Search Documents

By W. B. Lewis, M. E. True, M. C. Leverett

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By S. Vela, R. M. McKinley, L. A. Carlton

Johnson et al. have described a new well-testing technique that measures formation flow properties between wells.' The technique, called pulse-testing, requires a sequence of rate changes in the flow at one well and measzcrement of the re.rulting pressure changes at an adjacent well with a very sensitive differential pressure gauge. This paper describes an extensive application of the technique in a producing oil field. Pulse-tests on 28 of 45 possible well pairs in the field provided a picture of the areal distribution of reservoir hydraulic diffusivity, trans-missibility and storage. The primary objective in presenting these data is to demonstrate the potential of the methcid for reservoir description. A second objective is to show in three ways the qualitative and quantitative accuracy of reservoir parameters determined from pulse-tests: (I) pulse-test data show a nonuniformity in the field, closely correlating with the oil-water distribution as given by production data: (2) pulse-test values for permeability are comparable with core va1ue.s; and (3) perhaps most important, the field responds to a conventional interference test in the manner in which pulse-test data predict it should. The pulse-testing technique by Johnson et al.' is an ideal source of data for purposes of reservoir description, for it provides a measurement of formation storage S = +ch, hydraulic diffusivity 91 = k/+cp and transmissibility T — This paper describes an application of this method in a producing oil field. Results were analyzed to give numerical values for the parameters 7, T and S. These values were compared with oil-water production data (for the effect of fluid saturation), with core data and with data from an interference test. The reservoir in which the pulse-test survey was run is the result of a structural trap formed by a fault along the east side of a north-south trending anticline. A down-structure aquifer providcs a natural flank water drive for the pool. The producing formation is a dolomitic lime- stone having mainly vugular permeability; the formation oil has a gravity of 29" API with negligible dissolved gas. The field contains 19 wells, all on pump, arranged on 40-acre spacing along the top of the anticline. Fig. 1 shows the location of all these wells except two at the south end of the field. The dashed line on the right-hand side of the figure represents the approximate location of the fault with respect to well positions. Pulse-Test Survey and Analysis of Data A pulse-test requires a pulsing well and a responding well. In the field, changes were made in the rate of flow at the pulsing well by stopping and starting the pump periodically and measuring the corresponding pressure

Jan 1, 1969

By H. H. Rachford

Numerical solutions of immiscible flow problems in which dispersive effects of capillarity are dominated by convection require excessively fine grid spacing with attendant high computing costs. The use of coarser spacing reduces cost but often produces oscillation or undue dispersion associated with displacement fronts, A numerical formulation is proposed here which should be applicable to two-dimensional flow problems. it is in part analogous to an approach previously tested for miscible systems. The convective transport is approximated using a change of variables to yield a coordinate system moving approximately with the local characteristic velocity. The capillarity-induced dispersive terms in the differential system describing the process are approximated with respect to a fixed coordinate system by the usual implicit formulation. One-dimensional tests of the procedure yielded results in which the saturation profiles tended smoothly to the zero-capillary pressure solution as the ratio of viscous to capillary forces was successively increased in a sequence of calculations. This contrasted favorably with solutions by other numerical procedures which would require attendant grid refinements to approach the zero capillary pressure results. INTRODUCTION Numerical solution of displacement problems has until recently relied on applying methods developed primarily for transient heat-flow problems. Such problems are classified as parabolic in type, and where the heat transport is purely by diffusion their solutions are characterized by a high degree of smoothness. It is not surprising, therefore, that for approximating these solutions available finite difference methods are quite adequate. In flow problems the transport is partly by diffusion, partly by convection or flow. Although the problem remains of parabolic type because the dispersive effects of capillary forces or diffusion play some role in every displacement, at high flow rates the problem is dominated by convection, and solutions tend toward those of equations of the hyperbolic type. Solutions of hyperbolic problems are characterized by the translation of fronts, or discontinuities, that may progressively increase in sharpness. Numerical methods for treating parabolic problems become less and less satisfactory as displacement rates increase and the role of dispersion due to concentration or capillary pressure gradients becomes small relative to transport due to flow. In computation the difficulty manifests itself as an error associated with the grid size chosen. 1-6 In summary, if the heat-flow type approximations are to include the terms arising due to convection, one of several choices may be made: (1) an upstream (to the direction of flow) approximation for the convection terms may be used; (2) a centered-in-distance (CID) approximation may be used; or (3) a recently developed approximation based on the theory of oscillation matrices may be chosen.6 The last appears to have significant promise for one-dimensional flow problems; its extendibility to two or three dimensions is an open question. In either of the first two approaches, a suitably small ratio of v&/D must be maintained, where v is the velocity, & is the grid spacing and D the effective dispersivity in the direction of flow. In the first choice, the approximation of the convective part is only first-order correct and errors introduced appear as a numerically induced dispersivity of magnitude proportional to v?x. In the CID choice, the approximation can be second-order correct, but the difference formulation fails to satisfy the maximum principle unless a condition on v?x/D is met. Practically, this means that for high flow rates oscillatory solutions may result in the neighborhood of a front unless exceedingly small grid intervals are taken. While the procedure proposed by Stone and Brian4 permits a less severe limitation to be placed on this ratio, ultimately the flow rates increase relative to the dispersivity the oscillation obtains. Further, extensions of their approach to higher dimensional systems may be attended by considerable

Jan 1, 1967

By G. T. Davis, C. C. Mattax, M. O. Denekas

The effects of crude oil cornponents on the wellabil-ities of sandstone and limestone were investigated. Fractions containing cornponents differing in molecular weight and molecular structure were obtained from crude oils by distillation, extration and chromatography. Individual fractions were then tested for their effects on rock wettability. Tests indicate that sundstone wetta-bility may he changed by a complex variety of surfactants varying both in molecular structure and molecular weight. Limestone appears to be particularly sensitive to basic, nitrogenous surfactants. INTRODUCTION Investigations in recent years have shown that petroleum reservoir rock wettability can exert a significant influence on the efficiency with which oil can be produced by water flooding. While most reservoirs are presumably water-wet, they niay range in their degree of water-wettability from near-neutral to strongly water-wet.'" Reservoir wettabilities other than strongly water-wet are likely to be induced by adsorption of surface-active components froni the crude oil on the pore walls of reservoir rock.:' Little is known, however, about the nature of the surface-active materials which are likely to be adsorbed by the reservoir rock. Due to the complexity of crude oils. attempts made in the past90 isolate these surface-active components have met with only limited success. It is probable that many different types of surface-active materials arc indigenous to crude oils and that many of these may be adsorbed to varying degrees by reservoir rock. This was cxolored in the studies discussed in this paper. The over-all objective in these studies is to ascertain whether the wettability of a given reservoir can be determined by examining the surfactant content of the reservoir crude. To this end, crude oils were examined to determine the variability of indigeneous surfactants with regard to chemical type and molecular weight. Crude oils were separated by distillation into fractions differing principally in molecular weight, by chroma-tography into fractions containing compounds differing in polarity, and by solvent extraction into nitrogenous and non-nitrogenous fractions. Individual fractions were then tested for their effects on the wettabilities of sandstone or limestone rock samples. EXPERIMENTAL PROCEDURES Fractionation of the Crude Oils Samples of Miocene, Eocene and Jurassic crudes were distilled at temperatures not exceeding 200°C. The final stages of distillation were completed in a molecular still at pressures down to three microns of mercury. Fifteen to 30 fractions were obtained from each crude oil. These cuts were sufficiently broad that separation can be considered to have been effected principally on the basis of the molecular weights of the constituents of the crude oil. A considerable portion (20 to 40 per cent) of the crudes would not distill under these conditions. The residues were recovered and tested with the other fractions. Fractions differing in polarity were separated from a crude of Pennsylvanian age and an extracted sample of Miocene oil by chromatography, using a solid adsorbent. Since surfactants are, for the most part, polar compounds, chromatography should separate many of the surfactants from the crude oil. Such a separation should provide fractions containing compounds differing in molecular structure. Nitrogeneous compounds were extracted from Miocene crude oil with a solution of sulfuric acid in meth-anol. The residual oil was further processed by chonia-tography. Each of the fractions obtained by thesc procedures was dissolved in a non-polar solvent (xylene) and diluted to its original concentration in the crude oil. No attempt was made to maintain an anaerobic atmosphere above the samples while they were being dissolved. These solutions of the fractions were then tested for their effects on the wettability of sandstone and limcstone as discussed in the next section. Measurement of the Effects of Crude Oil Fractions on Rock Wettability No entirely satisfactory method for measuring rock wettability has yet been developed. All methods used are empirical. The imbibition test was used in these studies. This test is based on the tendency of a rock to imbibe the wetting phase spontaneously. For example, if a strongly water-wet rock is first saturated with oil and then placed in water, the water will quickly invade the rock by capillarity and much of the oil will be displaced. If the rock is slightly water-wet, water irnbibition will proceed more slowly and, in many instances, considerably less oil will be displaced. A water-saturated, oil-wet rock will imbibe oil. The initial rate with which water (or oil) imbibition takes place indicates, qualitatively, the degree of water (or oil) wettability of the rock.

By Joseph L. Jernegan

The Whale Lode occurs in the main range of the Rocky Mountains, Park County, Colorado Territory, at Hall Valley. It has been opened up and worked to some extent by the Whale Mine, situated some 11,300 feet above the level of the sea. The mine, with 700 feet of the lode on either side of the discovery shaft, is the property of the Hall Valley Silver-Lead Mining and Smelting Company. The adjacent country rock is a compact, fine-grained gneiss; its general strike is about north and south, dipping steeply to the west. In the immediate vicinity of the mine, the strata are very nearly vertical. The gneiss incloses numberless veins of a reddish granite, in which the feldspar largely predominates over the quartz and mica, the latter oftentimes being scarcely perceptible. As a general rule these granitic veins seem to more frequently follow the lines of stratification of the gneiss than otherwise. They are of varying width, some large, some small; the larger are from 5 to 6 feet wide. Gash veins of feldspar and quartz are also of very frequent occurrence. The general trend of the lode is about northeast. and southwest, intersecting the country rock at about an angle of 45 to its stratification. It dips to the northwest at an angle of 65. I am unable to state accurately how far this lode has been traced upon the surface, but it is at least well known to extend entirely through the mountain upon which the mine is situated, and is traceable over the ridge by a hollow extending for some distance along the surface, in which the lode crops out. This hollow in the surface rock has probably been formed through decomposition of the vein matter by atmospherical influences. The width of the crevice is variable, generally between 5 and 10 feet; the pay vein varies from an inch, or less, to 36 inches. The vein is generally accompanied both on foot and hanging walls by a whitish, semi-decomposed fock, composed of quartz and decomposed feldspar, and in some places—where the process of decomposition has not reached as advanced a stage—a lightgreenish or black mica. This rock, therefore, is in places composed of all the constituents of gneiss, and is undoubtedly nothing more or less than the same in a decomposed condition. It is often very strongly impregnated with iron pyrites, generally crystallized in minute cubes, and it is probably owing to the presence of this min-

By Joseph L. Jernegan

THE Whale Lode occurs in the main range of the Rocky Mountains, Park County, Colorado Territory, at Hall Valley. It has been opened up and worked to some extent by the Whale Mine, situated some 11,300 feet above the level of the sea. The mine, with 700 feet of the lode on either side of the discovery shaft, is the property of the Hall Valley Silver-Lead Mining and Smelting Company. The adjacent country rock is a compact, fine-grained gneiss ; its general strike is about north and south, dipping steeply to the west. In the immediate vicinity of the mine, the strata are very nearly vertical. The gneiss incloses numberless veins of a reddish granite, in which the feldspar largely predominates over the quartz and mica, the latter oftentimes being scarcely perceptible. As a general rule these granitic veins seem to more frequently follow the lines of stratification of the gneiss than otherwise. They are of varying width, some large, some small; the larger are from 5 to 6 feet wide. Gash veins of feldspar and quartz are also of very fre¬quent occurrence. The general trend of the lode is about northeast and southwest, intersecting the country rock at about an angle of 45° to its stratification. It dips to the northwest at an angle of 65°. I am unable to state accurately how far this lode has been traced upon the surface, but it is at least well known to extend entirely through the mountain upon which the mine is situated, and is traceable over the ridge by a hollow extending for some distance along the surface, in which the lode crops out. This hollow in the surface rock has probably been formed through decomposition of the vein matter by atmospherical influences. The width of the crevice is variable, generally between 5 and 10 feet; the pay vein varies from an inch, or less, to 36 inches. The vein is generally accompanied both on foot and hanging walls by a whitish, semi-decomposed rock, composed of quartz and decomposed feldspar, and in some places-where the process of decomposition has not reached as advanced a stage-a light-greenish or black mica. This rock, therefore, is in places composed of all the constituents of gneiss, and is undoubtedly nothing more or less than the same in a decomposed condition. It is often very strongly impregnated with iron pyrites, generally crystallized in minute cubes, and it is probably owing to the presence of this min-

Jan 1, 1875

By G. Thodos, E. M. Phillips

A reduced density correlation for the gaseous and liquid regions of ethane has been developed from all the experimental PVT data available in the literature for this substance. Saturated vapor and liquid densities reported for methane, propane and n-butane were utilized to establish the rectilinear-diameter line for ethane. This line was then used with the saturated-vapor data for ethane to produce the saturated envelope for this substance. Most of the saturated liquid data reported for ethane were found to be inconsistent with the saturated-liquid curve resulting from this study. The correlation covers the regions 0.65 < TR <6.0 and 0 < PR < 15. For regions for which no experimental data have been reported, the isobars of the correlation were extended by the use of the theorem of corresponding states. This correlation is presented both on rectilinear and log-log coordinates. INTRODUCTION At the present time, there is considerable interest in the exact PVT behavior of pure hydrocarbons. Matschke and Thodos12 recently have developed a comprehensive compilation of experimental vapor and liquid density data for methane. Similar studies have been conducted for other pure substances.4, 7 In the present study the density data available in the literature for gaseous and liquid ethane have been critically reviewed and utilized to develop a reduced density correlation for this substance. SATURATED LIQUID AND VAPOR DENSITIES The rectilinear-diameter rule proposed by Cailletet and Mathias5 states that the sum of the saturated liquid and vapor densities of a pure substance is a linear function of temperature which passes through the critical point. This law, although empirical, has been well established by continued verification since its conception in 1886. This rule has been applied to the saturated density data of methane,6 propane 17 and n-butane8 to produce the straight lines presented in Fig. 1 which pass through the critical point TR = 1.00, Pr = 2.00. The rectilinear-diameter relationship for ethane was established from the lines for the other substances in Fig. 1 by plotting the quantity p~, + PR against zc for different reduced temperatures. A critical analysis of the saturated vapor and liquid densities reported for ethane by Kuenen,10 Maass and McIntosh,11 and Sage, Webster and Lacey18 revealed that the values of PR1 + pr resulting from these studies were inconsistent with the rectilinear-diameter line obtained from the reliable density data of the other substances, as shown in Fig. 1. In the analysis of these data, reduced quantities were calculated using the critical con-

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well&apos;s drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well&apos;s limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well&apos;s cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well&apos;s drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR&apos;s are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR&apos;s in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.&apos;s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations&apos; and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.&apos; GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By Anthony Tuke

Members of the Society of Mining Engineers may well regard it as rather unusual that a paper on this subject is being presented by someone whose first taste of mining came at the age of 60 or so - someone who last heard of cathodes and anodes in 1938. On the other hand, the title does refer to the financing of a mine and at least I can claim to have spent all my business life since the war until 1981 in the world of banking, though this inevitably means that I have been used to looking at these and other problems through what you might regard as the wrong end of the telescope. The lending of money, and more particularly the provision of finance for commerce and industry, is the central job of a banker and I have been involved in this in various ways over many years, but regrettably only very marginally in the world of mining. As you will see from what follows, the rather specialised form of finance which RTZ required was, to my regret, not provided by the British banking community since the great majority of the finance came from American banks and, to a lesser extent, from German banks. I am most indebted to Mr. Roy Wright for a great deal of the nuts and bolts in this paper. He was one of the three central figures in the growth and expansion of RTZ during the 1950&apos;s and 1960&apos;s and was right at the centre of the negotiations with bankers, with governments and with many others. The going, as you will see, was far from easy. The essential basis for the financing of each of the RTZ group&apos;s mining projects was a firm long-term sales contract for sufficient of the output of the particular mine to produce the cash flow necessary to service the loans. Wherever possible, loans were raised in the same currency as the sales contracts were made. Each sales contract was designed to give the customer the product he wanted with a long-term assurance of supply and at the same time to give the bankers the protection they required. Thus the marketing concept and the financing concept for a particular mine formed one overall plan, and talks with the customers and the bankers were conducted in parallel until a satisfactory marketing/financial package was agreed in principle. Preliminary talks were begun soon after the discovery of a potentially viable orebody. As confidence about a discovery increased, customers were persuaded to enter into contingent sales contracts before the very detailed and costly business of the economic and technical feasibility study of the mine was launched; such a study might cost 10% or more of the estimated total capital cost. At the same time provisional understandings were reached with the bankers. The contingent sales contracts usually gave a period of grace of eighteen months to two years, during which time the decision whether or not to continue with the mine had to be made. This decision rested mainly on the result of the feasibility study and also on coming to a firm agreement with the bankers. If all went well and the mine went ahead, then the contingent sales contracts became firm, but they fell away if the decision was negative. The Company was fortunate that during the whole period when its major mines were being developed, world trade was increasing rapidly and Japan was becoming a dominant industrial power. The Japanese supported many of the mines, including Hamersley Iron Ore, Lornex Copper, Bougainville Copper to name a few, with the basic long-term sales contracts that enabled their development. The Germans supported Palabora and to a lesser extent Bougainville. The mines were financed as individual projects generally with a loan/equity ratio of about 65/35, without legal recourse to RTZ for the loans. RTZ was, however, responsible for providing any capital overruns required to bring the mines into commercial operations. Nevertheless, the RTZ management regarded itself as morally responsible to the lenders because, Palabora aside, the sales contracts had either a fixed selling price (like Hamersley), an indexed price (like the Elliot Lake Uranium Mines and Mary Kathleen), or a floor price (as in Lornex, Bougainville and Rossing). Thus the Company believed that any financial failure would have been due to poor management or technical

Jan 1, 1985

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,&apos; or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

By George H. Hanna

THE importance of the Donets coal field (the Donbas) to the national economy of the Soviet Union is well known. Great as was the significance of this tremendous deposit of coal in prewar days it is destined to become an even greater factor in the economic life of the country now that the tremendous havoc wrought by the Germans is being remedied. Since the war began, new coal fields have been extended; for example output of the Moscow and Karaganda (Kazakhstan) fields has become considerably larger while new mines are producing coal in several parts of Uzbekistan and Kirghizia. The huge West Siberian coal field, the Kuznetsk Basin, is producing more coal than ever before to supply the industries of that region and of the Urals. But so great has been the development of industry to meet war needs, especially in those districts of the Soviet Union that lie to the East of the Urals, that the coal obtained, eked out by such locally-won fuels as peat and wood, is still barely sufficient to meet industrial requirements. The main burden of the coal supply for the restored industries of the West, therefore, will fall on the Donbas.

Jan 1, 1945

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18&apos; API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By E. P. Pfleider, O. Rellensmann

In the May 1959 issue of [=] the authors reported on the gyrotheodolite as used for determining azimuths in surface and underground work. Further research has led to the development of a new type of gyro instrument, the band-suspended gyro attachment, which is essentially an upset gyro attached to the top of a theodolite. The new gyro attachment is light enough to be mounted on any angle-measuring instrument if the design of the telescope standard permits. Gyrotheodolite units have been used to transfer meridian lines underground in the Coeur d&apos;Alene mining district, although they have not been used extensively in the U.S. In other parts of the world, however, they have been adopted as the standard surveying instrument by mining engineers.

Jan 3, 1968

APPLICATIONS for loan contracts for the exploration, development and mining of strategic and critical metals and minerals are now being accepted by the Department of the Interior. The RFC is authorized and directed by Executive Order 10161 to make such loans but the Secretary of the Interior must pass on the necessity for the loan. Applications should be addressed to James Boyd, acting deputy administrator, Defense Minerals Administration, Department of the Interior, Washington, D.C. rather than to the Field Offices of the Bureau of Mines as was first planned. Application forms are not yet available but it has been learned that data accompanying the application should include the known quantity and grade of reserves, the anticipated rate of production, the equipment, supplies, and man power required for the additional production, etc.

Jan 12, 1950

POSITIONS VACANT No. 255. A company manufacturing malleable iron fittings in Connecticut needs a manager for its steel department. Experience with converter is essential. No. 256. A prominent mining company in Central America wishes a shift boss for its mill and cyanide plant, who is technically trained, experienced, and can speak Spanish. He should he sufficiently expert to be able to take entire charge of the mill in case of emergency. Salary $150 per month on a two years&apos; contract, with additional allowance for board, lodging and transportation expenses. No. 257. A Mexican copper mining company in the State of Puebla needs an engineer on surveying and mapping and drafting in connection with field construction. Healthy locality. Salary $150 per month.

Jan 1, 1918

By William P. Blake

At the August meeting of the Geological Society of America, I presented a paper on the occurrence of alunogen and bauxite upon the Upper Gila river, about 40 miles north from Silver City, New Mexico, together with observations upon the geology of that region." Inasmuch as the subject is specially interesting to metallurgists and mining engineers, and as our Transactions contain recent important papers, by Dr. Hayes, M. Laur, of France and others, upon bauxite, I venture to offer to the Institute, in more condensed form, an account of the deposits described in the paper above referred to. The only other published account of the alunogen locality which I have been able to find is a prospectus-pamphlet, issued in a small

Jan 1, 1895

By Charles J. Speake, Dennis R. Haley, Thomas E. Finch

The tremendous interest in development of surface- mineable coal throughout the western US will bring with it a requirement for many manhours spent in mine planning and equipment selection. One problem in particular that engineers face during the planning stage is that of selecting a dragline with the proper reach capability. Reach, expressed in terms of operating radius and effective spoil radius, can be a major problem when mining deeper than originally planned, and aside from production requirements, the ability of a particular dragline to spoil across a strip is essential. Determination of dragline reach needed for a multiple-seam western coal operation can be simplified by use of an equation derived below that eliminates the need for tedious and repetitive calculations.

Jan 5, 1977