Search Documents

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By Henry Wurtz

Jan 1, 1880

By Thomas H. Leggett

IN speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining-practice, since this has been already well described both in the Transactions1 and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a. whole, marking its general development and the lines of its future progress. In a. paper entitled Deep-Level Shafts on the Witwatersrand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,3 presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (1:). 975): "In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discussed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy was vitally necessary for both 1 Gold-Mining in the Transvaal, South Africa, John Hays Hammond, xxxi., S17 to 855 (1901). R Engineering and Mining Journal, vol. lxxxv., p. 53 (1908). ' Trans., xxx., 947 to 987 (1900).

Jan 5, 1908

By Henry Wurtz

HERACLITUS, a sage of antiquity, called the dark philosopher, who refused a throne, preferring a hermit's cell, propounded, twenty-four centuries since, the maxim : [ ] War (or strife) engenders all things. This, though probably intended by Heraclitus to apply especially to the internal forces of nature, is often said, with equal reason, of the affairs of men. Controversial strife, whether fortunately or unfortunately, is a crucible through which all new discoveries in science, and all technical applications of science must pass-a test which they must all endure before they can become so vitalized as to germinate, so to speak, take root in the human mind, grow tip, and overspread the earth. The greater the number and the power of the elements arrayed against such a growth, and of the influences hostile thereto, the greater should be the inherent vitality of the germ, the more strenuous, skilful, and persistent its cultivators and upholders. During the decade last past we have had, in spite of the severe stringency of the times, an active growth of this kind in progress, whose prospective importance it would now be difficult to overrate. This is the movement which has for its motive the idea that, generally speaking, fuel should be gaseous in form, and which has for its goal the introduction into general public use of gaseous products, made by cheap and rapid processes and on a gigantic scale, distributed throughout our cities and towns in distribution-systems which shall be proportionately gigantic, and sold at prices which will bring such fuel within the means of the poorest householders. Personally, for ten years past, the writer has never failed, on occasions public or private, to urge his belief that the realization of this idea, deemed by him a certainty of the future, will bring about

Jan 1, 1880

Important chemical and other technical engineering work necessary, for the prosecution of this war is being carried on by the Bureau of Mines Experiment Station, at Washington, D. C. The services of trained men of the following classifications are urgently needed Bacteriologists Instrument makers Biologists Laboratory Assistants Chemists, Inorganic Laborers Chemists, Organic Machinists Chemists, Physical Physiologists Chemists, Electro- Plumbers Chemical Engineers Steamfitters Draftsmen Stenographers. Electrical Engineers Skilled labor of various kinds If your training fits you for any of these occupations, send to the Bureau of Mines, American University Experiment Station, . Washington, D. C. for blank forms. When properly executed and returned by you, these forms will be placed on file, and when a vacancy occurs you will be considered for it and will be notified if your services are desired. If you are a registrant in the draft, and have not yet been- ordered to camp, it may be possible to have you immediately inducted into the service for work here. If you are not in the draft, but feel that you wish to serve your country in the present crisis, you can enlist, or serve as a civilian. Serve your country where you can serve it best. VAN H. MANNING, Director.

Jan 6, 1918

By K. P. Wang, Virgil L. Barr

The U.S. Minerals Attaché Program, similar to the scientific and technical attache programs of other industrialized nations, is designed specifically to keep surveillance on significant worldwide developments in minerals, metals, and fuels. Knowledge of international minerals developments is essential for both domestic planning and conduct of foreign affairs. CONTROLLED BY DEPT. OF STATE Ten minerals specialists-eight minerals attaches and two petroleum attachés-man this far-flung, worldwide program for the U.S. Government as best they can. Minerals attach& also handle oil, in posts lacking petroleum attaché. The legislative authority for the Minerals Attaché Program is the Foreign Service Act of 1946 and succeeding amendments and Presidential Executive Orders. Therefore, this program is controlled by the Department of State. Interior (representing the Bureau of Mines) and State collaborate in policy formation and direction by means of a "memorandum of agreement" which covers establishment of posts, selection of officers, contents of reports, and supplemental training. State also has about half a dozen nonspecialist officers to complement the work of the minerals and petroleum attaché. It is not the intention here to evaluate the administrative arrangements of this program but rather to describe it and to provide examples of the important job it is doing.

Jan 11, 1965

By Howard M. Graff, Sidney C. Bouwer

The economics of mining has traditionally been viewed quite apart from the economics of blast furnace operations. It was realized, of course, that blast furnaces would operate best with good raw materials, but the shipping grade of ore, for example, was decided by a sort of collective bargaining process between the ore producers and the blast furnace operators. The mine operators had to keep their costs down, and were usually successful in convincing management that the ore in any particular deposit was endowed by nature with a certain iron content and that the mine grade could not be raised beyond a certain economic limit. The blast furnace operators would have liked a better grade, but as long as they were able to make a fairly good showing it was more or less accepted that they had to take the ore as it came. The mine operators were able to ship to the nation's blast furnaces thousands of tons of iron ore that would be completely unacceptable by present-day standards. As late as the early 1950's, the major steel companies were witnessing an actual decline in the iron content of their incoming ore supply as the mining companies mined progressively leaner material and upgraded it only enough to pass competitive market requirements

Jan 8, 1965

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By Philip McKenna

WHEN a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be con-sidered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essen-tial wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool, materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered.

Jan 1, 1938

By G. C. RIDDELL

THE metallurgist, chemist, and physicist are blazing trails that lead far afield. Pushing on into an "Alloy Age" they see a non-ferrous era over- taking iron and steel. Delving into the nature of the physical world, they break down a supposedly indivisible element, hydrogen. Not content with terrestrial problems, they peer back along the cosmic ray into iaterstellar space, glimpsing forces that are, apparently, still busy with the task of atom-making. Mastering and organizing the material and physical, they advance steadily toward that borderland of science where the concept of matter itself seems abandoned, and force is the substance left.

Jan 1, 1930

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By William D. Southard, Joseph W. Schlitt, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott 's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12-15% moisture could be consistently delivered for smelting.

Jan 1, 1980

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By Thomas H. Sheldon

IN the zeal for opening up new ore-bodies, or for. extracting the ore from attractive bodies gal ready opened up, we very often lose sight of the fact, that, after all, the operation of a mine is a business proposition, pure and simple; and for the best working-results should be treated upon a strict business basis. Of course, in every mine of consequence a record is kept of expenditures and receipts, and such glittering generalities as "gross receipts," " net receipts," " mining expenses," .and " per cent. profit," can be told to the cent; but does this . record show economy of management, either as compared with the same record of other months, or as compared to the record of other mines of the' same class ? Moreover, if such a record shows that the cost of mining is high, does it in any way en¬able the manager to put his finger on the leakage? Does it necessarily follow that a mine which makes a profit of, say, 40 per cent on 25-dollar ore, is doing less economical mining than one which saves 60 per cent on 80-dollar ore ? Of course the figures in the latter case look the more attractive, but when it comes to a point of saving everything which can be saved, and of cutting down expenses to the lowest possible cost of operation, the former mine is doubtless on the most firm and economical financial basis. But as the relative merits of the system of mining in the two cases, nothing could be decided without a basis of detailed comparison ; if one system is more economical than the other, why is it so, and wherein does the advantage lie ? This can be shown only by keeping accurately the cost of each mining operation. And no matter how dissimilar two mines may be in character and operation, yet there are a few general heads common to all mining operations. In the first place, it is necessary to break the ore from the solid ground ;

Nov 1, 1905

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927

By Jan Visman, S. J. Aresco

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all the layers of coal and impurities found in the seam as well as portions of the stratas above and below the coal seam. The preparation plant is the device to size, crush, and/or remove impurities so the coal may be shipped as a salable product. Sampling may be needed at many stages in the preparation process. Although this chapter is primarily concerned with sampling in connection with preparation processes, the principles apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1) To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained, or monitoring raw coal delivered to the plant. 2) To check the performance of various operating units in the plant, either by float. and sink tests or chemical analyses. 3) To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in US Bureau of Mines (USBM) publications by J. A. Holmes,l G. S. Pope,2 and A. C. Fieldner.3 The American Society for Testing and Materials (ASTM) more or less adopted the methods proposed by USBM in their Standard D-21-1916 and it remained a standard for many years. Briefly, this standard called for a 500 lb (227 kg) sample for coals less than 94 in. (19 mm) in size and a 1000 lb (454 kg) sample for all coals over 94 in. (19 mm) in size. No mention was made of increments, but there was an instruction that the sample should spread over the coal

Jan 1, 1979

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By Stewart Murray, Philip Klapwijk

INTRODUCTION Forecasting commodity markets is like predicting winners in a horse race: to get the answers right, one needs both luck and judgement. Commodity analysts bear some resemblance to racing tipsters as they try to convince interested parties that they have an inside track on which metal is going to win the great minerals race of the 1990s. Commodity analysts share some features with the gentlemen of the turf: • They influence other people in how to spend risk capital, • They don't put their own money at risk, and • If their tips consistently fail to deliver, then they end up looking elsewhere for employment. In order to find winners we need to know about the kind of race we are in and the strengths and weaknesses of all the runners. Miners are not interested in a five furlong sprint: their race is a long distance affair -- after all, the lead-times between discovery and start-up generally approach a decade for mines that will provide the staying power which leaders require in this industry. We need to look at the environment in which our commodities will be competing: in racing parlance, the going. Our equivalent is the economic background: just as some horses are at a relative advantage when the going is soft, so some commodities will do better than others if economic growth is sluggish. If we are going to pick the winners for the late 1990s, and as an industry, make the right investment decisions, nothing is more important than being able to forecast (with at least a semblance of accuracy) how and where the world's economy is going to develop in the next decade. In addressing the question of whether minerals are going to be leaders in the 1990s, this paper considers the idea that it will increasingly be the world outside the industrialised OECD that will provide the incremental growth in demand for mineral products. Economic growth in the Developing World is fundamentally different from that in the OECD, and the pattern of demand for materials in relation to economic output is much more favourable than in the OECD. If we are to forecast the future, we need to be able to understand the past, both in the boom times of the so called Golden Sixties and in the lean years that followed them. This should help us to decide whether the future is going to be like one or other of these extremes or, on the other hand, a return to normality. Having forecast the going, we can look at individual competitors. • Which are best placed to take advantage of the economic, social and industrial trends that we can now dimly foresee? • Which can resist the continued onslaught of the new materials and technologies? • Which of them will best weather the economic storms (assuming that recessions have not yet been abolished)? If we can provide answers to these questions, we will be well on our way to picking winners, i.e., the metals and minerals that will reward their owners with growing demand, steady (and high) prices leading to profits beyond the dreams of avarice.

Jan 1, 1990

By Elmer W. Pehrson

OPINION seems widely divergent as to where we stand with respect to future mineral supply. From some quarters we hear that the United States is about to become a "have-not" nation and about to experience the evil consequences such a situation would entail. Others claim that we are still a treasure house of stored-up mineral wealth, the surface of which barely has been scratched. The data to be presented here support the conclusion that neither of these viewpoints is correct and that we are far from exhaustion of those mineral resources that are basic to our industrial economy. However, exhaustion is well advanced in a number of important subsidiary minerals so that we can no longer drift along with the easy-going philosophy that the earth will provide. The time has come when we must recognize the true situation and do something about it.

Jan 1, 1945

By A. Springer

Chemists, physicists and others, whose occupations necessitate the use of fine scales, have heretofore regretted their inability to obtain any which would remain uniformly accurate. The difference between the theoretical and the actual results obtained in the ordinary balance (provided the pivot-distances are exact) is mainly due to the frictional resistance between the knifeedges and their bearings. This frictional resistance, although reduced to a minimum in the finest scales when new, constantly increases, thereby decreasing the sensitiveness proportionately. When examined under the microscope, neither the surface of the knife-edge nor that of' its hearings ever appears perfectly smooth. Soft kunife-edges are easily blunted, whereas hard ones are brittle and liable to crumble under the effects of over-load or shock. Prof. Frederick A. Roeder for many years attempted to discover some means by ,which the knife-edge could be replaced with some device free from the above-mentioned objections. His experiments convinced him that a torsion-joint was best suited for that purpose. After he had communicated his conclusion to me, we jointly developed the system to its present form. A torsion-wire had been used for the centre of rotation, prior to Prof. Roeder's invention, but it was found impossible to replace the terminal knife-edges with torsion-joints.

Jan 1, 1884