Search Documents

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.' The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.' The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00' were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-'. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By R. W. Fountain, J. Chipman

THE solubility of nitrogen in iron and steel has been of considerable interest due to the role of nitrogen in strain-aging and in quench-aging. It is generally considered that quench-aging is the result of precipitation of carbide and nitride particles from supersaturated solid solution, while strain-aging results from the segregation of carbon and nitrogen atoms to dislocations.1-9 The rate of strain-aging is controlled primarily by the amount of carbon and nitrogen in solution and the temperature. In experiments on strain-aging of pure iron with only carbon or nitrogen as impurities, Fast" has shown that even after 40 hr at 50°C carbon did not give any strain-aging while

Jan 1, 1959

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By Herbert Hoover

DURING the year, the' Institute has made the most remarkable growth in its history. Our actual increase in membership was 1816 and therefore was 80 per cent. larger than any previous year. Even without expectation of any abnormal growth, we should pass in the year 1921 the 10;000 mark. The causes of this increased growth are not far to seek.. They lie in the widening vision of the Institute's work, not only in its relation to' the profession but as an avenue of service to the nation as a whole. The Institute is today in the first rank of influence among public institutions in the country. During this year we have, for the first time in many years, had a ?deficit of some $3000 in our finances. The sum is not important, but it- does indicate the tendency of the times, and that is the high cost of living:' The increase in our expenses lay, to the largest degree, on the publishing side of the Institute's work. If we compare the year 1918, as a fairly repre¬sentative year, with that of 1920, we find that the costs of issuing the' Institute's publications, after deducting the income received from these publications, shows a .net increase of about $33,000. for the year. This has been to some degree due to the enlarged membership but to a large degree due to the cost of the paper and printing.

Jan 1, 1921

By Bruce H. Gardner, Stephen A. Miller, Shosei Serata

The Bryan Mound salt dome in Freeport, Texas, has some of the largest and oldest solution caverns in the U.S. There are a total of five caverns of varying shapes and sizes randomly distributed throughout the salt dome. When the caverns were converted from a brine production to an oil storage operation, the effects on long-term stability of the caverns and inter-cavern behavior were analyzed to evaluate the future safety of the storage operation. The analysis was based on a worst-possible-case scenario, including accidental wellhead pressure loss. The impact of this pressure loss upon the thinnest partition between the two closest caverns was analyzed, using a case example of storing lightest weight LPG, thereby creating maximum differential pressures between these two caverns. The finite element method with the REM computer code was utilized for this analysis. Results of the analysis illustrate the basic mechanisms of the long-term behavior of the multiple caverns in the LPG storage operation.

Jan 1, 1985

By O. P. Arora, J. B. Darby, Paul A. Beck

LAVES and Wallbaum' reported that the phases occurring at the compositions TiFe, TiRu, and TiOs, which are stable over a wide range of temperatures and are separated from neighboring phases by wide two phase fields, have a CsC1-type ordered structure. For TiRu and TiOs, this was recently confirmed by C. B. Jordan.2 Recent results of Greenfield and Beck3 show that solid solutions with ruthenium of the body-centered-cubic elements vanadium and tantalum (and presumably also of colum-bium) in group Va of the periodic table undergo CsC1-type ordering. Although detailed phase diagrams for these systems are not yet available, it would appear that these ordered structures are separated from the neighboring body-centered-cubic solid solutions by relatively narrow two phase fields.

Jan 1, 1957

By Porter W. Shimer

The solution used in the following method for phosphorns-determination is the filtrate obtained in the nitric and sulphuric acid method for the determination of silicon (Transactions, vii., 346). This filtrate, being easily and quickly obtained, and always quite free from silica, is a desirable one for phosphorus-precipitation. IN order, however, to get all the phosphorus in a precipitable form the solution must be made under conditions more strongly oxidizing than simple solution in boiling nitric acid. In a solution thus

Jan 1, 1889

By John Birkinbine

The following data, collected during a visit to the Snake river district, in Idaho, arc offered as indicating the possible utilization of a water-fall for irrigation by pumping, the working of gold-placers, the generation of electricity for light and power, and possibly for manufacturing purposes. For irriga-

Jan 1, 1901

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world's resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy's law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950's, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

NEW MEMBERS The following list comprises the names of those persons who became members during the period of May 10, 1918, to June 10, 1918. ABEEL, GEORGE H., JR., Cons. Min. Engr., .4111 Lafayette Ave., St. Louis, Mo. ALLEN, CARL A Metal Min. Engr., U. S. Bureau of Mines, Butte, Mont. BECKER P. FRANK Engr., Lightner Min. Co., 35 Nassau St., New York, N. Y. BOCK, JAMES H., Steam Shovel Foreman, Chino Copper Co., Santa Rita, N. M. CARRON, FRANK X., Civ. and Min. Engr Rock Springs, Wyo. CROWE, THOMAS B., Mill Supt., Portland Mill, Portland Gold Min. Co., Victor, Colo. DOBSON, PERCY GRENSIDE, Min. Engr. and Geol., Crow's Nest Pass Coal Co., Fernie B. C., Canada. ESTABROOK, W. H., Capt., 3d Bat. 20th Engineers, A. E. F., Care postmaster, N.Y. FRASER, 0. B. J., Engr., International Nickel Co. of Canada, Ltd., Port Colborne, Ont., Canada. GARRIDO,. MANUEL F., Min. Engr 109 W. Myrtle St., San Antonio, Tex. GRODSKY, VLADIMIR ALEXANDROVITCH, Cons. Engr., Motor Products Corpn., Detroit, Mich.

Jan 7, 1918

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

By Theodore H. Eyde

The porphyry-copper province of southwestern United States and northern Mexico constitutes the largest copper-producing region in the world. More than 20 deposits discovered since World War II are being exploited or in the process of exploration and development. Because of the remarkable success in discovering new deposits, exploration activity continues at a very high rate and deeper targets are explored each year. Exploration programs for deeply buried porphyry-copper deposits require a reevaluation of the conventional exploration techniques. Though surface induced-polarization techniques have about reached their practical detection limit, aeromagnetics will play an increasing role in the exploration activity as will downhole logging tools. In addition to a valid geological concept, any successful exploration program for porphyry-copper deposits in the southwest must have two other essential ingredients: money and guts. Unfortunately many exploration programs in the southwest are underfunded and doomed to failure. Future exploration will demand more joint venturing in which larger and more expensive exploration programs can be successfully funded by groups of companies or syndicates.

Jan 1, 1975

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.'-' 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate'- or if past production performance has been subjected to abrupt variations in the production rate."' 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By A. D. Hoagland

The Flat Gap mine is located on Copper Ridge in the Appalachian Valley of East Tennessee. Large zinc orebodies occupy zones of solution and collapse breccias in Lower Ordovician Kingsport limestone and dolomite. The principal ore mineral is sphalerite and the principal gangue is dolomite. The ore-bearing horizons are considerably more than 95% covered by thick residual clay. Geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap mine. The Flat Gap mine, an important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolcrmite and accessory pyrite. There is local minor galena and very rare barite and fluorite. The ore-bearing horizons are covered by about 20 to 100 ft or more of residual clay except where active streams have exposed bedrock. Considerably less than 5% of the favorable host rocks are exposed in outcrop, and this nearly complete soil cover creates a serious obstacle to exploration. Comprehensive surveys of the base metal content of soils furnish a useful substitute for outcrop geology, and under favorable conditions, this technique is a very valuable prospecting tool. The analysis is carried out by a titrametric dithizone method modified after the procedure described by E. B. Sandell.' This method detects

Jan 1, 1962

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb'24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.' as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant' on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,' aging took place during the creep tests. 'In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500' or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500' or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40' to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.' At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960

By J. H. Henderson, T. E. Morrisson

An irvestigation has been made of the production of oil through horizontal fractures of high capacity and large radius placed at the base of producing formations. The specific aitns of the study were to (I) determine by model studies the reservoir performance when gravity drainage is the only producing mechanism, and (2) develop a method of predicting such perfortnance from commonly measured reservoir proper-ties. Although the theoretical approach tailed to develop a rigorous analytic sorution to the transient problem, it (lid lead to a practical method of predicting performance. Predictions (Ire in good agreement with rates and recoveries observed in scaled-model experinzents. Capillary effects and the influence of relative permzenbil-ity are taken into account. The experimental program was mainly concerned with the influenre of fracture radius, fracture capacily and capillary hold-up on the total recovery and the rate of recovery. Much of the experimental work was done on a triangular model which represented one-eighth of a square well pattern, so constritcted that horizontal fractures of varying radii and flow capacity could be studied. An electrolytic model was used to relate the initial production rates to fracture radius, formation thickness and the drainage radius of the well pattern. The conclusions reached as a resrtlt of the work are as follows. I. The production of oil under gravity force alone into a well-propped horizontal fracture, whose radius is of the order of hundreds of feet, is a recovery method which combines high recoveries with very acceptable production rates. 2. The mechanism is effective in "dead oil" reservoirs as well as in reservoirs which possess the energy of solution gas. 3. A method of predicting performance has been developed which gives good agreement with experimental behavior in cases of practicnl interest. Even for very thick beds and large fracture radii, where actual conditions do not conform to the assumptions made, the method gives order of magnitude predictions which would not otherwise be possible. INTRODUCTION Gravity drainage of oil from a formation which has continuous ver- tical permeability over a reasonable depth interval is a surprisingly effective method of recovery. However, for a conventional well the production rates which result from gravity drainage are so low that the economics are seldom attractive. The same formation may produce rapidly and profitably by gravity alone through a high capacity, extensive (i.e., > 100-ft radius) horizontal fracture placed near the bottom of the pay section. Fig. 1 shows a schematic diagram of the plan. Energy in the reservoir gas is not a necessary condition for this recovery process. With a sufficiently large fracture, attractive production rates will result from gravity flow alone, and the producing GOR need only be the solution GOR. It is, of course, necessary to keep the fluid level in