Search Documents

A. K. McCosh, Coatbridge, Scotland (written discussion*).-It is well known in Great Britain that oven operators in the United States have been able to reduce the coking time much below European standards by the employment of higher temperatures. Our linings have always been the factor that has prevented our doing the same, and it would be of much interest to coke-oven operators here if Mr. Blauvelt would give a typical analysis of the bricks his company uses for the linings of its ovens, and if he could see his way to send me a sample so that I could have the texture examined, I should personally be very much obliged. The lining brick which my company has found most successful is of a ganister variety, and has the following analysis: Silica, 80.8 per cent.; alumina and iron oxide, .17.8 per cent.; lime, 0.8 per cent.; magnesia, 0.07 per cent.; but with this brick the least carelessness on the gas regulator's part may destroy the lining. It would also be of interest if Mr. Blauvelt could give the temperatures of the air leaving these generators and also of the oven flues.

Jan 10, 1918

By G. C. Stone

AS the term "hardness" is used with many different meanings, it should be understood that it here means resistance to deformation by compression. It was determined by measuring the pressure, in pounds per square inch, necessary to reduce by 20 per cent., the length of cylinders 1 in. (25 mm.) in diameter by 2.6 in. (66 mm.) long. The tests were made at Columbia University on an Olsen 400,000-lb. machine, the load being applied at a constant rate of speed 0.0319 in. per min. The results were obtained by Messrs. Rigg and Williams, and some of them were given in a paper read at the Sixteenth Annual Meeting of the American Society for Testing Materials, in June, 1913. The remainder of the results were obtained in subsequent experiments by the same authors. In all cases, the results given are the averages of three or more closely concordant tests. All of the spelters tested were of standard commercial grades and all were of compositions making them good deliveries. The accompanying table gives the results arranged in the order of increasing hardness:

Jan 1, 1919

By R. H. Ernst, H. R. Ogden, D. J. Maykuth

AT present, no theories exist which allow prediction of the effect of alloying additions on the thermoelectric properties of metals. Nevertheless, Battelle and others1 have observed that, at high temperatures, the peak thermal electromotive-force output (relative to a platinum standard) occurs with metals in Group VI of the Periodic Chart. The authors suspected that this peak was associated with the fact that maximum electronic bond stability is achieved with these metals which have six bonding electrons per atom. On the basis of current electron-concentration theory for transition metals and alloys:' it was surmised that the addition of valency electrons to metals of Groups IV and V (accomplished by the addition of metals from Groups VI, VII, or VIII) should progressively increase the thermoelectric-power output of the resulting alloys until an alloy composition is reached at which the number of valency electrons per atom is six. A further increase in the ratio of valency electrons per atom should then decrease the thermoelectric power. In contrast, the addition of bonding electrons to Group VI, VII, or VIII metals should decrease their thermoelectric power since the electron per atom

Jan 1, 1965

By Ossi E. Palasvirta

The authors are to be congratulated for their interesting article, which thoroughly illustrates the variables inherent in filtration of taconite concentrate. The work and the conclusions based thereon largely parallel the test work done by the writer at the Pilotac plant* and the experience gained with a commercial size agitating disk filter in the same plant. At Pilotac, however, a thorough study was also made of the effect of depolarizing (demagnetizing) the filter feed, and it is the purpose of this discussion to comment on the merits of depolarization of the magnetite concentrate prior to filtering. The work at Pilotac was done in three phases: 1) preliminary laboratory testing with a circular filter leaf of 0.047 sq ft, followed by 2) plant testing using a 4-ft diam, single-disk agitating filter that was purchased on the basis of the pilot tests on the 4-ft model. In the laboratory tests depolarization was achieved by slowly withdrawin4 batches of thickened concentrate from a coil producing an alternating field of about 300 oersteds. In plant tests the standard Pilotac procedure1 was employed, wherein the pulp falls freely through the depolarizing coil.

Jan 5, 1958

By Howard S. Strouth

SINCE the days of the Conquistadores, people have told exaggerated tales of the wealth and possibilities of Mexico and Central and South America, and the mining fraternity has never been known to exaggerate any less than any other professional group known to man or beast. However, during a short stay in Mexico one can probably hear more whoppers than at any other time, when dozens of mining propositions are thrust across the desk, and it is not necessary to remind anyone that a listing of the do's and don't's for Mexico requires special mention of the fact that most mining propositions offered south of the border eventually turn out to be a beautiful fairy tale. The following is not suposed to be either an exact description of Standard Mining Corp.'s operations in Mexico by its mining associate, the Corporacion Minera y Beneficiadora Anahuac, S.A., or the last word as to the most economical way to start such an operation. But rather it is the sum total of the recent experiences of the writer while commencing such an operation in 1951-52 with the help of many qualified gentlemen.

Jan 6, 1953

By J. A. Cordier

USINOR has conducted four blast furnace tests with formcoke made from marginal coals in the pilot plant of HBNPC ("H. B. N." process) in four different blast furnaces of various sizes and with medium and high grade burdens. The tests in which up to 30% of the blast furnace fuel burden was replaced by HBN formcoke yielded good results on furnaces ranging in hearth diameters from 5.6 to 9.5 m. The tests demonstrated that: - the slight increase of pressure drop in the stack did not prevent smooth operation at record production rates with the same blowers - the total coke rate was not significantly affected, but there was a slight increase of the calorific value of the top gas - the hot properties of the formcoke are satisfactory as seen from the samples withdrawn at the tuyeres and tapholes. At the end of the two months test on BE nº 2 of Dunkerque, the hearth was as permeable and clean as with good standard coke. Our conclusion is that HBNPC formcoke made from lean coals is an adequate substitute for conventional coke in the range of 20 to 40% replacement, which is of interest to USINOR.

Jan 1, 1977

By C. S. Giggins, F. S. Pettit

The oxidation of Ni-Cr alloys in 0.1 atm of oxygen has been studied at temperatures between 800" and 1200°C. For alloys with 30 wt pct or more Cr, continuous layers of Cr2O3 are formed during oxidation. In the case of alloys with chromium concentrations between approximately 5 to 30 wt pct, external scales of Cr203 are formed over grain boundaries whereas internal precipitates of Cr2O3 and external layers of NiO are formed at other areas on the alloy surface. When such conditions are present on the alloy surface, chromium diffuses laterally from those areas covered with a continuous layer of Cr2O3 to areas where a Cr2O3 sub scale exists and it is possible for the sub-scale zone to become separated from the alloy by a continuous layer of Cr2O3. Whether such a state will be attained depends upon the initial grain size of the alloy and the oxidation time. When the concentration of chromium in the alloy is less than 5 pct, Cr2O3 is formed internally both at grain boundaries and within the interior of grains and the alloy is covered with an external layer of NiO. MECHANISMS which describe the growth of oxide scales on nickel-base superalloys are complex and the effects produced by the various elements in these alloys on the oxidation behavior of superalloys are not clearly understood. In order to determine the influence of the different elements on the oxidation behavior of superalloys, it is first necessary to examine the oxidation properties of binary nickel-base systems which contain the principal elements present in the superalloys and then progressively more complex systems until compositions typical of the superalloys are attained. Chromium is present in virtually all nickel-base superalloys and the purpose of the present studies was to examine the selective oxidation of chromium in Ni-Cr alloys. The oxidation characteristics of Ni-Cr alloys have been extensively studied1-" to date principally as a result of the high oxidation resistance exhibited by some of these alloys. Ni-20Cr* has long been known *All compositions are given as wcight percent unless specified otherwise. to be oxidation resistant and is commonly used as resistance heating elements for service temperatures up to 1100°C. This alloy cannot be used for extended periods of time at higher temperatures because of the apparent reaction of the external scale with oxygen to form gaseous CrO3. In spite of the considerable work cited above some important aspects of Ni-Cr oxidation still remain unresolved. Virtually all of the previous studies agree that small additions of chromium to nickel, e.g., <10 wt pct Cr, result in increased oxidation rates as compared to that of pure nickel, whereas larger additions, e.g., 20 to 30 wt pct Cr, form alloys with substantially lower oxidation rates. The controversial aspects of the oxidation mechanisms for these alloys that still remain unresolved are as follows: 1) A description of the oxidation mechanism for the low chromium alloys. 2) A description of the oxidation mechanism for the high chromium alloys, particularly with respect to the composition of the external scale which results in the lower oxidation rates. 3) The specific alloy compositions at which the oxidation mechanism changes from that obtained for low chromium contents to that of the high chromium alloys and the reason for this transition. EXPERIMENTAL The Ni-Cr alloys listed in Table I were prepared from high purity metals by nonconsumably arc melting and casting as buttons. These alloys were then given a preliminary annealing treatment in argon at 815°C for 100 hr to promote homogeneity. Each button was cut into 0.250 in. thick sections that were subsequently cold-rolled to 0.050 in. thicknesses and annealed in argon at 815°C for 48 hr to provide a twinned, equi-axed grain structure. The grain size for these alloys was not uniform and the limits, within which the average grain size lies, are given in Table I for the single-phase alloys. All the alloys were single phase with the exception of the Ni4OCr alloy in agreement with the Ni-Cr phase diagram.&apos;&apos; Rectangular specimens were cut from the sheet to provide surface areas of approximately 2.5 sq cm. Exact areas were determined with a micrometer after surface preparation was completed. All of the specimens except the Ni-40Cr alloy and pure chromium were polished through 600-grit Sic abrasive paper, ultrasonically agitated in ethylene trichloride, rinsed with ethyl alcohol, and electro-polished. The specimens were electropolished in a 10 vol pct H2SO4 (conc), 6 vol pct lactic acid, methyl alcohol solution at 70" to 80°C for 2 min at a current density of 0.8 to 1.2 amp per sq cm. This electro-polishing procedure did not produce acceptable surfaces on the Ni-40Cr alloy nor on pure chromium and the oxidation properties of these materials were obtained for specimens polished through 600-grit Sic

Jan 1, 1970

The sudden and untimely death of Dr. Charles R. Van Hise, late&apos; president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people&apos;s university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise&apos;s contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise&apos;s death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definitive life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENTVALUEOFAMINERALPROPERTY In essence the present value of a mineral property is a sum of money in today&apos;s dollars that future earnings from the property are worth. It differs

Jan 1, 1959

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENT VALUE OF A MINERAL PROPERTY In essence the present value of a mineral property is a sum of money in today&apos;s dollars that future earnings from the property are worth. It differs

Jan 1, 1964

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts&apos;2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By Samuel Hoyt

THIS paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use.

Jan 1, 1928

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule&apos;s associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of- concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world&apos;s largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [Chemical Mineral Composition % Mn Hausmannite Mn304 72 Polianite MnO2, 63.1 Pyrolusite MnO24 60-63 Cryptomelane KR8O16R (R=Mn) Variable PsilomelaneBa Mn Mn8O16 (OH).45-60 CoronaditePb R8O16R (R=Mn) Variable Hollandite Ba R8O16R (R=Mn) Variable Manganite Mn2O3•H20 62 Braunite 3 Mn2O3•MnSiO3 62 Tephroite 2 MnO•SiO2 54.3 Rhodochrosite MnCO3 47 Rhodonite MnSiO3 42 Spessartite 3 MnO•AI2O3•3SIO2 33.3 WadHydrous Mn OxidesVariable Franklinite(Fe Mn Zn)O(Fe Mn)sO3 Variable Asbolan Cobaltiferous wad Variable AlabanditeMnS63.14] Geology From a geological standpoint most manganese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, US southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, MT. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1983

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg2SiO4) and fayalite (Fe2SiO4) in solid solution. The name olivine was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Olivine is the principal component of the rock dunite, which itself is a member of the peridotite group of ultrabasic igneous rocks. European uses of the terms olivine and dunite are somewhat different than US usage. In commerce European usage defines dunite as containing 36 to 42% MgO, 36 to 39% SiO2, and loss on ignition of approximately 10%. The term olivine is used to designate a material containing approximately 85% forsterite, with a chemical composition of approximately 45 to 50% MgO, 40 to 43% Si02, 5 to 8% Fe2O3, and ignition loss of 1 to 2%. Uses The principal use of olivine is in various applications involving hot metal. Table I shows the best estimate available as to the amount of olivine consumed by various industries worldwide. In excess of 90% of world uses involve hot metal, with approximately 75% as a slag conditioner in the blast furnace production of pig iron. Approximately 15% of total olivine usage is as a special foundry sand in mold making for the brass, aluminum, magnesium, and manganese steel foundries (Schaller, 1957, 1958; Snyder, 1957; Anon., 1977). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as hand-cobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, has found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). The use of olivine as an additive in the blast furnace is relatively new, having been developed during the last decade. J.W. Currier (Private communication, 1978) describes the behavior of olivine in the blast furnace as follows: Olivine (Mg, Fe2, Si04) represents a unique lime-free source of magnesia and silica as a blast furnace charge component. Only recently has the magnesia-rich mineral been recognized as beneficial cleaner for blast furnace experiencing the problems associated with excessive alkali inputs and/or low coke stabilities. For some time it has been known that alkalis tend to recycle and accumulate in blast furnaces. In the high temperature region of volatilization the elemental alkalis formed attack the integrity of the graphite structure. This alkali attachment is enhanced when poor coke is used. Higher in the furnace stack volatile alkali cyanides condense and oxidize. This accumulation of alkalis tends to agglomerate the burden materials, producing scabs and scaffolds. These structures not only inhibit the downward movement of burden materials and the upward passage of wind, but also lead to erratic furnace performance

Jan 1, 1983

By E. A. Calnan, B. E. Williams

IN the development of a new treatment for the prediction of deformation textures,&apos;-&apos; it was noted that for no metals are there experimentally determined tension textures with which the predictions may be compared. There is a considerable knowledge of drawing textures and previous workers have been content to consider these as equivalent to tension textures for the purposes of comparison. It is shown, however, in the new treatment that the tension and drawing textures are not necessarily identical, the radial compression exerted by the dies in the drawing operation producing some modification of the tension texture. In particular for the face-centered cubic metals it is predicted that for drawing the final texture should be [1ll] with a spread towards [211] (a more detailed derivation of this texture has been made by Calnan3). This has been amply confirmed by experiment, see Hibbard.6 For the pure tension case, however, the treatment predicts intermediate [1ll] and [loo] textures leading to a [211] end-point, while all previous treatments have predicted the final texture as [1ll] with in some cases an additional [loo] component. Thus evidence that the pure tension end-point is the [211], or at least that [1ll] and [l00] are not the final textures, should provide a valuable test of the new treatment. Accordingly some experiments were made on aluminum. Three aluminum specimens were examined in detail, one of cold-rolled high purity rod (99.99 pct), specimen A, and two of commercial extruded rod of purity 99.4 pct, specimens B and C. The initial annealing treatments were: A, 1½ hr at 400°C; B, 2 hr at 400°C; C, 1½ hr at 650°C. The principal difficulty is that of obtaining sufficient elongation before fracture occurs. This was overcome to some extent by giving a softening heat treatment, 1 hr at 300°C, after each 15 pct of extension. Vickers hardness measurements gave values before and after the softening treatment of about 30 and 28, respectively, in comparison with the initial value of about 19 corresponding to fully annealed material. From recent observations in this laboratory it is concluded that this small recovery corresponds to a polygonization process rather than recrystallization proper and consequently the preferred orientation is unaffected. At the higher extensions, however, some slight necking of the specimens took place and it was necessary to turn them down to a uniform cross-section before

Jan 1, 1953

By Dubois Eastman

BEHIND the contrasting liquid-fuel technologies of Germany and the United States lie the basic differences of scarcity and abundance. The chemists and engineers of each nation have developed processes that accommodate available raw materials. In the United States, processing is based on an abundant supply of petroleum, which is refined into a variety of fuels and lubricants. Germany has little indigenous petroleum but has a readily available supply of coal that can be converted into liquid fuels and lubricants. As a result, in Germany several basic processes have been developed for the conversion of coal into synthesis gas (carbon monoxide and hydrogen). In turn, this gas is processed into products. As a normal function of its researches into petroleum processing, the petroleum industry in the United States has made careful studies of various conversion and synthesis techniques. A number of oil companies are carrying out independent development programs with the aim of synthesizing hydro- carbon products that can be marketed at a price that will compete with the price of refined petroleum products. American oil companies hope to perfect synthesis processes that will directly benefit the consumer. A good example of progress in these terms is the synthesis plant at Brownsville, Texas, which is based on the conversion of natural gas to synthetic fuels and other valuable products. When this plant is operated at near capacity, it is expected that the products will be able to compete favorably for the consumer dollar. The complete gasification of coal is a technique well rooted in history. As a controlled process on a small scale, it goes back centuries. As a practical technique on a commercial scale, it dates back to 1839, when "producer gas" appeared in Germany for limited industrial use. By 1873, "water gas," or "city gas" as it is sometimes called, was being manufactured commercially in the United States for use in heaters and stoves. The water-gas process was the cornerstone for modern synthesis. To older methods that were concerned only with carbon and oxygen reactions, it added hydrogen by means of steam. Thus far the goal of conversion was to produce gas for heating, lighting, industrial use, and cooking. The long step forward to synthesis was made in 1927, when Germany started to make gasoline from coal by means of the revolutionary Bergius hydrogenation process. A year earIier, Franz Fischer and Hans Tropsch had announced their process, which finally reached the

Jan 1, 1953

By Sir Robert Hadfield

Table 1 gives the composition of the specimens listed by the author. The details of test procedure and the results of the tests on mechanical, magnetic and electrical properties and cor-rodibility of the alloys are published in full in a paper by the same author, "Alloys of Iron and Manganese Containing Low Carbon," presented before the Iron and Steel Institute (of Great Britain) and published in full in their Proceedings for 1927, to which reference should be made. After reporting these tests the author gives the following discussion of results:] The studies here reported do not indicate that any of the series has really valuable or useful qualities for industrial applications, though the demands of industry are so varied that it is unsafe to prophesy that no special use will be found for a given material. The non-magnetic property of manganese steel is due to the association of Fe and Mn, but carbon has also an effect, enabling non-magnetic qualities to be obtained with a much lower percentage of Mn than would otherwise be the case; for example, 16 per cent. Mn is necessary for alloys practically free from carbon, while with 1 per cent. C nonmagnetic alloys may be obtained with as little as 7 per cent. Mn. Carbon, however, is the prime cause of the development of magnetic qualities by heat treatment. (Sec section 8 of the paper referred to above.) These Fe-Mn alloys show a resistance up to 87 microhms per c. c., but. as there are other alloys which have a resistance as high as 130 microhms per C. c., this does not provide any new feature of value. The most marked feature of the series studied is the brittleness in the range 3 to 10 per cent., with a maximum of brittleness at 7 per cent. Material with this percentage, while possessing quite appreciable hard-

Jan 1, 1927

By Nicholas J. Grant, Michio Yamazaki

Cast copper alloys containing 10, 20, and 30 pct Ni and 0.75 to 0.80 pct Al were machine-milled into chips, then comminuted in a rod mill to fine flake powder utilizing a number of processing variables. The powders here internally oxidized, mostly at 800°C, in a low-pressure oxygen atmosphere. The consolidated powders were hot-extruded into bar stock. Room-tenmperature tension tests, stress-rupture tests mostly at 650°C, but also at 450° and 850°C, and hardness measurements after various annealing temperature treatments to study alloy stability were perfomted. Excellent room-temperature strength, high rupture strength at 650°C, and resistance to recrystallization at 1050°C were obtained. Problems in optimizing conditions for internal oxidation of Cu-Ni base alloys are discussed. THE interesting high-temperature properties of SAP&apos; have stimulated considerable effort in the study of more refractory alloy systems where the potential for high-strength alloys at high temperature is great.2-13 A number of methods have been utilized to produce the desired fine, hard particle dispersions, of which internal oxidation2,9,7 of dilute solid-solution systems offers considerable promise by virtue of the potential for producing ultrafine, well-dispersed oxides. While most of the published works are concerned with pure metal matrices, a number of investigators have studied the effects of solid-solution strengthening.10,19 Use of more complex alloy matrices (for example, aging systems) has been unsuccessful because overaging still occurs at high temperatures in the oxide-containing alloys.14.15 Solid-solution strengthening is, however, effective at very high temperatures9,10 and might be expected to contribute importantly to the strength of oxide-dispersion strengthened alloys. For this study, internal oxidation of solid-solution alloys of copper and nickel, containing small amounts of aluminum, was chosen as the method of alloy preparation. PREPARATION OF ALLOYS Three copper alloys containing about 10, 20, and 30 pct Ni and each containing 0.75 to 0.80 pct A1 (enough to yield about 3.5 vol pct alumina) were prepared as air-cast ingots measuring 2.5 in. diameter by 6 in. high (see Table I for the analyses). Processing steps for all the alloys were as follows (also see Table 11): 1) Homogenization of the ingot at 982°C (1800°F) for 45 hr in an argon atmosphere. 2) Machine milling of ingots into fine chips. Average thickness was about 0.1 to 0.2 mm. 3) Hydrogen reduction of chips at 593°C (1100° F) for 1 hr to reduce copper and nickel oxides. 4) Rod milling of chips to finer powders. 5) Hydrogen treatment of powders as in step 3. 6) Internal oxidation of the powders. 7) Hydrogen treatment of oxidized powders as in step 3. 8) Hydrostatic compression of evacuated powders. 9) Sintering of compacts in hydrogen. 10) Hot extrusion. Variations in processing among the alloys were made in steps 4, 5, and 10 (see Table 11). In the past, two methods were utilized to internally oxidize alloy powders. Preston and Grant3 surface-oxidized dilute Cu-Al powders to obtain the necessary amount of oxygen to oxidize the solute metal (aluminum and silicon), and then permitted the formed copper oxide to diffuse and react with the solute in an argon atmosphere. Bonis and Grant4 exposed Ni-A1 and other nickel alloys to an oxygen pressure derived from the decomposition of nickel oxide at a preselected temperature, in an argon atmosphere. Both methods are applicable and can be modified to generate a range of oxygen pressures for oxidation of the solute but not the solvent metals. Procedure I: Surface Oxidation of Alloy A3, Cu-10Ni-0.76A1. Powders of -20 to +28 mesh were surface-oxidized at 500°C (932°F) to obtain the desired amount of oxygen for oxidation of the aluminum to alumina; the powder was then sealed in Vycor and heated at 900°C (1652°F) for various times up to

Jan 1, 1965

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932

By K. Huessener

Discussion of the paper of K. HUESSENER, presented at the New York. meeting, February, .1916, and printed in Bulletin No. -110, February, 1916, pp. 443 to 474. KARL NIBECKER, Youngstown, O.-It has been contended that the method of measuring the operation of a blast-furnace boiler plant by means of the amount of steam generated per pound of coke used in the blast furnace is not of any value and even that it is quite misleading. It has been found, in the plant with which I am connected, that, in general, a blast furnace will operate during a month so close to average. conditions that the average monthly measure of the plant efficiency is indicated by the number of pounds of steam made per pound of coke put into the furnace, neglecting the amount of iron made and the amount of gas used for heating the stoves. For some time, it has been our custom to keep a record of this figure and use it as a general indicator of the operating practice. In comparing this figure from two different plants we have found some difficulty, due to differing conditions. It is conceivable but not altogether probable that a slight difference in burden, kind of ore or coke, would account for this difference. The method of using the gas, whether washed or unwashed, and the plant arrangement, may affect this number. For several plants on which we have worked up this number, we have found that most of the ordinary running irregularities are eliminated during a run of a month or more and that the number is, therefore, satisfactory. In connection with a plot of the number of pounds of steam generated per pound of coke, we are also plotting the production of the furnaces and the pounds of coke used per ton of production. With these three curves plotted on the same sheet, we believe that the operating man has sufficient information to judge of the efficiency of his plant&apos; for any month.

Jan 5, 1916