Search Documents

By Stanley L. Arnot

The Mother Lode district in California is probably better known as the land of Bret Harte and Mark Twain than as a gold-producing district, although in this respect it holds an important place. The history of quartz mining on the Mother Lode dates back to the '50s, when, after the first fever of the gold rush, men began to look for something more permanent, if not more lucrative, than the placers. Since that time, the discoveries, shutdowns, and reopenings of the many mines, together with the varying fortunes of their numerous operators, constitute an interesting chapter in California history, but one too long to include in a description of mining methods. The district is well situated, so far as physical conditions are concerned. The Mother Lode extends along the western slope of the Sierra Nevada Mountains, about half way between the crest and the Sacramento and San Joaquin Valleys, the country traversed consisting of low rolling hills—typical foot-hills. The elevation varies from 1000 to 1800 ft. and the climate is most desirable. There is an abundance of water, timber is easily obtained from the higher foot-hills a few miles east, and cheap hydro-electric power is generated practically on the Lode. These natural conditions are conducive to low costs in mining and have been the deciding factor in allowing profitable exploitation of the comparatively low-grade orebodies. Transportation facilities are not bad. Five branch railroads, from the main trunk lines in the valley, tap the district at intervals of from 10 to 30 miles, and the roads connecting these are fairly good for trucking purposes. Labor is made up of several nationalities, the principal ones being American, Spanish, Jugo-Slav, Italian, and Mexican. There were few Mexicans on the Lode prior to 1919, but the shortage of labor, experienced generally by the mining camps of the country in the years following the war, made necessary the hiring of some. The percentage of Mexican labor rapidly increased in 1920 and for a year or so thereafter, but it has now diminished until at most of the mines only a few Mexicans are working. Of the different nationalities, Americans are the most efficient and Mexicans the least.

Jan 1, 1925

By G. L. F. Powell

g samples of Cu-20 wt pct Ag alloy have been mdercooled to a maximum of 197°C by melting under a slag of commercial soda-lime glass in a vitreous silica crucible. No grain refinement of the primary copper was observed in samples undercooled to the maximum of 197°C. When the samples contained a small amount of oxygen, the copper dendrites were partially recrystallized at undercoolings greater than 97°C. In previous papers'-3 reporting the grain structure of undercooled silver and copper, it was observed that grain refinement was dependent on both undercooling and oxygen content. Grain refinement occurred in undercooled silver when the degree of undercooling exceeded the range 153" to 175"C, while in Ag-0 alloys (0.12 wt pct) fine equiaxed grains were exhibited when undercooling was greater than 50°C. Similarly, copper samples undercooled as much as 208°C displayed fan-shaped growth from a single nucleation site, while the grain structure of Cu-O alloys (0.08 wt pct) was fine and equiaxed at undercoolings larger than 150°C. Thus the presence of oxygen greatly reduced the undercooling at which grain refinement occurred. It was also observed that the change in grain size resulted from recrystallization and was not due to an enhanced nucleation rate in the liquid-solid transformation. It is possible that the influence of oxygen on recrystallization is due primarily to its presence as a solute element. walker4,' reported that, although a grain size change did not occur in pure nickel until the undercooling exceeded 150°C, small grains were observed in samples of Ni-Cu alloy solidified at small and large degrees of undercooling. Jackson et al.6 suggested that the fine grained structure of the Ni-Cu alloy resulted from the melting off of dendrite arms during recalescence. This remelting process may occur in alloys as a result of segregation during freezing which causes a variation in liquidus temperature from point to point within a dendrite. It was therefore decided to undercool copper with a metallic alloying element to ascertain whether the presence of a metallic solute would have a similar effect to oxygen in inducing grain refinement. A Cu-Ag alloy was chosen, since both metals had been shown to behave similarly on undercooling. The alloy Cu-20 wt pct Ag was selected since the eutectic constituent outlines the initial growth form of the primary copper, so that the as-frozen grain structure is not obscured if subsequent recrystallization occurs. This paper describes the results of undercooling experiments carried out with Cu-20 pct Ag samples undercooled to a maximum of 197°C and the effect of oxygen content on the grain structure of the undercooled samples. EXPERIMENTAL Melting was carried out in a small cylindrical resistance furnace using "fine" silver granulate and oxygen-free high conductivity copper. The procedure adopted was to melt the required quantity of silver in air in a clean vitreous silica crucible for approximately 15 min, freeze, and add granulated commercial soda-lime glass to form a complete surface slag cover, after which the sample was melted and frozen several times to reduce the oxygen content. The glass slag cover was approximately 3 in. thick. Pieces of copper (=50 g) were added to the crucible until the required quantity to make 350-g samples of alloy had been charged. Each piece was added quickly to the crucible which was held at a temperature slightly above the melting point of silver. The piece was quickly pushed beneath the glass to minimize oxidation and any oxide coating usually decomposed before the piece had settled down into the silver. After the full quantity of copper had been added, the melt was stirred with a silica rod to hasten homogenization and a Pt/Pt 13 pct Rh thermocouple enclosed in a vitreous silica sheath inserted for temperature measurement. Heating and cooling curves were recorded on a potentiometric chart recorder fitted with a zero suppression unit. The milli-voltage range of the recorder was adjusted so that temperatures could be read to 1°C. Heating and cooling curves were taken every hour until three consecutive readings gave the same solidus-liquidus range, consistent with the solidus-liquidus range for this alloy composition by reference to Hansen and Anderko.7 Metallographic examination of samples frozen at this stage, failed to show any variation in composition from bottom to top of the ingot. Consequently, it was considered that the melt was homogeneous at this stage and undercooling experiments were then car-

Jan 1, 1970

By R. F. Domagala, M. Hansen, D. J. McPherson

Iodide zirconium was combined with calculated amounts of nitrided zirconium sponge and arc melted to prepare alloys in the 0 to 6 wt pct N region. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat-treated specimens permitted construction of the binary phase diagram from 0 to 6 pct N. Features of the diagram include the peritectic formation of both a and ß solid solutions. The maximum solubility of nitrogen is 0.8 pct in 8 zirconium and 4.8 pct in a zirconium. An X-ray study of nitrided materials was made in the range 6 to 13 wt pct N region because serious nitrogen losses were experienced when attempts were made to arc melt these high nitrogen alloys. PHASE relationships in the Zr-N system have been determined. Due to the inability to retain nitrogen in nitrogen-rich alloys subjected to arc melting, definitive work was possible only in the range 0 to 6 wt pct (0 to 30 atomic pct) N. Sufficient complementary X-ray work was done to permit construction of the binary phase diagram up to 13.3 wt pct (50 atomic pct) N (ZrN). Small ingots were prepared by arc melting master alloys with enough zirconium to produce an alloy of the desired composition. Following pretreatment, alloys were annealed at temperature levels between 600" and 2020°C. Determination of the phase boundaries was then accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to corroborate solidus curves, and X-ray diffraction was employed to study the nitrogen-rich region of the a + ZrN phase field. Materials Westinghouse Grade 1 iodide zirconium crystal bar served as the base material for this investigation. The as-received bars were lightly sandblasted, pickled in a 20 pct HN0-5 pct HF aqueous solution, rinsed in water and acetone, and dried. They were rolled to about 1/32 in. strip and acid-pickled, followed by water and then acetone rinses. The material was sheared to approximately 1/4 in. squares, cleaned with acetone, and stored for use. Pure zirconium nitride is not commercially available, according to correspondence with possible suppliers. A literature survey indicated that nitrogen may be introduced into zirconium metal by passing nitrogen or ammonia gas over zirconium at an elevated temperature. After considerable experimentation, a train was devised whereby high quality nitrogen was passed through a series of bubblers to remove the last traces of oxygen, through an H,SO, bubbler and a cold trap to remove moisture, and finally over zirconium within a resistance furnace. Hand-picked Bureau of Mines magnesium-reduced zirconium sponge proved more amenable to nitriding than the crystal bar. The nitrogen used was extra pure gas purchased from Linde Air Products Co. The first two bubblers through which the gas was passed contained a solution suggested by L. F. Fieser" as being ideal for removing the last traces of oxygen from nitrogen. The solution contains 20 g KOH, 2 g sodium-anthraquinone ,9-sulphonate, and 15 g NaHSO, dissolved in 100 ml water. It is blood-red and turns brown when contaminated with oxygen. A saturated lead acetate solution, next in the series of bubblers, removed any H2S which might have formed in the 0, removal stage. An H,SO, bubbler and cold trap removed moisture before the nitrogen was passed over the zirconium. The zirconium was contained in a stainless steel screen within a Vycor or quartz tube in a resistance furnace. Unreacted nitrogen passed out of the system through a mercury bubbler. A nitriding run was performed in the following manner: Zirconium was placed in the screen within the furnace tube. The unit was assembled, suitably clamped off, and evacuated to remove the air and moisture within the tube and that trapped by the zirconium sponge. The unit was flushed with nitrogen and evacuated twice. After nitrogen was allowed to pass over the zirconium for about 30 min, the furnace was turned on; several hours were required to reach temperature. The reaction was allowed to continue at temperature for about 4 hr and the screen was then withdrawn from the hot zone of the furnace by means of a Nichrome or Kanthal rod. The screen and its contents were allowed to cool at the end of the tube and were then removed. At 800°C no more than about 5 pct N could be introduced into the sponge zirconium. This material was designated M-1 (master alloy No. 1) and reserved for the preparation of alloys in the dilute nitrogen region. A second set of experiments was conducted at 1000°C; no more than 7.2 pct N could be introduced into the zirconium at this temperature. Enough material (M-2) of this nitrogen content was prepared to produce a second set of alloys to complement the first and to provide alloys in the 0 to 6 wt pct N range. It was hoped that a diffusion anneal plus a re-nitriding might yield a material of higher nitrogen content. The material containing about 7 pct N was therefore given a homogenization treatment at 1000°C for 6 hr under an argon atmosphere. It was

Jan 1, 1957

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report' prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers' of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961

By A. A. Smith, J. S. Smart, A. J. Phillips

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By A. J. Phillips, A. A. Smith, J. S. Smart

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is largely due to the economic advantages such systems frequently exhibit when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection.1 The main disadvantages of a pneumatic system are the greater horsepower required per unit weight of material conveyed, material limits in abrasiveness, and density. In addition, material breakage tends to increase at changes of direction and at any obstruction such as that caused by the imperfect butting of two pipe sections in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 lb per cu ft tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 lb and 20 lb per cu ft can be handled with fewer problems, but flow rate is hard to predict. The 20-60 lb per cu ft range offers best results, whereas materials of over 60 Ib per cu ft tend to drop out of the air stream and settle in the pipeline unless careful pro- visions are made to prevent this.2

Jan 5, 1968

By J. W. Smith

Our continuous search for underground productivity improvements has been brought about by the diminishing ore grades in existing underground mines. The need for more efficient mining methods is a result of the economic problems facing our industry today, and this has caused us to evaluate underground haulage methods which have traditionally been the "bottleneck" in the flow of material from the ore in the natural state to the surface processing facility of any underground mining operation. Small improvements in the face haulage systems have yielded much greater benefits as they relate to overall mine productivity so it's only natural that we are all concerned with the best method of moving ore from the face to the main line haulage. In a recent paper titled "Underground Haulage Trucks - Gaining Momentum Worldwide", Richard A. Thomas concludes that the use of trucks to haul ores in underground mines is on the increase spurred by the convergence of a number of technology advances and economic realities. Perhaps the most important stimulus for the growth of trackless haulage is the high degree of haulage flexibility in underground operations. On the economic side, the demand for higher productivity from underground mines has resulted in larger physical dimensions of haulage roads, that is, higher backs and wider drifts to provide more room for high capacity haulage units. In the process of determining the most effective type of equipment for haulage, the power source must be a major consideration. For the purpose of this paper, we will limit the comparison to rubber-tired trackless haulage vehicles and not try to make a comparison between rubber-tired haulage, continuous haulage systems and rail-mounted haulage. Cost is perhaps the only really measurable factor when making a comparison between electric and diesel haulage. You will find that some costs will be very well defined in absolute terms. In other areas of comparison, cost can be fairly well estimated, and yet in still others, the costs are totally arbitrary. Let's take a look at some of the cost considerations. (Figure 1) first of all, is the initial cost of the equipment. This capital cost quite often is a determining factor in the type of haulage vehicle to be selected, yet this initial cost is perhaps the most insignificant of all costs when evaluating an operation over the long term. Of much greater concern, is the cost of maintenance. This cost will often run three times the original capital investment during the life of a single piece of haulage equipment. This factor can include rebuild to extend the life of the original capital investment, but certainly includes the labor and materials necessary, plus the inventory to keep the equipment in good repair. Perhaps one cost which is now playing an even greater role in the rubber-tired haulage operation, is the cost of fuel. Conoco has recently come up with some rough estimates which indicate that diesel fuel will cost an average of three times the equivalent kilowatt output in direct electric power. Diesel fuel is almost twice the cost of stored electric power. (This of course relates to the efficiencies of charging and recovery of power from lead acid storage cells.) These particular figures of course will vary from one area to another but I think that there is enough significance here to certainly warrant the further study of fuel costs for each particular area or mine. Another cost is breakdown expense. This must be treated differently from maintenance costs because a potentially larger expense is involved, more than just parts and labor. Now we have to deal with the cost of lost production time, which can have a much greater overall effect. Mine plan economics are another cost consideration where we can't make a comparison without looking at specifics. Here you must look at the movement of power centers vs. the flexibility and freedom of movement of vehicles. The determination must be made as to what types of equipment will fit into any predetermined mine plan and if a change in the planned roadway dimensions for the mine plan itself would be more economical so that more efficient type of equipment could be utilized. Finally, two of the most important aspects to be considered with potential ramifications far beyond what we have mentioned previously, is the cost of health and safety, which is really the cost of meeting current and future government regulations, reasonable or otherwise. And of course, when making any consideration here it is impossible to come up with anything more than an educated guess on the cost of meeting the new regulations. Now let's take a look at some of the advantages of diesel vehicles as well as advantages offered by electric vehicles, both battery and cable powered versions (Figure 2). Much of the data used in this comparison is based on experience with three vehicles manufactured by Jeffrey Mining Machinery Division, Dresser Industries. Jeffrey manufactures all three types, each with approximately a 15-ton capacity, even though few of these Jeffrey vehicles are used in uranium mining operations. Much of our experience comes from the 4114 diesel powered RAMCAR which is a 4-wheel drive, articulated steering,vehicle powered by a Caterpillar 3306NA engine and using a powershift transmission. This will be compared with the performance of the Jeffrey 404H battery powered RAMCAR with articulated steering which utilizes a separate 35 HP DC drive motor on each of two wheels with solid-state speed controls, and the final comparison will be made on the Jeffrey 4015 cable-reel shuttle car which is powered by two 60 HP constant

Jan 1, 1982

By L. A. Bromley, R. L. McKisson

A high temperature calorimeter designed for use up to 1500°K is described and the theory of its operation presented. This calorimeter was used to measure the heats of formation of Na-Sn alloys ranging in composition from tin to Na2Sn. The values tend to support those reported by Kubaschewski and Seith. ONE method of obtaining the heat of formation of an alloy is to measure the heat of mixing of the elements at high temperature. The principal advantage of this method is that the desired quantity is measured directly, while in conventional room temperature methods the differences of the heats of solution of the elements and the alloy in a suitable solvent are measured. A method of improving the accuracy of the high temperature measurements, when the precision of the measurement is lower than that of the heat capacity values for the elements, is to add one component at room temperature to the other at the high temperature, so that part of the heat of reaction is dissipated in heating the cold component to the high temperature. Thus, only a fraction of the heat of reaction is measured, and a result of higher precision is obtained. The limitations of the high temperature technique are that volatile systems cannot be studied, and that many alloys melt at temperatures higher than those at which the calorimetric apparatus operates readily. Nevertheless, a calorimeter operating at 1500°K would be useful in investigating many of the lower melting alloy systems and the low melting mixed oxide systems. A unit designed for these applications was built and is described here. The Na-Sn system was chosen for investigation because the temperature involved, 880°K, would adequately test the operation of the calorimeter. Further, the data reported in the literature for the various alloys of sodium and tin differ markedly, and it was hoped that this investigation would help to fix the values of the heats of formation in this system. Design of Apparatus A detailed discussion of the considerations involved in the calorimeter design is given by Mc-Kisson and Bromley,' and a brief summary follows. Fig. 1 shows a sectional view of the calorimeter. The inner graphite chamber is maintained at constant temperature by means of the circulating molten tin bath in which it is submerged. The tin is contained in a graphite vat. This unit comprises a thermostat whose heat capacity is about 7000 cal per "C. The main heating element consists of a machined graphite spiral with a room temperature resistance of about 1/2 ohm. These parts are separated from the powdered carbon external insulation by the cage, a cylindrical graphite chamber. The electrical insulators and separators, the auxiliary heater spool, and the loading tube liner are made of sintered alumina. The tin vat stirrers, the sample stir-rer, the melt thermocouple well, and the power leads are made of molybdenum. The auxiliary heater is wound with molybdenum wire and serves to compensate for the heat loss up the loading tube. All of the individual components in the high temperature region of the calorimeter will withstand at least 2000°K, and the various contacting materials should easily withstand 1500°K. The external container for the insulating carbon powder is a copper shell upon which copper tubes are soldered to serve as cooling coils.

Jan 1, 1953

By Leason Adams

THE thermocouple as a device for the measurement of temperature is rivaled only by the platinum-resistance thermometer. Both instruments are capable of the highest precision, but the thermocouple, on account of its cheapness, ease of construction, and small cross-section, is finding a continually widening field of usefulness for industrial control as well as for laboratory measurements. Formerly, the thermocouple was subject to two disadvantages: errors due to lack of homogeneity of the metal and the labor involved in the interpolation between fixed points on the temperature scale. Former publications from the Geo-physical Laboratory have described the methods' for the selection and testing of thermocouple wire and have presented standard calibration curves2 for platinum-platinrhodiun and copper-constantan couples, so that the most important objections to the thermocouple as a precision thermometer have been removed. The calibration tables published in 1914 covered the range 0-1755° for the platinum-platinrhodium couple and 0-350° for copper-constantan. It has seemed desirable to extend the table for copper-constantan to -200 and also to include a table for the Hoskins thermocouple. Accordingly, in this paper, the new tables are presented, together with a brief explanation of their use; and, finally, certain diagrams and a paragraph on "cold-junction corrections" are given. Standard Calibration Tables.-In Fig. 1, which illustrates how the electromotive force (e.m.f.) of each of the three couples varies with the temperature, the temperatures of one junction are plotted as abscissas and the corresponding thermo-e.m.f.'s as ordinates. The second junction of the couple is supposed to be at 0°; the curves, therefore, pass through

Jan 9, 1919

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By William Priestley

IN THE manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and elastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungsten, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured-by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. DESIGN OF GUN FORGINGS In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun are made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The elastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge.

Jan 12, 1921

By C. P. Miller

In order to determine the usefulness of geochemical and biogeochemical prospecting for nickel, ten localities representing several types of nickel occurrences were selected as sites from which to collect plant and soil samples. This report covers the investigations in two of the areas. After a brief geologic description of the areas, the author presents details of the experimental tests and resulting data. Conclusions drawn from the studies led to several general guides for further prospecting. In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about three years ago, approximately ten localities, representing several different types of nickel occurrences, were sampled and about 1500 samples of plant and soil were collected. This report will cover briefly the data and results for two areas, and a summary of guides for prospecting. DESCRIPTION OF AREAS SAMPLED One locality is the Red Flats nickel prospect in Curry County, Ore., about six miles southeast of Goldbeach, and the other is the Little Rocky Creek prospect in Stillwater County, southcentral Montana, just southeast of the Benbow chromite mine. The Oregon area is a lateritic-type nickel deposit formed on a nickel-rich serpentinite peridotite complex, similar to the Josephine intrusion in southwestern Oregon. The Montana area is a nickel prospect in norite, peridotite, and related rocks of the Stillwater igneous complex. The Stillwater complex is a series of layered basic and ultrabasic rocks, with a layer of norite-gabbro at the base and a series of peridotites and gabbros above. The nickel in the Oregon deposit occurs in both the peridotite and the overlying soil. A deep lateritic soil is developed locally on the peridotite and serpentinite and constitutes the ore. The average nickel content of the lateritic soil is less than 1 pct, whereas the nickel content of the weathered peridotite is about 1 to 1.5 pct. The nickel occurs as garnierite (Mg, Fe, Ni, Mn)3 (OH)4 (SiA1)2O5 in the soil and in the olivine and pyroxene in the peridotite where it probably substitutes for Fe2+ or Mg2+ in the silicate lattices. Nickel is found in three distinct ways in the Still-water rocks: 1) it is in the olivine and pyroxene minerals in norite, harzburgite, etc.; 2) it occurs as widely disseminated grains of pentlandite-pyr-rhotite, which tend to be concentrated in the lower norite band; and 3) it occurs as discrete bodies of pentlandite-pyrrhotite and chalcopyrite which are localized in the norite zone, close to the contact with the underlying rocks. The nickel content of the norite is probably less than 1 pct, and the nickel content of the pods and lenses within the norite is about 1 pct. PROSPECTING APPROACH Although the areas are different geologically, the approach in prospecting them is fundamentally the same. The procedure is twofold: 1) a rapid reconnaissance survey to outline an area of high nickel content, and 2) a more detailed survey to outline zones of possible ore grade within the area of high nickel. The possible ore at Red Flats is concentrated in the lateritic soil, whereas at Little Rocky Creek it is in the sulfide pods. Both types are surrounded by an area of relatively high nickel content. CHEMICAL ANALYSIS Chemical analyses of nickel were made by a di-methylglyoxime colorimetric test, similar to the standard test for nickel, utilizing concentrated sul-furic acid for extraction. The lower limit of detection for nickel in soil by the method used was about 10 ppm and for nickel in plants about 5 ppm. The relative deviation was about 25 pct. SOIL PROSPECTING General Statements: A summary of the approximate average parts per million of nickel in soil, as compiled from the literature and from my study, is given in Table I. Selected references are given at the end of the paper. Few of the investigators reported the type of extraction or analysis, so the data given may not be strictly comparable to mine, which were made with a sulfuric acid extraction. Any nickel concentration greater than these average values might be considered anomalous, although each area must be studied in relation to the surrounding rocks. Method of Soil Sampling: The soil samples were taken in a zone from 1 in. to 1 ft below the humus layer, and within a 15-ft radius around a station.

Jan 1, 1961

By William M. Kester

INTRODUCTION The Coal Research Bureau of the School of Mines at West Virginia University is presently conducting laboratory-scale tests to determine the technical feasibility of beneficiating pulverized coal and coal fines with high-intensity electromagnetic fields. Interest in magnetic processes for cleaning fine coals was stimulated by results obtained by Yurovsky, et a1 in 1958.1 This work, while not new in concept,2,3 indicated that pulverized coal which had been thermally treated in a rotary drum in the presence of superheated steam and air underwent thermo- chemical reactions. Films of the ferromagnetic minerals magnetite (Fe2O3), hematite (Fe3O4), and pyrrhotite (FeS[3]) were reported to be formed on the surfaces of the pyrite grains associated with fine coal during the foregoing treatment at temperatures ranging from 120 to 360°C. After thermal treatment the coal was magnetically separated in an experimental magnetic device having a field strength of 10,000 oersteds.

Jan 5, 1965

By Eugene A. Stephenson

THE year 1935 is noteworthy for the superior legislative measures passed by several states. Sincere efforts have been made to establish equity between the various producing tracts in oil and gas fields. Outstanding legislative measures include the New Mexico law, known as Senate Bill No. 79, approved on Feb. 23; the Oklahoma law on April 22; the Texas law on April 30; and the Kansas law, which became effective July 1. Primarily designed to prevent waste, but more or less the direct out- growth of the current excess of potential oil and gas production, these statutes fall in the class of "Proration Laws."

Jan 1, 1935

By D. de Fontaine

A convolution procedure is described for obtaining an analytical expression for the composition profiles of solute concentration:; in binary solid solutions. The free energy of solutions containing such compositional inhomogeneities can then be evaluated and the stability of spherically symmetric clusters (G.P. zones, for short) us a function of their radii and central compositions can be studied accordingly. Two characteristic zone radii are defined: the minimum radius (RM) corresponding to the smallest zone for which growth is energetically favored over dissolution, and the critical radius RK) corresponding to zones associated with the minimum work of formation. The values of RM and RK coincide at the two classical limits of nucleation and growth and spinodal decomposition. As the spinodal is approached, however, RM and RK diverge increasingly and it is proposed that the initial] decomposition morphology is governed more closely by the minimum, rather than by the critical radius since the former possesses no singularity within the m eta stable phase boundary. Reversion is briefly discussed in the light of the foregoing and it is shown that a set of reversion temperatures located between the coherent miscibility gap and the coherent spinodal must correspond to a given distribution of low temperature zones. SINCE the early works of Guinier1 and preston,2 the kinetics and morphology of GP zones have been studied extensively, see Ref. 3, for example, for a recent review. Nevertheless, a completely satisfying theoretical treatment of the decomposition of meta-stable or unstable binary solid solutions is still lacking due to the almost unsurmountable mathematical difficulties that one encounters in attempting to solve the pertinent diffusion equation which, in principle, describes the whole process. This equation, first derived by Cahn for the initial stages of spinodal decomposition,4 is a nonlinear partial differential equation of the fourth order in anisotropic space, a general analytical solution of which is completely out of the question. From this equation, some prediction can be made, however, concerning the later stages of spinodal decomposition5 and a recent numerical solution6 of the equation in the case of one- and two-dimensional composition modulations of a solid solution inside the spinodal has led to the following considerations: the sinusoidal morphology7 is to be expected only for solutions of average composition c, located near the center of the coherent miscibility gap.8 For solutions with co closer to the spinodal decomposition, depleted shell zones9 should constitute the first recognizable decomposition product, later evolving to iso- lated, enriched preprecipitates in a uniformly depleted matrix as this must, in all cases, constitute the final metastable morphology, barring, of course, loss of coherency and change in crystal structure. In agreement with the qualitative description of Bonfiglioli and Guinier,l0 it thus appears that the various models discussed by previous authors are, in fact, idealized successive stages of the general decomposition process. Unfortunately, corresponding calculations for a solid solution outside the spinodal are not yet available because of two additional difficulties: it is essential that the diffusion equation be solved in three-dimensional space, and furthermore, one must include in the equation an appropriate "source term" describing the statistics of the creation of composition fluctuations required to trigger the nucleation events. At present, a general treatment of this problem does not appear to be tractable. Nevertheless, by using a modelistic approach, i.e., by selecting a priori certain composition variation profiles and by evaluating their associated free energies, one can draw certain conclusions relative to the stability of these isolated composition modulations or "zones", both outside and inside the spinodal. This is the object of the present investigation. THEORY We shall now describe a standard four-parameter spherically symmetric GP zone, evaluate its free energy according to the Cahn and Hilliard11 formula (Eq. [5], below), and plot the corresponding energy surfaces as a function of zone amplitude and radius as

Jan 1, 1970

By G. E. Johnson

The problem of efficient reclamation of zinc base die cast scrap became interesting early in 1930. Die Cast Metal, as referred to in this paper, is a zinc base alloy with various proportions of aluminum, copper, magnesium, antimony and tin. Many attempts were made to work out some means of reclaiming the discarded die cast metal for re-use as new die cast metal. Difficulties in such reclamation were attributable to contamination by lead and tin from solder, chromium and nickel from electroplated coatings, and iron from iron inserts. This paper relates the experiments that led to the development of a specialized muffle furnace for the treatment of zinc base die cast scrap for the production of zinc oxide and zinc, and describes the development of the muffle furnace and the equipment now used commercially for these purposes. The Eagle-Picher Co. acquired all patent rights&apos; for these developments from the International Smelting and Refining Co. in connection with their purchase of the East Chicago Plant. Zinc Base Serap Situation About 1935, the die cast scrap situation became increasingly acute for scrap dealers. This scrap was accumulating from dismantling automobiles and household appliances which contained die cast parts. Efforts to find an outlet for this type of scrap were intensified. The International Smelting and Refining Co. began to study the possibilities of a commercial process for the recovery of values from die cast scrap. At that time most of the die cast metal reclaimed was melted down in small kettles of from one to five tons capacity, the iron inserts being removed by skimming. The dross was skimmed off and disposed of as a zinc dross. The drossed metal was cast into slabs and was given the trade name "die cast slabs.". Distribution of the products produced by melting die cast scrap in kettles is shown in Table 1. American Process Experiments A method considered for the production of zinc oxide from die cast scrap was an adaption of the standard American Process of zinc oxide manufacture. Thus some die cast scrap was mixed with oxidized zinc materials and charged to Wetherill grates. The zinc oxidized to zinc oxide but, while the aluminum and copper largely remained in the residue, the color of the zinc oxide produced was impaired by copper contamination. As the proportion of die cast scrap was increased, liquation took place; that is, the metal trickled through the charge then solidified in the openings of the grates. French Process Experiments Several hundred tons of die cast scrap were purchased for test purposes and converted into die cast slabs. These slabs were charged into a French Process (horizontal retort) zinc oxide furnace with some electrolytic zinc. A satisfactory grade of zinc oxide was not produced. Distillation in Belgian Retorts It was then decided that, rather than attempt to use scrap die cast metal or scrap zinc for the production of zinc oxide, it would be advisable to redistill the die cast slab metal in a Belgian retort furnace. The opportunity to do so was provided by the closing of the zinc smelter of the Illinois Zinc Co. at Peru, Ill. Arrangements were made for the operation of a Belgian retort furnace for such redistillation purposes. The results of this experiment are summarized in Table 2.

Jan 1, 1950

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923