Search Documents

J. S. UNGER,*Pittsburgh, Pit., (written discussion?).-From the subject of the paper it is natural to expect that the data presented must be results secured from an open-hearth furnace working under normal conditions, but such is not the case, as the conclusions are based on the results of laboratory tests, which do not approach service conditions. The early basic hearths were made of burnt lime, then followed burnt dolomite, bricks made of calcined dolomite and a 'binder, usually tar, and finally magnesite bricks covered with a layer of sintered magnesite. When this material became scarce, special dolomitic refractories were used. In the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in the resistance to slaking and to corrosive slags. It is well known that neither pure lime nor magnesia has much value as a refractory. By the addition f fluxes, such as silica and iron oxide, lime is rendered inert to slaking in the same way as are the special dolomitic refractories. An example on a large scale is the ordinary basic open-hearth cinder, produced every clay, which does not slake. Pure magnesia, regardless of the lime content, is not any better fitted for a refractory than pure lime. The pure natural varieties, such as Grecian or Washington magnesites, must be burnt with sufficient silica and oxide of iron to produce a satisfactory material. Grain magnesite, either artificial or natural, is, not used in burning in a hearth in the state in which it is received. To make a satisfactory hearth, it must be made more impure by adding about 20 per cent. of basic open-hearth cinder, otherwise it will-not remain in place.

Jan 5, 1919

By C. P. Watson

It is perhaps significant that a few years ago the sessions held here were chiefly occupied with production. In the last two years these sessions have been concerned with production curtailment, unitization and conservation, notwithstanding that production in the United States in 1929 reached a total in excess of 1,000,000,000 barrels. A study of the leading producing units in the United States shows that Oklahoma, Texas and California in 1929 yielded 84 per cent. of the total production from 33.5 per cent. of the total number of producing wells. Production in the United States in 1929 showed an increase of 107,000,000 bbl. over the 1928 figures. This increase in itself perhaps is not enough to have caused the serious situation that is now confronting the industry. However, taking into account the gradual encroachment on the consumption of fuel oil through the greater utilization of natural gas, probably we have reached the point in the United States where prices will determine to a large extent,' in 1930, the amount that will be produced. In the states of Texas, Oklahoma and California, the most significant developmcnt of 1929 has been the desire of operators to reach some agreement to bring production more or less in control with the estimated demand. In November, production in California, particularly in the Santa Fe Springs field, was drastically cut to meet a certain requirement. Similarly, in Texas, the Yates field has been developed and has been producing under an agreement on the part of the operators; and more recently in Oklahoma City, serious efforts have been made to keep produetion in line with consumption. For the year 1930 we can see nothing in sight except drastic curtailment. This is a matter that I am sure is occupying the attention of all the leaders of the industry.

Jan 1, 1930

By Richard J. Gowen

THE FUTURE The environment in which we live appears to change so slowly that most of us are unaware that any change has occurred at all. As the years pass, we notice increasing smog in our cities, new variations in weather, the shifting landscape with changing populations, and subtle but ever present alterations in the quality of life. In considering the future of our environment, we find we must grapple with questions concerning the very future of life as we know it today. Questions of resources, technology, society, governance, and purpose. Let us focus on the future of our environment and, in particular, raise the question of who is responsible for the environment. We know that action, or lack of action, will clearly influence our future environment. It is fashionable to catalog the many short-sightedness of our forefathers in developing the technologies which support the style of living to which we have become accustomed. However, I shall struggle to resist the temptation to list the well known ills of our present environment. Rather, let us concentrate on the future in our consideration of the priority of the multitude of options proposed to relieve our current energy crisis. We have recently witnessed the dramatic effects of air pollution produced by Mount St. Helen's eruptions. In the state of South Dakota, we watched our blue skies turn hazy and felt our eyes sting with the presence of volcanic ash. We were appalled at the dramatic effects on the landscape, crops, transportation, and all aspects of life in communities immediately downwind of the volcanic eruption. But in a few weeks, life had returned to near normal on the earth's surface leaving the volcanic ash in the atmosphere to ultimately

Jan 1, 1983

By Leonard Larson

DURING several years immediately preceding the adoption of wet-charge smelting at McGill, various necessary conditions affecting this procedure, such as plant rearrangement and the metallurgical nature of the concentrate produced at the concentrator, were fully considered. Wet-charge smelting is not altogether novel to the recently reconstructed smelter at McGill. A number of years prior to this improvement, when flotation methods were initiated at the concentrator, large tonnages of wet and (at that time) sticky flotation concentrate were charged directly into the reverberatory furnaces, because of the difficulty in handling the entire tonnage in the roasters. The plant had excess reverberatory units and this surplus furnace capacity was utilized to smelt raw flotation concentrate. During the years 1927 and 1928, a number of actual operating furnace test runs were made to determine in principle the feasibility of wet-smelting operation. Results were encouraging, and in November 1932 the roasting plant was shut down. For some time thereafter the wet feed was delivered directly to the reverberatory side-charging calcine hoppers already in place. Feeding the wet material through the old calcine hoppers and charge holes into the furnace involved considerable labor, but under the conditions existing at that time it was desirable to continue wet smelting even under the handicap of this laborious procedure. The smelting plant during this period was on a curtailed production basis, operating only about 15 days per month. The alternate starting up and shutting down of the roasting plant presented a difficult problem and charging the wet material directly to the furnace entirely eliminated this difficulty. The roasting plant was never operated thereafter. EARLY PROCEDURE Fig. 1 shows the general layout of the smelting plant before the smelter was remodeled. Under this arrangement, all concentrates and fluxes except converter flux were delivered in cars to wooden storage bins, which paralleled the roaster building. The material to be roasted was dis-

Jan 1, 1938

By N. G. W. Cook

At present, tunnels can be driven in rock by either of two essentially different techniques, in one of which rock-breaking is accomplished by drilling and blasting and in the other by mechanical loading. The methods based on these techniques are comparable in terms of the rates at which tunnels may be advanced, although they differ widely in their range of applicability to different types of rock and lengths of tunnel. The method based on drilling and blasting has reached a high degree of development. It is applicable to even the hardest rocks and rates of advance in excess of 50 ft per day (fpd) are attainable. The main disadvantages of this method are that it involves a sequence of operations punctuated by blasting and that it is relatively uncontrolled, resulting in overbreaking the tunnel profile and damage to the surrounding rock. However, its flexibility, mobility, and low capital cost constitute real advantages in many situations, such as those involving short lengths of tunnel or low rates of advance. Tunneling machines based on mechanical breaking of the rock are a more recent development. They offer a continuous and controlled means of tunneling capable of rates of advance in excess of 100 fpd under favorable conditions. However, these machines weigh many tens of tons and consume several hundred horsepower, so that they are costly and lack mobility. At present, their applicability is limited to long tunnels in relatively soft rock where the high rates of advance and tunnel quality can offset their onerous capital cost. Many situations exist in which the superior quality of a machined tunnel and freedom from blasting would be real advantages, but where the rock is either too hard for existing machines or the length of the tunnel does not justify their capital cost: What are the possibilities of developing cheaper, more flexible, and mobile tunneling machines? Most existing tunneling machines fragment all the rock at the tunnel face to facilitate its disposal. If a machine were used to cut only the profile of a tunnel as one of a sequence of operations, it would be required to break

Jan 1, 1970

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.' DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.' Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.'' As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By D. W. Loughridge

INTRODUCTION Raising capital in the 1990s is a timely subject. However, many of us thought why should raising capital in the 1990s prove to be unlike it was in the 19805, the 1970s, the 1%0s, or earlier? There are a lot of creative people in banking and in corporate treasury departments. New tools and techniques are continuing to emerge, many of which are discussed in other papers in this book. While we have new financing tools at our disposal, the underlying issue has not changed. Projects and investments must be judged on their own merits. If they cannot be justified by conventional financial analysis, they should not be built. If they can be justified, it is likely that the financing will be available. The challenges faced in raising capital in this decade will persist to the next. The issues of the 1980s -- currency fluctuation, disruptive merger and acquisition activity, commodity price volatility, political risk, and debt crisis -- will all persist in an increasingly international business environment. I will focus on the financing we have just completed for the Escondida Copper Project in Chile. The Escondida financing is structured along the classic project financing model developed in the late 1970s, but it deals with issues of the 1980s and the 1990s. The financing was intriguing, not just because of the technical issues involved, but also the challenge of reaching an agreement in a large and diverse group. Escondida had the one essential feature that made its financing possible. It was commercially very attractive. It would produce at low cost a commodity (copper concentrates) that direct consumers felt would be in tight supply. The project had the direct support not only of its sponsors, but also its customers, and, very importantly, its host government. The non- recourse financing of Escondida would not have been possible without the support of these parties, and without the robust economics that made this effort worthwhile. The issue was more complicated. Operations in all parts of the world entail some political exposure. This project is in Chile, where there was a constitutional requirement that a plebescite be held when the project would be in its early stages. This plebescite would determine the fate of a 15 year old military dictatorship. The project is copper, a commodity generally deemed to be in surplus. Copper has a history of price volatility (whose price has varied from $.58 to $1.53 per pound over the past two years). It is politically sensitive, not only in Chile, but in the United States, Canada and other developed countries. The project is international, with all the problems of dealing with a variety of currencies, a variety of cultures, and a variety of laws and commercial practices. The project is also large and capital intensive, with a total cost of U.S. $1.1 billion. ESCONDIDA PROJECT Escondida, the largest known copper ore body in the world, was discovered in March of 1981, by Utah International in a joint venture with Getty Oil Company. In 1984, both Utah and Getty were involved in ownership changes, Utah being acquired by BHP. A later restructuring of the ownership of Escondida resulted in BHP, as manager, carrying a 60% interest, Rio Tinto-Zinc Corporation (RTZ) 30%, and a consortium of Japanese companies led by Mitsubishi Corporation with 10%. The Japanese consortium is incorporated as JECO (Japan Escondida Corporation). This ownership structure, which spread ownership around the world, was the first tangible step toward managing both the commercial and political risk associated with the project.

Jan 1, 1990

By T. K. Smith

The comments contained in the discussion of the paper concerning the prediction of fracture gradients are of considerable interest, since the subject is of a very controversial and timely nature. It is regrettable and Fairhurst2 contradicts the author's statement in the third paragraph of Other Applications. These references create significant doubt that Eaton's Eq. 1 predicts fracture pressure during the injection of fluid into old wells. 3. No evidence is presented in this paper to support the author's Conclusions 2 and 3. While an empirical coefficient related to back-calculated field data is correlated with depth (Eaton's Fig. 4), there is no reason to suspect that this coefficient might be the Poisson's ratio of the various formations involved. 4. Until the field data supporting the empirical approach proposed by the author are presented and evaluated, the accuracy claimed in Conclusion 5 is without substantiation. References 1. Geertsma, J.: "Problems of Rock Mechanics in Petroleum Production Engineering", Proc., First Intl. Symposium on Rock Mechanics, Lisbon (1966) 585. 2. Haimson, B. and Fairhurst, C.: "Hydraulic Fracturing in Porous-Permeable Materials", I. Pet Tech. (July, 1969) 811-817. that the comments are those of a critic and do not offer an alternative and better method for the prediction of fracture gradients. Nevertheless, a reply is in order.

Jan 1, 1970

By J. P. Morris

PREVIOUS investigations1,2 have shown that alloying elements in liquid iron influence the thermodynamic activity of sulphur and thereby affect the partition of sulphur between metal and slag in the desulphurization process. For example, the greater efficiency of desulphurization in the blast furnace as compared to the open hearth can be attributed in part to a higher level of sulphur activity in blast-furnace metal due to the higher concentration of carbon and silicon. In the present investigation, a short study was made of the influence of manganese on the activity of sulphur in liquid iron and iron-carbon alloys. In contrast to carbon and silicon, manganese was found to decrease the activity coefficient of sulphur; and in iron-carbon alloys it counteracts to some extent the influence of carbon. However, at manganese concentrations normally present in the blast furnace or open hearth, the effect of manganese is small. Since manganese sulphide has a limited solubility in iron, manganese can act, under certain conditions as a desulphurizing agent. Considerable data on the manganese-sulphur product in carbon-saturated melts were obtained in the investigation and have been included in this report. The experimental procedure was the same as that used in the earlier investigations on the effect of silicon' and carbon' on sulphur activity. Briefly, the method was as follows: The molten alloy, contained in a graphite or sintered alumina crucible, was brought to equilibrium at a constant temperature with a mixture of hydrogen and hydrogen sulphide of constant composition by bubbling the gas through the metal. Samples of' the melt were taken for analysis at regular intervals by suction through a 2 to 3 mm bore silica tube dipped into the metal. The experiments were run in a graphite spiral resistance furnace with melts weighing 50 to 60 g. The gas bubbling tubes were made of sintered alumina and were 5/16 in. OD, 1/16 in. ID, and 24 in. long. Equilibrium was assumed to have been attained when the sulphur content of the liquid metal reached a constant value. During an experiment there was a rapid loss of manganese from the melt by volatilization. To offset this loss, small additions of manganese were made periodically. The rate of manganese addition needed to maintain a constant manganese concentration was determined in preliminary tests. In all of the experiments, deposits of manganese sulphide formed above the melts in a cooler region of the furnace. Apparently, these deposits resulted from a reaction between manganese vapor and hydrogen sulphide in the gas. To prove that manganese sulphide did not volatilize from the melts to a measurable extent, an experiment was run in which helium was bubbled through liquid iron containing both manganese and sulphur. Although manganese volatilized rapidly in this test, there was no appreciable loss of sulphur. Volatilization of manganese sulphide from a melt would have led to an apparent equilibrium condition in which the sulphur content of the metal was lower than the true equilibrium value. The experimental results are shown in the first seven columns of Table I. The data in the last two columns were obtained from the previous work on the effect of carbon' and show what the results would have been in the absence of manganese but with temperature, gas composition, and carbon content of the metal remaining the same. Comparison of the last four columns show that, in the presence of manganese, the sulphur content of the metal increased at equilibrium and the activity coefficient of sulphur decreased. However, the results show that, for manganese concentrations below 3 pct, the effect of manganese is small. The values for activity coefficient of sulphur given in Table I were calculated from the following relations: S (in liquid metal) + H2 (gas) = H2S (gas) [l] K ph2s/?s X %S X phg = 0.00251 [2] where K is the equilibrium constant for the reaction, PH2S and ph2 are the partial pressures of hydrogen sulphide and hydrogen, respectively, and ?s is the activity coefficient of sulphur. The standard state for sulphur was taken to be a 1 pct solution of sulphur in pure iron. The numerical value for K at 1600°C was determined in the earlier work. For the purpose of showing graphically the results of the tests run at 1600°C, the activity coefficients of sulphur were recalculated so as to correspond to a manganese concentration in the metal of 2 pct in each case. In the calculation it was assumed that the increase in sulphur content of the metal at equilibrium caused by the presence of manganese

Jan 1, 1953

By T. MacDONALD

ATHOUGH flotation has been a commercial process for over twenty years, the last two years have witnessed a sudden and phenomenal increase in our knowledge of how to separate minerals heretofore not considered amenable to flotation at all. As remarked by Professor Locke in the January issue. "Either commercial or laboratory flotation is reported on zircon, ilmenite, carnotite, kyanite, scheelite, chromite, fluorite, feldspar, cassiterite, wolframite, barite, and clay. Attractive patents on soap flotation are U. S. Nos. 2,000,656 and 2,040.187. A survey by Ralston in the February E. & M. J. adds many other minerals to this impressive list. The simple but pregnant fact is that any mineral can be coated, directly or indirectly, with a water-repellent coating, and since this is true, it follows that any mineral can be floated. Fundamentally, this is no new discovery, where, for instance, is the mineral that cannot he washed from a pair of dirty hands by means of soap and water, given the absence of refractory greases or oils which would have no proper place in flotation ?

Jan 1, 1937

By F. P. Bullen

Empirical relationships between fracture stress, orientation angle, and diameter of crystal have been determined at 77°K. Orientation ranges of markedly different behavior were found—a law of constant normal stress&apos; of value a (diameter)-1/2 for the fracture of ductile crystals, and a condition of shear stress (or strain) for more brittle crystals. The observations are not consistent with current theories. An interpretation is advanced which is also applicable to observations on the effect of prestrain at room temperature on the subsequent fracture stress at 77°K and to the effect of cyclic stressing on the cleavage strength.&apos;&apos; The law of constunt normal stress&apos; and the brittle ductile transition are also explained. The interpretation is more consistent with the initiation of cracks by intersecting dislocations than with theories based on stress -concentration by dislocation arrays. ZINC single crystals are particularly suited to the study of cleavage because fracture occurs on the basal plane over a wide range of crystal orientations. Analysis of the conditions of stress and strain at fracture in crystals of different orientations should indicate which parameters control the cleavage process. Unfortunately, controversy has arisen over the correct empirical relationship between tensile fracture stress and orientation. Schmid&apos;s observations1,2 favored a &apos;law of constant normal stress&apos;, as observed in other materials.2 For zinc, however, the observed values are far below the theoretical strength and cannot represent the true limit of cohesion between neighboring atomic planes. Hence, the interpretation of such a &apos;law&apos; is not straightforward. Deruyttere and Greenough3,4 found a complex variation between tensile fracture stress and orientation; this variation did not agree with a &apos;law of constant normal stress&apos;. Two theories have been advanced to account for their observations: a) the propagation of cracks from low-angle boundaries,5 and b) the release of energy from piled-up dislocations during crack-propagation.4 The present work resolves the apparent discrepancy between the observations and shows that neither of the above theories are applicable to the tensile fracture of zinc single crystals. A phenomenological explanation, along the lines suggested by Gilman,&apos; is advanced and successfully applied to previously unexplained effects. EXPERIMENTAL DETAILS &apos;Crown Special&apos; redistilled zinc was used, except for one comparison series op tests using &apos;Tadanac&apos; electrolytic zinc. Crystals of 1 mm diam, subsequently called &apos;1 mm crystals&apos;, were grown from the melt in vacuo in precision-bore Pyrex tubes internally coated with graphite. Several specimens 1 in. long were cut from each crystal and chemically polished. Jigs were used to minimize handling strains, and crystals were mounted in the Polanyi machine the day prior to testing to allow recovery from any such strains. One-mm crystals were chemically polished for long periods to obtain 0.1 mm (approx) crystals. One-mm crystals were cemented into miniature gimbals by &apos;Araldite&apos; casting resin. The Appendix gives the reasons for using gimbals and the results obtained by other methods. More complete details of all techniques are given elsewhere.7 The symbols and terminology used are as follows: X = orientation angle (angle between tensile axis and line of greatest slope in the basal plane). T = tensile stress (on true cross-section) S,N = shear and normal stress (components of T with respect to the basal plane) ? = shear strain D = crystal diameter. The subscript &apos;f&apos; will be used to denote values at fracture. PART I-ANNEALED CRYSTALS EXPERIMENTAL OBSERVATIONS One-mm crystals were used to establish the variation of fracture stress at 77°K with orientation at fracture (Xf), Fig. 1. For 18 deg = Xf = 55 deg, a &apos;law of constant normal stress&apos; was observed. For Xf > 55 deg, the fracture condition approximated to a constant shear stress. At Xf< 18 deg, twinning occurred before fracture so that the results were not typical of homogeneous single crystals,4,8— such specimens will not be considered herein. The dependences of fracture stress upon Xf were of similar type for 6 mm,* 1 mm, and 0.1 mm crystals,

Jan 1, 1963

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

OF THE many categories into which scientific knowledge has been arbitrarily divided, the one which has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. To one who has had no such course or whose auld acquaintance with the subject has all but been forgot, such application is all too often thwarted by the abstruse presentations of the subject found in many of the available textbooks. AS a tool for the control of a complex process involving many chemical reactions, physical chemistry can become very valuable. The specialist who is using this tool for many purposes and perhaps contributing to its development will want to know a great deal more about it than can be included in this book. He will be interested in its history, its accomplishments and limitations, and its applications to many and varied problems. To the steelmaker or metallurgist, however, it is only one of a number of tools that he must use. He is willing to forego the detailed study of its inner workings in order to concentrate upon the development of skill in its application. It is the purpose of this chapter to present a simplified view of physical chemistry as a tool of great potential usefulness. This purpose and the desire for brevity have required the elimination of many of the gadgets with which the tool is usually adorned. It is hoped that this simplification will be conducive to clear understanding. The beginner is urged not to overlook the more extended treatments of the standard textbooks.* He is assured at the same time that the basic tool is sound and serviceable and is guaranteed to give satisfaction if regularly lubricated with common sense. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly

Jan 1, 1944

By M. R. Geer, H. F. Yancey

With the exception of pneumatic processes and a few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral-dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficia-tion process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and elsewhere, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment lor many years, and more recently driers employing centrifugal force have gained in popularity.&apos; A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal—a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. Object and Scope of Investigation Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it On coal &apos;lurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1949

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. CHARLES KIRCHHOFF NEW YORK, N. Y. (Term expires February, 1912.) VICE-PRESIDENTS OF THE COUNCIL. BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Feb 1, 1912

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford&apos; which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.&apos; They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes&apos; made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. JAMES F. KEMP : NEW YORK, N. Y. (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, CAL. W. A. LATHROP PHILADELPHIA, PA. GARDNER F. WILLIAMS WASHINGTON, D. C. (Term expires February, 1913.) KARL EILERS NEW YORK, N. Y. WALDEMAR LINDGREN WASHINGTON, D. C. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Apr 1, 1912

By AIME AIME

Council. * PRESIDENT OF THE COUNCIL. JAMES F. KEMP NEW YORK, N.Y. (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, CAL. W. A. LATHROP PHILADELPHIA, PA. GARDNER F. WILLIAMS WASHINGTON, D. C. (Term expires February, 1913.) KARL EILERS NEW YORK, N. Y. WALDEMAR LINDGREN WASHINGTON, D. C. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Mar 1, 1912

By AIME AIME

COUNCIL PRESIDENT OF THE COUNCIL. CHARLES KIRCHHOFF NEW YORK, N. Y. (Term expires February, 1912.) VICE-PRESIDENTS OF THE COUNCIL. BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.) S. B. CHRISTY BERKELEY, CAL. W. A. LATHROP PHILADELPHIA, PA. GARDNER F. WILLIAMS WASHINGTON, D. C. (Term expires February, 1913.)

Oct 1, 1911