Search Documents

By R. Stefanko, R. H. King, L. A. Morley

Coal mine fires, injuries and electrocutions, and many production delays have resulted from trailing cable splice failures. Research was carried out at The Pennsylvania State University to determine the failure causes and recommended solutions. The study revealed that current splice kit materials are generally adequate with the exceptions of connector flexibility, adhesives bonding, and abrasion characteristics of taped jackets. Research indicated that the most prevalent breakdowns result from workmanship defects. Therefore, guidelines for improved splice construction are reported in detail.

Jan 1, 1976

By W. J. McGee

Most nations and states have conducted geological surveys, generally with the view of discovering and developing natural resources, sometimes with the aim of promoting science. In some cases, as in the first survey of Pennsylvania, the official geologist so far preceded the prospector and miner as to guide the discovery and exploitation of the commoner ores, mineral fuels and structural materials; but in most instances statesmen have only been awakened to the need of such a survey by the successful extraction of minerals;

Jan 1, 1893

By William P. Blake

The phenomena of concentric arrangement of minerals in rock-masses, generally known as " orbicular structure," have of late received much attention from investigators. Lawson, of the University of California,' has described the orbicular gabbro at Dehesa, San Diego county, Cal. Kessler and Hamilton, of Stanford University, working independently upon the same subject, published their descriptions,2 giving also a list of many other localities in Europe and America where orbicular rocks are found, adding copious references to the literature of the subject.

Jan 1, 1906

By Fred W. Gordon

The heading of this paper was prompted by the knowledge that experience, up to this time, seemed to indicate that smaller furnaces were preferable for smelting the material of this section. Since the reasonable success thus far achieved by the first furnace of this plant tends to change the above opinion, and unsettle the generally-accepted views of furnace-men as to "weak " coke, a few words as to the design of the plant and the mode of operation adopted may prove interesting.

Jan 1, 1889

Jan 1, 1961

By A. B. Stevens, C. J. Coberly

The absolute porosity of a rock or sand may be defined as the volume of the interparticle space expressed as a percentage of the total rock volume. The effective porosity as contrasted with the absolute porosity is the volume of the interparticle spaces which intercommunicate with passages of sufficient size to permit the entrance or recovery of gas or oil, also expressed as a percentage of the total rock volume. A knowledge of effective porosity is of prime importance in estimating the ultimate recovery to be expected from oil and gas-bearing formations. The determination of the effective porosity of a rock includes the measurement of two values: (I) the volume of the rock as a whole, and (2) the volume of the grains and sealed pore space. This paper deals with a new apparatus which has been called a "hydrogen porosimeter" for determining the volume of the grains and the sealed pore space. This volume is determined by means of the pressure relations established in the instrument by the introduction of a known quantity of hydrogen. The Hydrogen Porosimeter The apparatus used in this work consists of an upper chamber for measuring the gas, a lower chamber for holding the sample to be tested, a gage for measuring the pressures, a tank of hydrogen, and the necessary connections. (Figs. 1 and 2.) Of the several gases that might be used for this work, hydrogen has been chosen for three reasons: (1) it deviates less from the gas laws than most gases; (2) it readily penetrates the sample; (3) it is absorbed less than most gases by the solids and liquids with which it may come in contact. Method of Operation After placing the sample to be tested in the lower chamber, the apparatus is thoroughly flushed with hydrogen to remove all air from the system, which is then brought to atmospheric pressure Po. The valve connecting the two chambers is next closed and the pressure in the upper chamber is brought up to a pressure PI by admitting gas from the tank.

Jan 1, 1933

By Edward W. Parker

This plant was built in 1907 at the Bankhead mines to manufacture briquettes by the Zwoyer process under license from the Zwoyer Fuel Co., of New York, N. Y. The building was constructed to contain two units, each of a capacity of 10 tons per hr.; one unit was installed at the time the building was constructed, and the second unit is now being built. The coal used is an anthracite, which is more friable than that of Pennsylvania, and, as a consequence, a larger percentage of dust or waste is produced, which was formerly thrown upon the slack-pile as waste, but is now passed to the ? dust-bin " in the breaker, from which it is conveyed to the briquette-plant.

Jan 5, 1908

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy's law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy's law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy's law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933

By AIME AIME

AS one of his friends asserted at the Galveston meeting last fall, T. V. Moore is one of the "thinkers" in his field. He is head of production research for the Humble Oil & Refining Co., with headquarters in Houston. He is also known in the Institute as a "doer" for his active participation in the affairs of the Petroleum Division and for his leadership in the formation of the present Gulf Coast Section, A.I.M.E.

Jan 1, 1940

Jan 1, 1969

By L. W. Casteel

St. Joseph Lead Company's Southeast Missouri mines have been successfully converted to the use of ammonium nitrate and fuel oil as a blasting agent. This is significant to the company because it means a savings of a quarter of a million dollars per year. It is significant to the mining industry because of the unusual conditions involved and the methods and materials used to overcome them. St. Joe has been mining the low grade lead deposits of southeast Missouri since 1864. This ore occurs as disseminated galena in widely scattered pockets within the Bonneterre dolomite. The daily production of 20,000 tons is obtained from several hundred small, room and pillar stopes covering an area 10 miles long and five miles wide. Distribution of explosives and other materials is a real problem. Drilling in the stopes is done with air legs, column- mounted machines or jumbos, depending on the size and location of the stope. Drill hole sizes vary from 1 3/8-in. diam down to 1 1/8-in. Each driller charges his own holes and shoots them at the end of the shift. Numerous shafts provide natural ventilation which is supplemented in isolated areas by churn drill holes equipped with blowers. Water, in most stopes, is not a serious problem, although the mines do produce about 20,000 gpm.

Jan 5, 1962

By L. G. Austin

If S (x) is the specific rate of breakage of size x and B (x, y) (see Table 1 for Nomenclature) is the cumulative breakage distribution function, the Herbst Fuerstenau2 assumption is that Inserting this assumption into first-order grinding equations it has been shown" that there are then simple analytical solutions to the grinding equations, as shown in Table 2. In this context "plug flow" is defined as all material passing through the mill in the same length of time, the residence time t. The term "n fully-mixed" means that the mill has a residence time distribution" which can be treated as if the mill were n equal fully mixed sections in series. In addition it has been shown that the assumption of Eq. 1 also leads to simple analytical solutions for closed-circuit, steady-state grinding with an ideal classifier at the mill exit returning oversize to the mill feed. The solutions are also given in Table 2, with µ as the ideal classifier cut size, C the circulation ratio, and Q (x) the size distribution of the circuit product. The specific surface area of these size distributions is where the density-shape factor k. is assumed to be constant with size. In practice, most methods of size analysis or area [ ] measurement have a finite lower limit, so that the integration is really performed from xm, to xm, For a realistic degree of grinding the value of So is dominated by the fine sizes because of the 1/x factor. Consider batch grinding of a feed of size y to y + dy. The batch grinding solution given in Table 2 is then [ ] The fresh surface area produced is the area of the fines plus the area of the original material remaining minus the area of the original material, [ ] Little error is introduced by neglecting the last term on the right-hand side since at t = 0 it is zero, and when t is significant the first term dominates because of the fine sizes produced. In addition, the form of P (x, t) for [ ] realistic values of S (x) 2t ax° is such that the major fraction of fresh surface produced is contained within the bottom 10% of weight of broken material, that is, for sizes for which P(x, t) < 0.1 (providing y is not near x.,). Thus for surface area purposes Eq. 3 can be approximated by [ ] becomes providing again that the feed sizes are coarse relative to xmi. Then the fresh area production is and W is the mass in the mill. The rate of surface production is WK, and the specific surface is Kt. From Table 2, the specific energy is mt/W so surface production per unit energy is [ ] Surface produced per unit energy input = KW/m (8) where m is the energy input of the mill. Clearly, identical reasoning applies to open-cycle, plug-flow grinding, with t replacing t, and Eq. 8 is obtained again. Considering open-cycle, fully mixed grinding, similar reasoning gives P(x) - t S(x) for surface area purposes, and

Jan 1, 1974

By W. H. Burke

Deeper drilling, resulting in greater circulating distance and pressure, has directed attention to the advantages of the study of properties and control of rotary muds, which until recently have not had much consideration. One fundamental property of muds is viscosity, and viscosity is influenced by the quantity and character of colloidal material and can be controlled by chemical treatment. Colloidal Matter of Rotary Muds Two types of colloids are found in muds; the hydrophobic and the hydrophilic. Hydrophobic colloids do not associate intimately with water and are sensitive to small quantities of electrolytes. Hydrophilic colloids associate intimately with water, but are not so sensitive to electrolytes. The colloidal particles of rotary muds are derived from clay; In clay the particles may range in size from submicroscopic to macroscopic; a substance is a clay if the greater proportion of the particles are within the size limits prescribed for clay. The larger particles are inert and have no effect on the viscosity of normal hydrophobic colloidal muds. There are two theories accounting for the colloidal properties of clay-water suspensions: (1) the physical theory, that clay in water is a coarse colloidal suspension, and (2) Ashley&apos;s1 theory, that clay is a granular material with a colloidal gel surrounding the crystalline grains. The most important colloidal substances known to exist in clays besides the clay particles are: (1) colloidal silica, (2) colloidal alumina, (3) colloidal ferric hydroxide, (4) colloidal silicates, and (5) colloidal organic matter. Plasticity, a peculiar property of clay-water suspensions, is due to the colloidal particles. It is commonly (although not with strict accuracy) measured in terms of viscosity, and depends upon the amount and the state of flocculation of the colloidal matter present in the suspension. Fluidity in a rotary mud may be caused by a lack of colloidal clay particles or by deflocculated or flocculated clay particles, while viscosity in a

Jan 1, 1935

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By M. Muskat R. D. Wyckoff

The phenomenon called "water-coning" is that, observed in many oil wells, in which bottom water gradually and frequently sudderlly displaces a part or all of the oil production when a certain rather critical production rate from the well is exceeded. To follow in detail the process of the formation of a water cone as it breaks through the oil zone and enters the well bore is a problem so complex as to make a theoretical analysis practically impossible. However, an analytical treatment of the flow system before the water has broken through and during the time that it lies statically beneath the oil zone with an elevated or "coned" surface can be carried through under certain approximations. To present an analysis which shows the essential characteristics of the coning mechanism is the purpose of the present discussion. Physical Basis of Theory and Meaning of Approximations As will always be true for flow systems where true water-coning is at all possible, the water will be supposed to lie beneath the oil zone because of its density contrast with respect to the oil. In fact, tinder the usual field conditions, when the pay horizon is reasonably homogeneous, the water most frequently enters the well through the lower zones, but even when it enters from intermediate zones it may, in the later life of the well, displace the bottom layers of oil, thus resulting in a system wherein the oil is effectively floating on the water.

Jan 1, 1935

By H. K. Shearer

There were no important developments in the oil and gas industry in South Arkansas during 1935. Oil production, totaling 11,138,340 bbl., continued the decline that has been normal since 1925, but the decline from 1934 was only 278,600 bbl., or 2.5 per cent. The principal decline was in the Smackover field, while only the Champagnolle and Garland City fields showed notable increases. More wells were drilled than in any recent year, with a total of 123 completions. There were 44 oil wells, with a total reported initial daily production of 10,013 bbl., or an average of 227 bbl. per well. Two small gas wells were completed in Union County, where the gas is used locally for pumping and field operations. There were 77 dry holes, of which 28 were in or near oil fields and 49 were wildcats. Active drilling oper-at&apos;ions declined from 65 at the beginning of 1935 to 41 at the end. Most of the drilling was done during the first part of the year, espr-chially (luring the flurry caused by the discovery late in 1934 of the "Taylor" sand production in the Champagnolle field, but the producing area was soon outlined. In November, 1935, the J. E. Crosbie, Inc., NO. 1 Sullivant in sec. 12, 17s. 14W., producing 560 bbl. per day at 3175 ft., opened a new sand lens in the eastern part of the field. The Camden "oil field," discovered in the last week of 1934, remained a one-well field, although four offset tests were drilled, besides a number of others in the immediate vicinity. Several interesting deep tests were drilled during the year, which added a great deal to the general knowledge of the subsurface formations and the structure of south Arkansas, but were not particularly encouraging as to prospects for the very deep production. First, the H. L. Hunt, No. 15 E. F. Gregory well in sec. 10, 17S., 14\W., in the Champagnolle field, was drilled to a depth of 6911 ft. It pene-trated red beds for 2982 ft., from 2943 to 5925 ft., mostly if riot entirely of Lower Cretaceous age. There was some anhydrite in the last 135 ft. of red beds. This was followed by 890 ft. of limestone, probahly Permian, and the rock salt was struck at 6815 ft. The salt is now generally conceded to be of Permian age. Finding salt in this well strongly indicates

Jan 1, 1936

By H. K. Shearer

There were no important developments in the oil and gas industry in South Arkansas during 1935. Oil production, totaling 11,138,340 bbl., continued the decline that has been normal since 1925, but the decline from 1934 was only 278,600 bbl., or 2.5 per cent. The principal decline was in the Smackover field, while only the Champagnolle and Garland City fields showed notable increases. More wells were drilled than in any recent year, with a total of 123 completions. There were 44 oil wells, with a total reported initial daily production of 10,013 bbl., or an average of 227 bbl. per well. Two small gas wells were completed in Union County, where the gas is used locally for pumping and field operations. There were 77 dry holes, of which 28 were in or near oil fields and 49 were wildcats. Active drilling oper-at&apos;ions declined from 65 at the beginning of 1935 to 41 at the end. Most of the drilling was done during the first part of the year, espr-chially (luring the flurry caused by the discovery late in 1934 of the "Taylor" sand production in the Champagnolle field, but the producing area was soon outlined. In November, 1935, the J. E. Crosbie, Inc., NO. 1 Sullivant in sec. 12, 17s. 14W., producing 560 bbl. per day at 3175 ft., opened a new sand lens in the eastern part of the field. The Camden "oil field," discovered in the last week of 1934, remained a one-well field, although four offset tests were drilled, besides a number of others in the immediate vicinity. Several interesting deep tests were drilled during the year, which added a great deal to the general knowledge of the subsurface formations and the structure of south Arkansas, but were not particularly encouraging as to prospects for the very deep production. First, the H. L. Hunt, No. 15 E. F. Gregory well in sec. 10, 17S., 14\W., in the Champagnolle field, was drilled to a depth of 6911 ft. It pene-trated red beds for 2982 ft., from 2943 to 5925 ft., mostly if riot entirely of Lower Cretaceous age. There was some anhydrite in the last 135 ft. of red beds. This was followed by 890 ft. of limestone, probahly Permian, and the rock salt was struck at 6815 ft. The salt is now generally conceded to be of Permian age. Finding salt in this well strongly indicates

Jan 1, 1936

By S. S. Clarke

THEN sufficient ore has been blocked out on a lease to warrant a shaft, the proposed. Location of the shaft should be carefully considered, as the old promoter&apos;s method of sinking wherever his hat landed is a sad mistake as some: of us have learned by trying to operate such mines. In some instances certain conditions exist, such as mill location, railroad right of way, etc., that necessitate a change of location from the. ideal, but under average conditions and with the knowledge of the formation gained from the drill logs and with the general trend of the orebody known, the shaft can be located from. the standpoint of its future relation to the mine with re-gard to hauling and&apos; hoisting a maximum tonnage: at a minimum cost per ton, also taking into account the minimum amount of expense and trouble- in sinking. Quite a few shafts are located in the wall of a run or just in the thin edge of the orebody: As a general rule the formation here is solid and permits rapid and safe sinking, and the shaft pillars are left in practically valueless material. This permits the withdrawal of pillars and still keeps the shaft protected. By opening a shaft in thin ground, you are not tempted to cut it high, wide, and handsome, but to shape it up-with ample clearance for lay-bys and with more of an idea of permanency, as a few hundred extra dollars spent around the shafts for proper track installation will re-turn, a good rate of interest in ease of handling "cans," quick get-away; and fewer wrecks. Nearly all the shafts in this district are sunk on a contract basis, the con-tractors furnishing all labor and explosives, and the company building the sinking-derrick, dump-track, and furnishing, all equipment, material, and power. The following costs are the averages, for three shafts sunk through good solid formation, with no water to, contend with, and approximately 260 -ft., deep, having about-100 ft. of shale. The contract price was $9 per foot with the shale and $13 per foot in the solid, making a total of $2,980 paid to the contractor. The wages paid by the contractor were, $5 per shift for the hoist-man, who also sharpened steel, $6 for the lead shaft man, and $5 for the helper;, the cribbing was sawed on contract for 40c. per shaft: foot; about. 94 board feet. of cribbing was used per foot of staggered cribbing and 168 board feet per foot of solid cribbing.

Jan 8, 1928

By T. A. Klinefelter, O&apos, R. G. Meara, Glenn C. Truesdell, Richard W. Smith

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for&apos; aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.&apos; With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By T. A. Klinefelter, R. G. O’Meara, Glenn C. Truesdell, Richard W. Smith

THE investigation of domestic tales was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. I, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." HISTORY The use of steatite and talc in ceramic bodies goes back a great many years. If pure, tales shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a large business was carried on in the manufacture of tips for gas burners.1 With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Manchurian tales. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1943