Search Documents

By J. J. Hauser, H. C. Theuerer

A cathode sputtering technique is described which elin7inates the need for ultrahigh vacuum in preparing thin films of materials sensitive to gaseous impurities. This technique uses a fraction of the atoms sputtering within an anode container to getter actice gases, such as HzO, Oz, and Nz. The gases alzd gettering metal are deposited on the container walls, thus shielding the coating zone of the system from contamination. The use of the method for preparing superconducting-normal metal couples such as Ph-Cu and Ph-Pt is described, and the properties of the individual and composite films are given and discussed. GETTER sputtering is a method which greatly simplifies the preparation of thin films in cases where composition control is critical. A major difficulty with conventional sputtering and other vacuum-deposition techniques is the contamination of the forming film caused by residual gases, such as H20, CO, Oz, and Nz, in the coating equipment. The difficulty arises from the fact that even when the residual pressure in the system is as low as 1 x 10"6 Torr, with a deposition rate of 10A per sec, there are as many contaminating gas collisions with the substrate as there are with film-forming metallic atoms. It is not surprising, therefore, that with reactive metals, such as tantalum and niobium or with semiconductors, such as silicon and germanium, films with properties far different from the starting materials are obtained. In the case of niobium and tantalum, deposited either by sputtering or vacuum evaporation in systems with reactive gases at pressures of the order of 1 x l0-' Torr, the loss of superconductivity is traceable to interstial oxygen or nitrogen. On the other hand, working in vacuum of the order of 1 x l0-" Torr, Marchand and enema' have shown that superconducting films of tantalum with properties approaching those of bulk material are possible. At this level of gaseous impurities -lo6 metallic atoms arrive at the substrate before a contaminating collision occurs again assuming a deposition rate of 10A per sec. It is evident from the above that any successful vacuum technique requires the elimination of reactive gases from the region of the system where coating is occurring. Getter sputtering accomplishes this using conventional vacuum equipment with residual pressures in the 106 Torr range. In fact? vacuum systems with residual pressures of lo-" Torr are adequate for most purposes. With this method, sputtering is confined within an anode can and, by geometric design, sputtering itself is used to purify the argon at the lower and upper parts of the system by the gettering action of the reactive metal. In consequence, the central region of the system where coating occurs is shielded from gaseous contamination. Getter sputtering is particularly useful for the preparation of alloy and compound films. With this method, if a cathode of homogeneous composition is bombarded with high-energy argon ions, transfer of material to the substrate having the same composition as the cathode will occur. This is true after an initial equilibration time, even though the constituents of the cathode may have different sputtering rates. During equilibration, the surface of the cathode changes composition due to differences in sputtering rate, but mass conservation demands a steady-state condition such that the atoms sputtered from the surface have the same composition as the cathode material from which the surface is generated. GETTER-SPUTTERING APPARATUS The original form2 of the getter-sputtering apparatus is shown in Fig. 1. It consists of a closed nickel or stainless-steel can 4 in. tall and 2-3/8 in. in diameter. Mounted symmetrically from each end

Jan 1, 1965

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction .within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress.4,5? The theory of recrystallization is not in advanced state; if recrystallization data were obtained, in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By Nicholas J. Grant, Rolf Nordheim, Thomas B. King

Constant-load creep-rupture tests were conducted in an argon atmosphere at temperatures of 1600 to 2200°F on two heats of iron containing about 0.06 and 0.09 pct P in solid solution. The tests were conducted in the as-cast condition. Stresses were selected to give strain rates approaching those encountered in the hot working of steel, and within the limits of the creep-rupture test apparatus, namely. from about 0.001 to 50 pct per sec. FOR generations, rolling and forging practices have been developed largely by empirical methods, based on prior experience. While largely successful, difficulties are frequently encountered when new or different alloy compositions are tried for the first time. There is need to know the relationships which exist among temperature, strain rate, composition, and other variables on the deformation and fracture characteristics of steels. It has been shown for aluminum and several high-temperature alloys that the deformation and fracture characteristics follow rather well-defined laws and patterns which are closely related to the effects of strain rate, temperature, and composition.1"3 As the melting temperature of aluminum or its alloys was approached, it was possible to study the interplay of work-hardening factors and recovery or recrystal-lization, the latter resulting in improved ductility and increased resistance to intercrystalline fracture. In particular, the effects of composition are very poorly known. Within the meaning of "composition" should be included impurity elements, such as sulfur, phosphorous, lead, copper, and many others, as well as those elements which are added for alloying purposes in iron. The role of multiphase structures, in contrast to solid solutions, should also be studied in much greater detail. high strain rate creep-rupture tests would provide information regarding the deformation and fracture characteristics of metals at hot-working temperatures. It was also desired to establish the stresses which are necessary to accomplish the desired deformation, and to relate these to the strain rate and temperature. Secondly, it was the purpose of this particular study to determine the effects of phosphorus, within solid solution limits, on the deformation and fracture characteristics of iron at hot-working temperatures. EXPERIMENTAL PROCEDURE Two phosphorus levels were selected, one corresponding to the upper limit normally found for commercial steels, and one substantially higher than this, but within the region of solid solubility at the test temperatures chosen for this investigation. Twenty-pound heats were prepared by induction melting electrolytic iron in air in a magnesia lined furnace. After deoxidation with about 0.2 pct Al, ferro-phosphorus was added, and the heats were then poured into prefired silica molds. The purpose of using silica molds was to obtain a slow cooling rate during solidification to produce a relatively coarse grain size, producing a structure subject to some segregation and therefore more nearly characteristic of ingot structures. The major part of the casting assembly provided a large shrinkage head in order to produce sound castings and to promote slow cooling of the specimens. The primary austenitic grain size varied from ASTM No. 2 to No. 00. The composition of the heats, including a low phorphorus melt, used for comparison purposes, is shown in Table I. It will be noted that the oxygen content of the phosphorus containing heats is relatively high, in spite of the deoxidation practice, a condition which is difficult to control in small melts. Creep-rupture tests were nevertheless undertaken when it was noted that this quantity of oxygen did not appear to give results any different from those from a heat containing 0.01 pct 0, low phosphorus and comparable carbon Content;4 see Table 11.

Jan 1, 1961

By HENRY FA

HENRY FAY (communication to the Secretary*).-In reply to the discussion of my paper, I wish to take this opportunity to express my appreciation to the Chairman and the various gentlemen who have taken part. I regret that others have not offered criticism, for honest differences of opinion often lead to the truth, and suggest new lines of work. An experiment has been made which bears on Prof. Sauveur's discussion and which helps to emphasize the conclusion that cementation is not a factor in the hardening of: the surface. Dr. Langenberg, of the Watertown Arsenal, has heated for me, in vacuo at 1,000° C., a piece of the metal containing a hard surface. The microstructure shows uniform distribution of carbon throughout the metal, showing that no carbon has been added to .the surface and heating in vacuo has prevented any oxidation of the surface.

Jan 6, 1917

By F. R. Morral

HOT-DIPPED heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature of the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped FIG. I.-SYSTEM IRON-ZINC ACCORDING TO J. SCHRAMM.11 heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schueler1 by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva-nized wire, which was assumed to be the FeZn10 phase.

Jan 1, 1940

By Robert W. Bartlett

A computer model for predicting the rate of oxidative leaching of copper from fragmented low grade sulfide ores is presented. The model involves the kinetics of the dissolution of chalcopyrite grains and solution diffusion of oxygen within rock pores. Adjustable curve fitting parameters are not used. The model was tested by comparing computed extraction curves with experimental results for a -11 inch ore obtained by block caving and leached at 90°C and 400 psi oxygen for one year at the Lawrence Livermore Laboratories.

Jan 1, 1973

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By C. H. Ault, D. D. Carr

Four counties in Indiana- LaPorte, Vigo, Vanderburgh, and Switzerland-have potential for deep underground limestone mining because they are in or near high population areas and have no surface-mineable limestone deposits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Mineable seams suitable for aggregate are 120-150 m (400-500 ft) below the surface in LaPorte and Vigo Counties, about 90 m (300 ft) below the surface in Switzerland County, and about 600 m (2,000 ft) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1983

By Gilbert P. Moore

Production in the Argentine in 1930 amounted to 1,415,099.7 metric tons, which converted into barrels of 42 gal., using the factor of 6.29, amounts to 8,909,773 bbl. This is a decrease of 481,613 bbl. from the 1929 production, which was 9,391,386 bbl. The production for 1930 was divided among three fields, as shown in Table 1. Table 2 covers Table 1.—Argentine Oil Production, 1930, by Fields Barrels Comodoro Rivadauia District Government........................................... 4,547,670 Railways Co........................................... 1,314,358 Astra-Eastern......................................... 1,016,024 Anglo-Persian......................................... 365,021 Solano Co............................................. 24,613 Dutch Shell........................................... 6,963 7,274,649 Neuquen District Government........................................... 569,245 Standard Oil-Argentina................................. 659,551 Astra-Eastern......................................... 8,234 Challaco Co. (Sol)...................................... 121,598 1,358,628 Salta District Government........................................... 90,576 Standard Oil-Argentina.................................. 185,920 276,496 8,909,773

Jan 1, 1931

By Waldemar Lindgren

CONTENTS. [ ] I. INTRODUCTION. THE precious metals, gold and silver, are the basis of the monetary systems of the world. It is, therefore, natural and inevitable that widespread interest should be manifested in their production and in the various classes of deposits in which they are contained. At times a great scarcity of the precious metals has prevailed; at other times the production has seemed so abnormally large that fears have been entertained regarding their ultimate retention as standards of value. Since most nations have adopted the gold standard, and the remaining ones appear likely to do the same in the near future, the question of available supply of gold for the present and future very naturally arises. This necessarily involves a consideration of the characteristics of the gold-deposits. After the absorption of the gold treasures of the New World by the conquistadores, the gold-placers of Brazil and Russia

Jan 1, 1913

By Ronald L. Longwell

PROPERTY LOCATION Located in the Copper Creek area of the Galiuro Mountains, the Old Reliable is on ground first claimed for mineral value during the Civil War. The deposit was mined sporatically from 1880 to 1919 and again in 1953 and 1954, with a total of about 30,000 tons of ore removed. The ore body is a near vertical breccia pipe containing approximately 4,000,000 tons of 0.80% copper with mineralization occuring as chalcocite, chalcopyrite, malachite, chalcanthite, and chrysocolla. The host rocks are extrusive lavas of cretaceous age which were intruded and mineralized by Copper Creek Granodiorite, which is Laramide in age. The ore zone, which occurs on the toe of a ridge, is about 300 feet by 600 feet in plan, with the bulk of the deposit extending from the surface to a depth of 500 feet.

Jan 1, 1974

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan, the primary constituent, and a water-soluble dispersant, under the trade name Pennfloat™ 3. * Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the variables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors. The reagent was shown to be a highly effective and versatile collector on virtually all of the more than 30 sulfide ore types examined.

Jan 1, 1982

By M. Muskat, H. H. Evinger

A METHOD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous- fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permeability data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should have significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast.

Jan 1, 1942

By Thomas M. Drown

ZING is, as is well known, very brittle at a temperature of about 210' C. (410' F.), and may then be readily pulverized in a mortar. By sifting it may be obtained of uniform grain. I have been accustomed to prepare products passing through 40, 60, and 80-mesh sieves, and also by bolting through a fine handkerchief. The principal analytical uses to which I have hitherto applied this material are to the reduction of iron directly from the ore by heating it with the pulverized zinc, and the reduction of ferric to ferrous compounds in solution. In the first case the pulverized ore, 0.5 gram or less, is intimately mixed with about ten times its weight of the pulverized zinc (the finer the zinc the better), in a porcelain crucible, and this mixture is covered with about the same amount of zinc. The crncible is then heated at the top of the flame of a Bunsen bhrner, at a dull red heat, for about ten minutes. The crucible should not be covered. When cool, the crucible, with its contents, is placed in a flask treated with hot dilute sulphuric acid, and brought quickly to a boil. The zinc and reduced iron are dissolved in a few minutes and the flask is then tightly corked and allowed to cool. When cool, the iron is directly titrated by potassium permanganate.

Jan 1, 1879

By T. P. Meloy

In a recent paper, Gaudin and Meloy1 derived a size distribution function for single, impact fracture. Mular2 extended the use of this size distribution to describe the output of carefully controlled grinding experiments. As it stands, the function is difficult to compute. Consequently, a series of tables of the function are presented below: where M(x) is the cumulative fraction finer than size x when x is particle size. Weight percents are tabulated for the single parameter, r, in three different size ranges: from 0 to 1, from 1 to 10 and from 10 to 100. Tables I, II and III are cumulative percent finer and Tables IV, V and VI are for weight percent passing screen size x, retained on the screen below. A number of conditions from the table are plotted in Figs. 1 and 2. Fig. 1 is a plot of the cumulative percent finer vs. size, and Fig. 2 is the weight per-

Jan 1, 1963

By R. N. Schulz

The recently completed modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located microprocessor based control system connected to a central control room. Operation of each micro-processors can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1984

W. O. OWEN,* Washington, D. C. (written discussion?). Few people appear to realize that the time to reach the crippled soldier is when he is first hurt. In my own judgment, the best time to reach him is before he is hurt, by showing him what other cripples have themselves clone of their own initiative, without Government-support, rendering themselves self-supporting, able to bear a little bit more than their own weight, so that they may lay aside a little bit for a rainy clay and some for a little fun in

Jan 5, 1918

By J. W. Downey, M. V. Nevitt

The phase boundaries for the 950" isothermal sections in the ternary systems Zr-Co-0 and `Zr-Ni-0 have been determined for the composition range from 50 to 100 at. pct Zr. The two systems show very similar phase relations, having no extensive solid solution phase fields. Each contains a ternary phase. These phases are apparently isostructural, but their structure has not been determined. Some aspects of the phase relations are discussed in terms of the alloying behavior of transition metals. THE work described in this paper is the outgrowth of a recent study of the occurrence of phases having the Ti2Ni-type structure (structure-type E9,) in certain ternary systems involving Ti, Zr, or Hf with another transition metal and O.", In the Zr-CO-0 and Zr-Ni-0 systems no Ti2Ni-type phases were found to occur. However, there are several interesting aspects of the phase relations in the two systems which have significance from the point of view of the alloying behavior of transition metals. The results of this investigation may also have some importance in studies of the oxidation of Zr-Co and Zr-Ni alloys. In both the Zr-Co-0 and Zr-Ni-0 systems only the 950" isothermal sections were investigated and, as a further restriction, the study was limited to the composition range from 50 to 100 at. pct Zr. A tentative Zr-Co binary diagram has been published by Larsen, Williams, and Pehin. In the composition range pertinent to the present work they report a eutectic at 980°C and 75.9 at. pct Zr, the products of which are the terminal solid solution based on /3 Zr and the compound Zr2Co, and a eutectic at 1080" and 64.8 at. pct Zr whose products are Zr,Co and ZrCo. The solid solution based on /3 Zr is shown to decompose eutectoidally at 826°C into a Zr and Zr2Co. The limits of solubility of Co in a and /3 Zr have not been established. The structure of Zr2Co is not identified in the publication just cited. Dwight has reported that ZrCo has the CsC1-type strcture. The Zr-rich portion of the Zr-Ni diagram has been determined by Hayes, Roberson, and Paasche." The phase relations are very similar to those of the ZrCo system. A eutectic reaction whose products are /3 Zr containing 2.9 at. pct Ni and Zr,Ni occurs at 961°c, and a eutectic between Zr,Ni and ZrNi is found at 985". The solid solution based on /3 Zr decomposes eutectoidally at 808°C. The solubility of Ni in a Zr is not known accurately but is believed to be very small. Smith, Kirkpatrick, Bailey, and Williams7 have found that Zr2Ni has a tetragonal structure of the A1,Cu-type and that ZrNi is orthorhombic. Domagala and McPherson8 have published a constitution diagram for the system Zr-ZrO,. At 950" their diagram indicates that the solid solution of 0 in 0 Zr is stable from 0 to 0.5 at. pct while the phase field of 0 in a Zr extends from 6 to 29 at. pct. These solubility limits were adopted in the present study and no binary Zr-0 alloys were made. No previous data on the phase diagrams of the ternary systems are known to exist. EXPERIMENTAL PROCEDURE The experimental details involved in the preparation of alloys in this laboratory by arc melting have been described in several previous papers"3 and they will not be repeated here. Information concerning the purity of the metals used is given in Table I. Oxygen was added in the form of reagent grade ZrO,. All of the cast specimens in both alloy systems were annealed in air-atmosphere tube furnaces at 950 3' for 72 hr and water quenched. The specimens were protected from oxidation by wrapping them in Mo foil and sealing them in quartz tubes that had been evacuated at room temperature to a pressure of 1 x 10B mm of Hg. The phase boundaries were determined by metallography, and identification of the phases was accomplished primarily by X-ray diffraction methods which employed a powder camera having a diameter of 114.6 mm. The diffraction techniques which are in use in this laboratory have been previously described.' An etchant that proved satisfactory for most of the alloys consisted of 5 pct by vol of AgNO

Jan 1, 1962

By L. L. Brundred

The major portion of the production of the Gulf Coast area, represented by South Texas and South Louisiana, comes from the flanks of well-defined salt domes. This oil, containing an excellent lubricating stock, ranges from 17° to 28° Be. gravity. Some lighter oil is encountered but the life of such fields is, in general, an open question. In fact, there are few light-gravity fields which have proved of much value. In all of the fields water encroachment, or, more properly, water produced with the oil, is a vital factor. After the first head of high-pressure gas is removed, ever-increasing percentages of water appear, and naturally the life of the wells is materially affected thereby. The sands are, as a rule, extremely fine, very soft, and must be carefully excluded from the hole by the use of fine screen to prevent sanding up. All sands are tipped at such extreme angles as to make coring essential for the location of water strata, oil-bearing sands and important shale. beds. Even with modern coring, the correlation of logs is a difficult problem. Due to the fact that the bulk of the oil is refined for its lubricating properties, little attention has been paid to losses by evaporation in the field. This is largely influenced by the fact that the major companies have set a price schedule, showing but two grades, "A" and "B." The average oil company, therefore, does not attempt to use the gas-lift but relies primarily on the air-lift and then only on wells considered to be particularly adapted to its use, namely those capable of producing large quantities of fluid and yet not having sufficient "kick" to flow. Furthermore, as the gas contained in the reservoirs is mostly ricthane such gas being very quickly vaporized and produced in large quantity in the early life of the fields, there is little gas left after the first flush flowing period of the wells. In fact, it is very generally conceded that gas is a precarious fuel to depend on in any of the coastal fields. This situation largely accounts for the fact that air, as the lifting medium, is almost universally used. In the average field, wells are drilled on the flanks of the domes in close proximity to one another, largely on account of the extreme dips of the formation and "town lot" leases, and space to set up machinery and

Jan 1, 1928