Search Documents

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By Ernest Lilley

THE tin deposits of Cornwall appear to have been worked for at least 3000 years. Prior to the sixteenth century, the tin came exclusively from alluvial deposits. At that time, shallow pits or mines were started in the hill sections. Mining of copper seems to have begun at the same time, but does not appear to have been especially important until about 1700. From that time until the close of the nineteenth century, copper was of major importance. Lead, and to a lesser extent, other metals, such as antimony, iron and manganese, were produced in commercial quantities during the same period. With the opening of the eighteenth century carne increasing difficulties with water because of the increasing depth of the mines. Among the efforts made to overcome this difficulty was the construction of the "Great County Adit," begun in 1748, taking 20 years to complete, and with its branches having a length of 20 miles. Adits proved capable of handling-only a few of the water problems, and led to rapid adoption of the steam pumping engine in the latter part of the eighteenth century and the early part of the nineteenth. It was in this period that the Cornish pumping engine, still considered by Cornishmen to be the most satis-factory unit for handling large quantities of water, carne into existence. The development of a means of controlling the water made possible the opening up of a number of rich deposits where profitable work-ing was further assisted by numerous improvements in mining and milling machinery. During the middle of the past century, Cornwall, with an average yearly production of 10,000 tons of tin metal and an even slightly larger tonnage of copper, enjoyed a period of unprecedented prosperity. How-ever, the relatively high prices of both copper and tin served not only to encourage prospecting (and much speculation) in Cornwall, but also in other countries. The rapid development of copper mines in the United States, together with sudden impoverishment of the lodes with increasing depth in the greatest of the Cornish copper mines, brought the copper boom to an abrupt end, the production of copper at the close of the cen-tury being negligible in importance and being secured in large measure

Jan 1, 1932

By J. Alfred Berger, O. M. Katz

The Zv-Hf-H ternary system was studied between 500° and 900°C at pressures less than 1 atm of hydrogen gas between 1 and 60 at. pct H. A new and unique microgravimentric apparatus was used. Cizanges of slope on pressure-hydrogen composition isothernis delineated phase boundaries. These boundaries separatecl the three regions, a, 0, and y—so designated to correspond to the regions of the Zr-H binary system—from the multiphased areas between them. A eutectoidal decomposition was found with the ß region phase or phases decornposing into a lamellar product on quenching to rool ter,zperatuve. Reproducible decomposition-pressure hysteresis occilrved lnainly at lower hydrogen cornpositions and at lower temperatures across multiplzase vegions between a and 0 and a and y. Tire effects of hqfniur7z on the hydriding charactevistics of zirconiurrz weYe as follows: 1) stabilization of the a and y vegions while destabilizing the 0 region; 2) a/?preciable elevation of the decomposition pressrkres in the multiphase region between the a and /3 field; 3) ~nouenzent of the eutectoid reaction to high te~nperatures; 4) reduction in the total qiiantity of hydrogen absorbed under one atmospheve of Hz p7-essure; and 5) introduction of a split deconzposilion at the eiitectoiclal poinl in pa?? of the ternavy. Assuru~ptions based on an ir-2terstitial vandonl-solulion rtioclel 0.f hydrogen in metals slzowed that the bindit~g energy between solute sites prednnzinatecl at low /i?!dvogen concentrations. However, at high hydrogen contents the entropy was the predorninatlt factor in determining the stability of the Zr-Hf-H al1o.s. This was interpreted to mean a scarcity of filrtlzer itltevslilinl solute sites caused by hydrogen-hydvogen intet-actions in the metal lattice. INTEREST in the reaction of hydrogen with metals has increased in the past few years for the following reasons: 1) the formation or use of high hydrogen potential environments in nuclear reactors; 2) the reaction of hydrogen with alloys in nuclear reactors with the accompanying deleterious effects on the mechanical and corrosion properties; 3) the theoretical implications of thermodynamic data on the theory and rules of alloy formation in the metal-hydrogen systems; 4) the use of hydrogen-containing fuels in rocket engines; 5) the need for a process of making fine metal powders of high-melting reactive metals; and 6) the beneficial impregnation of superconducting alloys with hydrogen. In nuclear pressurized-water reactors, the problem exists of limiting the hydrogen pickup of zirconium alloys which are utilized as fuel cladding, heat shields, and support members. In general, zirconium alloys have good mechanical and corrosion-resistant properties in high-temperature water. However, hydrogen is absorbed from the corrosion reaction between metal and water, greatly accelerating the formation of the corrosion product ZrOz as well as mechanically embrittling the underlying metal. In addition, recent observations1 at zirconium to hafnium welds showed that secondary elements in zirconium can have an appreciable, and somewhat unexpected, effect on hydrogen absorption. This paper lists the thermochemical data in the range 500" to 900°C for the equilibrium reaction of four high-purity Zr-Hf alloys with hydrogen. Phase boundaries and thermodynamic functions are determined while the structural data will be presented in a future paper. In general, the Zr-Hf-H system approximates the well-known, eutectoidal, Zr-H diagram2,3 with modifications introduced through the behavior of hafnium.4,5 The Hf-H system,' published while this work was in progress, provided a consistent trend with the Zr-Hf-H data. PREPARATION OF Zr-Hf ALLOYS Table I presents a complete flow chart of the preparation procedure. The zirconium and hafnium crystal bars were completely immersed in high-purity kerosene and slowly cut into thin wafers. Wafers were then cold-sheared into approximately 1-g pieces, thoroughly cleaned, weighed, and inserted into the furnace. The alloys, B-2, B-4, B-6, and B-8, were then nonconsumable arc-melted under 500 mm of purified argon. Additional purification of the argon was accomplished by melting a large titanium button each time an alloy was re-melted or a different alloy melted. Each alloy button, which weighed 25 g, was remelted four times in an approach to complete homogeneity. Material losses were less than 0.02 wt pct. Alloy buttons were alternately cold-rolled and vacuum-annealed into 10- and 20-mil sheets. Table I1 gives the composition of the four alloys used. Very little elemental segregation existed be-

Jan 1, 1965

By Albert G. Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed.. Today, 'however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. DRILL TOOLS Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brinell hardness

Jan 1, 1935

By W. R. Hibbard

IN ref. 1, on the basis of tension and torsion experiments with single crystals of a brass, the values given in Table I were obtained for elastic coefficients. It was pointed out by Zener that the values for the 71.2 pct Cu were not satisfactory, since they resulted in a negative value for the bulk modulus, namely —4.17X1012 sq cm per dyne. In reevaluating the data of this investigation, it was determined that the reason for this negative bulk modulus lay in the extrapolation of the reciprocal Young's modulus to the zero value of the orientation function shown in Fig. 5 of ref. 1. This extrapolation was reevaluated by the method of least squares (50 pct probability) and a new value of the coefficient S,, was determined as 18.9220.42X 10M sq cm per dyne in lieu of the value originally reported of 18.82x10 sq cm per dyne. This new value of S, leads to a new value of S, of — 9.43 X101" sq cm per dyne. The values of the other coefficients are unchanged. results. This value compares with the value of 12.3X10 sq cm per dyne reported by Schmid and Boas? The new results are summarized in Table 11. These results follow similar qualitative trends, previously published,' relative to the effect of zinc content. However, the derived values of C11, C,, C,, and K are so sensitive to the uncertainty in the first decimal place of the S, values that they are probably not useful. This uncertainty must also apply to the previous results of Masima and Sachs," who obtained S, values from a similar extrapolation drawn wholly above their data points. Acknowledgments Advice and assistance on the statistical methods were obtained from R. W. Guard. The calculations were carried out by Miss E. Saacke.

Jan 1, 1958

By R. H. Doremus, E. F. Koch

The first carbide phase that precipitates at 120°C from a iron containing about 0.02 wt pct, C was studied with the electron microscope. In both strained and unstrained material the carbide particles appeared to form on the dislocations in the iron, in agreement with the results of the kinetic study in part II. The structure of the carbide was tentatively identified as an expanded a-iron lattice (body-centered tetragonal) with about 0.7 wt pct C. This phase appeared to be metastable and apparently transformed into cementite or epsilon carbide when the iron was over-aged. WhEN a iron containing less than about 0.025 wt pct C is quenched from 700°C to room temperature the carbon is retained in solid solution and precipitates out slowly with time. The morphology and structure of the precipitating phase are still in doubt, two different carbide phases, epsilon carbide and cementite, have been identified, but there is considerable disagreement about the time and temperature at which they appear.1-4 Epsilon carbide seems to form at lower temperatures than cementite, although one group of investigators4 found only the latter phase over a wide range of aging temperatures. Usually these two phases have been identified after aging times much longer than needed to drain the carbon from supersaturated solution, at least for aging temperatures below 200oC. The precipitated carbides have been observed with the electron microscope,'-5 but again most results have come from samples aged much longer than necessary to reduce the carbon concentration in solution to a low value. In this study the carbide phases were observed in earlier stages of precipitation with the electron microscope, in order to learn more about the shape, size, and distribution of the carbide particles. Samples strained small amounts before aging, as well as unstrained samples, were studied, and the structure of the carbide phase was tentatively identified. EXPERIMENTAL "Ferrovac E" vacuum-melted iron, from which the wires for kinetic studies were also made (Refs. 6 and 7 and the following paper) was used for this work. An analysis of this material is given in Table I; it agrees well with the manufacturer's values. The number of inclusions in the iron was very small, as can be seen in the optical micrograph in the following paper. Pieces of iron about 1 mm thick and 5 to 10 mm in diam were used for all the studies except for those in which the sample was strained before aging; then the specimen was a rod 3 to 6 mm in diam and 20 cm long. The samples were held at about 700°C in wet hydrogen for at least an hour to remove residual carbon and nitrogen, after which they were heated to 950" (in the y region) and cooled to room temperature in the furnace. This treatment gave an average grain diam of more than 1 mm, so that the effect of grain boundaries on the precipitation process was negligible. The samples were carburized at 710°C for about 2 hr in hydrogen that had passed over toluene held at -30°C; then they were rapidly quenched into water. From chemical analysis this treatment gave a carbon concentration of from 0.012 to 0.016 wt pct, which is less than the solubility of carbon at this temperature. After quenching, the samples were aged at 120 "C in an oil bath for vari-

Jan 1, 1961

By E. H. Erwin Gartner

The Rhenish lignite deposit in the Nordrhein-Westphalia province of the German Federal Republic covers an area on the left bank of the Rhine River of about 970 sq miles (Fig. 1). Here, in the Miocene era, some 20 million years ago a lignite seam was formed and later broken, through tectonic movements into several blocks, some thrown down into depths of over 1,500 ft. This deposit consists of a single seam, in places up to 300 ft thick, but averaging about 150 ft. In a few areas, it is split into as many as five seams, separated by barren strata. It contains about 60 billion tons (2000 lb/short ton) of lignite which, however, being relatively young geologically, has, because of approximately 60% moisture, 2 to 8% ash, and low sulfur, a net calorific value of 3,340 Btu. That calorific value increases, however, with rising thickness of the cap rock. About one-third of the yearly production of 90 to 100 million tons of raw lignites is converted into briquets. Raw lignite is pulverized and dried to about 18% water content and then pressed without binder into briquets under a pressure of about 14,000 psi. The briquets are being used primarily for residential heating; their sales, however, have been declining sharply since 1963. On the other hand, the volume of raw lignite used in steam power plants has been rising steadily and amounts at present (1968) to about two-thirds of the total production. Huge steam power plants, such as Frimmersdorf, shown in Fig. 2 (which, with an installed capacity of 2,600 MW [megawatt], represents the world's largest steam power plant) with a generating capacity of up to 300 MW per unit and a total installed capacity of over 6,000 MW, contribute about 26% of the total electric power production of the German Federal Republic.

Jan 1, 1969

By John Porter

THE requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet process and the dry.

Jan 1, 1925

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

OF the many categories into which scientific knowledge has been arbitrarily divided, the one that has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry1 provide ample material on the principles of this subject for the student of steelmaking processes; yet with- out exception those texts draw the greater part of their illustrative material from room-temperature data. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development but in the main those applications in which we are here interested can be ex- pressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent respectively the natural and the common logarithm of X. The two are related by In X = 2.303 log X. Logarithms may be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be, helpfu1. MATTER Innumerable forms of matter may be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas. Whenever such a change occurs there is a corresponding change in

Jan 1, 1951

By Dennis Peterson

INTRODUCTION The business arena has dramatically changed for most producers and consumers of commodities. International debt, currency shortages, political upheavals, etc., require corporations today to be sophisticated and flexible enough to change their purchasing and sales techniques in order to maximize returns. Many external factors, such as interest rates, trading partners, currency changes, and government edicts, can have an adverse effect on a company's bottom line. Totally out of a company's ability to control or predict, these. factors force the commodities based corporation to constantly re-evaluate its operating scope and domain. The principle of back-yard only operations and the laissez-faire with blinders style of management is no longer a viable way to run a business. The industrial world has been operating for the past 10 to 15 years as though there were no commodity nor raw material crisis. For developed countries the primary products sector has become marginal, whereas it was central in the first half of the century. A radical change in the method of doing business is necessary to offset a depression in the industrial economy. The risk of collapse may be heightened by a banking crisis caused by massive defaults on the part of commodity producing debtors, whether in the third world or in our own farm producing sector. The raw materials economy has become divergent with the industrial economy. This is a major change in the world economy with tremendous implications in both developed and developing countries for economic and social policies and economic theories. Basic competition issues, such as low labor costs, are likely to become less of an advantage in international trade. In developed countries these costs are going to account for a smaller portion of total costs. The total costs of automated processes are lower than those of traditional plants with low labor costs. Automation in the commodities sector eliminates the hidden but high cost of not processing at capacity created by poor quality, rejects and maintenance for product change-overs. The cost of capital will become increasingly important in international competition. Over the last ten years the U.S. has become the highest cost country in this area. Reversing the U.S. policy of high interest rates and costly equity capital should be a priority for management decision makers. In the rapid industrialization of this century, Japan developed by exporting raw materials, (principally, silk and tea), at steadily increasing prices. Germany developed by leap frogging into the high-tech industries, mainly in electricity, chemicals and optics. The United States did both. Both avenues are blocked for today's rapidly industrializing countries because (a) the deterioration of the terms of trade for primary products, and (b) it requires an infrastructure of knowledge and education far beyond the scope of a poor country. Many explanations exist for the explosion of international money flows. The shift from fixed to floating exchange rates in 1971 may have given initial impetus by inviting currency speculation. The surge in liquid funds flowing to petroleum producers after the oil shocks of 1973 and 1979 was definitely a major cause. There can be little doubt that the U.S. government deficit also played a big role. The American budget deficit has become a massive void, sucking in liquid funds from all over the world and making the U.S. the world's major debtor country. In reality, a trade and payments deficit is actually a loan from the seller of goods and services to the buyer, that is, to the U.S. From now on, the global ramifications of business will have to be treated in economic theory and business policy alike. Economic theory teaches that the comparative advantage factors of a real economy determines operative and financial policy. These comparisons -- labor costs, productivity, raw materials cost, energy costs,

Jan 1, 1990

By R. Kossowsky

BRIDGMAN has listed five possible transitions in bismuth at 25°C which were observed as volume changes. He was unable however to detect the last three transitions by electrical-resistivity changes. Kennedy and LaMori have verified the pressures at the Bi 1-11 and Bi 11-111 transitions. They suggested however that the 125-kbar transition previously reported by Bundy3 actually corresponds to the 90,000 kg per sq cm transition observed by Bridgman.1 Jura4 reported a well-defined drop in resistivity at 92 kbar obtained by a four-lead method. The Bi 111-IV and Bi IV-V transitions have not been reported in any of the above-mentioned references.'-' Bundy3 observed a small dent in the low-temperature boundary of the Bi Vll region which is consistent with the presence of a 111-IV boundary. Zeitlin and Bray-man5 were the only ones to report small but well-defined drops in resistance of bismuth at 44.0 and 63.8 kbar, corresponding to Bridgman's 111-IV and IV-V transitions, respectively. High-purity (99.99 pct) 0.020-in.-diam 0.5-in.-long bismuth wire was used to calibrate the Uniram tetra-hedral high-pressure apparatus used in the present work. The bismuth phase changes at 25°C were correlated with changes in electrical resistance as a function of pressure. The output of a sensitive bridge constructed of carbon resistors and kept at a constant temperature of ±°C during the measurements was fed to the Y axis of a MoseleyX-Y recorder and the X axis was used for time scans. Specimens were pressurized using a hydraulic press with maximum capacity of 200,000 lb. Load was applied in increments of 2000 lb and held for about 3 min. The resistance was recorded at the end of this time period. Good contact was established below 20,000 lb. Typical recorder charts are reproduced in Figs. 1 and 2 which show that resistance fluctuations were practically nil during each time scan. Well-defined discontinuities in resistance were observed at 58,000 and 82,000 lb, Fig. 1. Two small but definite "blips" are noticed at 92,000 and 122,000 lb, Fig. 2. At 156,000 lb another drop is observed which

Jan 1, 1967

By Kirtley F. Mather

FROM almost every point of view, petroleum was "strategic mineral number one" during the World War that ended in 1945. Even the spectacular advent of the atomic bomb in the final days of the conflict did not displace it from its position of prime importance, although within a few years uranium will almost certainly be the "number one" material in the minds of military strategists, if it is not even now in that position. But both as fuel and as raw material for chemical industries, petroleum will hold the center of the stage for many years to come. Hardly any other substance illustrates so fully the manner in which science and technology may be combined to achieve the utmost success in contributing to human efficiency and comfort. Fundamental to any understanding of the problems implied by my topic

Jan 1, 1948

By William Campbell

In the olden days the making of alloys was an art, and the secrete of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formulæ are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,' Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville7 on the Cu-Sn series and of Shepherd 8 on the

Jan 1, 1913

By L. H. Cadoff, L. M. Adelsberg

The layer growth method has been used to investigate the reaction kinetics of liquid titanium and hafnium with carbon and the [liq] - [liq + TiC] and [liq] - [liq + HfC] phase boundaries at temperatures above 1800°C. The equipment and experimental procedures used in this investigation are basically identical to those described in an earlier paper' on the Zr-C reaction. Temperature control, however, was improved significantly by connecting a Latronics Colo-Ratio automatic pyrometer and a controller to the power source. The subsequent temperature variations were ±10°C; previously ±20°C was obtained using manual controls. The absolute accuracy of the pyrometer, however, must be considered to be only ±40°C.* The spectrographic analyses of the materials used in this study are listed in Table I. The isothermal reactions of titanium (1800° to 2700°C) and hafnium (2300" to 3000°C) with carbon (graphite crucibles) resulted in the formation of carbon-saturated liquid metal and layers of Tic and HfC, respectively. The thicknesses of the carbide layers, determined from metallographic measurements at 100 times, as a function of carburization time and temperature are given in Figs. 1 and 2. At each temperature, parabolic growth behavior for these reactions was observed and could be expressed as x2 =Kpt, where X is scale thickness (corrected for heating and coolingL), Kp the parabolic growth constant, and t the isothermal carburization time. Values of Kp as a function of temperature for the carbides are shown in Fig. 3 and listed in Table 11. The growth constants are expressible as: kpTiC = 0.2 exp(-61,800/RT) sq cm per sec for Tic and Kp HfC = 2.62 exp(-95,300/RT) sq cm per sec for HfC. The liquidus phase boundaries were determined from metal samples treated in graphite crucibles for different times ranging from 4 to 100 min at each of the temperatures indicated in Table 11. Metallographic examination revealed that the carbide precipitates were distributed uniformly throughout the frozen metal matrices. This is attributed to the rapid cooling rates (800°C per min) and the small difference in density between the precipitated carbide and the liquid metal.

Jan 1, 1968

By B. S. Butler

STUDY of the ore deposits of Colorado has disclosed, in numerous places, sharp changes in both mineralogy and metal content of the primary or hypogene deposits with change in depth. A clear understanding of the meaning of these changes is requisite to form intelligent conclusions that can be applied in the exploration of such ore deposits. This paper is an attempt to set forth some of the geologic and chemical relations of minerals that bear on this problem. The effect of the differing electrode potentials of elements on the order of oxidation and on the order of displacement of one metal by another metal in supergene sulfide deposits has been studied for many years by several investigators. The results all agree rather closely with the original Schürmann series of replacability of metal sulfides, as Wells has shown.1 So far as the writers are aware there has been little attempt from the geologist's viewpoint to correlate the electrode potentials of the elements, other than those of the common metals, with the positions and mode of combination of the elements as found in ore deposits, and in particular in hypogene deposits. Wells' discusses electrochemical activity between solutions and certain ore minerals and mentions the possibility of its effect in precipitation reactions. The senior writer for a number of years has emphasized the importance of oxidation-reduction reactions as a factor in the formation of certain hypogene ore minerals, and as the electrode potentials are a measure of the relative oxidizing and reducing power of the elements and their ions, it seems possible that a study of them may offer some suggestions on certain problems. The data at present available for such a line of attack on oxidation-reduction reactions are too far from complete to offer much help, nevertheless the table of standard electrode potentials

Jan 1, 1929

THE Johnson award for 1926 was given to T. L. Joseph for his experimental work on blast-furnace operation. When the Bureau of Mines undertook its experimental blast-furnace investigation in 1919, a number of operators and metallurgists were doubtful as to the practicability of small-scale tests. Several pre-vious attempts, outside the Bureau, to operate small furnaces had been unsuccessful. However, pig iron was produced in three and four-ton furnaces during the first half of the nineteenth century. The operation of a small furnace did not therefore seem an impossible task. This point of view, together with a realization of the importance of problems connected with the pro-duction of pig iron, prompted the Bureau to undertake this work. Such problems as the feasibility of using charcoal briquets as a fuel, the application of oxygen enriched blast, and the use of new ores and raw ma-terials, in general, can be investigated only at consider-able cost on full sized furnaces, while with an experimental furnace they can be conducted at a com-paratively ;small, cost. The results of small-scale tests are sufficient to determine whether the problem. War-rants the expenditure required for a trial on a com-mercial scale. The accompanying photographs and chart show the various stages of the experimental furnace development. Some idea of the size and shape of furnaces which were tested can be had from the development chart. In oper-ating furnaces A to F, a series of changes were made to increase hearth temperature. Perhaps the most im-portant change was the position of the tuyeres with respect to the bottom of the hearth. The height of the tuyeres above the hearth was gradually increased and the hearth diameter decreased. It was shown by this series of furnaces that metal and slag are the chief source of heat supply to the crucible. For this reason there is a minimum rate at which these materials can be brought into the hearth of a small furnace if it is to function properly. The rate of slag "and metal fall are determined by the burden on the furnace and the rate of blowing. Due to lack of funds necessary to provide ample blowing equipment, hot blast stoves, essential mechani-cal features, and to meet operating expenses, it. was necessary to work with much smaller furnaces, such as G to K shown in the chart. The particular object of these tests was to study the extent to which reactions could be speeded up by decreasing the size of the stock. One decided change, noticed at the beginning of this series of tests, was the effect which coke size had on the production of a strongly reducing gas. Furnace G, 22 in. high, operating on coke crushed to pass 10 mesh, made a gas richer in carbon monoxide than did fur-naces A to F, operating on run-of-the-oven coke.

Jan 3, 1927

Solution mining got back in the news recently when Kalium Chemicals, Ltd., a joint subsidiary of Pittsburgh Plate Glass and Armour & Co. announced its plans to go full speed ahead in mining potash by the solution method in its vast holdings 30 miles west of Regina, Saskatchewan. The company is keeping the technical details of this mining technique under wraps for competitive reasons, but company officials insist that the major difficulties in solution mining of potash have been overcome and that the final product will have definite competitive advantages on the open market. Kalium's holdings in the Regina area total about 500 sq mi. The ore-primarily sylvite mixed with appreciable quantities of halite-occurs in the Prairie Evaporite formation at a depth of 5300 ft. The ore zone averages about 100 ft in thickness. Too deep to be economically mined by conventional underground methods, such as is being done at International Minerals & Chemical Corp.'s Esterhazy mine (depth about 3100 ft), Kalium gambled that it could develop a successful method of solution mining even though earlier attempts in Germany, the U.S., and Canada had failed.

Jan 6, 1964