Search Documents

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By N. J. Grant, D. S. Bloom

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Project Manager or Construction Engineer, 48, married. Twenty-five years' experience on mine, mill and smelter construction work, design and operation, U. S. and Mexico. Speak Spanish. Now employed; available 30 days notice. Prefer U. S. or Mexico. M-698-489-E-1-San Francisco. Mining Geologist, 53, single. Eleven years' intensive field experience giving a completely practical competence for the smallest or largest of areas; plus the highest possible grade of academic background and independent research qualifying for top rating. Available in thirty days or less. Any location acceptable. M-699-3611-E-7-San Francisco.

Jan 1, 1952

By R. G. Davies

THE effect of ordered structures upon steady state creep has not been extensively studied although it has been demonstrated that the brass,' ie,' and Fe3Al3 superlattices increase the creep resistance. Suzuki and Yamamoto observed an acceleration in the creep rate of Ni3Fe below the critical temperature for order, (T, - 505"), for both the ordered and disordered states, and that the activation energy for creep was independent of the applied stress. They concluded that a dislocation climb creep mechanism was operative down to 300°C which is - 1/3 TM where TM is the absolute melting temperature. This is quite remarkable in that it is usually observed that climb controlled creep in both pure metals and alloys ceases below - 1/2 TM (590" for ie). With this anomaly in mind it was decided to reinvestigate creep in a 75 at. pct Ni-25 at. pct Fe alloy. The creep apparatus and operating conditions have already been decribed. Since Ni-Fe alloys order very slowly, it is possible to have a disordered alloy at a temperature below T,. A long anneal at a temperature just below T, produces considerable long-range order;5 the ordering treatment in the present investigation was 150 hr at 485°C which gives an antiphase domain size of-SOW

Jan 1, 1963

A joint statistical report released by the U.S. Department of Commerce and U.S. Securities and Exchange Commission indicates that business investment in new plants and equipment is expected to total $81.8 billion during 1971. This figure is based on the findings of a survey conducted in late April and May and reflects about a 1 ½ % decrease in investments from the $83.1 billion projected in February. Mining, on the other hand, is still in a bullish mood and is expected to spend $1.99 billion in 1971 compared to $1.89 billion in 1970 and $1.86 billion in 1969. Based on figures quoted above, mining investment in 1971 should show a 5.2% increase over 1970. Carl E. Bagge, president of the National Coal Association, was the dedicatory speaker at the new Milton R. Young Station of the Minnkota Power Cooperative in North Dakota. This new power plant incorporates many innovations which have overcome the problems of using the low-cost lignite abundant in the area. According to Bagge, this development and President Nixon's recent request for an extra $10 million for coal gasification plants is helping the region lead the way in providing for the power needs of the future. He also maintains that gasification of coal can reconcile coal consumption with the demand for cleaner air, and also assure the nation of adequate pipeline gas.

Jan 1, 1971

[ ] (14) SCREENS: Description of Allis-Chalmers' complete line of vibrating screens for the mining industry is contained in a new 8-page bulletin. Primary scalping, secondary scalping, and conventional screens for wet or dry sizing and screens for heavy media separation are included. Also given is a typical fiowsheet showing how horizontally operated Low-Head screens are used in the sink and float process. (15) MILLS: Forty-six years of experience and 4000 installations throughout the world lie behind the seven basic types of mills illustrated in a recent bulletin from the Hardinge Co. Fields of application and materials handled in various installations are listed. (16) BLOWERS & COMPRESSORS: A brochure describing the manufacturing facilities and the axial and centrifugal blowers and compressors made by the Sawyer Bailey Corp. is now available. (17) LINATEX: The first catalog of the Linatex Corp. of America has been issued, outlining the advantages claimed for this special form of natural rubber, when used in corrosion, abrasion, and vibration resisting applications. (18) WIRE ROPE: Twenty-four pages packed with concentrated wire rope data is the way E. H. Edwards Co. describes a booklet which they are now making available. It was condensed from the Edwards general catalog to provide users with a concise guide to every important phase of wire rope production, maintenance, and use.

Jan 1, 1952

By Arthur A. Center

World production of electrolytic zinc has shown an increase for each year since 1932. Production up to 1936 was summarized in my earlier paper [Trans. A.I.M.E. (1936) 121, 453-4641, and this present paper carries the subject through 1943. During this time of increase, it is safe to say that the average purity has been raised more or less continuously, and the amount of four-nines metal has been in- creased. While the period reflects preparations for and the carrying on of the present war, electrolytic zinc proved its value in many industries as a peacetime metal in the years from 1919 to 1940. World production (Table I) increased from about 594,000 tons in 1936 to around 858,000 tons in 1943; United States production increased from 127,171 tons to 329,903 tons for the same years. Total production of primary zinc in the United States is given in the first column of Table I; retort production of primary zinc, obtained by difference, in the last column. The curves drawn from these figures are shown in Fig. I. They represent continuations of the curves in the earlier paper that cover commercial production of electrolytic zinc from its inception in 1915 to 1935. The earlier paper gave data for total world production and foreign retort production (calculated therefrom) and showed curves of electrolytic vs. retort production

Jan 1, 1944

By L. K. Jetter, C. J. McHargue

DEVELOPMENT of preferred orientation in uranium is of interest because of the strongly anisotropic properties of the orthorhombic crystal structure. Harris&apos; reported inverse pole figures for rolled uranium rods which showed <010> and <410>* to be parallel to the rolling direction after On 0.19-in. spherical X-ray diffraction specimens taken from the center of the middle section of each rod, pole distribution data were obtained by the spectrometric method described previously.4 The specimen was rotated rapidly about the axis coinciding with the rod axis in order that a large number of grains could be scanned and was rotated slowly about an axis perpendicular to the rod axis. The variation in the diffracted X-ray intensity was recorded as a function of the latter motion (angle 4). Fiber-axis distribution charts (inverse pole figures) were prepared by the method described by Setter, McHargue, and Williams." After having been corrected for background radiation, the pole distribution data (I vs ?) were normalized. A normalizing factor for each plane has been shown to be Iranaom = f I sin 4 ? 4 and was obtained by graphical integration from the data for that plane plotted as I sin ? vs ?. The axis-distribution charts deduced from the normalized pole densities are shown in Figs. 1 to 3. On these charts, the contours indicate angular positions of equal normalized axis density,

Jan 1, 1958

By M. J. Salkind

In discussing the possible contribution of plastic deformation to neck growth during sintering, Wilson and Shewmon State that Lenel, Ansell, Salkind, and Early34, 35 concluded that dislocation flow is the rate-controlling process in sintering under zero external load. The experiments cited34, 35 were done with applied external loads, and the conclusions were that the same kinetics could be controlling sintering due to the force of gravity with no additional applied load. The effect of gravity on sintering behavior was previously cited.34, 31 In addition, Wilson and Shewmon argue that the conclusions of Refs. 34 and 35 are doubtful because the strain rate is proportional to stress for plastic flow. This assumption is true only for certain kinds of plastic flow such as Nabarro-Herring Microcree38 As Early, Lenel, and Ansell point out3&apos; plastic flow, based upon dislocation movement, can exhibit strain rates which exhibit a power law relationship to the applied stress.39, 40 Wilson and Shewmon also doubt the results of Refs. 34 and 35 because the stresses in the necks are too small for x/a > 0.1. This is true, and the experiments described in Refs. 34 and 35 were done for small values of %/a. The conclusion was that plastic flow by dislocation movement was important during the early stages of sintering when x/a is small.

Jan 1, 1968

Shovel To further increase the efficiency in the production of their foundry sand, the American Silica Sand Co. has purchased a new and improved shovel that will be used for loading trucks at their Reynolds Pit. The [ ] new shovel will greatly facilitate winter mining operations and make possible larger winter shipments of the company&apos;s foundry sand. The Reynolds Pit is one of three sand pits in the Ottawa district owned by American Silica which produce sand that is refined for foundry use. Circle No. 1 Electric Switches The Crane Electric Co. has just announced the production of their R-1000, a new rotating limit switch designed to control the travel of any rotating device requiring interruption or establishment of electrical current after a predetermined number of revolutions. It is useful for machinery, lifts, and other power equipment. The switch is presented in a finished case, 16 gage, reinforced, with walls of sufficient strength to hold the entire mechanism and all the parts in accurate alignment. The worm gear combination has a 60 to 1 ratio, sufficient for most industrial uses. The number of revolutions can still be increased by using various combinations of driving sprockets, either on the shaft of the switch, or on the sprocket of the unit controlled by the switch itself. Circle No. 2

Jan 1, 1952

By P. K. Guerrero, Nathaniel Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere. This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors, and more recently by Rose. This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis&apos; result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically.

Jan 5, 1960

By I. Ionel Gardescu

During the latter part of 1930 an agreement was reached among operators in Rumania to curtail the production of oil to about 100,000 bbl. per day. This agreement lasted only a few months and 1931 shows a new peak in production with an average yield of 136,900 bbl. per day as against an average of 116,600 bbl. per day for 1930. The total production for 1931 was 49,210,000 bbl.; an increase of 18.4 per cent over the previous year&apos;s production. It is interesting to compare the percentage production of the major companies to the potential production figures determined by the Government in September, 1930 (Table l), on the basis of which the proposed curtailment was to have been made. The three companies listed first in this table show an increase in average production for 1931 over their estimated potential production rating. This increase might be attributed at least in part to the recent development of the Boldesti field, which is controlled by these companies and of which the production at present is nearly 10 per cent of the total oil output for Rumania. Among the other fields, Moreni still holds first place with an output of 33.6 per cent, followed by Gura-Ocnitzei with 29.3 per cent. In both these fields the main source of oil is from the deeper Meotic sands. Other

Jan 1, 1932

By Ivor E. Campbell

The Smelter Control Research Association, Inc. (SCRA) was established in 1971 by domestic primary copper producers to investigate processes for removal of sulfur oxides and particulates from copper reverberatory furnace stack gases. The Association maintains a continuing review of developments related to sulfur oxide and particulate control technology, and conducts pilot-plant-investigations of scrubbing processes with feed streams of copper reverberatory furnace off-gases. In its first year of operation, SCRA reviewed over 100 processes proposed for sulfur dioxide removal. As could be anticipated, the frequency of receipt of proposals relating to improvements in sulfur, dioxide control technology has now declined. However, the number of such proposals still being received indicates continuing research on both wet and dry scrubbing systems, and indicates a widespread awareness, of shortcomings of proposed control. Despite the fact that an almost unbelievable number of processes has been proposed for sulfur dioxide control, few have progressed beyond the conceptual stage, and only a limited few have been subjected to thorough pilot-scale evaluation. The most extensive pilot-scale and demonstration-scale investigations have been. devoted to the so-called throwaway processes employing limestone or lime slurry scrubbing. This work has, in turn, for the most part been on utility plant stack gases, containing from 500 to 3,000 ppm sulfur dioxide.

Jan 1, 1976

By Harry E. LeGrand

Most mine operations are hampered to varying degrees by excessive inflow of water into mines or scarcity of water for processing the materials. These internal problems are compounded in many cases by such external hydrological problems as lowering of ground-water levels in areas outside the mine properties, subsidence of ground surface, adverse geochemical changes, and pollution. The development of a mine below the water table disturbs the natural ground-water system, causing a convergence in the flow of water from a surrounding area. The mine becomes the apex of a depressed cone in the water table. The fact that mines are commonly located in complex and somewhat anomalous geologic environments prevents an idealized treatment of the mine as a well that would be similar to a water well in a homogeneous aquifer having isotropic conditions. Yet, adherence to some principles of ground-water behavior is helpful when combined with an understanding of the local geology. A program calling for an appraisal of all pertinent hydrological conditions prior to mining and during various stages of development should supply adequate information for mine officials to anticipate difficulties and to allow for corrective measures. Before and during mining operations there should be a mine hydrology framework and plan, in which there is continual upgrading of such considerations as anticipated actions, consequences of actions, remedial plans, and contingencies.

Jan 1, 1973

HAVING told you about steel in the previous chapter, it seems to me necessary to speak here of brass for the same reason, for it bears the same relation to copper that steel does to iron. It is the opinion of some concerning both of these that they are true minerals because Pliny in his Natural History calls it aurichalcum and says that it has its own ore; he does not say, however, where it is found, and I have not heard from anyone else that it has been found anywhere, and, surely, if it had been found when he wrote, it would also be found today. Since I have no knowledge other than that gained through my own eyes, I tell you as a certainty that just as steel is iron converted by art into almost another kind of metal, so also brass is copper given a yellow color by art. Surely it was a splendid discovery, for which we must praise the alchemists,* although perhaps whoever discovered it was deceived, thinking that he had made gold from copper. Now, in short, this work requires infinite labor, and is carried out in various places, for instance, in Flanders, Cologne, Paris, and in many other countries, and also in the city of Milan in Italy, where I have seen a

Jan 1, 1942

Copper from Central Africa was well known to the Arab slave traders who depredated the country in the nineteenth century. By the 1870&apos;s slave raiding was so intense that the habits of the tribes were disrupted, and they no longer worked the copper deposits or made the crosses and bars of copper which had been their custom. In fact, the country had been greatly depopulated by the slave raiders. News of this horror was spread to the civilized world by missionaries and, in particular, by David Livingstone&apos;s writings. Whether to extend geographic knowledge, to suppress slavery or for national aggrandizement, the rush for African territory was on at the end of the nineteenth century. Cecil Rhodes at this time was established by his successes in diamonds and gold. He obtained the blessing of Lord Salisbury in 1889 to form the British South Africa Company under crown charter. His objectives were to occupy the lands north of the Zambezi for England and pay for development out of the country&apos;s mineral deposits. He planned to occupy the territory and close the gap to form an all-British route from the Cape to Cairo, one of his great dreams. With this master plan in mind he sent his agents into the field to make treaties with the tribes.

Jan 12, 1962

By M. C. Fuerstenau, W. F. Cummins

The flotation response of quartz in the presence of calcium chloride and various fatty acids is presented. Flotation is not effected with lauric acid until calcium laurate is precipitated in solution, while flotation is obtained with the 9, 10, and 11-carbon members before precipitation of the calcium carboxylate. The active species responsible for flotation is suggested to be a basic aqueous complex, e.g. Ca(OH) (RCOO) (aq), and a possible mechanism of adsorption is given. Most of the previous work on activation in non-metallic flotation systems has involved the use of high molecular weight collectors, such as oleic acid or alkyl aryl Sulfonate.1-7 In these studies the levels of addition of collector and activator required for flotation were much above the concentrations necessary for precipitation of the metal-collector salt. In fact, Clemmer, Clemmons, Rampacek, Williams, and Stacy1 have stated, "Our experiments on a variety of materials have demonstrated that the metal salts which react with anionic collecting agents, as soaps and alkyl sulfates, to form relatively insoluble compounds may be employed as activating agents provided an optimum quantity is used at a proper pH." On the other hand, Gaudin and chang8 obtained flotation with additions of barium and lauric acid below the level required for barium lautate precipitation.

Jan 1, 1968

By Paul Hett

The much-heralded Deep Ruth operation of Kennecott Copper Corp., at Ruth, Nev., is scheduled to become a producer by 1957. Inaugurated as a project in 1951, production was originally scheduled to start in 1953, but excessive water hindered shaft sinking. A revised schedule called for output by 1955, but again plans had to be changed. This time the change was to permit mining of an orebody that would have otherwise been lost because of block caving methods planned for the main deposit. The new ore is within the cave limits of the larger orebody, above the first production level. Ore will start coming from this new source in 1956, a year ahead of the principal operation. (See NEWS, page 344.) There is little doubt that current economic conditions and unforeseen expenditures for early shaft development will make the Deep Ruth a high-cost producer. Yet, some of the drawbacks of the Kennecott operation may be mitigated by the possibility that additional exploration will increase the already assured 25 million tons of 0.83 pet copper ore. While Kennecott is missing out on the current high copper market and is thus left with a potentially narrowed profit, the predicted demand for copper has created an optimistic feeling. Its development is certain to enlarge known U. S. copper reserves and significantly extend the life of Kennecott&apos;s Nevada operations.

Jan 4, 1955

By R. G. McQueen, E. G. Zukas

THE production of isotropic fine-grained ingot iron would be most useful since physical measurements associated with the elastic properties of iron are influenced by the size and orientation of the individual grains. This can be accomplished at present for small samples by established metallurgical procedures, but for large samples (in excess of 2 in. diam by 1 in. thick) it is virtually impossible to produce reasonably small uniform grains with random orientation. Such pieces can, however, be produced by impulsive loading followed by a suitable recrystallization treatment. The shock loading system employed is diagrammed in Fig. l. Here the 3/8-in. iron plate is accelerated by the plane-wave initiated high explosive charge through a 1 5/8-in. air space. Collision of this plate and the specimen of interest generates a shock wave in excess of 300 kbars which passes through the specimen. For this type of work it is not necessary to use machined parts: for example, the ingot iron pieces are saw cut from the billet so that they can be inserted in short sections of iron pipe. The recovered specimens are less distorted, however, if the air gap between the iron sample and pipe is filled with Woods metal. The dimensional changes resulting from this type of loading technique are minor, usually less than a 10 pct reduction in thickness. Compressive yield

Jan 1, 1962

By G. E. Agar

The energy required for dry grinding of phosphate rock in ball and roller mills has been analyzed by the method suggested by Charles and others. The findings are not wholly in agreement with Charles&apos; predictions; but, nevertheless, the method of analysis is shown to be sound. Some of the deviation is probably attributable to the characteristics of a dry grinding system. Many laboratory and pilot plant scale experiments have been made to determine the energy requirements for size reduction. This topic was recently reviewed by Agar and Brown&apos; and it was apparent that very little if any data exists in the literature which permits one to apply the Charles 2-Holmes3 analysis to industrial size systems. More recently, the idea has been put forward that the postulate of comminution by impact used by Charles and others was not sufficient to explain size-reduction throughout the grinding operation. The opportunity exists in the grinding operations of International Minerals and Chemical Corp. (IMC) to analyze the energy-size relationship for dry grinding phosphate rock in both ball and roller mills. This situation arises because the mills are used for custom grinding and make products from 50% to 85% minus 200 mesh. BACKGROUND A correlation of particle size in a comminuted material with the energy expended in size reduction was proposed by charles2 to be of the form

Jan 1, 1965