Search Documents

By J. W. Downey, M. V. Nevitt

The phase boundaries for the 950" isothermal sections in the ternary systems Zr-Co-0 and `Zr-Ni-0 have been determined for the composition range from 50 to 100 at. pct Zr. The two systems show very similar phase relations, having no extensive solid solution phase fields. Each contains a ternary phase. These phases are apparently isostructural, but their structure has not been determined. Some aspects of the phase relations are discussed in terms of the alloying behavior of transition metals. THE work described in this paper is the outgrowth of a recent study of the occurrence of phases having the Ti2Ni-type structure (structure-type E9,) in certain ternary systems involving Ti, Zr, or Hf with another transition metal and O.", In the Zr-CO-0 and Zr-Ni-0 systems no Ti2Ni-type phases were found to occur. However, there are several interesting aspects of the phase relations in the two systems which have significance from the point of view of the alloying behavior of transition metals. The results of this investigation may also have some importance in studies of the oxidation of Zr-Co and Zr-Ni alloys. In both the Zr-Co-0 and Zr-Ni-0 systems only the 950" isothermal sections were investigated and, as a further restriction, the study was limited to the composition range from 50 to 100 at. pct Zr. A tentative Zr-Co binary diagram has been published by Larsen, Williams, and Pehin. In the composition range pertinent to the present work they report a eutectic at 980°C and 75.9 at. pct Zr, the products of which are the terminal solid solution based on /3 Zr and the compound Zr2Co, and a eutectic at 1080" and 64.8 at. pct Zr whose products are Zr,Co and ZrCo. The solid solution based on /3 Zr is shown to decompose eutectoidally at 826°C into a Zr and Zr2Co. The limits of solubility of Co in a and /3 Zr have not been established. The structure of Zr2Co is not identified in the publication just cited. Dwight has reported that ZrCo has the CsC1-type strcture. The Zr-rich portion of the Zr-Ni diagram has been determined by Hayes, Roberson, and Paasche." The phase relations are very similar to those of the ZrCo system. A eutectic reaction whose products are /3 Zr containing 2.9 at. pct Ni and Zr,Ni occurs at 961°c, and a eutectic between Zr,Ni and ZrNi is found at 985". The solid solution based on /3 Zr decomposes eutectoidally at 808°C. The solubility of Ni in a Zr is not known accurately but is believed to be very small. Smith, Kirkpatrick, Bailey, and Williams7 have found that Zr2Ni has a tetragonal structure of the A1,Cu-type and that ZrNi is orthorhombic. Domagala and McPherson8 have published a constitution diagram for the system Zr-ZrO,. At 950" their diagram indicates that the solid solution of 0 in 0 Zr is stable from 0 to 0.5 at. pct while the phase field of 0 in a Zr extends from 6 to 29 at. pct. These solubility limits were adopted in the present study and no binary Zr-0 alloys were made. No previous data on the phase diagrams of the ternary systems are known to exist. EXPERIMENTAL PROCEDURE The experimental details involved in the preparation of alloys in this laboratory by arc melting have been described in several previous papers"3 and they will not be repeated here. Information concerning the purity of the metals used is given in Table I. Oxygen was added in the form of reagent grade ZrO,. All of the cast specimens in both alloy systems were annealed in air-atmosphere tube furnaces at 950 3' for 72 hr and water quenched. The specimens were protected from oxidation by wrapping them in Mo foil and sealing them in quartz tubes that had been evacuated at room temperature to a pressure of 1 x 10B mm of Hg. The phase boundaries were determined by metallography, and identification of the phases was accomplished primarily by X-ray diffraction methods which employed a powder camera having a diameter of 114.6 mm. The diffraction techniques which are in use in this laboratory have been previously described.' An etchant that proved satisfactory for most of the alloys consisted of 5 pct by vol of AgNO

Jan 1, 1962

By F. I. Grace, L. E. Murr

The mechanical responses and residual defect structures in 70/30 brass and type 304 stainless steel following explosive shock loading and cold reduction by rolling have been studied. A distinct relationship was observed to exist between the residual mechanical properties and micro structures observed by transmission electron microscopy. Shock-loaded brass deformed primarily by the formation of coplanar arrays of dislocations and stacking faults at lower pressures, and twin-faults (deformation twins and €-martensite bundles) at higher pressures (> 200 kbar). The micro -structures of cold-rolled brass were characterized by dense dislocation fields elongated in the rolling direction. Stainless steel was observed to deform by the formation of dense arrays of stacking faults at lower shock pressures and twin-faults at high shock pressures (>200 kbar). Lightly cold-rolled stainless steel deformed similar to low Pressure shock-loaded stainless steel, but transformed to a' martensite in heavily cold-rolled stainless steel. Discontinuous yielding was observed for the heavily cold-rolled stainless steel, and stress reluxution in the weyield region for cold-rolled and shock -loaded stainless steel was interpreted as an indication of the ability of twin-faults and stacking faults to act as effective barriers to dislocation motion. A simple model for the formation of the planar defects and a' martetnsite is presented based on the propagating of Shochley partial and half-partial dislocations. A considerable effort has been expended over the past decade in an attempt to elucidate the response of metallic-crystalline solids to the passage of a high velocity shock wave (e.g., smith,' Dieter,2 and zukas3). While it has been possible to obtain relevant information pertaining to the residual defect structures and mechanical properties, there have been few rigorous attempts to draw a direct comparison between these structures and properties. In addition, numerous investigators have recently observed the occurrence of deformation twinning in shock deformed fcc metals (e.g., Nolder and Thomas,4 and Johari and Thomas5), but little attempt has been made to elucidate the mechanisms of formation of these defects. Comparative data for metals deformed by shock-loading and the same metals deformed by more conventional modes of deformation such as cold-reduction by rolling is also generally lacking. The present investigation therefore has the following objectives: 1) to examine the mechanical properties of some explosively shock loaded and cold-rolled fcc metals of low stacking-fault energy as a function of their residual substructures; 2) to present a simple model for the formation twin-faults and related defect structures in the low stack-ing-fault energy materials of interest (70/30 brass, ySFg= 14 ergs per sq cm; and 304 stainless steel, ySF = 21 ergs per sq cm); 3) to make some deductions with regard to the residual characteristics of dislocation and planar defect substructures in cold rolled and shock loaded 70/30 brass and type 304 stainless steel. In particular, it was desirable to characterize the residual hardening effects of particular deformation substructures. I) EXPERIMENTAL PROCEDURE Sheet samples of 70/30 brass (0.005 and 0.15 in. thick; annealed at 659°C for 2 hr) and type 304 stainless steel (0.007 in. thick; annealed 0.25 hr at 1060°C) of nominal compositions shown in Table I were cold-rolled in one direction only to produce reductions in thickness of 15, 30, 45, 60, and 75 pct in the brass; and 5, 15, 25, 35, and 45 pct in the stainless steel. Identical sheet samples in the annealed (unrolled) state were subjected to plane compressive shock waves to various peak pressures ranging from 0 to 400 kbar in the brass and 0 to 425 kbar in the stainless steel; and with a constant peak pressure duration of approximately 2 microseconds. A detailed description of the shock loading technique has been given previously.6 Tensile specimens 1.0 in. in length and 0.125 in. in width were cut from the cold-rolled sheets (tensile axis parallel to the rolling direction), and the shock-loaded sheet specimens. Stress (load)-strain (elongation) measurements on the tensile specimens were made on a Tinius-Olsen load-compensating tensile tester using a strain rate of 2.7 x 10-3 sec-1. Tensile tests were repeated at least twice, giving essentially the same results. Stress relaxation measurements in the preyield region were also made using an initial strain rate of 5.4 x 10-4 sec-1. In addition to tensile and stress relaxation measurements, Vickers microhardness measurements were made on all samples. A total of 100 microhard-ness readings were obtained for each specimen following a light electropolish to ensure uniform surface conditions for all tests. The hardness averages ob-

Jan 1, 1970

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By George S. Ansell, Thomas E. Davidson

It has been known for a considerable period of time that the ductility of even quite brittle materials can be enhanced if they are deformed under a superposed hydrostatic pressure of sufficient magnitude. The response of ductility to pressure, however, has been shown to vary considerably between materials. Prior work has shown that the effects of pressure upon the tensile ductility of Fe-C materials depend upon the amount, shape and distribution of the brittle cementite phase. In this current investigation, the effects of pressure upon the fracture mechanisms in a series of annealed and spheroidized Fe-C materials were examined. It was observed that the principal effect of pressure is to suppress void growth and coalescence, retard cleavage fracture and to enhance the ductility of cementite platelets in pearlite. Based upon the observed effects of pressure upon the fracture mechanisms, a proposed explanation for the enhancement in ductility by pressure and for the structure sensitivity of the phenomena is presented and discussed. THE effect of superposed pressure upon the tensile ductility of a variety of metals has been well documented.'-'' Some of the results from several investigators are summarized in Fig. 1 where tensile ductility in terms of true strain to fracture (ef) is plotted as a function of the superposed pressure. As can be seen, a pressure of sufficient magnitude can significantly enhance the ductility of metals. However, Fig. 1 also demonstrates that the response of ductility to pressure and the form of the ductility-pressure relationship varies considerably between materials. Several explanations have been offered for the observed enhancement in ductility by a superposed pressure. Although no experimental evidence was provided, Bridgman13 and Bobrowsky10 proposed that the observed effect was due to the prevention or healing of microcracks or holes. Bulychev et a1.14 observed that cracks and voids in initially prestrained copper were healed in the necked region of a tensile specimen upon further straining while under a superposed pressure. Also, pugh5 observed that large cavities were suppressed in copper fractured in tension while under pressure. A second proposal has been forwarded by Beresnev et at al.6 This proposal is based upon the hypothesis that a material fails in a brittle manner because the normal tensile stress reaches a critical value before the shear stress is of sufficient magnitude to cause plastic flow. Since a superposed hydrostatic pressure will increase the ratio of shear to normal tensile stress, a sufficiently high hydrostatic pressure should favor plastic flow while retarding brittle fracture. Galli15 reported that a superposed pressure shifts the ductile-brittle transition temperature of molybdenum. This was explained based upon the reduction of the normal tensile stress by the superposed pressure. Pugh5 explained the occurrence of the observed pressure induced brittle-to-ductile transition in zinc in the same manner. Davidson et al.12 proposed an explanation for the enhancement of ductility by pressure based upon the effects of pressure upon the stress-state-sensitive stages of various fracture propagation mechanisms. Basically, they proposed that pressure will retard cleavage and intergranular fracture by counteracting the required normal tensile stress or will suppress void growth. They observed suppression of intergranular fracture and void growth in magnesium by pressure. Davidson and .Ansell16 reported ductility as a function of pressure for a series of annealed and spheroidized Fe-C alloys. Fig. 2, from this prior work, demonstrates that the effect of pressure upon ductility is structure sensitive in terms of the amount, shape and distribution of the brittle cementite phase. As shown in Fig. 2, in the absence of cementite or when the cementite is in isolated particle form (spheroidized), the ductility-pressure relationship is linear and the slope decreases with increasing carbon content. In the annealed carbon-bearing alloys wherein the cementite is in the form of closely spaced platelets (pearlite) or in the form of a continuous network along prior aus-tenite boundaries (1.1 pct C material), ductility as a function of pressure is nonlinear (polynomial relationship) in which the slope increases with increasing pressure. At the highest pressures studied (22.8 kbars), the slope of the curves for these materials tends to approach those for the spheroidized material of the same carbon content. In this current investigation the change in fracture mechanisms as a function of pressure for the materials shown in Fig. 2 has been examined. The possible connection between the observed effects of pressure upon the fracture mechanisms and the effect of pressure upon ductility is discussed.

Jan 1, 1970

By J. B. Conway

Stress-vuptuve data for several of- the refractory metals are frequently found to yield a linear relationship between the Larson-Miller parameter and the logarithm of the applied stress. In such cases linear stress-rupture isotherms result with slopes bearing a definite relationship to the temperature. It also follows that the stress to produce rupture in a certain period of time will be linear in temperature. Data for several refractory metals have been reviewed and excellent linearity is shown in this type of isochronal plot. In addition, the af ore - mentioned lineavity leads to a linear relation between the log of the stress to produce rupture in a certain time and the homologous temperature. This has been illustrated for the Group VI-A metals, tungsten and molybdenum. EXTENSIVE use has been made of the Larson-Miller' parameter in the interpolation and extrapolation of stress-rupture and creep data. In those cases where this particular parametric approach is applicable a convenient and fairly straightforward procedure is made available for the correlation of experimental stress-rupture data. It is quite common to employ this parameter in the form of a master rupture plot in which the parameter, T(C + log tr), is expressed as a function of log stress. In many cases this functional relationship in log stress is linear within acceptable accuracy and hence the following relation results: where P is the parameter, C is the Larson-Miller constant, T is the absolute temperature, t~ is the rupture time, a is the stress, and a and b are constants. Examples of such a relationship are contained in the work of Green, Smith, and 01son2 dealing with high-temperature rupture behavior of molybdenum and in the work of Green' dealing with the high-temperature behavior of tungsten. In addition, pugh4 has shown a similar linearity for some fairly low-temperature data for molybdenum. It can be shown that when the relationship in Eq. [I] is exhibited certain generalizations can be made concerning the form of the stress-rupture isotherms. For example, rearranging yields: For a given material (constant C) at a given temperature the first term on the right-hand side of Eq. [2] is a constant and hence this equation defines a straight line when log stress is plotted as a function of log-rupture time. This is recognized as the standard form usually employed in this type of data presentation. Such linearity then suggests the linear form of the Larson-Miller parameter. Or, in other words, the linear parametric relationship in Eq. [2] results only when the stress-rupture data are linear on a log-log plot of stress vs rupture time. Another interesting observation can be made in regard to Eq. [2]. It can be noted that the slope of the stress-rupture isotherms is given by - T/b and hence a direct calculation of the constant b is available. It also follows that since the value of b is the same for all temperatures the slopes of the various isotherms on the log-log stress-rupture plot cannot be the same. Indeed, the existence of the relationship in Eq. [2] precludes a system of parallel lines on this common stress-rupture plot. As a matter of fact it further specifies that in addition to being nonparallel the slope of these isotherms must decrease (i.e., become more negative) with increasing temperature. Such a condition is indeed found to exist in the case of the stress-rupture data reported for molybdenum.' As a corollary to the above, it may be stated that stress-rupture data which do not lead to a linear log-log stress-rupture plot or whose isotherms do not exhibit a decrease in slope as the temperature increases will not yield the linear relationship of Eq. [I]. Applying Eq. [2] to two different temperatures and solving for C yields: Eq. [3] affords a simple and rapid method for calculating the Larson-Miller constant from the log-log stress-rupture plot. The slope of a given linear isotherm is measured and the value of "b" calculated based on Eq. [2] as: slope = - -Tb Then at an abscissa value of 1.0 hr (making log tr in Eq. [3] equal to zero) read the stress corresponding to rupture for two different temperatures. Substitution in [3] yields: A value of the Larson-Miller constant can thus be calculated from a few simple mathematical procedures employing data read directly from the log-log plot of the stress-rupture data. Of course, it is not to be overlooked that the above reasoning has been based on the linear relationship of Eq. [I] being applicable. However, if as mentioned above the log-log plot is

Jan 1, 1967

By E. Buehler, H. J. Levinstein

The temperature ranges in which the three inter-metallic phases in the Nb-Sn system form have been determined and the composition and structure of two of the three phases has been established. The kinetics of the formation of Nb3Sn in cored wire samples has been studied in the temperature range of 800° to 1050°C. From 800°to 950°C the rate of formation increases by four orders of magnitude. The rate-controlling step for the formation process in this temperature range appears to be the diffilsion of tin through NbSn. At higher temperatu~es a change occurs in the mechanism of the formation process such that up to a temperature of 1050°C the rate of formation of Nb3Sn does not increase above the rate observed at 950°C. For temperatures helow 950°C the current-carrying capacity of the wire increases with increased percent reaction reaching a maximum value when the formation process is 90 to 95 pct complete. The maximum current-carrying capacity obtainable in this temperature range is independent of the temperature. Above 950°C tlze current-carrying capacity obtainable in the wire decreases with increasing temperature of formation. A model is proposed which accounts for the ohserved behavior. RECENTLY, Buehler et a1.l reported the results of an investigation of the process variables which influence the superconducting properties of Nb3Sn-cored wire. These results indicated that at least four variables affect the properties of the manufactured wire. These include composition, particle size of the starting powder mix, temperature of heat treatment, and time of heat treatment. In order to understand completely the role of these variables, it is necessary to have an accurate knowledge of the phase equilibria in the Nb-Sn system. At the present time, phase-equilibrium diagrams for the Nb-Sn system have been published by a number of investigators.2-5 The diagrams differ as to the number of phases present, the composition of the phases, and the temperature range of stability of the phases. The present investigation was undertaken in order to resolve these differences. Since the investigation of Buehler et al. demon- strated that the length of time at the temperature of heat treatment affected the superconducting properties of Nb3Sn, it is apparent that it is necessary to understand the kinetics of the formation process as well as the equilibrium conditions before a complete understanding of the system is possible. As a result, the kinetics of formation of the various phases in the system were also studied in this investigation. EXPEFUMENTAL PROCEDURE Diffusion couples and sintered powdered compacts were employed in the phase-diagram investigation. The diffusion couples were made by filling 1/8-in.-ID monel-sheathed niobium tubes with tin. The monel sheath was employed to facilitate drawing.' The tubes were then drawn to a tin-core diameter of 32 mils. Samples approximately 3 in. long were then cut from the drawn composite. The tin was drilled out of the ends to a depth of 1/4 in. and niobium-wire plugs were inserted into the ends and peened over. The monel was removed by etching in concentrated nitric acid, after which the samples were sealed in evacuated quartz bulbs and heat-treated in a resistance-wound tube furnace. The samples were quenched into ice water upon removal from the furnace. The diffusion couple samples were examined metallographically employing a chemical etching solution consisting of 10 ml of saturated chromic acid per g of NaF. In addition, two anodizing solutions were used for phase-identification purposes. The first was the picklesimer7 solution; the second consisted of equal parts by volume of 30 pct H2O2 and concentrated NH4OH to which 1 g of NaF was added per 25 ml of solution. The anodizing conditions for the second solution were 2 v and 100 ma with a tin cathode. The powdered compacts were made by pressing previously mixed powders of 99.9 pct pure Sn and 99.6 pct pure Nb supplied by the United Mineral Co. into cylinders 3/8 in. in diameter by 1/2 in. long. The cylinders were then sealed in quartz tubes and heat-treated in the same manner as the diffusion couples. The samples were examined metallographically and by X-ray diffraction techniques. Since it was desirable to be able to correlate the kinetic data with current-carrying capacity, the type of specimen chosen for this part of the investigation had to be a compromise between the optimum system for studying kinetics and one which was suitable for making current-carrying capacity

Jan 1, 1964

By W. R. Hansen, F. W. Boulger

Twenty-nine laboratory steels were studied to determine the effects of composition and ferrite grain size on drop-weight and Charpy V-notch transition temperatures. The experimental steels covered the following ranges in composition.. 0.10 to 0.32 pct C, 0.30 to 1.31 pct Mn, 0.02 to 0.43 pct Si, md nil to 0.136 pct acid-soluble Al. Although most of the data were obtained on hot-rolled samples, some plates were heat-treated in order to cover a wider range in ferrite grain size. The experimental data were used for a multiple-correlation analysis conducted with the aid of an electronic computer. The study showed that carbon raises and that manganese, silicon, aluminum, and finer ferrite grains lower both drop-weight and Charpy transition temperatures. Quantitatively, variations in composition and grain size have a more marked effect on V15 Charpy transition temperatures than on the drop-weight transition temperature. Useful correlations were found between transition temperatures in drop-weight tests and those defined by seven different criteria for Charpy tests. Evidence was accumulated that the conditions ordinarily used for drop-weight tests are more severe for 1-1/4-in. -thick plate than for 5/8- to 1-in. -thickplate. PROJECT SR-151, to study quantitatively the effects of metallurgical variables on performance in the drop-weight test, was established by the Ship Structure Committee late in 1958 on recommendation of the National Academy of Sciences, National Research Council. This project was initiated as a result of the increasing use of the drop-weight (nil-ductility) test in predicting the ductile-to-brittle behavior of steel. Qualitative data indicated the drop-weight was not as sensitive to metallurgical variables as the Charpy V-notch test. Furthermore, the available information indicated that the drop-weight test did not show the superiority of killed steels over semikilled steels reflected by Charpy tests. This difference in sensitivity to brittle fracture is considered important because the drop-weight transition temperature has been reported1 to correlate better with service-temperature failures than the V-notch test does at a constant energy level. Therefore, this project was concerned with establishing quantitatively the effects of metallurgical variables in the drop-weight test. For comparison, Charpy V-notch data were obtained for the steels investigated. This paper summarizes the results of the investigation. Most of the steels used for the study were made and processed in the laboratory. However, some tests were also made on commercial killed steels available from Project SR-139 (SSC-141). During the course of the investigation, data were obtained on the effects of carbon, silicon, manganese, and aluminum on transition temperatures of drop-weight and Charpy specimens. In addition, the effects of heat treatment which changed the ferrite grain size and the transition temperatures were also investigated. Finally a few exploratory studies were made on commercial killed steels to evaluate the effects of plate thickness, grain size, and heat treatment on the performance of drop-weight specimens. EXPERIMENTAL PROCEDURES Preparation of Materials. A total of twenty-nine 500-lb induction-furnace heats were made and processed in the laboratory for the investigation. Carbon, manganese, silicon, and aluminum contents were systematically varied. Melting and rolling techniques proven satisfactory in a previous project2 were used as a guide for the current investigation. Composition. The composition of the twenty-nine laboratory heats made for this project are given in Table I. The steels are divided into three groups. The first group consists of ten aluminum-killed steels similar in composition to Class C ship-plate steel. The second group consists of ten semikilled or Class B type steels. In both of these groups the carbon and manganese contents were intentionally varied over a wide range. This wide range in composition was helpful in obtaining quantitative data from a limited number of steels. The primary purposes of these two groups of steels was to determine the effects of carbon, manganese, and deoxidation practice. In addition, one steel in each group (Steels 2-2 and 9-2) were made about 1 year after the start of the program in order to check consistency of melting practice. The third group of nine steels listed in Table I was intended for studies on the effects of silicon and aluminum. In eight of these steels carbon and manganese were held relatively constant at levels of about 0.2 and 0.8 pct, respectively, while silicon and

Jan 1, 1963

By Frederic A. Delano

The subject of the wear of rails seems to have attracted an unusual amount of interest in the last six months, and in the bope of doing my share to direct opinions in what seems to me the right direction, I will attempt to discuss briefly the several ways in which the shape of the rail-section may affect the life of rails. In a paper presented at the Boston meeting of the Institute (Trans., xvi., 594),

Jan 1, 1889

By Alfred Weiss

Approximately 850 delegates from 24 countries met in Tokyo, Japan, May 24-27, for the second MMIJ-AIME Joint Meeting in 55 years, to exchange technical knowledge and experience in the fields of exploration, mining, metallurgy and petroleum engineering. The first such meeting was held in 1917 in Kyoto, Japan. Although the Mining and Metallurgical Institute of Japan was the sponsor, the entire meeting (machinery exposition, technical program, and tours) was a joint effort of the two institutes.

Jan 7, 1972

By D. J. Christie, W. C. Hellyer

Three autogenous grinding flowsheets were considered as follows: 1) Primary autogenous grinding of a -8-in, primary crusher discharge to produce a product suitable for second stage pebble milling, or a flotation feed product in a single stage of grinding. 2) Intermediate autogenous grinding in which +4-in. rock media is screened from the primary crusher discharge and employed as grinding media to grind a tertiary crusher product to flotation feed size in a single stage.

Jan 8, 1972

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand these has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of —200 mesh material in the final product markedly increases costs of de-watering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins. Wasting of coal in the -200 mesh slimes may account for a loss in washer yield equivalent to 2.0 to 2.5 pct of the raw coal input. With rising mining costs the value of such a loss is constantly increasing and a need for a better solution to the fines problem becomes more pressing every day. From an operating viewpoint, also, continuous removal of extreme fines from the washing plant circuit permits good water clarification practice, improving significantly the overall cleaning efficiency. The obvious desirability of recovering a commercially acceptable coal from washery slimes prompted U. S. Steel Corp. to investigate the merits of the Convertol process developed in Germany." Although this process has been used commercially in Europe for some time, little if any consideration has been given to its possible adoption in the U. S. until very recently. Fundamentals of the Convertol Process: In the Convertol process, droplets of dispersed oil are brought into intimate contact with the solids suspended in the coal slurry to be treated. This contact causes oil to displace the water on the surface of the coal by preferential wetting, or phase inversion, after which the coal particles are allowed to agglomerate in a manner permitting their re- moval from the slurry by centrifugal filtration. The clay and other particles of mineral matter suspended in the slurry do not have the affinity for oil the coal particles have. Consequently the oil treatment is preferential to coal to the extent that more than 95 pct of the oil used reports with the clean coal recovered. Figs. 1 through 3 will clarify the steps involved in the process. Fig. 1 shows the suspended material in the slurry to be treated, which is a thickened product containing 40 to 45 pct solids. Oil is now injected into the slurry under vigorous agitation to produce good oil to coal contact conditions, which result in preferential oiling of the coal particles. These coal particles are then permitted to agglomerate by gentle stirring in a conditioner to form flocs, as shown in Fig. 2. At this point in the process the agglomerated oiled coal can be washed and partially dewatered on a vibrating screen, as shown in Fig. 3. Finally, the washed flocculate can be further dewatered in a high-speed screen basket centrifuge or in a solid bowl centrifuge. Commercial Application of the Convertol Process in Germany: The original Convertol process was developed by Bergwerksverband zur Verwertung von Schutzrechten der Kohlentechnik, G.m.b.H., a German research organization controlled by the Coal Operators Assn. of the Ruhr Valley. The process as reduced to commercial practice in Germany' is shown in Fig. 4. In this process a thickened slurry (40 to 45 pct solids) mixed with a predetermined percentage of oil is fed from a surge tank to the phase inversion mill. After the phase inversion step, the slurry is usually discharged directly to a highspeed screen centrifuge. From 3 to 10 pct oil is used, depending on type of oil, size consist of coal to be recovered, and operating temperature. The top size of fine coal cleaned in Germany by the Convertol process is limited by the size of the openings in the centrifuge screen basket. Any mineral matter coarser than the basket opening, which is generally 60 to 80 mesh, must remain with the oiled coal. If the coal fines have been effectively cleaned down to about 80 mesh, the cleaning performance of the process is practically unaffected by the presence of coarse coal particles. However, since recovery of coal much coarser than 80 mesh is mow economical by conventional methods, it normally becomes more costly to allow substantial percentages of this coarse coal in Convertol process feed. Where the general plant layout does not permit effective cleaning of coal sizes down to 80 mesh or lower. there is some justification for a coarser Con-

Jan 1, 1959

By H. Sigurdson, C. H. Moore

Extensive studies have been carried out on electric furnace and blast furnace slags obtained in the winning of iron from its ores. These slags normally consist of elements of the gangue minerals present in the ores, as well as the added flux materials. In consequence, melts of CaO, MgO, Al2O3 and SiO2 can be considered as representing typical slag compositions. When a slag of this composition cools, it usually crystallizes according to predictions possible from an equilibrium diagram of these constituents, providing the melt is not undercooled to form glass. The melt is either viscous or fluid, depending upon the ratio of binary cations to silica, and crystallizes easily or forms a glass for the same reasons. If the melt is not overheated so that carbides of the metal components of the slag are formed and if the composition of the slag is so adjusted that it has a high fluidity, liquid equilibrium is attained and the slag can be held in a liquid state for extended periods of time. Upon tapping, the slag crystallizes into minerals, the type and proportion of which are determined by the melt composition. Since equilibrium is attained, the holding period is not critical. In melts containing a large increment of titanium, however, the normal slag procedures are not applicable. Titanium, as one of the atomic transition elements, is, at elevated temperatures, capable of being reduced to form metalloid compounds much more readily than the refractory oxides present in normal slags. In consequence, an oxide melt containing titanium never reaches equilibrium in a reducing environment, but continues to shift its composition until cooled. If melts of this nature are cooled and samples submitted to metal-lographic and X ray analysis the course of reaction and crystallization in this type of slag can be determined. Preparation of Slag The slags investigated fell into the system CaO-MgO-TiO2-Al2O3-SiO2 and were produced from ilmenite ores reduced by carbon in an electric furnace. Since the equilibrium series1 and the laboratory smelting of ilmenite2 are described in two of the accompanying papers, detailed description of the smelting procedure is not required here. However, certain essentials must be mentioned. Two types of melts were used to produce slags studied in this investigation. The first series of smelts made to determine proper flux addition were produced in a 4 lb Ajax induction furnace. The charge, consisting of ore with the proper flux addition, was heated in a graphite crucible until fluid, held fluid for a sufficient time period to obtain 1-5 pct FeO content, and poured. Because of the small size of the charge only the final sample of these melts could be examined. In the melts made in the 50 lb arc furnace, however, grab samples taken at 10 min. intervals between time of initial melting and final pouring were available for examination. These samples allowed a much clearer picture of the course of reaction and crystallization. amounts of ferrous oxide and reduced titanium compounds is opaque to transmitted light. Therefore, all petro-graphic studies had to be made on polished slag sections. A representative sample of slag was cut or broken, mounted in a thermosetting plastic, ground flat using 400 grit silicon carbide, the coarse scratches removed with 600 grit silicon carbide and polished on billiard cloth using levigated alumina. Rouge was avoided because of the entrainment of the red particles in pores in the slag, causing a possible confusion with some of the mineral phases. In order to prevent sample projection above the plastic surface red bakelite was used to hold the sample, and backed up with clear lucite. In this manner sample labels could be permanently retained in the mounting. The polished samples were examined on a Bausch and Lomb metallograph at magnifications of 250 X, 500 X, 1000 X and 1800 X. The instrument was equipped for examination of specimens under bright field illumination and with crossed nicols. A magenta tint plate to aid in color tone differentiation was also used. Petrology of Slags In order to determine the composition and mineral relatinos of a previously unreported system petrologically, it is essential that the starting composition, reaction temperature and final composition be known. The chemical composition of the ilmenite ore used in these smelts is given in Table 1, and the complete analysis of a typical high titanium, low iron slag is given in Table 2. In the winning of TiO2 from ilmenite by a smelting process it is necessary to produce a slag which will melt at an economically feasible temperature, remain molten as the iron is removed by reduction, be fluid enough to be readily removed from the furnace, contain a high percentage of TiO2 and a low percentage of reduced titanium com-

Jan 1, 1950

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

GEORGE OTIS SMITH, the Institute's new presi-dent, continues the long tradition of close asso-ciation between the organization and economic geology. Several preceding presidents have been eco-nomic geologists, and a gen-erous share of space in the TRANSACTIONS has always been devoted to that subject, one of critical importance to the miner as well as the seeker for ore. Mr. Smith has long served the Institute, hav-ing been a director since 1921 and first vice-president since 1927. He was born in Hodg-don, Me., on Feb. 22, 1871, and graduated at Colby College, where he took his A.B. and A.M. He did graduate work at Johns Hopkins, where he re-ceived a Ph.D. in 1896. Meanwhile he had engaged in field geological work in Michi-gan, Utah and Washington with the Geological Survey. In 1896 he joined the regular staff of that organization, be-coming director in 1907. He has been with the Survey con-tinuously since he first joined, with the exception of one year when he was furloughed to serve as a member of the U. S. Coal Commission. His special interest for many years has been in the eco-nomic aspects, in the larger sense, of the mineral in-dustry, matters that are necessarily the subject of strong differences of opinion, but which he has dis-cussed with good temper though with full adherence to his strong con-victions.

Jan 3, 1928

By W. A. Krivsky, R. Schuhmann

PREVIOUS papers in this series on the thermo-•t dynamics of copper-smelting systems have presented a survey of the field and an outline of the overall program: thermodynamic studies of iron silicate slags, 2-4 and thermodynamic data for simple mattes in the Cu-S system.5 Since this program was started, an excellent summary of the whole field of physical chemistry of copper smelting was published by Ruddle. The present paper represents a further step in the study of liquid mattes, and deals specifically with the Cu-Fe-S system. The importance of the Cu-Fe-S system to copper smelting is evident from the fact that these three elements constitute 90 to 99 pct of the totalweight of most commercial mattes. In copper mattes oxygen is an important fourth component. Oxygen was rigorously excluded in the work to be described in this paper. However, the behavior of oxygen in mattes was the subject of a companion research by Lander' which will be described in a subsequent publication. Several studies have been made previously of phase equilibria in the Cu-Fe-S system,8-10 so that the ternary phase diagram is fairly well established in most regions. Also, separate studies have been made of the phase diagrams and thermodynamic properties for the three binary systems: CU-S,5,12-15 CU-Fe,11,14,17 and FeS.11,14,16,17 However, no work has

Jan 1, 1958

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

By Herman F. Kaiser, Charles S. Barrett, Robert F. Mehl

The copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process arc available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system' is 779" C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per cent) of silver in solid solution; this solid solubility decreases to zero at room temperature.² Silver at the eutectic temperature rctains 14.0

Jan 1, 1935

By Charles S. Barrett, Herman F. Kaiser, Robert F. Mehl

The copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process arc available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system' is 779" C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per cent) of silver in solid solution; this solid solubility decreases to zero at room temperature.² Silver at the eutectic temperature rctains 14.0

Jan 1, 1935

By G. Howell Clevenger

FORMERLY great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,1 Breuil,2 Wigham,3 Burgess and Aston,4 Ball and Wingham,5 Miiller,6 Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil 9 and Stead.10 Stead 11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness " to the presence of small amounts of copper. Turner 12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 10, 1913