Search Documents

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,' we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943

By J. Weertman

An explanation is advanced for the recent results of Barrett and Sherby on the high-temperature creep of fee metals. Their measurements indicate that metals with a low stacking fault energy creep at a much slower rate than metals with a high stacking fault energy. The explanation is based on the assumption that the rate of core diffusion is much smaller in partial dislocations than in perfect dislocations. An experiment is suggested to test this assumption. The explanation also requires that the jog density is small on widely split dislocations. SHERBY and Barrett1,2 recently established an important result in the field of high-temperature steady-state creep. They have shown that fee metals whose dislocations split into partial dislocations separated by a wide stacking-fault ribbon creep at a much slower rate than fee metals whose dislocations are not split appreciably. The creep rates in the two cases may differ by a factor as high as 6000. (For the purpose of comparison, the test temperature of each metal was chosen so that its rate of self-diffusion was equal to a standard value. Similarly the stress levels were such that the ratio of the stress to an appropriate elastic modulus was the same for each metal. In all cases the stresses were sufficiently low that the steady-state creep rate was proportional to the stress raised to a power.) It is the purpose of the present paper to attempt an explanation of this interesting and significant result of Sherby and Barrett. The activation energies of high-temperature creep of the metals tested by Sherby and Barrett (aluminum, nickel, copper, and silver) were equal to their self-diffusion activation energies. Hence it appears reasonable to assume that this type of creep is controlled by a dislocation-climb process, which in turn is controlled by the diffusion of vacancies to or from dislocation lines. (It will be assumed that the diffusion of interstitial atoms is unimportant in the climb process. The analysis could be repeated for the case in which interstitial atoms are important.) In prior papers374 I have treated dislocation climb by using the assumptions that core diffusion is extremely fast down a dislocation and that a dislocation always maintains an appropriate vacancy concentration in its immediate vicinity. In this

Jan 1, 1965

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which" are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing' together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because not more. than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By J. Kent Smith

The object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent; furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575" F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450" F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450" F.) were reheated for varying periods of time at 575" F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943

By J. P. Doan, G. Ansel

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By Welton Crook

UNLESS present in considerable proportion, metals of the precious-metal group-other than gold and silver-are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipi-tate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the pre-cipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,1 in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bis-muth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez con-tains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donite, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana' says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most refer-ences on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1939

By David J. Mack

The structures and properties of the copper-aluminum alloys have been the subject of much study since the classic investigation of Carpenter and Edwards1 focused attention on. the engineering utility of these alloys. It was recognized at an early date that the metallographic structures developed in the aluminum bronzes were similar to those developed in steels, both in the annealed and the rapidly cooled state. Most investigators have been concerned with the acicular, martensitic-like structure formed from the 0 solid solution upon rapid quenching; the transformation of the ß under equilibrium cooling to a lamellar eutectoid having been relatively neglected. With the introduction in 1930 by Davenport and Bain2 of the isothermal transformation technique for studying eutectoidal decompositions, a new field was opened. Although an enormous amount of work has since been done on the isothermal transformation of steel, study of structurally analogous systems has been almost totally overlooked. The outstanding exception was the prize-winning paper† of Smith and Lind1ief³ ho investigated the decomposition of the 0 phase in copper-aluminum alloys by isothermal methods. This was followed in 1934 by Wasserman's review' of available information on analogous transformations in eutectoid alloys. Since that time no comprehensive study of isothermally transformed eutectoids analogous to steel has appeared, although many valuable contributions have been made to an understanding of the structures developed in such systems. Important papers have been published by Kurdjumow, Gridnew and co-workers, Obinata,18.'9 Greninger,20.21 and Others. The work to be described in this paper was an outgrowth of preliminary studies on the isothermal transformation of a entectoid aluminum bronze, after it became apparent that the alloy under study was reacting somewhat differently than the similar alloy used by Smith and Lindlief. Preliminary Experiments The material used in this study was a high purity aluminum bronze especially prepared by Ampco Metal, Inc. It analyzed: Copper—88.07 pet, Aluminum—11.89 pct, Iron-—0.02 pet, Manganese—-.OI pct, Others—Balance. Although some disagreement exists on the exact composition of the eutectoid, this alloy was believed to be of essentially eutectoid composition even though some pro-eutectoid* delta particles existed in the microstructure of furnace cooled specimens. Specimens transformed isothermally at temperatures slightly below the eutectoid showed relatively large amounts of pre-eutectoid delta, but as will be shown later, this results

Jan 1, 1949

By A. Chakravarti, C. C. Harris

First-order kinetics adequately describe the recovery of a single floatable species. The conditions under which cell behazior can be simulated by a single-phase model are discussed; deviations from the multiphase model are accountable. The rate coefficient depends upon operating conditions besides particle size and mineralogy and the physicochemical properties of the pulp constituents. The model for a real flotation system combines the first -order, single-phase model with a distribution of noninteracting species. Methods for determining the distributions are discussed. Applications of the procedure to flotation studies are outlined. The mathematical description of flotation as a rate process can be traced to Garcia1 who reported cases in which the fraction of solid remaining in a cell in semi-batch operation, F (for Notation used throughout, see Table l), decays exponentially with experimental time T. F = e-k>r. (1 The differential equation leading to Eq. 1 is dF ----= -k,F (2) dT which is recognized as the algebraic analog of the chemical kinetics first-order reaction equation.' This has led to suggested mechanisms for flotation and mathematical relationships other than first order: with very little foundation other than analogy. The flotation rate coefficient kl can be accounted for as the product of several probabilities concerning bub-ble-particle attachment and detachment, aggregate entry from pulp into froth and return from froth to pulp, and removal from froth as concentrate. These factors clearly contribute to the magnitude of the overall flotation rate, and there are others also, but describing flotation merely as the overall probability of consecutive gross events hardly appears a significant advance in understanding. More recently, it has been described in terms of a stochastic process, which promises to provide a more satisfactory approach? The present paper will be more concerned with a phenomeno-logical description of the flotation process than with an account of the internal mechanics of the process. This is not a statement of priorities, or a judgement of the relative importance of these options but rather an assessment of what is presently possible. Previous investigators'" have developed methods for interpreting semi-batch flotation data in terms of species distribution. These methods have been used in an attempt to explain flotation behavior in response to changes in operating conditions." Inspection of examples given in the literature" reveals discrepancies between theory and experiment, and data obtained in the Colum-

Jan 1, 1971

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep¬resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geological Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is, one of the most important minerals, was omitted because not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By W. J. Taylor, H. J. Mutz, A. F. Brock

THE International Kickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody. Two pits were opened at the Frood-Stobie mine; the Frood section was started in 1938 and the Stobie section in 1942. To meet the heavy demand for nickel during World War 11, open-pit production was accelerated until it constituted over 40 pct of Inco's total tonnage. As a consequence open-pit ore was depleted considerably alhead of schedule; the Stobie pit was completed in the summer of 1951, and it is expected that mining at the Frood pit will be completed in 1953. The major program launched 10 years ago to develop additional underground production as a replacement of open-pit tonnage thus had to be greatly speeded up. This conversion to all-underground mining will be completed within the next two years, and the underground mines will then have an annual hoisting capacity of 13,000,000 tons. One of the new mines in the underground expansion program, the Murray, was brought into production in 1950. Ore production from the new Stobie section of the Frood-Stobie mine was commenced on a limited scale in 1951 and will be increased as the program progresses. Delivery of ore to the new Creighton mill was started in the summer of 1951 from the caving project launched at Creighton mine. When mining was started in the Sudbury district 65 years ago the ore deposits were opened on a small scale and mining methods conformed to a general pattern of small open cast pits, followed by open stopes as mining was extended below the pits. The open stoping methods used were heading-and-bench and shrinkage. In certain cases a type of cut-and-fill mining was used with drywall tramways and dry-wall chutes in the fill. As the mines were deepened,

Jan 1, 1954

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By David J. Mack

THE structures and properties of the copper-aluminum alloys have been the subject of much study since the classic investigation of Carpenter and Edwards1 focused attention on the engineering utility of these alloys. It was recognized at an early date that the metallographic structures developed in the aluminum bronzes were similar to those developed in steels, both in the annealed and the rapidly cooled state. Most investigators have been concerned with the acicular, martensitic-like structure formed from the ß solid solution upon rapid quenching; the transformation of the ß under equilibrium cooling to a lamellar eutectoid having been relatively neglected. With the introduction in 1930 by Davenport and Bain2 of the isothermal transformation technique for studying eutectoidal decompositions, a new field was opened. Although an enormous amount of work has since been done on the isothermal transformation of steel, study of structurally analogous systems has been almost totally overlooked. The outstanding exception was the prize-winning paper† of Smith and Lindlief3 who investigated the decomposition of the ß phase in copper-aluminum alloys by isothermal methods. This was followed in 1934 by Wasserman's reviews of available information on analogous transformations in eutectoid alloys. Since that time no comprehensive study of isothermally transformed eutectoids analogous to steel has appeared, although many valuable contributions have been made to an understanding of the structures developed in such systems. Important papers have been published by Kurdjumow, Gridnew and co-workers, 5-17 Obinata,18,19 Greninger,20,21 and others .22.28 The work to be described in this paper was an out-growth of preliminary studies on the isothermal transformation of a eutectoid aluminum bronze, after it became apparent that the alloy under study was reacting somewhat differently than the similar alloy used by Smith and Lindlief. PRELIMINARY EXPERIMENTS The material used in this study was a high purity aluminum bronze especially prepared by Ampco Metal, Inc. It analyzed: Copper-88.o7 pct, Aluminum-11.89 Oct, Iron-0.02 pct, Manganese-0.01 pct, Others-Balance. Although some disagreement exists on the exact composition of the eutectoid, this alloy was believed to be of essentially eutectoid composition even though some pro-eutectoid* delta particles existed in the microstructure of furnace cooled specimens. Specimens transformed isothermally at temperatures slightly below the eutectoid showed relatively large amounts of pre-eutectoid delta, but as will be shown later, this results

Jan 1, 1947

By A. F. Taggart

This paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water. Apparatus The pneumatic table used is shown in Fig. 1. Deck A is 20 by 12 in. and consists of nainsook supported on slats that register with the riffles. Fig. 2 is a photomicrograph of the nainsook used. It shows that the cotton threads average about 0.13 mm. dia. and the apertures about 0.17 mm. The deck carries 12 riffles consisting of wooden strips, 3/16 in. wide and 1/4 in. high, laid parallel to the feed side of the table. The riffles terminate along a line starting on the feed side at a point 11 in, from the mechanism end and running to the corner formed by the coal side and slate end. Taper starts from a line that runs parallel to their terminal line through the junction of the upper riffle with the mechanism end. The height at the terminal line is about 1/32 in. The deck with its supporting slats is carried on a framework consisting of rails A, sloping end rails B, and adjustable metal strips C, which latter permit variation in transverse slope. This frame is enclosed at the edges by means of heavy canvas, indicated in the sketch by wavy lines, which makes a flexible conduit between the deck and the stationary air chamber,

Jan 1, 1930

By J. Kent Smith

THE object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent, furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575° F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450° F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450° F.) were reheated for varying periods of time at 575° F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By AIME AIME

BBENJAMIN LEROY MILLER, of geology at Lehigh since 1907, is known the world around, for his former students are on every continent. He knows the earth is round for he has encircled it twice, once in 1927, and the other way around in 1937 to regain the day he lost on the first trip. An early trip was to Great Britain and Ireland, another to central Europe, a third to Spain for the International Geological Congress, a fourth to Scandinavia. His trip to the Southern Hemisphere is recorded in "Mineral Deposits of South America." In 1940 he was booked for Australia but because of the war went instead to Alaska. He spent the summer of 1941 in Central America. Thus he has gained a broad. world knowledge of mineral deposits, both metallic and nonmetallic.

Jan 1, 1942