Search Documents

By A. L. Benham, W. E. Dowden, W. J. Kunzman

The mechanism involved in creating a miscible fluid displacement of typical reservoir fluids through porous media by light hydrocarbon mixtures usually involves a number of mixing and separation stages in the contact area. This mechanism has been illustrated on ternary diagrams for miscible displacement of reservoir fluid by rich hydrocarbon gases. A relatively simple method has been devised for calculating the approximate conditions for a miscible displacement of reservoir fluid by rich, light hydrocarbon gases or by LPG mixtures. Miscibility is favored by increased pressures, decreased temperatures, light reservoir fluids and light hydrocarbon-displacing fluids rich in the heavier components. The conditions for miscible displacements of five typical reservoir fluids by various light hydrocarbon mixtures were determined for a range of temperatures from 70" to 260°F and pressures from 1,000 to 3,000 psia. A correlation of these conditions was obtained using the variables of temperature, pressure, C,+ molecular weight of the reservoir fluid, C,+ molecular weight of the displacing fluid, and mol per cent methane in the displacing fluid. This correlation has been applied to data appearing in the literature with very good success. A partial check of the correlation has been made using a step-wise procedure with a windowed PVT cell. INTRODUCTION The term, "miscible fluid displacement", may be defined as any oil-recovery displacement process where there is an absence of a phase boundary or interface between the displaced and displacing fluids. A water flood would not be a miscible fluid displacement, although cycling in a condensate reservoir would be. Another example is displacement of oil by gasoline. Not so obvious, however, are the conditions under which fluids (such as propane, mixtures of propane and methane, or other similar systems) will give a miscible fluid displacement of oil. There are four standard miscible-fluid-displacement processes being used for the recovery of oil from an "nderground reservoir—(1) high-pressure dry-gas miscible displacement, (2) rich-gas miscible displacement, (3) miscible slug using a slug of LPG followed by a lean dry gas under miscible conditions, and (4) gas driven-slug process using a slug of LPG followed by a lean dry gas under immiscible conditions. The first problem faced by the engineer designing a miscible displacement process is to determine the conditions for miscibility. A number of papers have included discussions of the process of obtaining miscibility in these processes.1-8 However, methods for calculating the conditions for miscibility have not been published. This paper includes a method for calculating the conditions for a miscible displacement of reservoir fluid by a rich gas (LPG diluted with methane or natural gas). In this paper, a rich-gas miscible displacement process is defined as an oil-recovery process in the reservoir. The cost of a rich-gas miscible displacement will be decreased by diluting the LPG with methane or natural gas as much as possible. Therefore, it is important to be able to predict the maximum dilution for miscibility. MECHANISMS The mechanisms for obtaining miscibility between a displacing mixture of light hydrocarbons and displaced reservoir fluid often involve a number of displacing and mixing stages. As stated previously, the cost of a rich-gas miscible displacement is decreased by diluting available LPG with natural gas. The problem is to predict the maximum dilution allowed while maintaining miscibility. To get a picture of the displacing and mixing stages, it is helpful to consider these complex hydrocarbon mixtures as pseu do-ternary systems. Graphical representation of a complex system as a pseu do-ternary system can be thermodynamically rigorous if enough variables are used to describe the character of each pseudo-component in one of the phases. However, even if the characterization of each pseudo-component is not complete, pseudo-ternary representation does serve to illustrate the mechanism for obtaining miscibility and can be used to make some general conclusions concerning the conditions for obtaining miscibility. A phase diagram for the ternary system, methane-

By Harold A. Krueger

FACILITIES and mining operations of the National Lead Co., St. Louis Smelting and Refining Division, near Fredericktown, Mo., are situated in a famous mining area. Copper, lead, nickel, and cobalt have been mined here for more than 100 years, work having been started on a high sulphide copper outcrop in 1847. Lamotte sandstone is characterized by differential compaction on a rigorously eroded pre-Cambrian surface. The Bonneterre formation was therefore a good host for minerals not generally found in mineable quantities in these midwestern areas. Unusually complex minerals, however, make beneficiation difficult, and because of irregular ore thicknesses and elevations many engineers and operators have not attempted to mine the property. Others have tried who failed. This paper deals with economic, efficient, and competitive methods of mining these highly irregular orebodies, as compared to the open-stope, room-and-pillar methods normally used for horizontal-bedded lead deposits. For the purpose of this study it should be understood that the ore is found in two distinctly different types of occurrences, one to be designated as basin ore and the other as contact ore. Mining of basin ore is complicated by many faults, fractures, cross faults, and breaks. Contact ore is complex because it is found on flanks or slopes of pre-Cambrian knobs or highs. The dip of the mining floor for the latter type varies between 18" and 45". Occurrences of both types of ore are complicated by water courses or solution channels which carry unconsolidated shale, lime, sand, and dolomite. This material is also found between the bedding planes of the members of the Bonneterre formation. The water found where there are fractures, faults, and channels makes it very fluid and tacky, see Fig. 1, particularly after it has been blasted and handled by loading and hauling machines. Much of the ore can be wadded and thrown without dispersing. During early operations by the Buckeye Copper Co. in 1861 and the North American Lead Co. from 1900 to 1910, conventional narrow-gage railroad and side dump mine cars were used with hand shoveling. The complications of mining the contact ore, the only type attempted at this time, can be appreciated when it is realized that operators were obliged to use mules for haulage. Haulageways constructed on these slopes were of necessity similar to wagon trails or goat trails up the side of a mountain. In other words, it was merely a matter of going from side to side of the strike length of the slope, gaining a little in elevation on each shuttle trip. Production totaled only one to two tons per manshift. A few years later, about 1913, the property was purchased by combined Canadian interests known as the Missouri Cobalt Co., and the use of trolley locomotives was initiated. Between 1900 and 1928 a land agent using churn and diamond drilling methods prospected scattered sections of the area. In 1928 the first property was purchased by the present company, then operating as the St. Louis Smelting and Refining Co. Check drilling and prospecting was carried out by the company at various times between 1928 and 1939 to correlate the erratic mineralization. Much information about both types of orebodies was accumulated, but it was still questionable as to whether money should be invested to work these occurrences. In anticipation of high lead and copper prices, about the time World War II started, it was decided to develop and bring into production some of this ore. In 1942 No. 1 shaft was put down on the largest basin-type orebody and in 1943 No. 2 shaft was put down on contact-type ore. Operations were expanded when No. 3 shaft was completed in 1943, and progressed further in 1948, when National Lead Co. dewatered and opened No. 5 and 6 mines, old workings of the North American Lead Co. and the Missouri Cobalt Co. Because of the differential compaction of Lamotte sandstone over the pre-Cambrian porphyry, in some instances mineable thicknesses of basin-type ore occurred 20 to 30 ft above the sand. This is the exception rather than the rule, since most of the mineralization starts at the sand and is variable in thickness. The ore was attacked, therefore, by development drifts and crosscuts at the lowest possible elevation, where the ore immediately overlying the Lamotte sandstone could be drained and made accessible for mining. It was planned to connect to the drifts and crosscuts with raises to mine ore deposited 20 to 30 ft higher. The higher orebodies were thus mined as slusher levels. Slusher hoists were used to drag the ore into the raises, which were made into hoppers. The ore was then loaded into 32x32-in. ore cans, hauled to the shaft by battery locomotives, and hoisted by the conventional Tri-State method. The rate of efficiency was 5 to 6 tons per manshift underground. The contact-type ore was attacked in a similar way, except that the orebodies were not nearly so wide, so that they were more flexible for slusher loading into cans. This advantage was offset, however, by haulage complexities, since the railroad was constructed on steep slopes. Through experience and ingenuity, many improvements were made in mining both types of ores. The two levels, so-called, in the basin-type ore-bodies were connected as previously planned, more efficient locomotives replaced the older ones, and a

Jan 1, 1954

By Oliver Bowles

WHILE vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate dis¬cussion of metallurgical limestone problems.

Jan 1, 1928

By Earl C. Henry

Magnetic iron ore was mined in Essex County, N. Y., during the American Revolution; Benedict Arnold is said to have mined ore near Port Henry to secure iron for chains and spikes for the Lake Champlain fleet. Details regarding the operations prior to 1804 are not easily obtained but work on a commercial scale appears to have been started about 1838. The Witherbee, Sherman & Co. was established in 1849. The property of the district is held in fee almost entirely by the mining companies. The Mineville iron-ore district, as well as the entire Adirondack region, belongs to the pre-Cambrian complex. The readily identified rocks consist of gabbro, anorthosite, syenite, and granite, and are classed as igneous, eruptive, and intrusive. In addition, there is a great variety of gneisses, rocks with a variable mineral composition but all more or less distinctly foliated. The Grenville series are the oldest rocks in the district; this series consists of graphitic white limestones, graphitic sandstones, and quartzites and gneisses with or without graphite. The orebodies occur in the gneissic rocks and are comformable to the structure of the rocks. The typical occurrence of the ore in this district is in lenticular bodies with a parallel pitch to the southwest; this structure is best exemplified in the New Bed mine. The Harmony and Old Bed orebodies are faulted by two sets of diabase dikes, one set having a southwest strike and the other set an east-west strike. The ores occurring in the acid gneissic rocks are non-titaniferous. The ores occurring in the gabbros and anorthosites are high in titanium; these deposits are irregular, have no structural relation with one another, and are unquestionably of igneous origin. The origin of the gneissic rocks and the ores therein contained is not settled; both the sedimentary theory of ore concentration and the igneous theory of magmatic segregation have been advanced. The iron mineral in all the orebodies is crystalline magnetite; some very perfect and large specimens have been obtained. The gangue is

Jan 1, 1925

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By Oliver Bowles

While vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little atten. tion compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux " that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

By John. C. Reed

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62° W. The average dip is about 67° SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30° W. and average dips about 75° SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30° for the south-west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62º W. The average dip is about 67º SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30ºW. and average dips about 75º SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30º for the south- west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By G. E. Archie

The usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy. Introduction The electrical log has been used extensively in a qualitative way to correlate formations penetrated by the drill in the exploitation of oil and gas reservoirs and to provide some indication of reservoir content. However, its use in a quantitative way has been limited because of various factors that tend to obscure the significance of the electrical readings obtained. Some of these factors are the borehole size, . the resistivity of the mud in the borehole, the effect of invasion of the mud filtrate into the formation, the relation of the recorded thickness of beds to electrode spacing, the heterogeneity of geologic formations, the salinity or conductivity of connate water, and, perhaps of greatest importance, the lack of data indicating the relationship of the resistivity of a formation in situ to its character and fluid content. On the Gulf Coast it is found that the effects of the size of the borehole and the mud resistivity are generally of little importance, except when dealing with high formational resistivities or extremely low mud resistivities. Fortunately, little practical significance need be attached to the exact values of the higher resistivities recorded. Low mud resistivities are not common, but when this condition is encountered it may be corrected by replacing the mud column. With the present advanced knowledge of mud control, invasion of mud filtrate into sands can be minimized, thereby increasing the dependability of the electrical log. The effect of electrode spacing on the recorded thickness of a bed is often subject to compensation or can be sufficiently accounted for to provide an acceptable approximation of the true resistivity of the formation. As development of a field or area progressively enhances the knowledge of the lithologic section, the resistivity values of the electrical log take on greater significance, ultimately affording acceptable interpretations. The salinity, and

Jan 1, 1942

By G. E. Archie

The usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy. Introduction The electrical log has been used extensively in a qualitative way to correlate formations penetrated by the drill in the exploitation of oil and gas reservoirs and to provide some indication of reservoir content. However, its use in a quantitative way has been limited because of various factors that tend to obscure the significance of the electrical readings obtained. Some of these factors are the borehole size, . the resistivity of the mud in the borehole, the effect of invasion of the mud filtrate into the formation, the relation of the recorded thickness of beds to electrode spacing, the heterogeneity of geologic formations, the salinity or conductivity of connate water, and, perhaps of greatest importance, the lack of data indicating the relationship of the resistivity of a formation in situ to its character and fluid content. On the Gulf Coast it is found that the effects of the size of the borehole and the mud resistivity are generally of little importance, except when dealing with high formational resistivities or extremely low mud resistivities. Fortunately, little practical significance need be attached to the exact values of the higher resistivities recorded. Low mud resistivities are not common, but when this condition is encountered it may be corrected by replacing the mud column. With the present advanced knowledge of mud control, invasion of mud filtrate into sands can be minimized, thereby increasing the dependability of the electrical log. The effect of electrode spacing on the recorded thickness of a bed is often subject to compensation or can be sufficiently accounted for to provide an acceptable approximation of the true resistivity of the formation. As development of a field or area progressively enhances the knowledge of the lithologic section, the resistivity values of the electrical log take on greater significance, ultimately affording acceptable interpretations. The salinity, and

Jan 1, 1942

By W. J. West, T. D. Mueller, J. E. Warren

Two methods are used to obtain the relatiorlship between ratio of gas to oil permeability and gas saturation. One method is to calculate a curve from field measurements of reservoir behavior: the other is to measure the relationship on a core .sample in the laboratory. The curves resulting from these TWO methods arc often comparer1 and seldom found to agree. The most important reason for the nonagreement is often overlooked. This reason is that the performance k9/k0 curve is calculated with the assumption of uniform pressure and saturution throughout the reservoir. To show the differerence between performance type kg/k0 curves and laboratory type kg/k0 curves. two performance type kg/k0 curves for two different production rates were calculaled from the production perforrnance of a hypothetical reservoir for which a laboratory type curve was assumed. Production performance of the hypothetical reservoir bras calcu- lated by use of international Business Machine's 701 Computer. The perfortnance type kg/k0 curves differed from the laboratory curve for the hypothetical reservoir. The performance type crrrve for the lowest production rate most nearly coincided with the laboratory curve. INTRODUCTION Predictions of oil reservoir performance are often made with the aid of complex numerical calculations. An important quantity required in these calculations is the ratio of gas permeability to oil permeability (kg/k0 )at a particular gas saturation. Two methods arc used to obtain a relationship between this ratio and gas saturation. The curves resulting from these two methods are called performance kg/k0 curves and laboratory kg/k0 curves. The performance curve is obtained from field measurements of reservoir behavior. Particular kg/k0 values are calculated from the producing gas-oil ratio, the cumulative reservoir withdrawals, the original oil in place, the average reservoir pressure, and the PVT properties of the reservoir fluids. The particular kg/k0 values are then plotted against the average rcservoir gas saturations for the entire history period. In order to use this derived kg/k0 relationship for performance predictions, a curve through these points is extrapolated to higher gas saturations. The laboratory kg/k0 curve is obtained from measurements made on core samples. Saturation is maintained uniform throughout the core during these measurements. The kg/k0 curves obtained with these two independent methods are often compared and seldom are found to be the same. Various reasons have been offered for the lack of correlation. One is that insufficient core? were obtained to derive a curve representative of the reservoir rock. Another is that laboratory methods have failed to reproduce reservoir conditions. The most important reason for the noncorrelation has been often overlooked because of the difficulty in evaluating its effect. This reason is that the performance or field kg/k0 curve is calculated with the assumption of uniform pressure and saturation throughout the reservoir. In any

Jan 1, 1956

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By C. B. Manula, R. Venkataramani

Application of computers to present-day open-pit mining with bucket wheel excavators (BWE) is discussed. The development of the wheel excavators and their use in mining are discussed along with the necessity for building a computer model of the bucket wheel and the mathematical formulation of the problem. The simulation procedure, testing the model, and test results are summarized. Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the 20th century. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management, and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mold of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. Constant efforts are needed to improve upon productivity if the ore is to be economically mined. The development of vast low-grade deposits and thick overburden deposits calls for better tools to handle the enormous amount of materials. A natural solution to this problem is the use of bucket wheel excavators (BWE), which employ a continuous cutting head to feed the materials handling system. High productivity, versatility, economy of operation, and adaptability to most types of haulage systems combine to make BWE's attractive for large earth-moving operations. "Operating costs are being pushed down by the impact of giant haulage units, by high-speed conveyors, and computerized railroads. Matching all these with the continuous output of BWEs, one can visualize increased production at much lower costs." Historical Background The wheel excavator, which was patented in Germany in 1913, made its first appearance in an open-pit lignite mine in 1920. From this early beginning, however, BWEs were slow coming into practice. Initial developments were dampened by many design problems. From 1936 onward, major developments in design improved the wheel's ability, capacity, and versatility. A literature survey shows that wheel excavators are being used in Australia, Zambia, South Africa, the Congo, India, Indonesia, Czechoslovakia, Russia, Great Britain, Guyana, Yugoslavia, Morocco, Germany, Canada, and the U.S. for mining and loading chalk, lignite, clay, sandstone, phosphate, broken ore of iron, coal, shale, loose and semi-loose rock overburden.' A recent LMG* BWE at work in a German lignite mine weighs 6790 tons with an hourly capacity of 11,000 cu m. Although the BWE has wide applicability, its application to new mining areas poses a problem. Because of the large capital investment involved in BWE application and the narrow profit margins in mining low-grade ores or coal at depth, little margin of error can be tolerated in the selection, design, and operation of these machines. The questions that need to be answered prior to installation of a BWE for a mineable deposit are: 1.) What are the anticipated BWE performance characteristics? 2) Which method of BWE operation is most efficient? Attempts to answer these questions require a thorough knowledge of the mining system and the BWE operation. One approach is the building of a computer-ori-ented simulation model to determine how information and policy create the character of the BWE system under consideration. BWE Operation Modern BWEs generally excavate in blocks. Fig. la shows a BWE working in an established cut. The wheel is positioned to travel on the pit floor in line with the top edge of the old highwall. As it advances, a new highwall is exposed in the direction of excavation. Digging is done by rotating the wheel, swinging it from side to side in long parallel arcs, and "crowding" into the bank, by advancing the entire machine, or by the travel of the digging boom if an automatic crowd is available (Fig. lb). A second way by which the wheel can be advanced into the bank is by the falling cut method. A brief description of each of these methods follows. Cut with a Crowding Machine: At the end of every swing, the digging boom can be extended by the thickness of cut desired and the boom swung back in the reverse direction. Obviously, the thickness of bank excavated does not vary with the boom position; therefore, the slewing motion of the boom is fairly constant for uniform output. The thickness through which the digging boom can be advanced into the bank is theoretically calculated from the formula'

Jan 1, 1971

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941

By J. S. Ross

Although the opinion has prevailed for several years that bottoni-hole choking under certain flow conditions should effect an increase in flow efficiencies, the use of bottom-hole chokes until recently has been limited in application mainly because of mechanical difficulties encountered in their construction. Within the past year, however, bottom-hole choking, through the development of a removable type of choke, has been applied successfully under various conditions of flow in many Mid-Continent fields. The observation of these field tests indicates that bottom-hole choking, although not applicable to all flow conditions, has an important place in the operation of oil and gas wells. This paper gives briefly the conclusions drawn from the data obtained from the experiments with this bottom-hole choke under various flow conditions, and a description of the choke and its operation. Purpose of Bottom-hole Choking Since, in a normal well, the velocity with which the column of gas is moving generally has a direct bearing upon the quantity of oil it can lift, probably the main purpose of bottom-hole choking is to accomplish an increase in the velocity of this- rising column, particularly in the lower portion of the tubing string. This it does first, by expansion of the free gas accompanying the oil; next, by liberation and expansion of some of the occluded gas normally carried in the oil to the surface; and lastly, by atomization, which results in a more intimate and uniform mixture of the oil and gas. It is apparent, then, that if this velocity, particularly in the lower portion of the flow string, at a given rate of production, is inefficiently low, owing either to an insufficient supply of gas or to excessive surface choking, and slippage takes place, bottom-hole choking should bring about an increased velocity of the gas and hence an increased lifting capacity. But if the velocity of the column of gas at this same rate of production through a surface choke alone is at or above a velocity necessary to lift the oil efficiently, increasing the velocity by bottom-hole choking would probably serve no useful purpose, other than to steady the flow by the better mixture of oil and gas and to lower delivery pressures.

Jan 1, 1932

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941