Search Documents

By AIME AIME

IN A STATEMENT summarizing general conditions in the Federated American Engineering Societies, the executive secretary, L. W. Wallace, expresses the belief that the Federation has made substantial progress. At the annual meeting of the American Engineering Council, to be held in Washington Jan. 5 and 6, this progress will be shown by reports covering activities in many fields. "Unquestionably," says Mr. Wallace, "the Federa¬tion has made favorable and permanent contacts in Washington. Through the, activities of Congress and of the new Federal administration. we have had the opportunity to render some really constructive service. We feel, however, that the great body of engineers are not adequately informed of the organization of the Federation, of its aims and purposes and of its activities.

Jan 1, 1921

By Charles Albert Ashburner

The coal-fields of the United States have been variously classified as to their geographical positions. In 1887 I proposed slight changes to the classification generally used, for more convenient description of our coal-fields in my report on the statistical history of coal in the States during 1886 for the United States Geological Survey. This new classification seems to meet all practical requirements and has been generally adopted. The coal-areas are grouped in two divisions—the anthracite division and the bituminous division. The anthracite division, in a commercial sense, may be said to include the anthracite districts of Pennsylvania alone, although small amounts of anthracite are mined in Colorado and have been

Jan 1, 1890

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, all of the following rock types occur; oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently, overblasting wasted drilling time, and explosives caused excessive throw.

Jan 4, 1974

By H. E. McKinstry

LIKE nearly everything else, mining geology has been reconverting. Many geologists had been in military and other government service. Many more, with mining companies, had been working primarily toward increasing production from known reserves. All of these are turning now toward their normal peacetime endeavor-the search for new ore; for most mining companies, finding themselves with accumulated deficits in development work, are more than ready to go ahead with their postwar plans made a year or more ago but still stalled at the close of 1945 for lack of man power. These plans include not merely development in the old home camp but also wide exploration for new prospects both domestic and foreign. Most of the large concerns have geologists and engineers in the field in the United States, despite the outlook for higher mining costs here, and at least half a dozen strong American companies are already investigating opportunities abroad, notwithstanding past unhappy experiences in certain Latin-American nations which have welcomed capital but later found means of preventing investors from reaping the reward of their enterprise. A few of these new foreign expeditions are following well-planned programs, but too many, in their haste to get any sort of footing, are proceeding without well-considered policy. with the result that their geologists can do little more than desultory scouting.

Jan 1, 1946

Tars Committee is the result of a desire of the authorities in charge of the publications of the four national engineering societies to co-operate in this matter. The members of the Committee are the following: Charles WarreN Hunt, Secretary of the American Society of Civil Engineers. D. S. Jacobus, Vice-President of the American Society of Mechanical Engineers. Joseph Struthers, Assistant Editor of the American Institute of Mining Engineers. CaRy T. Hutchinson, Chairman of The Editing Committee of the American Institute of Electrical Engineers. This Committee has held several meetings; it seemed advisable, at the outset, to limit its discussions closely to the general subject of abbreviations. Further, it seemed best to formulate a few general rules to be followed in making abbreviations, rather than to compile a list of forms to be recommended. The Committee decided to limit the subject more narrowly by considering only abbreviations to be used in the text, or general reading-matter, arid not those to be used in special matter,

Jan 1, 1905

By Clyde E. Williams

THIS review of the progress made in iron and steel metallurgy during the past year is confined to developments in this country. It attempts to give examples to illustrate progress made rather than to appraise results. As a result of the gradually diminishing supply of rich iron ores and of predictions made as to the probable life of the iron-ore reserves of the Lake Superior District, attention of iron and steel executives was directed to the question of beneficiation of iron ores. Laboratory and plant-scale experimental work was conducted on the wash ores .of Minnesota and an investigation, was, begun on the Old Range low-grade ores.

Jan 1, 1931

By A. L. Slaughter

The Homestake mine, located in western South Dakota, was discovered in 1876. The first reported production was in I 878. Total production through 1965 is 6,554,249 troy ounces of silver and 27,961,276 troy ounces of gold, worth $987,000,000 at present prices. Precambrian sedimentary formations at Lead total 20,000 feet. The Poorman Formation, the oldest, is chiefly ankerite carbonate. The Homestake Formation is iron-magnesium carbonate. The younger formations are argillaceous with some quartzites. The Cambrian Deadwood Formation unconformably overlies the Precambrian. All are cut by Tertiary intrusives. Sideroplesite schist of the Homestake Formation was converted to cummingtonite schist in the zones of higher-grade metamorphism. The Precambrian rocks show the effects of extreme isoclinal folding. A second stage of folding ( cross folds) may have been caused by the Tertiary intrusives. All folds plunge to the southeast. The Homestake ore bodies are pipe-like replacements of the Homestake Formation in zones of cross folding. It is believed that dilatation of the schists has increased permeability in these zones. Chloritization of the schists is the most widespread effect of the mineralization which is divided into four stages. Principal minerals of the first stage are quartz, chlorite, and arsenopyrite; in the second stage, quartz, ankerite, and pyrrhotite. In the third stage only pyrrhotite was deposited. The fourth stage followed the intrusions of Tertiary dikes and deposited mostly pyrite and calcite. Gold accompanies all stages and is always the last mineral to be deposited. It is most closely associated with arsenopyrite of the first stage but can be interpreted as having been deposited during the fourth stage and superimposed on the products of the earlier stages.

Jan 1, 1968

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

By William L. Batt

FROM the time the Japs overran the Far East, the United Nations faced a serious military problem in the critical shortage of many raw materials desperately needed to prose¬cute the war on two fronts. For many months this critical shortage threatened substantially to limit the gigantic effort to get shooting equipment into the hands of the fighting men on the far-flung battle lines. Now this crisis has been met. Solvency in raw materials has been achieved. Simply stated, this job of producing solvency has been done by "cutting cloth to fit the garment." This does not mean that we have all the raw materials we need. Unfortunately, a few raw materials are still short, thereby limiting the total production of certain war goods, or making these goods less effective. Where the supply of raw materials is known to be limited, however, substitutions have been made or production schedules have been geared to the amounts available, and an over-all balance has been achieved between various parts of the war-production program.

Jan 1, 1943

By F. B. Sherman, Keros Cartwright

Sanitary land filling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Knowledge of ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for natural limitations at a particular site. Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites; (2) site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources; (3) research on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills; and (4) formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers. Throughout history, man has disposed of unwanted materials by dumping. As urbanization has increased, haphazard dumping practices have given way to disposal under more controlled conditions because of increasing congestion of population and production of waste and greater concern for public health and environmental amenities. Many states and communities have already outlawed open dumping and open burning of refuse. The only practical methods of disposal of large volumes of refuse, therefore, are contained, high-temperature incineration, or burial in a sanitary landfill. In Illinois, regulation of solid waste disposal has been delegated to the Environmental Protection Agency. Each session of the legislature since 1965 has passed increasingly strict laws regulating waste diposal. As a result, the work of evaluating sanitary landfill sites has increased significantly for both the Department of Public Health, now the Environmental Protection Agency, and the Illinois State Geological Survey, which advises the Agency on matters of ground-water geology and pollution. In fact, our ground-water staff spends as much time on studies relating to waste disposal, primarily sanitary landfills, as on ground-water resource studies. Many other geological agencies are experiencing similar demands for increased assistance in solving waste-disposal problems. This paper summarizes some of the salient features of the sanitary landfill concept, describes activities of the Illinois Geological Survey in ground-water and engineering geology relating to landfills, and suggests policies that need consideration. A sanitary landfill is located and operated in such a way that vermin and pests, nuisances, and degradation of air and water are kept at acceptable levels. Some of the physical requirements of a sanitary landfill are all-weather roads for year-round access, fences to retain blowing paper, a daily cover of at least six inches of suitable earth material, and a final cover of at least 2 ft of earth material. Dumping into or adjacent to standing water generally is not allowed. Two common operating techniques are used. In the first, trenches are dug, the refuse is placed in them, and the earth removed from the trenches is used to cover the waste. In the second method, area fill, refuse is placed in low ground and covered with earth from adjacent high areas. The hydrology of the site is a prime consideration in locating sanitary landfills. Putrescible refuse, if saturated above field capacity, produces a leachate that usually has a high concentration of dissolved solids.2 As the leachate also acts as an agent for transporting bacterial pollutants, it constitutes a potential pollution hazard. To reduce the production of leachates, the topography of the landfill area should be such that surface water will not flow into or through the fill. Operations that will result in refuse disposal below or near the highest known water-table elevation may be required to take corrective or preventive measures to protect the ground water. In practice, under humid conditions such as prevail in Illinois, locations where disposal can take place above the water table are relatively few because surficial materials are commonly fine-grained, which permits slow gravity drainage and results in high degrees of saturation (100% moisture content) near the surface. At some sites, although disposal has taken place above the water table, ground-water mounds have developed, resulting in permanent saturation of the refuse. Permeability barriers usually are required to protect the ground-water reservoir from degradation by leachates. The convention in Illinois is to have a minimum of

Jan 1, 1972

By J. J. Rutledge

I. DESCRIPTION OF THE CLINTON ORES AND ASSOCIATED POCKS. THE Clinton rocks in Stone Valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.1 A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the tipper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, Composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Nov 1, 1908

By G. H. BUCHANAN

ALTHOUGH the nomenclature of the chemical tools of flotation is probably familiar to you, it will do no harm to review it; . In order to make the terms more real I have employed an illustration which likens flotation to an old-fashioned balloon ascension, such as we witnessed in boyhood at the county fair. The mineral to be floated is the aeronaut, conspicuous in his gilt-spangled tights, who is to be separated from you and me and the other small boys who are standing about, said boys being the g-a-n-g-u-e, or g-a-n-g, as we would have spelled it. The oil film surrounding the bubble is the counterpart of the silken fabric of the balloon, and bubble and balloon will rise for. the same reason, namely. that the fluid outside it is heavier than the fluid within. In flotation reagent nomenclature the material of which the bubble is made is called the "frother.",

Jan 1, 1930

By Allen Rogers

IT has always seemed to me that there is a certain similarity between the work of the mining engineer and that of the doctor of medicine-each has very often to be governed in his actions by conditions which he cannot. see. It is not necessary to detail the unseen conditions with which the mining engineer or geologist has to deal-the further extension of orebodies; the existence of new ones, the throw of a fault, the probable change in grade or character of the ore with advance of the workings, are a few of the conditions which the mining engineer has to determine as well as he can from the deductions he is able to make from what he can observe. Just so the physician is often confronted with conditions that he can not observe. Probably less than half of human ills make a manifestation at the surface of the body from which definite and certain conclusions can be drawn. The diagnostician must observe various things and, from these observations in combination, conclude what 'his course should be to bring about the cure of the trouble. Both professions would be assisted immensely by any agency that would permit them to look below the surface, something that would make more certain the diagnosis which each is called upon to make. The physician has had such an agency since 1895, when Röntgen discovered the X-ray; which, by making possible shadowgraphs of the osseous portion of the human body, advanced immensely the diagnosis of bone lesions. Later, with improvement in the technique and more understanding in the interpretation of what the photographic plate shows, other portions of the human anatomy could be examined and at the present time there is hardly an instance of internal disorder to which the aid of the X-ray is not called. Some organs are made opaque by administering mineral substances; in, other cases, conclusions are drawn from barely perceptible shadows on the photographic plate. Generally the surgeon's knife is directed with exactitude to the seat of the trouble and so not only is the difficulty revealed but the necessity for an exploratory' operation is averted.

Jan 1, 1928

By Allen H. Rogers

It has always seemed to me that there is a certain similarity between the work of the mining engineer and that of the doctor of medicine — each has very often to be governed in his actions by conditions which he cannot see. It is not necessary to detail the unseen conditions with which the mining engineer or geologist has to deal—the further extension of ore-bodies, the existence of new ones, the throw of a fault, the probable change in grade' or character of the ore with advance of the workings, are a few of the conditions which the mining engineer has to determine as well as he can from the deductions he is able to make from what he can observe. Just so the physician is often confronted with conditions that he can not observe. Probably less than half of human ills make a manifestation at the surface of the body from which definite and certain conclusions can be drawn. The diagnostician must observe various things and, from these observations in combination, conclude what his course should he to bring about the cure of the trouble. Both professions would be assisted immensely by any agency that would permit them to look below the surface, something that would make more certain the diagnosis which each is called upon to make. The physician has had such an agency since 1895, when Röntgen discovered the X-ray; which, by making possible shadowgraphs of the osseous portion of the human body, advanced immensely the diagnosis of bone lesions Later, with improvement in the technique and more understanding in the interpretation of what the photographic plate shows, other portions of the human anatomy could be examined and at the present time there is hardly an instance of internal disorder to which the aid of the X-ray is not called. Some organs are made opaque by administering mineral substances; in other cases, conclusions are drawn from barely perceptible shadows on the photographic plate. Generally the surgeon's knife is directcd with exactitude to the seat of the trouble and so not only is the difficulty revealed but the necessity for an exploratory operation is averted. What the X-ray is to medicine and surgery, geophysical prospecting methods are to the mineral industry. They give the mining engineer and geologist information regarding subsurface conditions which otherwise

Jan 1, 1929

By J. F. Kemp

The use of nickel-steel has directed increasing interest of late towards the deposits of nickel, and at the same time the parallel advance in our knowledge of the basic igneous rocks has rendered these deposits a subject of important geological inquiry. Investigations have led to some views, more or less new, on the igneous origin of certain ores, which, though not universally accepted, have a growing number of adherents. In Europe, the mines in Norway have been especially suggestive subjects of study, and others somewhat less generally known have also added their testimony; while in this country the great economic importance and scientific interest of the developments in the Sudbury district of Canada, have furnished the principal texts for the discourses that have appeared among us. The purpose of the present paper is to set forth these views through the medium of one interesting ore-body, of which but little has been written ; and, by the description of another, to place in contrast two different geological associations in which nickeliferous pyrrhotite occurs, and to indicate a generalization, based upon these different geological characters, and justified by the experience so far gained. To Prof. J. H. L. Vogt, of Christiania, Norway, is due the chief credit for the revival of interest in the geology of nickel. His important contributions* of recent date have made generally available

Jan 1, 1895

By Albert F. J. Bordeaux

(Cleveland Meeting, October, 1912.) THE immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia, would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development, of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or ire even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a snap of Eastern Siberia, showing the mineral deposits.

Oct 1, 1912

By Lawrence K. Nordell

This paper reviews practices used In the selection and sizing of belt conveyors and stacker systems commonly used in crushing and grinding plant facilities. Historical and modern methods of sizing this equipment are presented. The new methods Include: 1) probability theory applications for establishing component reliability, 2) "Monte Carlo" simulation techniques used in evaluating alternative system designs and in establishing service factors and corresponding availability Indices of each system, 3) quantifying the system and component operating characteristics using computer assisted modeling tools simulating rigid body and elasto-mechanic behavior for starting and stopping large and/or complex belt conveyors.

Jan 1, 1982

By George C. Heikes

ALTHOUGH the application of light metals in war materiel increased during the year, based on the number of uses, the trend in aluminum and magnesium production in 1944 was characterized by a sharp decline in the production of both metals accompanied by a further accumulation of large Government reserve stocks. Several primary reduction plants were curtailed to prevent building excessive inventories. By the end of the year, however, a lively revival of war production took place when resistance stiffened on the western front in Europe. Production of primary aluminum ingot was reduced from over 90,000 tons per month at the start of the year to 45.000 tons per month by the end of the year.

Jan 1, 1945

By Open-Hearth Steel

I received a telegram yesterday from Mr. J. H. Nead saying that he regretted circumstances had come up which prevent his attending the meeting, but that arrangements have been made and Mr. T. S. Washburn, of Inland Steel, will act as the Co-Chairman in his stead. We are sorry, of course, that he cannot be here at this conference. We have, therefore, asked Mr. James J. Bowden, chief metallurgist of Republic Steel Corporation, Cleveland, to act as Chairman and Mr. Tom Washburn to act as Co-Chairman. I will turn the meeting over to these gentlemen at this time.

Jan 1, 1940

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968