Search Documents

Joseph W. Richards was elected Vice-president and Director to fill the vacancy caused by the election of Philip N. Moore to the presidency. Benjamin B. Thayer was elected Director to fill the, vacancy caused by the election of Charles W. Goodale as Vice-President and Director. Sidney J. Jennings was elected First Vice-President of the Institute. George C. Stone was elected Treasurer of the Institute. Rossiter W. Raymond was appointed Secretary Emeritus of the Institute. Bradley Stoughton was elected Secretary of the Institute. Burr A. Robinson was appointed Assistant Secretary of the Institute.

Jan 4, 1917

By R. T. Hukki

BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that [ ] Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate).

Jan 6, 1954

By Samuel B. Christy

As is well known, the ore at New Almaden is cinnabar. Native quicksilver occurs also; but, as a rule, in small quantities only. Pyrite occasionally accompanies the ore. Bitumen is quite common,

Jan 1, 1885

The materials used for pump construction vary according to the nature of the solution handled. The pump materials in use are the result of extended experiment and are all giving satisfactory results. Research is still in progress, particularly with stainless steel and rubber lining, both of which show considerable promise. Following are the materials used: For tank-room acid, carrying about 100 grams per liter free sulphuric acid, hard lead is used. Stainless steel is under investigation. Duriron is satisfactory, but requires very careful handling to prevent mechanical breakage. For pulps containing low acid (10 grams per liter), abrasive solids, ferric iron, copper, etc. pumps are made of hard lead. Stainless steel is satisfactory. For pulps containing no acid but carrying abrasive materials and copper, bronze is used. Pulps containing acid (10 grams per liter), copper, iron and nonabra-sive solids require lead pumps. Rubber linings are under investigation. Clear neutral solutions containing copper are handled in bronze pumps; neutral solutions free of copper, acid, abrasive material, etc., in iron or bronze. The hard lead used contains 13 per cent antimony. The stainless steel has the following analysis: Cr, 20.0 per cent; Ni, 7.0; C, 0.25; W, 4.0; Cu, 2.0.

Jan 1, 1937

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By J. Spotts McDowell

J. W. RICHARDS, So. Bethlehem, Pa.-The paper is certainly an exceedingly, valuable one and it gives detailed information which should be utilized in the following way. There are probably twenty different circumstances or conditions under which silica bricks are used. Sometimes they are used under high pressure, at others under low pressure, at times for low temperatures and others for very high temperatures. If the methods of this paper are followed out, and if the precise mechanical and thermal properties are determined and can be reproduced, the industry can furnish the proper brick for any particular purpose. There is at present only an imperfect classification made as to properties and uses, but we need a "much more scientific classification of the uses to which the bricks are to be put and then should manufacture the bricks suited particularly for each of those purposes. There is one property which is not mentioned in the paper and which is of considerable importance, that is, the 'electrical conductivity. There may be other properties besides, which a good research laboratory can determine, and when we have listed all the various properties and noted the way in which they can be reproduced, the maker can then specify his exact requirements and the corresponding quality of brick can he selected or made to meet them. H. D. HIBBARD, Plainfield, N. J.-About a year ago I had some experience in another country, in melting steel, where silica bricks made in that country failed, but in a different way from those in America. Here, when the bricks get too hot, they are partly melted and string down

Jan 4, 1917

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

By Robert Linton

In 1898, Joseph L. Giroux and J. A. Snedaker organized the Pilot Knob Copper Co. and began developing the Pilot Knob mine at Kim-berly, Nev., for high-grade copper ores, carrying good gold and silver values, that the formation had disclosed. At that time the nearest railroad was over 150 mi. distant. The high-grade ores did not prove to be extensive at this point—at least to the depth (240 ft.) to which the work was carried—but development of neighboring claims indicated extensive deposits of sulfide porphyry ore of concentrating grade lying at shallow depth, and deeper deposits of direct-smelting oxidized ores occurring in limestone near the limestone-porphyry contact. The properties passed through the hands of several organizations, with only meager development, until acquired in 1913 by Consolidated Coppermines Co., whose holdings now comprise 3480 acres of mining claims in the Robinson district. Since that time development has been prosecuted more actively; and for the purpose of determining the most efficient and economical method of treating the ores, considerable testing work has been done during the past three years, both in the laboratory and in actual mill operations. At first, the shipments were of ore high enough in grade to be profitable even with the long wagon hauls to the railroad and prevailing freight and smelting charges. In 1905, a blast furnace and a concentrator were erected at Kimberly. On account of insufficient ore supply, the blast furnace was never blown in and later was dismantled. The concentrator as originally equipped was operated for only about two months, both because the ore supply at that time was not sufficient and because gravity concentration did not yield satisfactory extraction. The location and arrangement of the mill further entailed high operating costs. In 1908, the Nevada Consolidated Copper Co. began to mill successfully, on a large scale, its sulfide porphyry ores, which are similar in character to the adjacent Coppermines ores. After that time, all of the ores and concentrates produced by Coppermines Company were smelted and a considerable part of the Coppermines low-grade ores concentrated at the Steptoe works of the Nevada Consolidated Co.

Jan 1, 1921

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By Eckley B. Coxe

I DES~RE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsylvania, about miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By James D. Reilly

13.1-1. Introduction. COAL RESERVES OF THE UNITED STATES. Bituminous coal is the most abundant fossil fuel in America. With reserves of 1,660 billion tons and assumed recovery of 5070, there is more than 830 billion tons of recoverable coal--enough to assure ample supplies of energy for centuries. Looking at Fig. 13.1-1, coal is found in a majority of the states, including [ ]

Jan 1, 1968

By Christopher Haycocks, J. Richard Lucas

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine design, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environmental considerations and the visible limitations of other energy sources.

Jan 4, 1973

Mineral Industries education as an entity, again and again has sought recognition, always to be turned aside or ignored.1 The incident mentioned in Lost Chapter was only the first of a series of disappointments. The Land-Grant Act is camouflaged here and there in the name of progressive education. A new interpretation may be in the best interests of society in so far as the goose is not killed that lays the golden egg. The primary objective of the act is still "agriculture and mechanic arts" but mechanic arts is not alone mechanical arts or engineering. Mechanic arts was used in a broad sense as a symbol of creative effort in locating and winning the fundamentals of existence - plants, animals, and minerals - from Mother Earth, their primary processing and treatment into foodstuffs and raw materials of industry, their manufacture into useful articles of commerce, and, last, their distribution and utilization. Significantly the great agricultural industry is now at least half mechanic arts. The Association of Land-Grant Colleges and Universities has neglected the mineral kingdom shamefully. The Association embraces Divisions of Agriculture, Arts and Sciences, Engineering, Home Economics, and Veterinary Medicine but has no division relating to the mineral industries.

Jan 1, 1950

By Gloyd M. Wiles

Since D. C. Jackling was famous for his adeptness at organizing and training teams of operating personnel, the subject of mine management is particularly appropriate for a Jackling Lecture. In fact, it is doubly appropriate because in very basic ways Jackling's career changed the nature of the tasks and challenges facing a mine manager. Management of mines, of course, is the art of finding and winning minerals economically from the earth's crust, and it involves the use of all the engineering sciences. But also of prime importance is a skill which is not yet a science-the area of management often referred to as human engineering. Since expenditures on staff and labor may well involve more than 50% of the direct costs of operating a mine, ability at human engineering is just as important as the ability to plan and put into effect the most efficient operating procedures.

Jan 5, 1962

By Ross W. Smith, Salim Akhtar

INTRODUCTION Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collectors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By Raymond Sanford

IT IS difficult to know just when a hoisting rope should be removed from service and a new one substituted. It is desirable to utilize the full life of a rope but, on .the other hand, the damage and possible loss of life, resulting from delay in replacing it may amount to many times the cost of a new rope. In the present methods of inspection the inspector must rely upon accumulated experience and a certain sixth sense or intuition in addition to any rules that may be laid down regarding the number and distribu-tion of broken wires. This condition does not neces-sarily arise from lack of interest among users or makers of rope, but is due rather to the lack of satisfactory or adequate methods for testing ropes to determine their exact condition. The main difficulty in devising a physical test lies in the fact that a number of causes, all operating in different ways, contribute to the deterioration of a rope in service, and affect not only the external conditions but also the inner structure of the material of which the rope is constructed. Wear and broken wires on the outer part of the rope are not difficult to detect, but a test is needed which will clearly indicate the presence of broken wires in the interior portions and the change in strength due to alterations in the structure and properties of the material itself.

Jan 7, 1923

Conquista, the uranium mining and milling complex owned jointly by Continental Oil Co. and Pioneer Nuclear, Inc., has begun operations in Falls City, Texas. The mill has been designed to produce 1.5 million lb of U3O, from 600,000 tpy of ore mined. Currently, the plant processes a maximum 2000 tpd of ore. Mine Planning Texas ore deposits are small and scattered in comparison to other uranium mining districts. Those to be mined at Conquista range from a few acres to more than 100 acres in size. Ore thickness ranges from a few inches to over 15 ft, and depth from less than 20 ft to more than 170 ft below ground surface. Distance from the mill ranges up to 35 mi.

Jan 8, 1972