other early writers on mining for signs of diamond drilling. We have, therefore, concluded that it was unknown until the middle of the last century. The trouble with this conclusion, as most prospectors will tell us, is that we "don't dig deep enough"; for it now appears that the archeologists have been putting one over on us for the last fifty years.

Jan 1, 1936

By H. S. Chiang, D. F. Lu, S. S. Peng

INTRODUCTION The most important element in a successful lingual mining is a good roof control. The modern longwall mining employs hydraulic powered supports for roof control at the face area. The application of hydrau¬lic powered support requires the knowledge of over¬burden strata behavior for proper selection of sup¬port type and capacity. Failure to do so could lead so serious loss. There are several methods available for determining the required support capacity (1-3). While these methods are simple for application, they do not include the complicated roof behavior observed in longwall mining. As research progresses and operational experience accumulates (4,5), the concept about the designing and selection of powered support improves. The design of a longwall powered support consists of three major phases: 1. structural integrity and stability of the powered support, 2. external loadings induced by the movements of the overburden strata, and 3. interaction between the support, roof and floor. Phase 1 involves structural analysis (5) and full-sized testing (6) of the supports. Its validity is limited by the accuracy of the assumed external loading because of the uncertainty about the actual loading underground. The third phase includes the reaction of the support and the floor to the movements of the overburden strata and vice versa. Among the three phases, the second phase concer¬ning the external loading seems to be the least known because of the complicated behavior of the roof strata. There are many unresolved problems. For example, does the main roof break periodically and cause periodic roof weighting in the face area? If so, are there any rules governing its behavior? How does the roof load on the support canopy! Finally, how can one determine the required support capacity and select a proper type of support to meet a certain roof behavior? In order to answer those questions, underground instrumentation and observations were performed at 4 longwall panels in 3 separate mines for the past two years. This paper summarizes the current findings. PANEL LAYOUTS AND EQUIPMENT EMPLOYED The three mines selected are all located in West Virginia; two in northern and one in southern West Virginia. As shown in Table 1, seam conditions (i.e. seam, depth and thickness) and panel layouts are different among the three mines. The most significant difference in equipment is the face powered supports. Three mines used three different types of shield; 2-leg caliper, 2-leg lemniscate, and 4-leg lemniscate chock-shield. (Fig. 1) UNDERGROUND INSTRUMENTATION AND OBSERVATION PROGRAM Two events were instrumented in each observed longwall face: one was the hydraulic pressure (resistance) of the powered supports and the other was the canopy load distributions. In addition, the gob caving conditions were visually observed and recorded. Leg and Support Resistances One or two automatic Weksler Pressure Recorders were installed at the designated shield support,. In most cases, the daily charts were used to record the pressure variations in both the front or the rear legs (for the 4-leg shield), or in both the leg and the fore-pole ram (for the 2-leg shield). The recorded pressure w a s then converted to load or resistance by multiplying it by the cross-sectional area of the hydraulic leg or canopy ram piston. Fig. 2 shows the typical pressure-recorded charts for the 4-leg and 2-leg shields in a 23-24 hour period. The support resistance is the summation of the resistance in each of all the legs for that support. Generally, the resistance of the fore-pole ram will not be considered in determining the capacity of the support because of its rather small vertical compo¬nent force at the tip of the fore-pole. Canopy Load Distribution External load distribution on the canopy as exer¬ted by the roof was monitored. The measurements employed 12-14 pieces of pressure cells (6-inch square) that were uniformly arranged in two rows on the canopy. After support setting, the pressure changes in the cells were monitored at various stages of the mining (supporting) cycle while the support leg pressures were recorded continuously by the pressure recorders. Based on the calibration chara¬cteristics of each pressure cell as performed in the laboratory before and after each underground test, the cell pressures were converted to actual loadings. From these load measurements the canopy load distri¬butions and the relations between measured canopy loadings and support leg resistances were determined. Accordingly, the supporting efficiency of the shield support can be determined.

Jan 1, 1982

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

By B. F. Tillson

HAVING been asked to talk about recent devel-opments in mining equipment, I chose the sub-ject of small units of storage-battery locomo-tives which recently have been developed with the idea of motorizing transportation in the mines as far as possible, replacing the manual labor of hand-tramming. Metal mines are probably less advanced in this field than coal mines, where transportation of large ton-nages on any one level is quite common. Of course, metal mines, where large tonnages are handled on any one level, are as advanced as coal mines, and storage-battery locomotives for main haulages are used quite commonly in such metal mines, but the mines having levels at many intervals in the depth of the orebody, or a number of intermediate levels in which a consider-able amount of hand-tramming has to be done, and small metal mines in which the size of the orebody does not seem to warrant the initial capital expenditure for the driving of main haulage levels and installation of rock and ore chutes and raises for the delivery of the broken ore and rock to the cars have been at consider-able disadvantage in replacing manual labor by some mechanical means of transportation. Several years ago the field was canvassed among the manufacturers of electric-locomotive equipment and the conclusion was reached that the art had not been devel-oped to the advantage of metal miners who desire to replace small units of labor by locomotive equipment. The need for such small locomotives is all the more em-phasized by the development in the past few years of mechanical mucking-machines (loading equipment for filling the cars from muck piles on the level). Any me-chanical loader is a liability instead of an asset unless means are also provided for keeping the material away from the loading-machines. Therefore the transporta-tion system must be equal to the capacity of a loading-machine, otherwise the latter is idle such a large per-centage of its time as to prove an unprofitable invest-ment. So there is a need for portable, small haulage units to handle small mine cars in many metal mines, and, naturally, units are desired which can be so readily shifted from level to level as to facilitate their free use. Of course, in mines in which each level comes to the shaft it is not such a difficult problem, but many mines have a great many intermediate levels which must be approached through raises, timber slides or other small openings required to transfer ore and to get timber and other supplies to those levels.

Jan 5, 1927

By AIME AIME

IN view of the approaching visit to Japan and the Imperial Steel Works at Yawata by our members, the following notes on present conditions in the industry there will be of interest. The data were collected by the representatives of the Bureau of Foreign and Domestic Commerce in Japan and are furnished here through the courtesy of the Department. In connection with the proposed suspension of both new and old Government undertakings and the general depression in building, which is expected to result from the retrenchment policy of the Government, some cuts in iron and steel prices have been made by dealers. It is expected that the Yawata Steel Works may reduce its round bar prices for November delivery by 1 yen.

Jan 1, 1929

By William P. Blake

The occurrence of the manganiferous variety of wolframite at a new locality in Arizona was announced in the month of May last." It occurs in the granite hills of the Dragoon mountains, in Cochise county, about 6 miles north of Dragoon Summit station, on the Southern Pacific Railway of Arizona. It is found in veins of white quartz, traversing a coarsely crystalline granitic gneiss, and, so far as yet determined, is without association with other metallic minerals in the same veins, except small quantities of scheelite. It is a very pure form of the mineral, and contains but little iron, the base being manganese oxide. The color is brownish-red; it is nearly the same as the color of the mineral originally described by E. Riotte from Mammoth District, Nevada.† Thin films or plates on the broad cleavage-surfaces, and thin cleavage-flakes, seen by transmitted light, are ruby-red, or rather more like the color of red zinc oxide or the mineral known as clintonite. By long-continued weathering the surface becomes less deeply colored, and assumes a bronze-like luster, like the dull oxidized surface of

Jan 1, 1899

By George H. K. Schenck, Peter G. Donald

There is an accelerating acceptance of change by management of cement companies. Diversity of response is noticeable in efforts across the country to reverse the downward trend in profits that brought margins in 1966 to the lowest point in 20 years. New concepts are emerging among managers as they seek to increase the efficiency in use of the basic corporate resources of men, capital and technology. The shift towards computerized control of cement manufacturing is making new gains as is diversification of cement companies into allied fields such as production and sale of natural and light- weight aggregates, crushed stone and concrete products. Increased interest in special products such as white cement and further moves overseas are also significant. Perhaps the most dramatic event of recent years occurred in Washington at hearings before the Federal Trade Commission where cement producers split on whether there should be FTC guidelines that would prevent ownership of ready-mixed concrete producers by cement companies.

Jan 4, 1967

By V. M. Lovell

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysaccharides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By Guy Jordan

HIGH-IRON cements have a number of advantages over cements carrying little or no iron. The presence of iron in, Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to freezing and thawing, and increases the resistance of the cement to sea or sulphate waters. During the past few years the construction of numerous dams through-out the Southeast by the Tennessee Valley Authority has stimulated the production of high-iron cements. At present a great number of specifica-tions call for an iron cement, and the industry is supplying this demand with a Portland cement carrying approximately 5 per cent iron oxide. Several manufacturers are now making practically all of their cement of this type and a number of others manufacture it as a special cement over short periods to meet demands from the Tennessee Valley Authority and other buyers. The recent increase in the use of iron in Portland cement has created a market for iron products that previously was nonexistent. The chief sources of supply for the cement manufacturers at present are iron sand, iron sinter and slag, and ocher. The Copperhill mining district, Ten-nessee, supplies both iron sinter and slag for use in cement. The Carters-ville district supplies iron sand, ocher, and some iron resulting from the magnetic separation of iron from barite. The advantages of these products vary according to the chemical properties of the raw materials and the methods of handling used by the different manufacturers. Where the iron is to be handled by conveying belts and in hopper cars, the iron

Jan 1, 1939

By Nathaniel Arbiter, Arthur F. Taggart

THE fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. EXPERIMENTAL Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,' and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: 1. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. DISCUSSION OF RESULTS Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether

Jan 1, 1943

By E. P. Pfleider, W. D. Lacabanne

ROTARY-percussive drilling is a new method of drilling hard rock. Designed to give variations in thrust, revolutions per minute, and torque ranges, these drills combine the high efficiency of the rotary system in soft rocks with an increasing amount of percussive action in rocks more difficult to fragment. Fundamentals of the rotary, percussive, and combination systems have been described in detail in various papers-most recently by C. Fairhurst and W. D. Lacabanne1-but there is still much basic work to be done on the interplay of actions in the rotary-percussive system to enable the drill designer to achieve the highest efficiencies. Whereas the original units struck light blows of only 15 to 30 ft-lb, adequate for medium hard rocks, the present trend is to piston blows of 50 to 65 ft-lb in order to cope with the granites and other rocks having Shore hardnesses of 75 or more.

Jan 7, 1957

By W. M. Rust, W. D. Mounce

THE almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubt- less other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations.

Jan 1, 1944

By George E. Aiken

Subzero temperatures of the Arctic pose some critical engineering problems for the developer and operator of open pit mines. Undoubtedly, the single most troublesome manifestation of this climate is permafrost. Underlying about 20% of the world's land area and 85% of the state of Alaska, permafrost has not only made its impact on building construction and mine excavation, but has created a legitimate threat to the delicate balance of nature existing within the Arctic environment. The recognition of permafrost areas by geomorphology and an understanding of its other complex developmental factors are the basis for two major concepts in building construction. The active method involves the eventual thawing of the complete permafrost section and is only useful in shallow areas. However, in some areas of coarse, well-drained material, vegetation may be stripped well ahead of construction and shallow permafrost allowed to method, leaves the perenially frozen ground undisturbed and is to be preferred. In selecting construction sites aerial photos may clearly reveal typical permafrost features.

Jan 5, 1972