Search Documents

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

Polluted air and water, despoiled land and excessive noise are the unwelcome results of the population growth and a rising standard of living. The consumption of goods and services, including metal products and minerals, by all people is increasing so rapidly that civilization is in danger of destroying the environment in which it lives. This is true because every human activity affects the environment, whether it is air, water or land. While E. F. Osborn, director, U.S. Bureau of Mines, says . . . "some members of the mineral industry are reluctant to recognize environmental demands" . . . William T. Pecora Under Secretary of the U.S. Department of the Interior.. . says that, "to maintain levels of resource development and environmental quality needed to satisfy our affluence, we must trade off values rather than turn off troublesome operations." What it seems to boil down to is how much control of its operations is the mineral industry willing to accept-internal policing or strict government control? The answer lies in how well the mineral industry maintains a balance between mineral development and environmental quality.

Jan 1, 1971

The following is an incomplete list of members and guests who called at Institute headquarters between Nov. 10 and Dec. 10, 1917. Harlan H. Bradt, Duluth, Minn. Lt. Geo. H. Morgan. Albert Burch, San Francisco, Cal. F. W. Osborn, Ajo, Ariz. J. A. Daniel, Institute of Mining & Metal- J. C. Ray, 2d Lt., 0. M. C., N. A. lurgy, London. A. E. Ring, Creede, Colo. Martin Fishback, Benson, Ariz. Geo. B. Rodgers, Dobbs Ferry, N. Y. E. L. Foucar, San Francisco, Cal. Forest Rutherford, Pueblo, Colo. I. A. L. Henderson, Institute of Mining & J. G. Scrugham, Reno, Nev. Metallurgy, London. A. F. Shurick, Forest Hills, L. I., N. Y. Jerome A. Hilbert, Santa Monica, Cal. Arthur C. Spencer, Washington, D. C. B. B. Hood, Chrome, N. J. Robert C. Sticht, Mt. Lyell, Tasmania. J. C. Hoyt, Jerome, Ariz. A. Perry Thompson, San Francisco, Cal. A. F. Kennedy, Duluth, Minn. J. B. Tyrrell, Toronto, Canada. Paul S. King, Wilmington, Del. Thor. Warner, Phoenix, Ariz. Alfred C. Levis, Golden, Colo. S. F. Wellman, Cleveland, 0. A. F. Lucas, Washington, D. C. Gardner F. Williams, San Francisco, Cal. B. E. McKechnie, Sharon, Pa. W. G. Woolf, Salt Lake City, Utah.' A. N. Mackay, Barranquilla, Colombia. C. W. Merrill, San Francisco, Cal. P. G. Beckett expects to be located in New York for some time, and may be addressed care of the Phelps, Dodge Corporation at 99 John Street. Corey C. Brayton and E. R. Richards have temporarily closed their San Francisco offices in order to give more time to their operations at Midvale, Utah.

Jan 1, 1918

By Serge L. Delinois

President Kennedy said that before 1970 this country will send a man to the Moon and get him back on Earth safely. Today, no one doubts that his promise will become reality. He who asks "What, then, is next for us in space?" is no longer considered a dreamer. And one of the very first things he discovers in trying to answer this question is that in whatever does come next, geologists and mining engineers will play a prominent role. This will be true not only in the conquest of the Moon, but also in that of the whole solar system. After 1970, it is very likely that a permanent lunar camp will be established. This beachhead, supplied entirely from Earth, in the beginning, will gradually develop into a research complex where virtually all scientific disciplines are investigated.

Jan 1, 1966

By C. B. Alcock, R. G. Hudson

Sulfur pressure measurements above FeS in equilibrium with iron have been carried out by the Knudsen orifice method. A comparison is made of the weight loss of the cell per unit time obtained in the above experiments, that calculated from Richardson and Alcock's measurements of the S2 pressure above FeS in equilibrium with iron, and the dissociation constant for diatomic sulfur from spectroscopic and thermal data. EXTENSIVE equilibrium measurements have been made to determine the sulfur potentials of a great many systems of metallurgical interest.' In order to confirm their reliability, to supply data which may be of use in further thermodynamic calculations, and to establish the reliability of the Knudsen orifice in obtaining accurate thermodynamic values at high temperatures, the present investigation on the pressure of the gaseous species above FeS in equilibrium with iron has been carried out. The Knudsen orifice method has been used for these pressure measurements. Experimental The apparatus and general technique for this investigation are the same as that reported for the determination of the vapor pressure of silver.' To reduce the residual gas pressure in the evacuated chamber, a titanium getter, maintained at run temperature, was introducbed. Several types of Knudsen cells were used—platinum, zircon, and fused silica. The orifice in the zircon cell was fashioned with a small diamond wheel. The same precautions were used in this investigation as were employed in the work on Mo2S2.3 The FeS-Fe mixture was prepared by heating a sample of pure FeS,, supplied by K. K. Kelley of the Bureau of Mines, with excess iron powder, cp grade, obtained from the Fisher Scientific Co. These two substances were heated in a closed Armco iron crucible at 960°C, held in a vacuum of less than 10" mm Hg for 24 hr. The mass was then removed from the cell and ground in an agate mortar. In this form it was charged to the various Knudsen cells. Heating the Knudsen cell for an additional two days was sufficient to obtain constant rates of weight loss of the cell. The data obtained in this investigation are recorded in Table I. To establish whether or not a sulfide of iron is volatile at these temperatures, 0.7646 g of the FeS-Fe mixture, described above and containing 69.2 pet Fe, was placed in the zircon Knudsen cell. Run Nos. 103 to 109 were performed on it. After the completion of these runs, the total amount of iron left in the cell was obtained by chemical analysis. It contained 0.537 g Fe, compared to 0.529 g in the original charge. Thus, there was an apparent gain in iron of 1.5 pet. This is attributed to unknown experimental error, and the conclusion is that no sulfide of iron is volatile. The vapor pressure of pure iron4 is about one thousandth that of the sulfur pressure' at these temperatures. The vapor pressure of iron inside the Knudsen cell will be almost exactly that of pure iron, since in the iron-rich phase the percentage of sulfur is of the order of 0.025 pet.At this low percentage of sulfur Henry's law is probably obeyed by the sulfur. Thus, the iron will obey Raoult's law. In any event, the vapor pressure of iron will be lower than that of pure iron and, since the vapor pressure of pure iron is negligible compared to the pressure of sulfur, the weight loss of the cell due to the vaporization of iron should be negligible. Since neither iron nor FeS is volatile to an appreciable extent, the total weight loss of the cell must be due to the vaporization of sulfur. Discussion and Calculations On the assumption that S, is the only gaseous species present in appreciable quantity, its pressure

Jan 1, 1957

By Vince Poxleitner, John Delaney

Introduction In the mining industry, comminution typically begins in the mine with a blast of explosive to break rock so that it can be handled by the avail- able equipment. Though the breaking of the rock is essential for material handling in the mine and plant, this is not the only reason for ore reduction in the mineral industry. Comminution is primarily required to liberate minerals from ore so that they can be concentrated into valuable products or to prepare minerals, such as talc, for market as mined. The size of the equipment used for comminution ranges from small to massive. Regardless of equipment size, the power required to reduce the rock is a major expense. Years ago, mineral deposits could be mined more selectively and required less grinding to produce saleable products. However, as richer deposits were depleted, it has become necessary to mine low-grade deposits, with the valuables dispersed throughout the rock. Comminution equipment evolved in physical size and capacities to meet the new mine and process requirements. A modern, modestly sized mining operation, with a capacity of 25.000 TPD may use crushers two stories high weighing over a million pounds, SAG mills 36 feet in diameter driven by dual motors putting out 10.000 horse- power, and ball mills over 16 feet in diameter . Because of the increasing size and weight of modern equipment, the builder is faced with the problems of erecting massive foundations and field assembling equipment on these foundations. As equipment costs and plant construction costs increase, builders are finding that owners are asking for more detailed progress and cost data. Comminution construction projects are generally classified as grass roots plants or expansions or modifications to existing plants. It is estimated that 60-702 of the jobs involve existing plants. Today ' s costs for construction of small, new comminution plants can reach tens of millions of dollars; larger plants can cost hundreds of millions of dollars. Modifications, on the other hand, usually run from a few thousand to several million dollars. Though many problems are common to the construction of both new plants

Jan 1, 1982

By Harold A. Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand- book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By C. J. Osborn

The temperature dependence of the free energies of formation of metallurgically important oxides, sulphides, chlorides, carbonates and sulphates is presented graphically, whereby the task of deriving practical metallurgical information is greatly simplified. The diagrams have been revised according to the latest available thermodynamic data. WHILE it is true that much careful investiga-tional work remains to be done, there are already available in the literature sufficient thermo-dynamic data to enable the metallurgist to predict with reasonable confidence the equilibrium conditions to be expected in most important, and potentially important, metallurgical reactions. In this connection, the careful, critical compilations of K. K. Kelley and his collaborators in numerous U. S. Bureau of Mines Bulletins are particularly valuable. However, the translation of reliable thermo-dynamic data into metallurgical language unfortunately involves lengthy manipulations of the cumbersome formulas which can be set up from heat of formation, entropy, and heat capacity data. Many years ago, Kelley20 predicted that thermo-dynamic calculations would be made in the future "with the aid of free energy, heat content, and entropy tables, rather than by means of the algebraic methods employed at present", and where such tables are available they greatly simplify the task of deriving practical metallurgical information. However, in addition to these tables, there are also available one or two reliable graphical presentations, particularly of free energy data, which may be used in the same way as the tables, but which have the added advantages that interpolation is never necessary, and that the behavior of different metals or compounds may be compared at a glance. Some years ago Professor Robert Lepsoe, Head of the Department of Metallurgy at Norways Institute of Technology (N.T.H.), began a compilation of curves showing the temperature dependence of the heat contents of the elements, and the heat contents and heats and free energies of formation of the common metallurgical compounds. With such a compilation, the thermal and free energy requirements of a reaction may be read from curves in a matter of seconds; and this statement applies not only to the formation of compounds from their elements, and to the reverse dissociation, but to any reaction involving substances whose thermodynamic properties are available. This follows from the fact that heats and free energies of formation are completely additive. For example, the free energy change associated with the chlorination of a metallic oxide at any temperature, T, is given by the free energy of formation of the chloride at temperature T minus that of the oxide also at T; both of these quantities may be read directly from curves of the type suggested above. Since this early, unpublished work of Lepsoe, both Ellingham7 and Richardson and Jeffes46 have

Jan 1, 1951

By Donald McLaughlin

INCREASING variety of interests among mining geologists is becoming more and more marked, as the frontier of their science and of its applications continues to expand. Each of the traditional lines of inquiry provides its crop of new and better defined problems, and answers to them are being found in far more precise terms than in the past as older uncertainties .are swept away with the sharper techniques and the even sharper ideas of modern geology. A glance over the assemblage of projects and publications in 1939 reveals conspicuous activity in many different parts of the front, such as the attack on the controversial question of the acid or alkaline character of ore-forming solutions, the place of mineral districts in the larger structural framework of continents, and the place of ore shoots in the local patterns of districts. Instructive comparisons are being made which cut across lines of older correlations or which reinforce them by pointing out heretofore ne-

Jan 1, 1940

By M. S. King, B. N. P. Paulsson

Four vertical boreholes in the vicinity of an electrical heater simulating a canister of nuclear waste in a granitic rock mass have been logged with an acoustic borehole sonde before and after thirteen months' heating. Excellent control of the structural geology and fractures present in the rock mass was provided by the considerable amount of oriented core recovered from the four boreholes used for acoustic logging and the large number of others used for a variety of rock mechanics instrumentation. Compressional and shear-wave velocities were measured as a function of stress on some twenty core samples, water-saturated and dry, which were recovered from the four acoustic logging boreholes. Further control was provided by a cross- hole acoustic monitoring program conducted before, during and after heating between the same four boreholes, and by measurements of acoustic velocities in an isolated block of granite in the same heater drift, which was subjected to an increase in temperature and to changes in uniaxial stress. It is concluded from the acoustic logging tests, taken in conjunction with the acoustic cross-hole and heated block experiments, that acoustic techniques: 1. Provide a means for locating and delineating systems of weakly- bonded or open fractures within the rock mass; 2. Provide a sensitive means for monitoring a rock mass for changes in moisture content or structural damage to the rock fabric induced by thermal or mechanical loading; 3. Together with the rock bulk density yield the elastic constants of the rock mass.

Jan 1, 1982

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By W. C. Merrill, P. G. Nahin, A. Grenall, R. S. Crog

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By H. F. Haller

COLUMBIA-SOUTHERN'S Barberton limestone mine, 8 miles southwest of Akron, Ohio, is a million-ton-per-year producer from a depth of over 2200 ft in a district where other underground mining at this depth is unknown. Mining extracts 46 of the top 51 ft from a formation of Devonian limestone discovered by drilling in the 1890's. The same drilling revealed extensive salt deposits below the lime- stone, which led to the location of the chemical plant at Barberton as a division of the Pittsburgh Plate Glass Co. in 1899. Soda ash was the principal product of the plant, and as production increased the demand for limestone increased. Columbia's first attempt to secure a reliable all-weather source of stone was the development of a quarry at Zanesville, Ohio, in 1919. Zanesville production eliminated some of the stock- piling required by the use of Michigan stone, avail- able only during the lake shipping season. Stone from some Zanesville horizons, however, was found to be more suitable for cement production than for soda ash, and rail transportation remained an important factor. As demand continued to increase, plans were made to develop the Barberton deposit.

Jan 12, 1954

By Hugh J. Leach, J. C. Van de Water

In open pit mining, as in other industries, it has I become necessary to improve operating efficiency in order to combat higher labor and supply costs. Moreover, orebodies are becoming leaner, pits are getting deeper, stripping ratios are increasing, and hauls are getting longer. There has been a steady increase in size, speed of operation, and reliability of the various machines involved in breaking, loading, and hauling ore. Changes have seldom been radical but are rather the result of steady improvement. Drilling: Notable advances have been made in the use of rotary drills and air powered percussion drills for blasthole drilling. Several hundred of these machines are now in use as replacements for churn drills in softer rocks such as limestone and shale. Their application to hard rocks such as iron ore and taconite is under current investigation, but in the Lake Superior iron mining district, open pit blast-hole drilling in ore has been accomplished almost exclusively by standard churn drilling. The only recent advance has been the use of larger machines drilling 9-in. holes. This has increased drilling speed somewhat and allowed wider hole spacing, with consequent cost reduction.

Feb 1, 1956

By AIME AIME

WEST TEXAS, New Mexico and Northern Mexico form one of the most interesting regions in America for geologists and mining men and are full of points of historical and human interest for others. Including as the region does, a representative portion of the high plateau of Mexico, the front range of the Rocky Mountains and the great down-dropping plains of Texas, there is variety as well as interest in the geological and mining problems there to be studied. Gold and silver mining were the pioneer industries and are yet of high rank in importance. Among the papers to be presented at the El Paso meeting of the Institute this month will be two dealing with silver mining and ore treatment at the Shafter mine in Texas, that most un- usual property which has for so many years been the largest mining enterprise in its region. West Texas is now better known for its petroleum and gas, and in another paper will be described the problems involved in uding natural gas for smelting at the well-known El Paso smelter of the American Smelting and Refining Co. In still other papers, presented at the session sponsored by the West Texas Geological Society and cooperating organizations, the general geology of the region, the potash and the sulfur deposits will be de- scribed. At El Paso the refineries of the great com- panics will be available for visits.

Jan 1, 1930

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By J. S. Marsh

JOSEPH PRIESTLEY prepared oxygen on Aug. 1, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance-as air-has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic- importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 SIGNIFICANCE OF HIGH-TEMPERATURE HEAT The principal 'function of the open-hearth furnace is to supply sufficient, high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy-and heat is energy is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature; which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon l is understood by dioxide and water vapor as reaction

Jan 1, 1948

By Joseph A. Holmes, Henry Kreisinger

At the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a con~mittee consisti~lg of 11. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr..J. K. Clement, physicist. The problem, essentially one of physical chemistry, is estremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of' the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. in volatile matter and from 40 to 75 per cent. of fixed combtistible. The greater part of the latter is burned on the grate: but the volatile combustible leaves the freshly-charsed coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible mill leave the furnace only partly burnecl, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven oft' per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 30 cu. ft., the burning mixture will stay in it,

Jan 1, 1911