Search Documents

By N. A. Gokeen, M. Ohtani

EFFECT of elements on the solubility of carbon in liquid iron is useful in calculating and correlating a number of thermodynamic properties as shown elsewhere in detail.' Kitchener, Bockris, and spratt2, and later Turkdogan and Hancock3 have investigated the effect of sulfur on the solubility of carbon at various temperatures and concentrations. For any chosen sulfur concentration, the solubility of carbon reported by Kitchener et al. is considerably lower than that by Turkdogan and Hancock. It was therefore felt that a reinvestigation of this problem was necessary. EXPERIMENTAL METHOD An alloy of Fe-C-S .was prepared with electrolytic iron and ferrous sulfide melted by induction in a graphite crucible, 4 in. high 1 1/2 in. ID under a CO-atmosphere. The temperature, held at 1500" ± 5°C in all experiments, was measured with a Pt-Pt + 10 pct Rh thermocouple immersed into the melt. In order to assure saturation with carbon, the melt was stirred with a graphite rod. After approximately 1 hr at 1500 °C, a sample was obtained by sucking the melt into a silica tube, 4 mm ID. The sample was then analyzed for carbon and sulfur by usual methods. RESULTS The results are presented in Table I and plotted in Fig. 1 with the individual values of Turkdogan and Hancock.3 Scattering in the data is equivalent to 3 pct or less in carbon analysis. The broken line represents the empirical equation obtained by Kitchener et al. from their data. It is evident that the present data are in good agreement with those of the former investigators but in disagreement with the latter. The cause for this discrepancy cannot be readily offered since the experimental methods in the three investigations were nearly identical. Additional evidence corroborating the author's results may be presented in the following manner. The difference between the solubilities of carbon in the ternary Fe-C-X melt with a small concentration of any element X, and in the binary Fe-C melt is %?C = %CIII-%CII [1] where %?C is the change in solubility, and %CIII and %CII are the solubilities in the ternary and the binary systems respectively. The value of %Cii

Jan 1, 1961

Robert Schorr, San Francisco, Cal. (communication to the Secretary*):—In operatioils requiring the expenditure of fuel, it is solely a question of supplying a certain number of heat-units at certain temperature-conditions. The difficulty of controlling these temperature-conditions is mainly responsible for low efficiency, unless utilizable waste heat is carefully applied either for the pre-heating of the air necessary for combustion, or for the heating of the raw materials, or in other departments of the works to generate steam, etc. A high theoretical or thermal efficiency very often does not establish a high " commercial" efficieiicy, and this fact is responsible for apparent crude practice in many arts. Coal is still very cheap in the East, and oil sells in the West for less than anywhere else in the world. Despite these favorable conditions, I believe that the list of references given in E. C. Eckel's book,' and also the contributions of C. Naske,2 will show that Mr. Eldred's statement, that a the study of the phenomena of applied combustion has been neglected," is not justified as far as the burning of cement is concerned. I have investigated the heat-balance of a lirne-kiln ailci the commercial advantage of using generator-gas for calcination. Mr. Eldred proposes to calcine the materials in the present type of rotary kiln, gas-fired with long-flame combustion, and to Pdke the fritted calcines to a special, gas-fired clinkering-kiln, which shall embody heat-regenerators. While his state-

Jan 1, 1911

By Martin J. Gungl, J. Lyman MacInnis

None of the industry submissions could persuade the Canadian Tax Reform draftsmen that the rate of return has had as much bearing on investors' decisions to invest in Canada as the success records of Canadian ore findings. The goverment opted for the position that mining capital goes where the ore can be found. Many tax incentives which were available until the end of 1971 have been greatly reduced. However, it is still recognized that new ventures in exploration and development of natural resources deserve a break even if there is reduced recognition of the established and highly successful members of the industry unless they continue to search and develop. The latter will also get some breaks for processing beyond the prime metal stage.

Jan 7, 1972

By Richard E. McElvain, I. Cave

The selection of centrifugal pumps for mill discharge duty should be based on the total circuit concept. The practice of operating the mill circuit based on limitation of the pump can result in losses in one day which would offset the pump cost. Operating data from 25 grinding circuits have been reviewed and comparative results on added mill capacity have established advantages far beyond the less significant maintenance costs with increased circulating load and better cyclone operation. Mill discharge pumps should be selected on the following basis: i) Best available design for wear performance ii) Size to provide best economic life iii) Liner material best suited to circuit conditions Pump efficiency is a secondary consideration because power consumed by pumps is small compared to mill power input. Energy dissipated in mill pumps is contributing to comminution of ore.

Jan 1, 1982

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel framework buildings started toward the end of the last century. Progressively the requirements became more stringent, crushed bank slag, weighing 80 lb per cu ft as compared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft. Geology Perlite is one of the large family of rocks originating from a granitic or acidic magma and generally has a "rhyolitic composition with a marked perlitic structure."² The name "perlite" is a derivation from "perlstein" originally given "to certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."3 The cause of the perlitic texture is somewhat controversial. Johannsen attributes the texture to strain set up in the glass by cooling and describes the finding of peculiar, glassy balls, called marekanite, more or less rounded and showing concave indentations, which may be left when perlite is broken. Frank Rutley, on the other hand, in 1881, while working on vitreous rocks from Montana, observed that there was incipient or partially started crystallization with segregation of water toward the un-crystallized portion in all specimens of perlite examined. Further he observed evidence of strain around focii of crystallization to which he ascribed the development of the spherical cracking which gives the rock its perlitic texture.4 Widespread over the western and southwestern United States where Tertiary vulcanism is exposed, perlite commonly is associated with andesitic, basaltic, and rhyolitic lavas with inter-bedded tuffs and ash of Eocene age although some deposits are associated with rocks assigned to the Pliocene age.5, 6 n nearly all cases the perlite overlies water laid tuff beds or agglomerates or breccias of explosive nature, an outstanding exception being the occurrence of perlite as the chilled selvage of andesite intrusions.7'8 Available chemical analyses of per-lites from the western and southwestern United States indicate that they are varieties of leucorhyolites rather than of normal rhyolites, leucorhyolites having less than 5 pct of dark minerals, normal rhyolites having more than 5 pct. This conforms with Johannsen's observation that leucorhyolites are the prevailing kind in North America.9 Tables 1 and 2 give

Jan 1, 1950

By Philip B. Dettmer

In the last two decades we have witnessed many new developments in the art and science of mineral beneficiation. Competition and the pressures of inflation have caused operating managements to search for every possible way to squeeze out a few more cents savings per ton of product. One illustration of this is the trend toward the use of larger grinding mills. A few years ago a 1000 hp ball mill was considered a giant. Now we have many examples of successful grinding mill installations of 3000 to 4400 hp connected load per mill. The trend toward these larger mills is increasing every year, and we have not seen the upper limit yet. For example, three 6600 hp cement finish mills are presently being built for a plant in Missouri.

Jan 4, 1965

By A. Keil

TO measure the absolute conductivity of metallic specimens it is generally necessary to have exact geometrical shapes and good electrical contact with the test-piece. To overcome limitations of the standard methods, an electronic conductivity-meter* Trade name, Sigmatest; model Dr. F. Forster; Reutlingen, Ger-many. has been developed, which works on the principle of inducing high frequency eddy-currents in the specimens and measuring the reaction of these curients on a measuring coil.',' To attach the instrument to the test specimen, a flat area of about 10 mm diam is all that is necessary. The reading is taken off a scale calibrated in pet of International Annealed Copper Standard. The induced eddy-currents are propagated in a circular motion parallel to the surface. Thickness of the layer included in a measurement depends on the frequency used. With a frequency of 60 kc per sec, the penetration of the currents was 0.8 mm at the upper limit of the scale, and 2 mm at the lower limit. The method is limited to nonferrous metals and other applications have been described elsewhere." The object of the present investigation was to detect the formation and growth of surface layers of differing conductivity, and to determine the depth to which these changes could be observed. A well known phenomenon which illustrates the problem is the internal oxidation of certain silver alloys containing base metal solutes, such as copper or cadmium, when they are annealed in an oxidizing atmosphere.4, 5 Until now, the only methods available for following these phenomenon have been metallo-graphic examination and hardness tests.0, 7 Changes in mechanical properties of copper alloys by internal oxidation were recently discussed in a more general way by Martin and Smith." When measuring these conductivity changes it must be remembered that the only absolute values of conductivity are those of 1) the nontreated homogeneous specimen, and 2) the final values obtained with a surface layer of depth comparable to the penetration of the eddy-currents. All intermediate values refer to the mixed conductivities of the transformed surface layer and the untransformed alloy, and are thus readings of relative value only. Experimental Results Specimens were annealed for 1/2 hr at 800°C in hydrogen, and the internal oxidation was carried out by thermal treatment in air at 800°C. Fig. 1 shows the results of the first series of experiments. With internal oxidation of a solid solution of 8 pet Cd in silver, the conductivity rises continuously until the surface layer formed has become thick enough to be the deciding factor (about 400µ). Precipitates of CdO are mainly in the form of points, Fig. 2, and, as a result, the electric contact between the silver crystals is not distorted by them. Brine11 tests were run with a 1.25 mm ball and a 7.812 kg load. The specimen annealed in hydrogen and oxidized to a depth of 400µ had a hardness of 40 Bhn,

Jan 1, 1959

Those familiar with the war in France at first hand know that in these last two years the weight of the suffering has fallen upon the families of the well-to-do classes; those who before the war lived in comparative ease and comfort, with every prospect of educating their children as their parents and grandparents had been. Thousands of the men in these families have been killed, "officiers d'élite," and the small pensions accorded the widows permit them only to house and feed their children HELÈNE JOURNÈS. and give them a common-school education. The pension for a lieutenant's widow is $245 a year; for 'a captain's, $345; for a colonel's $575; and so on. At present, it requires three francs a day to provide food for one person in cities, and conditions are not improving. The American Ouvroir Funds, 681 Fifth Ave., New York City, has tried for nearly two years to have individual Americans give individual children a "bourse," or purse, as it is called, of from $150 to $250 a year, so that they may enter such educational institutions as the Lycées, the Polytechnique, Beaux Arts, St. Cyr, etc. The war relief societies of these military schools furnish photographs and histories of children under their care and on their lists.

Jan 12, 1918

By Colin M. Sargent

THE electron diffraction pattern as seen in the electron microscope represents an approximately plane section of the reciprocal lattice. Identifying the zone axis of a diffraction pattern is often laborious for a crystal of low symmetry, especially if several crystal orientations are present. A program has been written in FORTRAN II (Version 2) for the IBM 1620 which will assist in plotting out reciprocal lattice sections. The calculation is performed by choosing a zone axis [uvw] and determining the d spacings and angle between the planes (Ow - v) and (wO - u). (This procedure is varied slightly for zone axes with Miller indices equal to zero.) Cartesian coordinates for the reciprocal lattice points are then calculated for these planes and for (ww— [u + v]). Any reciprocal lattice points within the parallelogram formed by the origin and these three points are then computed. The input and output are best described by use of an example (Monoclinic ZrO2) used in the author's work. Input consists of two cards: 1) The crystal parameters: a, b, c, a, 8, y, e.g., 5.1477, 5.2030, 5.3156, 90.000, 99.380, 90.000. 2) Three numbers, D, E, F, e.g., 5, 3, 3.0710-the first is the limit of the sum (u + v + w) considered; the second limits the absolute value of u, v, and w to (E- 1), e.g., 2, so that zones (221) would be the highest order considered in this example; the third, F, is the required constant, yL. Output is in the format shown in Table I. The reciprocal lattice sections may then be plotted on standard graph paper and compared with the unknown diffraction pattern. (Note that no attempt has been made to deal with systematically absent reflections.) A card deck for the program is available from Colin M. Sargent, ARZ, W-PAFB, Dayton, Ohio, 45433.

Jan 1, 1969

By Thomas R. Smith

This paper covers oil shale resources in those countries that border the Pacific Rim. The major known resources around the Pacific Rim occur in the Western United States, Australia, the People's Republic of China, (PRC) and the Thailand/Burma region. The location of these deposits is shown in Figure 1. In 1965, the U.S. Geological Survey estimated world oil shale deposits of over 4 quadrillion tons having a potential oil yield of over 2 quadrillion barrels. If all this were extracted, it could meet the world's entire energy needs far into the future. However, the Survey also estimated the spent shale waste could cover all of the surface of the world to a depth of about 10 feet. Thus, for this and many other technical and economic reasons, it does not appear to be feasible to develop a large portion of the world's oil shale resources in this century; nor will shale in itself solve our energy problems. Nevertheless, shale oil and other ' synthetic fuels are expected to play an important role in new energy supplies in the longer term. WHAT IS OIL SHALE OR SHALE OIL? The term "oil shale" is sometimes a misnomer, in that the rock is often more of a limestone or siltstone than a shale. The common link between resources termed “oil shale" is that they all contain an insoluble substance cal led kerogen (which is from the Greek words for waxmaking). Kerogen is a form of organic carbon derived from a variety of plants ranging from algae to higher plants. When heated sufficiently, the kerogen generates hydrocarbons called shale oil, a form of synthetic crude oil that in most cases is lower in hydrogen content than conventional crude oil. The amount of oil in oil shale is relatively small --roughly 10 percent (by weight) in the richer shales. To upgrade this synthetic oil to usable products, additional processing is necessary. This brief sketch gives an idea of what this different, but significant, form of hydrocarbon is like. ENVIRONMENTS OF DEPOSITION Most oil shale deposits fall into three environments of sediment deposition: 1ake (called lacustrine), sea (marine) and river (fluvial-deltaic). In each case, the deposition of oil shales took place in quiet water environments where plant life, particularly algal plants, could flourish and, after dying, be deposited in unoxygenated water where the kerogen precursors would be safe from destruction by oxidation. The oil shales that were deposited in large lake basins (lacustrine) have attracted the most attention for development over the years. They often have multiple seams, deposited in a cyclic nature with extensive areal distribution and rapid vertical changes in kerogen content. Grades are moderate to high, ranging from 80 to 200 liters per tonne. Rundle in Australia and the Piceance Creek Basin in Colorado are examples of this type. Both deposits represent large volumes of oil shale in small areas which could provide the large volume of feedstock needed for future commercial operations. The stratigraphic sections of these two deposits feature thick oil shale seams with average grades of 80 - 125 liters/tonne conducive to both open pit, and underground operations. However, the rock strength of the Rundle shale is not sufficient to - support underground mining. On the other hand, the Colorado deposits, being more carbonate in nature, are sufficiently strong to support either type of mining depending on the overburden to ore ratio. These latter types of deposits will likely provide the first target for development of a commercial industry. The marine type is characterized by extensive areal distribution with relatively thin seams. The grades are generally low to moderate, ranging from 50 to 120 liters per tonne. The marine oil shales are common worldwide, and their attractiveness for mining is dependent on the overburden to ore ratio. Because of their widespread areal distribution, their in situ resources can be quite large. The Toolebuc Formation in Central , Queensland, Australia is a good example of this type of deposit being 7-10 meters thick over an extensive area. The Julia Creek deposit with its favorable overburden-to-ore ratio is being studied for possible development. In a fluvial-deltaic environment, there are many small lakes or bogs associated with rivers in which a very pure type of oil shale called torbanite could form. Torbanites are very high grade containing up to 75 percent hydrocarbons. The known occurrences are generally small lenticular deposits associated with coal seams. Even with the high grades, it is not likely that any of the known deposits would warrant commercial development because of their small size. The torbanite deposits in New South Wales, Australia were processed prior to World War I1 near the town of Glen Davis. However, today's known resources of this type are not large enough to warrant a commercial plant.

Jan 1, 1982

By W. H. Schacht

The operations of the Copper Range Co. are located in the Michigan copper district at the southern end of the Keweenaw Peninsula, 8 miles southwest of Hough ton (the center of the district). All the producing mines are situated in a long narrow zone paralleling the peninsula and occupying the central portion. This zone is about 25 miles long and 3 to 4 miles wide. The important mines, in their order from northeast to southwest, are, Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet & Hecla, Osceola, Franklin, Quincy, Isle Royale, Baltic, Trimountain, and Champion; the last three are operated by the Copper Range Co. The existence of copper deposits in this district became known soon after the discovery of America. Many references by early explorers show that copper was found in the possession of many of the American Indians that inhabited the Great Lakes region. There is abundant evidence that exploration of these copper deposits extended into prehistoric times; and some indication that the American Indians carried on operations shortly before the advent of white men. An account of the finding of primitive mining appears in the Government publications of 1850-51 by Foster and Whitney. Although earlier expeditions by white men had been made to the Keweenaw peninsula, an attempt to commercialize the district was not made until after 1765, when Alex. Henry, a British subject, searched the shores of Lake Superior for mineral treasure. His first expedition took him to the Ontonagon River, where he found the famous mass of copper now on exhibition at Washington. In 1771, he started operations along this river with a crew financed by English capital; but after much difficulty and only meager success he found only detached masses while in search for a major deposit. There is no record of any cxploration from 1774 to 1820. In 1838, Dr. Douglas Houghton was appointed state geologist. Prior to that time he had made several visits to this region; and was the first white man to find

Jan 1, 1925

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection function, and a cost function. The three functions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field day available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 1, 1984

By George Burgess

1. Introduction.-THE methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel Co., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.-Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,' as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made.

Jan 2, 1915

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 12, 1979

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1980

By Joel J. Lloyd

The storage and retrieval of geological information is represented by a "Babel" of systems. If the energy and expense that is being expended is to be fully exploited by the earth science community, a common language and common practise is required. Interfacing, applicable in the crossover of scientific disciplines and of polyglot data collections, is neither practical nor economic in the handling of English language information. Whether a single input/output center or a locus of interlocking subcenters is established, is irrelevant. The capture of fugitive information and recapture of lost data is paramount. Existing national committees and international commissions are cognizant of the problem and are engaged with it. The time required to reach agreement may merely complicate the problem. It may prove necessary for a group of individuals to face up to the situation and take the indicated action -- facing the criticism that will probably fall on their heads. The cost of rectifying immediate mistakes may be far less than the delayed execution of a long studied plan. System designs are considered in terms of input elements and output products, various mechanical operating modes are presented, and the economics of organization and maintenance are discussed.

Jan 1, 1969

By C. B. Manula, R. Venkataramani, T. V. Falkie

A linear programming model has been developed to solve a production planning problem for a multi-plant stone operation serving several customers. The factors considered are production capacities, inventory restrictions, demand requirements, and available stone reserves. The objective function to be optimized is the total annual net returns from the quarry operations. For the purposes of model testing, annual stone sales from each plant were divided monthwise, productwise, and assigned to a market. The concept of assigning demands to market sectors and not to any particular plant creates the self-correcting interplay between the plants and the markets. Along with the inventory restrictions, and ending inventory requirements, this interaction enables the model to minimize the external diseconomics. The model was tested against an operating prototype and a number of alternative problems were also considered. Finally, the basic linear programming model has been enlarged by the addition of another dimension and the problem has been derived in a decomposition format.

Jan 1, 1972