Search Documents

By Joseph Kelly

DEPLETION of anthracite resources in Lackawanna County, Pennsylvania, has forced the recovery of coal tracts formerly considered unminable. Chief among these are the large areas of outcrop coal lying on a heavy pitch on the mountain sides, abandoned thirty or forty years ago as too costly and too hazardous to mine. The old companies, in many instances, stopped their chambers 80 or 100 ft. hack from the actual outcrop, and then dropped back another 100 ft. before starting to rob the pillars, thus leaving large areas of coal. Recovery of this coal naturally leads to mining hazards not encountered years ago. The first step is to sink a slope from the surface with the pitch of the vein, and then drive counters across the pitch as close to the robbed area as proper protection for the lower side of the -counter will permit. Next, the old chambers are advanced or new ones driven in the solid, as the conditions require. As these chambers approach the outcrop the real safety work begins-that of preventing the miner from being buried or locked in by an avalanche of mud.

Jan 1, 1936

The attached tables show that in 1935 production of crude oil in Poland slightly decreased (minus 14,450 tons) and that gas production

Jan 1, 1936

The attached tables show that in 1935 production of crude oil in Poland slightly decreased (minus 14,450 tons) and that gas production

Jan 1, 1936

By L. M. Howe, J. Gordon Parr, E. Saarema

THE decreasing solid solubility limit at the titanium-rich end of the Ti-Cu constitutional diagram,' Fig. 1, suggests the possibility that titanium-rich alloys may be age-hardenable. However, results obtained by Holden et al. reproduced in Fig. 2 show that after quenching from 790°C the age-hardening of an alloy containing 1.7 pet Cu is very slight, while a 0.8 pet alloy decreases in hardness, during heat treatment at 400°C. It was believed possible that powder samples of alloys might show different results from the lump samples used by Holden et al., since small particles are often more sensitive to diffusion processes than larger samples. Consequently, a 1.9 pet (by weight) Cu alloy was made by the technique of levitation melting," checked for homogeneity, and filings of 48-65 Tyler screen size were cut from it for aging experiments. The filings were helium-quenched (by a technique described previously)' from 790°C, sealed in vacuo in silica tubes and aged at temperatures of 400°, 450°, and 500°C. Microscopic and X-ray examinations failed to reveal any structural changes during the aging process. This is not too surprising since early stages of precipitation do not usually manifest themselves in ways that are readily detectable by metallographic methods, and the extent of precipitation on overaging a 1.9 pet alloy is very small. However, hardness readings (taken on a Bergs-man micro hardness tester, using a 25 g load applied to a diamond indenter) do show a hardness peak at each aging temperature, Fig. 3. About a dozen readings were taken on each heat treated sample; the highest reading and the lowest reading were ignored and an average taken of the remaining values. In

Jan 1, 1957

By Newell Alford

AT its meeting in the fall of 1937, the Executive Committee of the Coal Division considered the growing scarcity of young engineers entering coal mining with serious intentions. This scarcity was the cause of con-siderable alarm and a committee consisting of C. T. Hayden, E. A. Holbrook, C. E. Lawall and L. E. Young, with the writer as chairman, was appointed to gather factual data on the current trend. A questionnaire1 was designed and mailed to the heads of the 60 mineral technology schools listed by Prof. W. B. Plank in his article in September 1937.2 Replies were received from 46 institutions, not all from heads of coal-mining courses but all from men that at one time or another have had experience with some kind of coal-mining curricula and know current student impressions. Our committee is indebted to all of these gentlemen for their cooperation. Our committee hoped by this means to quickly reach the root of the trouble and make a set of comprehensive recommendations to the Coal Division for relieving the industry immediately from the growing dearth of youth who yearn for coal-mining careers, but the condition is more serious than at first diagnosed. We must now refer the question back to the Coal Division, with the recommendation that the Division get the industry's permission for still another major operation on its frame of mind. In addition to 10-year statistics on the first pay received by graduates in coal mining and other technical work, we requested enrollment data for 20 years from all schools with either mining engineering or mineral technology curricula. Nine leading questions were also plied, as shown in the Appendix. Every one of the answers was significant and inter-esting. Fortunately, we encountered positive frankness that was extremely helpful.

Jan 1, 1938

By Norman Goss

IT is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.1-8 The broadening of the K. lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the dif-fraction lines are broadened and the K a doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolu-tion of the doublet is lost when a metal is cold-worked and the Lane spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attrib-uted the hardening to fragmentation of the grains into smaller units.

Jan 1, 1940

W. G. MATTESON, Houston, Tex.-I think that Mr. Powers has given us some very valuable information on the Healdton field, which is of material interest in view of the fact that the Healdton field has passed Cushing in the point of production, and if not leading, stands second only to the new El Dorado field in the point of production of the oil-in this country. Mr. Powers says that the deepest producing sand at Healdton is 1860 ft. Within the last 3 or. 4 months they have drilled to 2700 ft. there and found a sand which is producing very high-grade oil, if I remember correctly, about 42 gravity. Another very important point brought out by Mr. Powers is the fact that the Pennsylvanian beds and the Permian beds are conformable according to his interpretation. He seems to have based his interpretation upon the gathering of a number of well logs and a very careful study of them, but it seems to me the information furnished by the, well logs is really insufficient to justify such an important conclusion. In the first place, the difficulty of interpreting the line of demarcation between the Permian "Red Beds" of Oklahoma and the top of the Pennsylvanian is apparent, for the reason that sometimes the uppermost Pennsylvanian formation has a reddish phase and the line of demarcation is not very sharp.

Jan 4, 1918

By Teh-Yu Kao, Don J. Wood

With the increasing industrial use of the method of transporting solids by fluids through pipes, a better understanding of the basic mechanics of a solid-liquid pipe flow system is essential. In this study the phenomenon of incipient motion of solid particles resting in a sediment bed on the bottom of a pipe is investigated. Since a system would fail to operate at the designed solid-liquid flow condition if it was not capable of operating through the transient initial flow phase, information concerning the starting transient is of great interest. An objective definition of incipient particle motion, derived from energy considerations, is first proposed. Using this the critical state is defined to describe the flow condition during which a solid particle can at least temporarily escape the sediment bed and move in the liquid. Postulated also in this study is that the condition of incipient motion can be reasonably well predicted by a consideration of particle equilibrium in a direction normal to the pipe axis. The incipient condition is considered to occur at the instant the force between the bed and the particle, normal to the pipe axis, is zero. Experimental measurements of incipient conditions are obtained for water flowing through a horizontal pipe with sand sediment beds of different thickness. These are compared to predicted values with good agreement.

Jan 1, 1975

By John A. Emery, Frank G. Snyder

Mining geology has a threefold objective: to guide prospecting for new ore, to evaluate known orebodies as development risks, and to supply the detailed knowledge of ore structures necessary for more economical extraction. The role of geology in exploration is well established. This article will deal solely with orebody evaluation and the application of geology to development and mining problems as practiced by St. Joseph Lead Co. in the southeast Missouri district, which for many years has supplied approximately 30 pct of U. S. lead production. The primary concern of the present discussion is geology in the district, not geology of the district. The southeast Missouri district, locally called the Lead Belt, includes parts of St. Francois, Madison, and Washington counties. The first recorded mining was about 1720 at Mine La Motte in Madison County on surface showings of lead ore. Later discoveries near Bonne Terre, twenty-five miles to the north, led to extensive prospecting and underground mining. To date the district has yielded well over 8 million tons of pig lead, valued at more than $1 billion. By far the greater part of the lead production has come from an area of 50 sq miles, centering Fig. 1-Central portion of southeast Missouri on the city of Flat River, as shown in Fig. 1.

Dec 1, 1956

By L. O. Bond, R. P. Alger, A. W. Schmidt

Well logging provides valuable information for planning coal mining operations. In addition to locating, defining, and evaluating coal beds, electrical logs indicate the relative competence of roof and floor formations. Electrical well logging is the .recording of various physical, chemical, or physicochemical properties of the strata penetrated by a drill hole. To perform logging operations, borehole measuring probes, or sondes, are lowered on a cable into the drill hole. Insulated conductors in the cable pass power to the sonde and transmit signals to the surface. As the sonde is pulled up the hole, the measurements are recorded as a well log. These measurements serve to define the formation lithology. Common rock minerals exhibit characteristic log values such that computer analysis of the log data defines the mineral content of the formations. Shales, carbonates and sandstones, and coal beds are readily distinguished. Furthermore, preliminary results in coal studies indicate the log data delineates variations in ash and moisture contents. Of major concern in planning mining operations is knowledge of roof and floor competence. Here again the logs provide valuable information. Measurements of formation density and acoustic wave velocity provide data for computation of a compressional modulus. This compressional modulus is an effective index of formation competence. Electrical logging thus efficiently provides information for economic planning of mining operations.

Jan 1, 1972

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By G. J. Harmsen

is shown that in any isotropic porous medium there is a fixed ratio, : , between the numerical valrles of the total pore perimeter per unit of cross-section and the specific surface area per unit of bulk volume. The consequences of this fact on the use of the concept "hydraulic radius" in the case of porous media are examined. The validity for consolidated sands of Kozeny's rela- tionship and of the formula derived by Carman for capillary rise are discussed. INTRODUCTION In the course of time several quantities and relations have been put forward in order to describe the texture of a porous medium and the flow of fluid through it. Among these relations the so-called Kozeny formula and a formula for capillary rise, for both of which Carman',' has given a derivation, will be specially considered here. These relations are of a semi-empirical nature and the derivations must be considered to have a heuristic significance only. For unconsolidated mate-

Jan 1, 1956

By N. Mao

This paper presents the results of a research effort to develop a technique for estimating in situ stresses by measuring stress-induced velocity anisotropy around a borehole. Relevant parameters required to make the estimate were identified and measured in the laboratory on a 35.6 cm (14.0 in) cube of Nugget sandstone with a 10.2 cm (4.0 in) diameter hole, under biaxial loading. Two pairs each of radially and tangentially polarized transducers were placed inside the hole with displacement directions either parallel or perpendicular to the principal stress directions. With this configuration, relative travel times were measured by both a pulsed phaselocked loop technique and a cross correlation of digitized waveforms. The biaxial velocity data were used to back-calculate the applied stress. The standard deviation of the differences between the calculated and applied stresses is 0.62 MPa (90 psi) for a stress level up to 8.63 MPa (1250 psi).

Jan 1, 1984

By Joseph P. Hodgson

JOSEPH P. HODGSON.-As to ".Safety First," I did not deal with that, but I will say that in 1913, the number of .men killed was nine, and that year the "safety first" program was commenced; the next year, 1914, the number was reduced to five. In 1915, I am pleased to say that the number was reduced to two in the Copper Queen's entire property, and we have none so far this year. THE CHAIRMAN (G. F. G. HERMAN, Bisbee, Ariz.).-I can say, further, that we have from eight to nineteen men per month incapacitated for more than 14 days. Those are classified in this State as serious accidents. The number of men injured has apparently increased, -but that is clue to our improved method of recording and classifying accidents, no matter how slight. C. W. GOODALE, Butte, Mont.-The importance of cooperation among the members of the staff of an industrial organization is well brought out by Mr..Hodgson's paper.

Jan 12, 1916

During the latter part of the Civil War an income tax was placed upon coal and the production of coal in the various collection districts during the life of this tax is shown in the tabulation that follows. The counties that include coal deposits are shown for each district. No record exists now of the production by counties, but it is calculated here on the basis of tax collected. The table, of course, does not include any territory not under the control of the northern armies, and not all of that in some cases.

Jan 1, 1942

By Barton K. Cross, Ronald J. Sparks

The question of' providing training for miners in the United States has been answered by Public Law 95-164, which stipulates not only that the mine operator will provide training, but generally how much and what material will be covered. At an operation employing 500 miners, the eight-hour refresher training requirement will necessitate an annual investment of over two man-years in labor, a figure that does not include the time spent in training new hires and job transfers. Such an investment can and should be cost effective, while catering to miners' needs.

Jan 6, 1979

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of area prior to urban development population and aggregate consumption trends in Austin, TX, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby areas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1982

By Dennis V. D’Andrea, Joseph L. Condon

Laboratory crater tests were performed in two-dimensional plates and three-dimensional .blocks of Holston Limestone. Fractures in the blocks were exposed by sawing through the crater region, and a technique employing dye penetrants is described for examining the resulting fracture systems in both blocks and plates. Crater fracture patterns changed from extension of radial fractures to spa11 fractures parallel to the free face as charge depths were increased. The amount of fractured rock was found to be greater than the amount determined from standard crater volume measurements. Graphs and photographs illustrate these findings.

Jan 1, 1971

By Phillip E. Butler

The Pennsylvania Dept. of Transportation is actively engaged in the utilization of coal mine refuse in the construction of highway embankments. Long-held objections for utilization are invalidated by research, laboratory data, and construction performance. Laboratory, engineering, construction, and environmental impact analyses are presented from the construction of the Cross Valley Expressway embankment at Forty Fort, Luzerne County, Pa. Comparisons of laboratory data and construction measurements are given. The refuse embankment is the first of its size in Pennsylvania, and possibly the U. S., covering 1.5 million cu yd.

Jan 1, 1977