Search Documents

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Since the beginning of the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.' Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally the measurements are made systematically along the whole length of the open hole. The physical factors , or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1934

By John C. Branner

No precise geographic limits can be given for the zinc- and lead-region of North Arkansas. In general terms it lies N. of the Boston mountains and W. of the St. Louis, Iron Mountain and Southern railway; but the prospecting and the development of the ore-deposits have not gone far enough to outline more than vaguely the areas over which workable deposits are to be expected. The tardiness of the development of the region is due in part to its topography, as a hilly and partly mountainous country, through which there have been no railways until recently. There is no longer any doubt, however, about the existence in that region of large bodies of zinc-ores. I. General Geology. The general geology of the region is, in the main, quite simple, but that of the ore-deposits is less so. The zinc-regions of North Arkansas lie about the southern flanks of the Ozark dome. The rocks are approximately horizontal, but have a gentle southward dip away from the axis of this dome. Figs. 1, 2 and 3 show the broad features of the to-. pography and geologic structure. South of the zinc-region, the sandstones and shales of the lower Coal-Measures form the north-facing escarpment of the Boston mountains. Beneath the Coal-Measure rocks are the limestones and cherts of the Lower Carboniferous; and these rest upon Silurian and Ordovician beds. The uppermost beds (Coal-Measures) have been cut into by erosion along the mountain-slopes so that their edges or outcrops have a meandering or dendritic form. The same thing happens with the Lower Carboniferous beds; but these, haying been more or less protected by the overlying Coal-Measured, have broader bases, and cover a much larger area. In places,

Jan 1, 1902

By C. Schlumberger

SINCE the beginning of .the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.1 Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally. the measurements are made syste-matically along the whole length of the open hole. The physical factors or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1932

By Carl Henrich

The Ducktown copper-mines are located in the southeast corner of Tennessee. The name Ducktown was originally given to a district occupying the southeast corner of Polk county, which in turn occupies the southeast corner of the State. Fig. 1 is a map of the vicinity of Ducktown, taken from the topographical surveys of the United States Geological Survey. The Ducktown district is bounded on the east by Cherokee county, North Carolina (the boundary-line between the two States running here a little east of north along the western slope of Pack mountain), and on the west by the eastern foot-hills of Little Frog mountain. On the north, Stansbury mountain, really a chain of low mountains or hills, forms the dividing-line between Ducktown and Turtletown districts. On the south, the Ducktown district extends beyond the Ocoee river to the Georgia State line.. This line, in going west, gradually recedes southwards from that river into the foot-hills of Big Frog mountain, the highest mountain of the neighborhood, which rises about 4300 feet above sea-level, while the surface of the Ocoee river, where it leaves the Ducktown district, is less than 1500 feet above sea-level. It will be seen from this description, and from a study of the map, that the Ducktown district occupies the northern part of a kind of basin, bounded on the east by Pack mountain and on the west by Little and Big Frog mountains. Between these mountains the Ocoee river, draining the basin, cuts its way to the Hiwassee and the Tennessee rivers in a narrow gorge, through the crystalline slates and schists, which from their excellent exposure in this Ocoee gorge have received the local

Jan 1, 1896

By J. L. Byers

THE metals of the platinum group, ruthenium, rhodium, palladium, osmium, iridium and platinum, have certain characteristic effects on the structure and appearance of the cupellation bead. These effects are dependent not only on the particular member of the group present, but also on its concentration. The extent and quality of these effects, however, have not received investigation worthy of their importance. Bannister and Patching investigated the qualitative effects of some of these metals in 1913. This paper deals with a possible rapid qualitative and quantitative delineation of the effects exerted on the cupellation bead by the various metals in the platinum group. More particularly, the paper correlates quantitatively the presence of such metals with their characteristic structural and surface effects. Inasmuch as the various members of the group are more frequently associated with gold than with silver, the gold button will receive the greater consideration. The past two decades have seen a much greater interest manifested in this particular group of metals, because of the increased industrial demand for them. There has been a constantly growing need for assays that will not only express the silver and gold values but also indicate the presence of the other metals. If these indications could be used as quantitative criteria, their value would be greatly increased, because the methods of chemical analysis for the elements of the platinum group are lengthy, involved and unreliable except when the analysis is made by an expert and experienced rare-metal analyst. The materials for the X-ray diffraction examination of the different beads were prepared by filing and screening to -200 mesh, and were then rayed in a General Electric X-ray diffraction unit. The filed samples were treated magnetically in order to eliminate any possible steel particles. Sodium chloride and C.P. gold and silver were used as standard comparators.2 (See Table 1.)

Jan 1, 1932

By Paul Beck

WHILE the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room tem-perature is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains are not noticeably elongated in the first place. However, with small deformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell,1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is com-pleted-after the deformed grains have been replaced by new unde-formed grains-the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. elapsed before the deformed samples were ready for examination, and consequently no recrystallization time shorter than 5 min. could be measured.

Jan 1, 1939

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By A. J. Conelius, D. P. Sobocinski

This paper presents a correlation for predicting the behavior of a water cone as it builds from the static water-oil contact to breakthrough conditions. The correlation is partly empirical and involves dimensionless groups of reservoir and fluid properties and of production and well characteristics. The groups were deduced from the scaling criteria for the immiscible displacement of oil by water. The correlation is based on a limited amount of experimenfal data from a laboratory sand-packed model and on results from a computer program for a two-dimensional, incompressible system. Because the correlating groups are dimensionless, they can be used to estimate the performance of water coning cases not specifically considered in the correlation. However, despite its dimensionless nature, the correlation is not completely general and will not provide meaningful estimates of cone behavior in many situations. INTRODUCTION AND BACKGROUND The production of water from oil wells is a common occurrence which increases the cost of producing operations and may reduce the efficiency of the depletion mechanism and the recovery of reserves. We will deal with one cause of this water production, namely, coning. The coning of water into a producing well is caused by pressure gradients established around the wellbore by the production of fluids from the well. These pressure gradients can raise the water-oil contact near the well where gradients are most severe. Gravity forces that arise from fluid density differences counterbalance the flowing pressure gradients and tend to keep the water out of the oil zone. Therefore, at any given time, there is a balance between gravitational and viscous forces at points on and away from the completion interval. When the dynamic forces at the wellbore exceed gravitational forces, a cone of water will ultimately break into the well to produce water along with the oil. We can expand on this basic visualization of coning by introducing the concepts of stable cone, unstable cone and critical production rate. For instance, if a well is produced at a constant rate and the pressure gradients in the drainage system have become constant, a steady-state condition is reached. If, at this condition, the dynamic forces at the well are less than the gravity forces, then the water or gas cone that has formed will not extend to the well. Moreover, the cone will neither advance nor recede, thus establishing what is known as a stable cone. Conversely, if the pressure in the system is in an unsteady-state condition, then an unstable cone will continue to advance until steady-state conditions prevail. If the flowing pressure drop at the well is suffcient to overcome the gravity forces, the unstable cone will grow and ultimately break into the well. It is important to note that in a realistic sense, stable cones may only be "pseudostable" because the drainage system and pressure distribution generally change. For example, with reservoir depletion, the water-oil contact may advance toward the completion interval, thereby increasing chances for coning. As another example, reduced productivity due to well damage requires a corresponding increase in the flowing pressure drop LO maintain a given production rate. This increase in pressure drop may force an otherwise stable cone into a well. The critical production rate, well known in the literature, is the rate above which the flowing pressure gradient at the well causes water (or gas) to cone into the well. It is, therefore, the maximum rate of oil production without concurrent production of the displacing phase by coning. At the critical rate, a built-up cone is stable but is at a position of incipient breakthrough. Numerous papers have been published on critical rates. Some of the better known of these include the work of (1) Muskat and Wyckoff,' who first dealt with the coning problem; (2) Chaney, et al,' who developed expressions similar to those of Muskat but who presented results in a conven ient-to-use graphical form (the "Sun" method); and (3) Meyer and Garder,b hose analysis is based on radial-flow formulas. One assumption in critical production rate analyses is that the cone has built-up to just before its breakthrough into the well. But, these analyses reveal nothing directly about the time it takes for the cone to build up to this incipient breakthrough position. Thus, water-free oil can be produced from a well for prolonged periods at rates above the critical rate before the well reaches the condition to which the critical rate applies. The published literature contains little on the rate of growth of a cone. Experimentally, Meyer and Searcy studied the rate of rise of a cone in a Hele-Shaw model.' Additional related work on water breakthrough and produced water-oil ratios in water driven reservoirs was reported by Muskat," Hutchinson and Kemp," Henley, et al,' and Stevens, et a1.B Theoretically, the basic coning equations for a water-oil system can be developed by applying the conservation of mass to each of the phases, relating flow velocities with pressure by Darcy's law, and relating pressures across water-oil interfaces by capillary pressure. With the usual boundaries at the well and reservoir limits, the solution of the resulting equations for the time behavior of a water-oil interface constitutes a free-surface, boundary-value problem. The shape of the boundary depends on the internal potential distribution, while this

Jan 1, 1966

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase 'fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,' hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.' It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

By D. Cox, M. J. Duggin, L. Zwell

The carbides of approximate composition and Mn have been studied using X-ray diffraction techniques. Those carbides of the type (Fe,Aln)zC ave isostructural with cementite. The cell pararmeters a and c have minimum values at approximately 10 at. pd substitution of manganese for iron; no satisfactory explanation has yet been found for this phenomenon. The carbide fFeMn4)C has a monoclinic unit cell whose dimensions are close to those of ,11,15Cz A neu-troip-dij~ractiot~ study of (F'eAlrz4)C~ reveals that, like MnsCZ, it is isostructural with Pd5Bz. The iron and manganese atoms occupy the palladium atom sites, while the carbon atoms were found to have the same atomic coordinates as the hovon atoms. A neutrorr-diffraction study of indicates that the carbon-atom positions are very close to those occupied in (Fez.,ll/lr~,.3)C. In both carbides studied, tlre iron and manganese atomzs were found to be essentially randomly distributed, although, in the case of (Fe,.811fn1.2)C, it is possible that there may be a slight preference of manganese atoms for- the general (d) positions and a corresponding slight preference of iron atoms for the special (c) positions. It has been found that a complete range of solid solution exists between Fe3C and Mn3C at 1050°C,I although Mn3C becomes unstable when the temperature is reduced to 95O0C,' and can only be retained by rapid quenching. It is also known that a complete range of solid solution exists from Fe5Cz to M~SC~,~ although the stability range of carbides of the type (Fe,Mn)sCz as a function of the relative proportions of iron and manganese is not known. X-ray examinations of Oh-man's carbide3 and Spiegeleisenkristall,~ which have the approximate compositions (Fe3.67Mnl.33)C2 and (Fe3-,Mn,)C, where x lies between 0.4 and 1, respectively, have been made. The following carbides have also been studied: ] The lattice parameters determined during these investigations are listed in Table I. It is seen that carbides of the type (Fe,Mn)sCz have a monoclinic unit cell while carbides of the type (Fe,Mn)3C have an orthorhombic unit cell. It is evident that the variation of lattice parameters with manganese content is not linear for carbides of the type (Fe,Mn)3C. The coordinates of the atoms in (Fe2.7Mno.3)C have recently been determined by single-crystal analysis., The fractional atomic coordinates have been shown by Fasiska and jeffrey to be in good agreement withj those deduced from an earlier analysis of Fe3C by Lipson and etch.' However, it was impossible to determine whether iron and manganese atoms occupied ordered positions because of the small difference between the atomic scattering factors of iron and manganese. The atomic positions in Mn5Cz (Refs. 8 and 9) and Fe5C2 (Refs. 7 and 8) have been obtained only by comparisons made with the isostructural compounds P~SB~.' Since X-ray diffraction techniques were used in these investigations, accurate positioning of the carbon atoms, which have a low atomic scattering factor, was difficult. No attempt has been made to determine the atomic positions in the other carbides previously studied. It was felt that an investigation of the lattice parameters of a number of intermediate carbides of the types (Fe,Mn)sCZ and (Fe,Mn)& would be of interest. It seemed likely that a neutron-diffract ion study of such carbides would indicate whether ordering occurred between the iron and manganese atoms because of the large difference between the neutron-scattering cross sections of iron and manganese. It also seemed probable that such an investigation would provide a determination of the atomic coordinates of the carbon atoms. I) EXPERIMENTAL DETAILS Specimens, each weighing approximately 20 g, were carefully prepared according to the following proportions: The components were 500-mesh powders of 99.995 pct purity iron and spectroscopically pure carbon and a 200-mesh powder of 99.995 pct purity manganese. The component powders were intimately mixed by prolonged shaking, then each specimen was inserted into a spot-welded cylindrical container of tantalum foil, whose end was closed but not sealed. Each specimen in its envelope was then sintered at 1050° C for 24 hr in a thin-walled evacuated quartz capsule, such a time having been previously found sufficient for equilibrium to be attained.' Each specimen was then quenched in order to attempt to retain the high-temperature phase, as the literature indicates that transformations may occur on cooling. Debye-Scherrer X-ray photographs were taken of each specimen using a 114.6-mm-diam camera, Fig. 1, patterns 2 to 6. The exposure time was 6 hr using filtered iron radiation at a tube voltage of 40 kv and a tube current of 12 ma.

Jan 1, 1967

By G. A. Zeito

Detailed visua1 examination of outcrops was used to ob-tain data on the lateral extent of shale breaks. Thirty vertical exposures belonging to maritie, deltaic and channel depositiorral environrrrents were exatmind, surveyed and photographed. The dimensions of the outcrops ranged from 356- to 8,240-ft long and 25- to 265-ft thick. Shale breaks were found to extend laterally for significant distances. and in some sands terminates by joining other break v much more frequently than by disappearance. Consequently with regard to flaw, a gross sand consisted of both continuous and discontinuous subunits. The degree of continuity of shale breaks as well as the occurrence and spatial distribution of discontinuities were different for the three depositional environments. Statistical eva1uations were performed to determine the confidence level with which estimates derived from outcrops can be applied to reservoir sands. Results of these evaluations revealed that: (I) the lateral continuity of shale breaks in marine. sands is si~nificatit, and the estimates of lateral extent can he applied to reservoir sands with a high degree of confidence (80 to 99 per cent of the shale breaks continued more than 500 ft, with a confidence of 86 per cent); and (2) the tendency for adjacent shale breaks to converge upon each other over small distances in deltaic and channel sands is highly significant (62 to 70 per cent of the shale breaks converged in less than 250 ft, with a confidence of 50 per cent), hut the probable magnitude of the resulting sand discontinuities cannot yet he predicted with adequate confidence. INTRODUCTION Almost all of the efforts devoted to characterization of the variable nature of reservoir sands have been focussed on permeability variations. Among the widely used concepts that have emerged from these efforts are those of stratified permeabilities, random permeabilities, and communicating and noncommunicating layers of different permeabilities. This study is concerned with the presence of interbedded shales and silt laminations. These features are impermeable or only slightly permeable to flow. Therefore, knowledge of the extent to which they continue laterally and the manner in which they terminate within the bodies of gross sands is important for proper description of reservoir flow. Initial field observations made on outcrops revealed that shale breaks and the relatively thinner silt laminae have impressive lateral continuity. They appeared to divide sand sections into separate individual sand layers. Although most of the layers were continuous across the total lengths of the outcrops, some were discontinuous because the- bounding shale breaks converged. Furthermore, the discontinuous layers appeared more prevalent in channel and deltaic sands than in marine sands. Based on these initial findings, a detailed investigation was carried out to determine, quantitatively: (1) the degree of continuity of shale breaks in marine. deltaic and channel sands; and (2) the frequency and spatial distribution of discontinuities in the three environments. PROCEDURE The procedure used to obtain field data from outcrops included visual examination, surveying and photographing each outcrop. The photographs were examined carefully and important outcrop features were traced, measured and recorded. The selection of outcrops for this study was made on the basis that each outcrop should be exposed clearly to permit detailed visual examination of vertical lithology. and it should also be sufficiently long (over 200 ft) to provide useful data on the lateral continuity of lithology. Identification of the depositional environment for each outcrop was made on the basis of bedding characteristics, vertical sequence of lithology and the presence of indicative sedimentary features. Whenever possible, hand specimens of associated shales were collected to determine depositional origin. Almost one-half of the outcrops used in this study required environmental identification; the remainder had already been identified by previous investigators. Several photographs of each outcrop were usually required to cover the entire length of the outcrop. These photographs were taken from one station or several, depending on the terrain, size of the outcrop and distance to the outcrop. A Hasselblad camera, with a standard 80-mm lens and a 250-mm telephoto lens, was used. The telephoto lens permitted photographing outcrops as far as two miles away. Slow-speed films were used. either Panatomic-X or Plus-X. The final operation conducted in the field was that of surveying the outcrops. The distance of an outcrop from a point of observation was determined by a triangulation method using the plane table. The measured distance was then combined with the angle of view of the camera lens to establish a scale to be used on the photographs. Films were processed using standard processing techniques and 4.5X enlargements made. The enlargements of each outcrop were butted together to form a single panorama. Slides were also prepared on several outcrops; these were used whenever greater magnification (wall projection) was required to bring out maximum lithologic detail. The shale breaks and bedding planes in each outcrop were traced on transparent acetate film superimposed on

Jan 1, 1966

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By K. A. Semlak, F. N. Rhines

NFILTRATION is a term used to designate that i- process by which the pores of a metal powder are filled with a relatively low-melting liquid metal through the action of capillary forces. This is accomplished in practice either by heating the porous body in contact with the solid infiltrant metal above the melting point of the latter, or by preheating the porous body separately and then dipping it into the liquid metal. The liquid, as it sweeps through the porous body, replaces the gases progressively, thus yielding a relatively dense product in a short time.' Liquid-phase sintering, which is related to infiltration, is a process by which a mixture of two or more metal powders is sintered at a temperature between the liquidus and solidus of the ultimate alloy.' According to Cannon" liquid-phase sintering can be divided into three stages which he calls liquid flow, accommodation, and solid sintering. The largest density increase occurs during the first stage, where the lower melting component melts and, driven by capillary forces, flows among the particles of the higher melting component, where, after dissolution of the bonds between the solid particles, it moves them into close packing. This happens so quickly that little has yet been learned of its mechanism. A study of the rate of capillary rise of a liquid metal in a higher melting metal-powder compact may be expected, therefore, to contribute not only to a firmer understanding of the process of infiltration as such but also to a more extensive knowledge of what occurs during the initial stage of liquid-phase sintering. Theoretical Basis In order to derive a mathematical expression of the rate of infiltration, it has been assumed that a powder compact consists of a great many parallel capillary tubes and that the rate of rise of a liquid in an average capillary channel represents the rise in the entire compact. For a straight capillary, assuming that Poiseuille's law obtains for the non-stationary state and that wetting is very rapid, Ligenza and Bernstein' have derived the following differential eauation of motion where h is the height of rise of the column of liquid at time t, R, is the radius and 1 the length of the capillary, t) and 7, the viscosities of liquid and air, respectively, p and p, the density of the liquid and air, respectively, y the liquid-gas surface tension, 0 the liquid-solid contact angle, and g the acceleration due to gravity. The term on the left of Equation [I] represents the rate of change of momentum of the contents of the capillary tube. On the right the terms represent, respectively, the forces due to a) surface tension, b) viscous resistance, c) gravity, and d) end-drag effect. Equation [I] is not amenable to explicit solution, but for a tube of sufficiently small radius, the rate of rise may be slow enough so that the rate of change of momentum and end-drag terms may be neglected. The validity of this simplification was established by Ligenza and Bernstein' by graphical differentiation of observed data obtained from organic liquids rising in glass tubes. The solution of this simplified case is:

Jan 1, 1959

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress' four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver's new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers' courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952

By Edward F. Winter, C. E. Ruoff

A silicon solid-state array image scanner is described. This paper deals with structural and performance properties of the array which basically consists of PIN photo and gating diodes, and low capacitance isolation diodes. Each chip of the array is composed of an 8 by 9 matrix of photo detector cells; each cell contains one each of the three diode types mentioned. This x-y matrix is read a column at a time with an access delay of approximately 100 nsec per column. It is designed to detect the presence or absence of illumination within 10-mil diam image spots located on a 15- by 15-mil grid. Radiant power level of an illuminated spot is low; of interest is the range around I uw with a of 8400g Structural improvements to the original array which will result THE purpose of this paper is to describe the results of a solid state scanner exploratory development activity. The scanner is intended to sense the presence or absence of low-level illumination falling upon a matrix of 10-mil wide squares arranged on a 15- by 15-mil x-y grid pattern. The light of interest has a wavelength of 8400, characteristic of radiation emitted from a GaAs lasing diode. This wavelength matches well the spectral absorption of silicon,' thus the well-developed silicon processing technology can be applied to fabricating large integrated arrays of PIN photocells to sense the radiation. The illumination state of the cells of the array is read, one column at a time, by addressing a drive line of the particular column in question and examining the state of those sense lines which are orthogonal to the drive Lines of in greater sensitivity at various wavelengths, both above and below 8400Å, and in greater speed are presented. These include variations in diffusion depth, resistivity of N and P regions, isolation techniques, and packaging. Trade-offs between access speed, cycle frequency, and sensitivity are discussed. A packaging approach to achieving an array composed of several chips is described. Requirements on this package are: 1) maintenance of 15- by 15-mil pitch of the light sensitive cell position, therefore positional accuracy of mounted 8 by 9 cell photo detector chips; 2) maintenance of inherent high array speed even though signal levels are low through high density close proximity mounting of monolithic sense amplifier circuitry. the array. One bank of N sense amplifiers is required, where N is the number of photodiode cells in each column of the array. CELL AND CHI" STRUCTURE A photograph of a single monolithic cell is shown in Fig. 1. Each cell is composed of three junctions, an isolation junction, a logic or blocking diode junction, and a photodiode junction; all of these junctions are connected electrically by a common N region. An electrical schematic of four cells of the array is shown in Fig. 2 with the associated driver and sense amplifier circuits in block diagram form. Note the common cathode configuration of the three diodes of each cell. Fig. 3, a diagram of the cell vertical struc ture, illustrates how the electrical configuration of

Jan 1, 1970

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By G. W. P. Rengstorff, L. E. Olds

High purity molybdenum ingots containing controlled amounts of a single impurity element (oxygen, nitrogen, or carbon) were prepared. These ingots were tested for ductility by bending test specimens at various temperatures. The relationship between the plastic behavior of the ingots and their chemical composition has been determined. MANY proposed applications for molybdenum require ductility at or near room temperature. At the present time, it is possible to obtain wrought molybdenum with considerable ductility only if special fabrication techniques are used to control the grain structure. Starting with are-cast or powder metallurgy ingots, the usual methods for obtaining ductility rely on fabrication procedures that result in fibered microstructures in the finished product. Recently, it has been found that the ductility of either powder metallurgy or are-cast molybdenum can be improved by uniform recrystallization of the metal to a very fine equiaxed grain structure.' The need for a fibered or a fine grained structure may limit the practical usefulness of molybdenum. For example, welding. which may be used in fabricating the metal, generally produces coarse grained structures that lead to brittleness. This applies, certainly, to currently available commercial molybdenum. Although commercial molybdenum is brittle when the grains are coarse, it has been shown experimentally that fine grained structures are not always essential for ductility. For instance, as-cast molybdenum with a coarse columnar grain structure is ductile if it is sufficiently pure.' Because high purity cast molybdenum has good ductility even when coarse grained, it is probable that the brittleness in coarse grained commercial molybdenum is caused by the impurity content of the metal. Although the general effects of impurities on the cold ductility of molybdenum have been known in a qualitative manner for some time, no quantitative evaluation of these effects has been available. The present investigation was made in order to determine more accurately the effects of oxygen, nitrogen, and carbon on the cold ductility of cast molybdenum. Oxygen has long been known to be detrimental to ductility, although the minimum amount which will embrittle molybdenum has been open to speculation. Parke and Ham" showed that ingots with oxygen contents above 0.003 pct could not be forged. Maringer and Schwope have described the embrittle-ment of molybdenum wire by oxygen. A discussion on the effects of heat treatment on the distribution of oxygen in molybdenum has been given by Perry, Spacil, and Wulff." Although nitrogen would also be expected to have harmful effects on ductility, no extensive work has been done previously to determine whether this is so. However, Tury and Krausz" found that wires presumably with less than 0.007 pct N were brittle. Carbon is added to commercial cast molybdenum for deoxidation. Parke and Ham" have shown that molybdenum containing as much as 0.06 pct C could be forged if the oxygen was kept below 0.003 pct. Also, Bruckart and others' found that the room temperature ductility of sintered molybdenum improved with carbon contents up to 0.84 pct. However, Rengstorff and Fischer' found that residual carbide particles in cast molybdenum apparently had an unfavorable effect on room temperature ductility.

Jan 1, 1957

By R. Gibson, F. S. Turneaure

The tin deposit of Monserrat, Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals. THE Monserrat mine1'2 of the Compania Minera Monserrat is located 11 km east of Callipampa, a station on the Antofagasta and Bolivia Railway some 55 km south of Oruro. The mine lies in a group of low hills on the east slope of a broad valley of northerly trend. The valley is separated from the altiplano to the west by a prominent ridge that rises several hundred meters above the surrounding country (fig. 1). Callipampa is situated a short distance west of the ridge, near the east margin of the altiplano. The elevation at Callipampa is 3700 m and at the mine 4100 m. Monserrat is near the northeast limit of what may be called the Poopo-Pazna district, an area of northwesterly trend about 25 km in length and 15 km in width. The district includes the tin-silver prospects of Poopo to the north, the zinc-tin deposits of Salvador to the southwest, and the tin-tourmaline veins of Avicaya to the south. Along the prominent ridge already mentioned, which forms the western limit of the district, there are several tin and antimony prospects including the Trinacria mine, which is famous for its fine specimens of cylindrite. Although the principal ore mineral is cassiterite, the tin deposit of Monserrat contains an unusual amount of teallite. Cassiterite occurs in part as a finely granular mixture with sulphides of iron and zinc and in part as needle tin of late hypogene age. The regional structure is dominated by broad folds typical of the Andes of Central Bolivia and similar to those of the Llallagua district. The area adjacent to the Monserrat mine is underlain by thin-bedded shale somewhat variable in color but predominantly dark grey to black. The beds strike northwest and dip at low angles southwest, forming part of the northeast limb of a major syncline. A resistant sandstone formation, which underlies the black shale, crops out along a ridge east of the mine and also accounts for the high ridge to the west that was previously mentioned. No igneous rock of any kind is found at Monserrat. The nearest intrusive bodies known are the irregular dikes and masses of quartz porphyry at Avicaya about 10 km to the south. Mine Workings The Monserrat property includes one main vein, which can be followed on the surface for 1600 m, and two or three branch veins of distinctly minor importance. The principal haulage tunnel, referred to as the San Carlos adit or level III, extends northeasterly for 1700 m, following the main vein throughout most of this distance. Above the adit, there are

Jan 1, 1951