Search Documents

By M. H. Pilkuhn, H. Rupprecht

p layers on n-type substrates of GaAs were prepared by difhsion of zinc into these substrates. Experimental details about the diffusion technique will be presented. It will be shown that inhomogeneity in the substrate doping level and crystal shucture defects cause nonplanarity in the junction plane. These nonplanarities give rise to high threshold current densities. From incremental sheet-conductivity measurements the zinc profile is derived. Data about surface concentration and gradient of the zinc concentration at the junction are presented. Finally, some results of laser diodes, which were made of wafers with extremely planar diffusion fronts, are discussed. ThE investigations reported here are part of a program concerned with the materials aspect in the fabrication of GaAs laser diodes. This includes studies of the influence of crystal defects introduced both during the growth of the crystal and as a consequence of subsequent diffusion. Compared with the progress made in the investigation of structure defects, for instance by X-ray microscopy in materials like silicon, no similar results are known so far for the case of GaAs. The further progress in laser diodes will depend very much upon our knowledge of these structure defects and subsequently upon our ability to avoid them. Laser diodes of GaAs had been made mostly by diffusing an acceptor impurity, normally zinc, into an n-type substrate. This procedure was found more convenient than the inverse one for various technical reasons. We will follow this line and restrict ourselves to zinc diffusion only in this paper. DIFFUSION TECHNIQUES AND EXPERIMENTAL DETAIL In order to set a refgrence for our experiments, we used a standard procedure for the diffusion runs. The diffusions were carried out in a sealed quartz tube for 2-1/2 hr at 850°C. One milligram zinc arsenide (ZnAsz) per cu cm of the tube volume served as zinc source. Under these conditions the junction depth was between 25 and 30 p. It is assumed, according to the investigations of the zinc arsenide system by V. Lyons and V. ilvestri,' that ZnAs2 dissociates completely at 850°C into ZnsAsz and Asg. Since there is a condensed phase of ZnsAs2 in the tube at 850°C, the partial pressure of zinc is controlled by the pressure of the arsenic formed by the dissociation of ZnAs2. Due to the fact that the zinc partial pressure resulting from the dissociation of ZnsAsz is only a weak function of the partial pressure of arsenic, the amount of the initial ZnAs2 is not very critical. Experimentally, we found that the junction depth, as well as the surface concentration, was practically the same, if the ingots of ZnAs2 varied between 0.2 and 5.0 mg per cu cm. The wafers were oriented with the main faces in (100). Surface damage due to cutting and lapping was removed by a chemical-etch treatment in a rotating beaker (etch solution: HzSOr, H202, and HzO in a ratio 3:l:l). The GaAs substrate material was n type and doped with tellurium, selenium, silicon, or germanium. It was grown by means of horizontal or Czochralski techniques. After the diffusion process, junction depth and planarity were checked either by grooving with a

Jan 1, 1964

By O. C. Ralston

THE use of copper sulfate for improving the flotation behavior of sphalerite is probably at least 15 years old. The original discovery of its activating influence is somewhat obscure. The story goes that in the mill at Mascot, Tenn., its favorable action was discovered by accident, early in 1914, as follows: The original laboratory test work on a sphalerite ore gave favorable flotation results, but after a mill had been built the flotation concentration of the ore was very unsatisfactory. In diagnosing the probable reasons, one fact pointed out was that the laboratory test machine had been constructed of bronze whereas the commercial machine allowed pulp to come in contact only with wood and iron. A plate of sheet copper was hung in the flotation machine and results immediately improved. At first fanciful explanations of electrolytic and electrostatic behavior were given credence, but when the copper plate was removed and a small amount of copper sulfate substituted in the pulp an even more favorable result was obtained. Toward the end of 1914 copper sulfate was also adopted in the acid flotation circuit of the Butte and Superior Copper Co. Just who is responsible for the original discovery the present writers do not know: It seems strange that in that era of flotation litigation this discovery was not patented. While for pragmatic purposes it may be sufficient to know that the mere addition of copper compounds to a flotation pulp is sufficient to activate the flotation of the sphalerite, for scientific purposes it is quite desirable to know more about how the action takes place. It is the purpose of this paper to present certain evidence dealing with the mechanism of the beneficial effect. The description of the effect as activation in contradistinction to depression is now common in both the English and German languages. It makes no assumptions as to whether the zinc sulfide surfaces have been filmed with copper compounds. In fact, the principal differences of opinion expressed in the literature deal with whether there is an actual formation of CuS (or even Cu2S) on the surface of the sphalerite.

Jan 1, 1929

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

By Charles Berkey

CONTENTS PAGE C. P. Berkey-Responsibilites of the Geologist in Engineering Projects (with discussion) 4 Kirk Bryan-Problems Involved in the Geologic Examination of Sites for Dams 10 0. E. Meinzer-Relation of Ground-water Conditions to Leakage of Reservoirs (with discussion) 19 Charles Terzaghi-Effect of Miner Geologic Details on the Safety of Dams (with discussion) 31 G. H. Matthes-More and Better Geologic Data for Use in Hydraulic Projects (with discussion) 47 L. W. Fisher and R. D. Ohrenschall-Geologic Examination of Dam Sites in the Tennessee and Cumberland River Basins 60 C. K. Wentworth-The Geology of Dam Sites (with discussion) 78 L. C. Glenn-The Geology of Dams and Reservoirs 97 H. T. Stearns-Success and Failure of Reservoirs in Basalt (abstract) 111

Jan 1, 1929

By R. M. Stewart

INTRODUCTION Requirements for achieving economic slope stability in open pit mining must not only be met during the operating stages but in all preceding stages of mine development. In many operating mines little or no emphasis was ever placed on evaluating the stability of possible slopes during the exploration and planning stages. The purpose of this discussion is to emphasize the necessary considerations that should be made in all stages of development in order to achieve the safest and most economic pit slopes. The most economic slopes may not always be the safest slopes and it is incumbent upon the mine operators and engineers to achieve an optimal combination of economics and safety. The stability requirements outlined are based on the profit motive and are, therefore, practically oriented. Long-term basic research or theoretical studies are considered important only to the extent that they can be shown to have a definite payoff. Consideration will first be given to the information required for stability analysis, which can be determined during the exploration and evaluation stage, followed by further stability work necessary during the mine planning and layout stage. Particular emphasis is then placed on the operating stage in which blasting, dewatering, artificial stabilization, and slope failure are discussed. Lastly, the importance of a logical and orderly research procedure is stressed. EXPLORATION AND EVALUATION STAGE The purpose of the exploration and evaluation stage in the mining scheme is to find and delineate a potential orebody. Discovery and delineation commonly involve drilling tens and in many cases hundreds of boreholes. These boreholes, which may cost as much as $20.00 per foot of depth for a cored hole, are usually abandoned once drilling is completed. Stability evaluation for a potential open pit should begin at this stage by taking advantage of the existing boreholes. Rock and soil properties, as well as hydrologic parameters, may be obtained from both the borehole and the core. Seismic velocity and neutron probes may be used to log the borehole to obtain elastic moduli data. A borehole dilation jack may also be used to give backup information on the rock and soil elastic parameters. Use of a core orientation system can result in the determination of fault and joint frequency and distribution. Before splitting or otherwise disturbing the fresh core, qualitative evaluation

Jan 1, 1972

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By J. E. Owen

A model of a porous body is presented in which the pore space consists of a system of voids and interconnecting tubes. Relationships between porosity and resistivity formation factor are determined partly by calculation, partly by experiment. Con triction effects characteristic of the model are shown to be sufficient to account for high formation factors. It is shown that constriction may be combined with moderate amounts of tortuosity to give model pore systems exhibiting to a first approximation porosity and resistivity properties similiar to those of natural porous bodies. INTRODUCTION The relationship between the electric resistivity of a fluid-filled porous body and the geometry of its pore space is so complex that the calculation of the resistivity of a natural porous rock is a practical impossibility. Both the resistivity of a body and its porosity are measurable quantities, however, and previous successes at relating them have been reached by an empirical approach. Efforts at obtaining theoretically derived formulae relating them have generally been unsatisfactory. One of the reasons for this may lie in the pore geometry that has been assumed. THE TORTUOSITY CONCEPT A Parameter called the formation factor is useful in dis-cussing the resistivity of a fluid-filled porous body. This parameter is the ratio of the resistivity of a fluid saturated porous body to the resistivity of the saturating fluid. Formation factors are often available from measurements on cores or from electric logs, and many attempts have been made to correlate formation factors and porosities of geological formations. Whenever a successful correlation is found, the engineer working with electrical logs has a useful tool for the determination of porsities of pay section?. One of the more successful formulae applicable to these correlations is the familiar equation empirically obtained by Archie.' which F is the formation factor. $ is the porosity, and rn is an exponent called the cementation factor. When the for- mula applies, the cementation factor usually is found to be between 1.3 and 2.2. The values for formation factors experimentally obtained are often higher than simple pore geometry would lead one to expect. In an effort to account for such high values certain formulae have been derived based on a so-called "tortuosity concept." In deriving these formulae a synthetic porous body is usually assumed in which the solid material is an electrical non-conductor. and in which the pore system consists of three sets of fluid-filled tubes of uniform diameter connecting opposite faces of the body which, for convenience, is considered to be cubical in shape. The three sets of tubes account for the whole of the effective porosity of the body, and usually, it is specified that they do not interconnect. By considering that the pore tubes are not straight but tortuous, their resistance to the flow of electric currents can be made as high as needed to explain high formation factors. Such an explanation has some basis in fact, but it appears that the tortuosity concept is often incorrectly applied when other factors are largely responsible for observed high resistivities. Recently, Wyllie and Spangler have recognized that tortuosity as calculated by conventional formulae has little if any physical significance.' RESISTIVITY AND THE CONSTRICTION CONCEPT Any explanation of high formation factors which depends solely on tortuosity of uniform pore paths necessarily ignores the effect that variations in the cross-sectional area of the conducting paths have on the resistivity of a body. Although, as previously pointed out, the calculation of such paths for an actual body is impossible, it will he shown that a synthetic pore network can be devised which will yield to analysis, and lead to results in agreement with the experimental data represented by Equation (1). The porous body to be considered is assumed to be homogeneous and isotropic or, for present purposes, identical in its characteristics in the three directions parallel to its coordinate axes. It will he assumed to be built of identical unit cubes, each of which contains a single pore network connecting all faces of the unit cube. A unit of such a pore network is shown

Jan 1, 1952

By Paul K. Krueger

SUMMARY Since 1970 the Federal Preparedness Agency has been using computer models to help establish the amounts of strategic and critical materials to be held in the National Stockpile. Fifty-three of these materials are metals or minerals. The following diagram shows the linkage of models used to estimate material requirements. [ ] The starting point for the models are estimates of the major components of GNP for some future period. These may be estimates purchased from a forecasting service or may be produced in-house. The projections are translated into industrial final demands using DITT (Demand Impact Transformation Tables), a system developed at FPA. Then using a version of the current Bureau of Economic Analysis input-output model, estimates are made of the gross output of each industry necessary to support the level and composition of GNP as specified by the macro-economic model.

Jan 1, 1977

By J. David Lowell

For the first time in several years, Chile is again opening its doors to foreign investment. In its new investment code, the Chilean government has announced its willingness to become a partner in joint Chilean-foreign projects for a number of government-controlled porphyry copper deposits at the developed, semi-developed, or prospect stage; and, that it will allow privately owned deposits or deposits discovered by new exploration to be developed with up to 100% foreign ownership. Three deposits of particular interest are: El Abra, with at least 300 million mt of +100% Cu; Los Pelambres, with at least 428 million mt of 0.78% Cu and 0.03% Mo; and Andacollo, with 350 million mt of 0.70% Cu and 0.015% Mo. (El Abra is almost entirely government- controlled; but both Los Pelambres and Andacollo are mostly under private ownership.)

Jan 11, 1974

By Tribhawan N. Srivastava

The Henderson Mine started production in 1976 utilizing a unique, push-pull, mine ventilation plan. As the mine expands in size, the mine ventilation requirements will increase and a more comprehensive system for maintaining ventilation will be needed. A computer simulation study was completed and has resulted in a revised, systematic, mine ventilation plan which is being implemented as mine development proceeds. Based on the computer simulation study, the new ventilation plan takes into account mining of the orebody simultaneously from both the 8100 and 7700 production levels. Present experience and empirical data indicate that volumes of air needed to adequately ventilate both production levels cannot be obtained utilizing the existing mine layout. The total volume of air needed for the mine excluding haulage tunnel will increase from 708 m3/s (1 500 000 cfm) to 1652 m3/s (3 500 000 cfm), thus a new No. 5 exhaust shaft and connecting drifts are being developed to expand the mine ventilation system to service both production levels. The original ventilation plan for the 7500 haulage level was to bring air from the No. 2 and No. 3 intake shafts and exhaust it through the 94X raise to the 8035 exhaust level and then through the No. 1 exhaust shaft to surface. Control of air volumes in loading drifts was initially planned to be achieved by air doors and air curtains. Air doors on the 7500 level require large cutouts, expensive installations and constant maintenance. The computer simulation study indicates that air- flow in the 7500-level production drifts can be con- trolled exclusively by air curtains which are less expensive to install and more effective in regulating airflows than air doors. Air from the 7500 level can be exhausted through a new raise to the new 7635 exhaust level and then through the new No. 5 exhaust shaft.

Jan 1, 1982

By William G. Pariseau

There are important phenomena in rock and soil mechanics that cannot be explained in terms of theories of homogeneous, isotropic materials. Subsidence of strata about mine openings is an example. In-situ stress measurements in nonisotropic sedimentary and metamorphic rocks is another. Patterns of joints, faults, fractures, and similar geologic features impart directional mechanical properties to rock masses that are locally isotropic or anisotropic. On the geologic scale, the nonhomogeneity of composite rock masses may, in certain instances, be dealt with as homogeneous anisotropy. The mechanics of large rock masses can, therefore, be expected to involve considerations of anisotropy. The source of the anisotropy is not relevant. Once the scale of observation is selected and the material is defined accordingly, the analysis of stress and deformation proceeds without regard to the numerical values of the material constants. There are also important phenomena in rock and soil mechanics that cannot be explained in terms of linear elasticity, theory. For the mechanical description of anisotropic geologic materials capable of deforming beyond the limit of purely elastic strains, a plasticity theory is required. The purpose of this chapter is to present a plasticity theory for anisotropic rocks and soils. The proposed theory is based on the work of Hill in anisotropic metal plasticity and represents an extension of his work so as to include anisotropic geologic materials. The point of departure from metal plasticity theory begins with the inclusion of the normal stresses as linear terms in the yield condition, which plays a central role in plasticity. Once the yield condition is established, the plastic strain increments are obtained immediately through the principle of normality. For practical applications, some simplification of the three-dimensional theory is re-

Jan 1, 1972

By W. J. Whiten

Current developments in one type of crushing and screening model is reviewed and general design techniques and policies are proposed for the control of crushing plants.

Jan 1, 1984

By Whitmell J. Smithwick, Charles E. Dandois

The first operating unit of the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany was rated 185 tpd and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are under construction or on order. Sizes range from approximately 100-330 tpd, however, units of over 500 tons are in the design stage. The ring shaft kiln is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping (Fig. 1). Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc., are mounted at the kiln top and at the bottom of the kiln is the silo with a vibrator type discharger. Mounted separately is the required blower for injector air and fan for internal cooling.

Jan 4, 1973

By Roswell Johnson

To know the rate of decline of oil wells is very important, yet ordinarily we are prevented from getting this rate because the oil from several wells is put into one or a few tanks as soon as the wells have been connected to the power. The object of doing this is economy of tanks, pipes, labor and accounting. FIG. 1. But we are making a great sacrifice for this small economy. The advantages of the individual records are that we would know better: 1. When the well has ceased to be profitable. 2. When a well has gotten into bad condition. 3. The real record of the yield per acre and the rate of decline of the wells. The lease total is too mixed as to age of the wells for existing records to have much significance. To obtain such individual well records and more accurate logs are the great desiderata of satisfactory management of oil properties. 4. Which wells show the slowest decline-information which is valuable in locating new wells or purchasing adjoining leases.

Jan 6, 1917

By Roswell Johnson

THE principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to. a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method.

Jan 6, 1915

By Granville S. Borden

THE program for income tax legislation presented here proposes some diminution in the current tax burden on mineral producers but it will, if enacted, eventually increase the potential and current Government revenue from the mineral industry.

Jan 6, 1951

By Richard E. McElvain

The mining and other industries have grown and changed with- respect to their requirements for slurry pumps capable of handling high percentages of abrasive materials. Greater solids concentration, higher heads and pressures, and increased flow arc not possible. Today's equipment delivers up to three times the flow-tonnage and 1.3 times the head per stage as compared with pumps of ten years ago. This results in four times the requirement in size and energy. The new centrifugal pumps are capable of handling these requirements at pressures up to 4826 kPa (700 psi), with 6895 kPa (1000 psi) or more being considered for future systems. The latest pumps, functioning at four times the operating requirement on flow-head, weight eight times more than the previous equipment. Efficiency is increased slightly, to about 75 % to 85%. A testing program on equivalent units has confirmed that the added strength and specific design of heavy-duty pumps can meet demanding engineering objectives. Operating life on difficult-to-pump materials is increased from 500 to over 5000 hours of continuous operation; the ten-fold increase in pump operating time is a major design objective.

Jan 12, 1976

By Kenneth N. McLeod, Donald W. McGlashan

In the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle.

Mar 1, 1956

By F. P. Haver, M. M. Wong

The Federal Bureau of Mines has developed a leach= electrolysis method for recovering lead from galena (PbS). Flotation concentrate is leached with ferric chloride (FeCl3) solution to obtain lead chloride (PbC12) and elemental sulfur, PbS + 2FeC13 -+ PbC12 + 2FeC12 + Sº. Over 99% of the P~S in the condentrate is converted to PbC12. The leach solution, composed of brine (NaC1) and FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. Very pure PbC12 (>99.9%).is crystallized from the leach filtrate on cool- ing and is subsequently electrolyzed in a fused-salt bath to obtain molten lead metal (>99.9% Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride, and other values, such as Ag, Cu, Zn, and Sº, are recovered by additional treatments of the leach solution and leach residue. This paper discusses results and conditions of the leaching and electrolysis operations.

Jan 1, 1976

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968