Search Documents

By AIME AIME

A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the temporary use of members of the Institute or of sister societies, or visitors suitably accredited. .In addition to this general accommodation, another room has been similarly furnished as a business headquarters for a single person, and for a limited period. For the conditions of this privilege, inquiry should be made at the office of the Institute. . In order that the benefit of this arrangement shall not be restricted to a few members only, the period of continued occupancy will be limited, and applications will be considered in the order of their receipt. A small. fee will be required for the use of the facilities furnished. ANNOUNCEMENT. THE BIRMINGHAM MEETING. - The XCIVth Meeting of the Institute for the reading and discussion of professional papers will be held at Birmingham, Ala., beginning about October 1. After the Birmingham sessions and excursions, it is proposed to return by special train via Chattanooga, Ducktown, etc., to Washington, D. C., where additional sessions will be held. Further particulars will be given in a special circular, to be issued at an early day.

Jan 5, 1908

By E. C. Herkenhoff

THIS subject may be controversial. Personal preferences influence the final selection of cyclones, and side issues such as costs, floor areas, head room, and ease of replacing worn parts all enter the picture, but the following comments and data should apply to most cyclone selection problems. Broadly, the uses for cyclones in wet classification may be divided into three fields: 1) Open circuit operation, for two products, in which feed rate and sizing vary and the products vary. For example, feed may be divided into a sand product and a slime product. 2) Open circuit operation, for two products, in which feed varies, one product to have constant sizing. This calls for adjustment in either the apex or the vortex aperture. 3) Closed circuit operation, the finished product to have constant sizing. Most classification jobs fall in this category.

Jan 8, 1957

By G. Mempel, D. C. Yang, D. W. Fuerstenau

This paper describes details of the design and operation of a batch tumbling mill which has been used for a number of years in the laboratories at the University of California. In order that the energy expended for grinding can be measured accurately, this specially constructed laboratory mill has sensitive torque measuring apparatus. Torque measurements are given for a variety of conditions with this particular mill. In recent years, there have been numerous and fairly extensive investigations of grinding in tumbling mills reported in the literature. Most of these investigations have been carried out in mills with widely differing dimensions. As a result, comparison of results obtained from various investigations has been virtually impossible. If similar mills were used by different investigators, a considerable step forward would be taken in grinding research. A specially constructed laboratory mill with sensitive torque measuring apparatus has been used for a number of years in the laboratories of the University of California. The purpose of this paper is to describe details of the design and operation of this batch tumbling mill so that other researchers, who might be interested in obtaining data for intercomparison, could construct a similar device for their own research. Furthermore, since torque instrumentation is quite expensive, torque measurements are given for a variety of conditions with this particular mill so that those who may not wish to duplicate torque measuring apparatus can make reasonably accurate torque estimates merely by duplicating the loading conditions. It is not intended in this paper to present theoretical derivations of energy consumption in ball mills. This has been done e1sewhere.l-3 CONSTRUCTION OF THE MILL In order to eliminate rust problems with wet grinding, the mill and grinding media are made of stainless steel. The mill shell was rolled from 1/2-in. steel plate. The inside dimensions are 10-in. diam and 11-1/2-in. length, similar to the mill used by Charles.4 It is equipped with eight lifter bars (1/4-in. in height) whose dimensions are given in Fig. 1. The lifter bars have been bolted into the shell so they can be removed for experiments without lifter bars; however, all data presented here are for the mill with lifters. One end of the mill is fitted with two 1/2-in. diam removable plugs for filling the mill with liquid for wet grinding experiments. The mill is mounted on ball bearing rollers as can be seen in Fig. 2. The pillow block bearings are single-row self-aligning sealed ball bearings with 1-1/4 in. hole diam. The bearings supporting the mill shell are single row sealed ball bearings with

Jan 1, 1968

By G. T. Lineberry

Power requirements for a piece of mobile mining equipment are largely dependent on the set of conditions in which they must operate. These conditions are isolated and key parameters are identified. The effect of operating conditions on power determination is investigated. A simulation technique is developed to predict ranges of power demands for off-highway haul units as an archetype, permitting the analysis of changeable operating conditions. This program uses given data, conditions, and probabilities and ranges to solve for individual components of power, which can then be summed. By adopting such a technique, a systematic and rational determination of power is made possible. The usefulness of this basic approach in the determination of power requirements for other mobile mining equipment is emphasized.

Jan 1, 1983

By Herbert Haas

GEORGE W. HAWKINS, Tucson, Ariz. (communication to the Secretary*).-The paper by Mr. Haas will no doubt be followed with considerable interest, as it covers the power-plant problem in quite a comprehensive way, including not only the usual operating costs but also the fixed charges on the investment, and for load factors ranging all the way from 25 to 100 per cent. and fuel oil ranging from $1.25 to $2 per barrel. The very fact, however, that his paper does cover such a wide range of conditions, makes it the more imperative that any conclusion drawn from his analysis be very carefully considered for any specific case, for in making such analysis the type of prime mover and size must be selected for some one condition which might not be the proper selection had some other condition been assumed as the basic one, resulting in an unfavorable comparison under all conditions except that condition assumed. From the reasons given by the author for his selection of the large turbine units, it is evident he had in mind very high load factors, ranging

Jan 12, 1916

Following the usual custom, three meetings are planned for the year. The Mid-Continent meeting will be held at Oklahoma City, Okla., Oct. 7 and 8, and the California meeting is planned for Los Angeles, probably also early in October. A program along the usual lines is under way for the annual New York meeting. Discussion and planning of the year's activity started in March. An effort is under way to secure papers dealing with some overlapping phases of engineering, petroleum geology, geophysics, law, economics, refining, etc. The main reason for attempting a program along these lines is the belief that unusually interesting technical papers can be obtained. The degree of specialization in the technical and related fields has permitted but few individuals to develop a sufficiently comprehensive viewpoint. Also, at times the developments in a particular field are capable of giving great stimulus toward much needed solutions of difficult problems in others fields of activity. With the coming of the period of restriction of production to market demand, many changes have occurred in policy and technique of petroleum production. Some changes have been advances, others have been of retrograde nature. It seems doubtful whether the adjustment to the condition of excess producing capacity has been complete or sound in some major respects. Many changes are in progress and others need to be initiated. The industry has excessive producing capacity so far as immediate market demand is concerned, but reserves for several years hence are generally believed insufficient. Exploration and discovery should go forward but development should proceed with caution and under control. Property rights should be clarified and protected for the new condition— without excessive cost for drilling wells that serve no purpose except that of giving some protection to property rights at the cost of an increased price to the consumer. Under the more steady condition of assured supply for the immediate future, as compared to the hand-to-mouth condition of wide-open production, a greatly advanced technique of development and production is possible and is being developed. Great progress has been made, but much remains to be done. Along some important lines progress can be effected only by better understanding between the engineer and the geologist, the lawyer, the politician, the geophysicist, etc. There is need

Jan 1, 1937

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute] . METAL MINING TECHNICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 .The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61. Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. 0. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York

Jan 1, 1928

By R. L. Slobod, H. A. Blum

A semiquantitative method for measuring the wettability of reservoir rocks has been developed. These data are needed for reservoir analysis and for interpretation of laboratory displacement studies. The wettability of a core sample is measured by the contact angle for the system oil-water-solid. These contact angles are calculated from the displacement pressure (threshold pressure) obtained by use of the centrifuge, using first oil-water and second air-oil in the same core sample. This method is based on the assumption that the air-oil and oil-water interfaces occupy similar positions in the porous medium when desaturation of the wetting phase is initiated. The assumption is also made that the Contact angle for the air-oil-solid system which is close to zero in value does not change appreciably even when the contact angle for the oil-water-solid system experiences marked changes. "Apparent contact angles'' for five different solids ranging from 31" to 82" have been determined, and changes irr the "apparent contact angle" of a given sample with laboratory use from 33" to 53' {lave been observed. INTRODUCTION Reservoir rocks vary in their wettability, 1,2,3,4 some being preferentially water wet while other are apparently preferentially oil wet. The degree of wettability, in theory, is measured quantitatively by the contact angle for the system solid-oil-water, hut in 1)practice this quantity is extremely difficult to determine." The need for obtaining some measure of this quantity has become obvious in recent years as a result of both laboratory. and field observations. Several reservoir.: such as the Bradford Sand in Pennsylvania and the Wilcox' at Oklahoma City are reported to be oil wet. If these report:: correctly reflect the true nature of the surface of the rock in the ground, then these reservoirs probably will not perform as predicted on the basis of a water wet rock. In the laboratory many core samples have been Observed to be oil wet. These samples, while perhaps not correctly representing the reservoir, have markedly different properties from water wet rock. The location of the phases is different (oil is in contact with rock instead of water), and other quantities such as the connate water, the capillary pressure curve; residual oil. relative permeabilities. and the recovery of oil by water flooding are markedly affected by the value of the contact -4 A further complication observed in the laboratory is the chang-ing of the wettability of a rock specimen with use. such changes mean that repeat runs on the same core are not the duplicate tests desired, but represent new experiments on a more oil wet material. The changes in surface characteristics are sometimes so rapid that by the time an experiment requiring several days is completed, the results may not be representative of the core as originally described, The, rock material itself (Silica. carbonates. etc.), whell Clean and uncontaminated, is water wet. There seems b( : little evidence of the presence of oil wet minerals such as heavy metal sulfides. The oil wetness of reservoir samples, therefore, is believed to be caused by the accumulation of an adsorbed film in which the polar group of a large organic. molecule is adsorbed on the surface leaving the organic or hydrocarbon part of the molecule projecting out from the solid. Such a surface is much more readily wet 17" oil than by water. These considerations indicate the need for a method which will provide some measure of tile wettalbility (Contact(angle if possible) for reservoir rock ..samples) The method should be capable of (1.1 distinguishing between tile wettalility of dif. ferent formation,.. (2) detecting (change. ill wettalbility of a core with use. and (3) measuring the changes in Wettability which may be accomplished with cleaning operations. such as the use of sodium silicate for increasing water wrettalbility." A preliminary report on such a method is preseted below. not with the idea that this procedure alone will Solve the wettabil-ity problem. but rather that it may provide encouragement to

Jan 1, 1952

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By W. S. Stahmann, F. W. Bowdish

Previously published experimental data showing that both collectable and non-collectable sulfide films may be formed on chrysocolla were analysed, and chemical mechanisms were proposed for the formation of the films. A special technique was developed by which the quantity of sulfur adsorbed was determined for samples sulfidized under different conditions of pH and soluble sulfide concentration. The data on sulfur adsorption were used together with the expression for the equilibrium constant for the proposed reaction to indicate the validity of the chemical mechanism theory. A recent paper 1 about contact angle studies on chrysocolla reported the effects of pH value and sodium sulfide concentration during sulfidization upon the character of the surfaces produced. In each experiment the surface of a specimen of chrysocolla was prepared by grinding it with fine abrasive and washing it in tap water. The specimen was then placed in the sulfidizing solution for 10 min, rinsed in tap water, treated for 15 min in a solution containing 30 mg of potassium amyl xanthate per liter, rinsed in distilled water, and tested for air adhesion in a contact angle apparatus. The results, when plotted as in Fig. 1, showed an island representing conditions giving air adherent or collectable surfaces surrounded by conditions giving non-collectable surfaces. Particular interest may be attached to the region of non-collectability to the right of and above the island in Fig. 1, and to the boundry curve separating these two regions. It is apparent that at any pH from 4.0 to 6.0, where a collectable surface may be produced, a sufficient increase in the sulfide concentration results in a non-collectable surface. Thus it appears that too much soluble sulfide has a depressing effect upon the mineral, just as it has in sulfide flotation. This paper presents some speculations regarding the chemical mechanisms by which the collectable and non-collectable sulfide films may be formed and reports on a physical-chemical study intended to support these speculations. THEORETICAL CONSIDERATIONS The experimental results presented in the previous paper were analysed in several ways in an attempt to understand better the chemical mechanisms involved. For several points on the boundary to the right of the region of contact in Fig. 1, molar concentrations of H+, OH-, HS-, and S= ions, as well as various ion concentration products, were calculated. Following the reasoning of Wark and Cox, 2,3 no single kind of ions may be credited with causing depression of the surface because none of them have a constant con-

Jan 1, 1968

By Gunnar Thaning, Goran Mathisson

The iron ores mined by LKAB in the north of Sweden have excellent beneficiation properties. This gives LKAB a favorable position as regards the production of low silica pellets for direct reduction. LKAB has concentrated on developing and marketing grades of pellets for the Midrex-Purofer-HyL process group, i. e., such direct reduction processes carried out in a shaft furnace or a static bed using reformed natural gas as a reducing agent. The paper deals with properties and quality demands of iron ore pellets for such processes. Matters such as the effect of the residual magnetite in the fired pellets on the degree of metallization, the amount and composition of the slag phase in the pellets, the mechanism of the disintegration during reduction, the state of swelling of the pellets during the conditions prevailing in these processes, the importance of the porosity, the improvement of the reducibility and lowering of the sticking tendency of the pellets by small additions of suitable additives, and the influence of the pellet size are discussed. A special test procedure for direct reduction pellets has been elaborated by LKAB. Thus, three metallurgical properties are routinely determined separately, namely reducibility, reduction strength, and sticking. The test methods are described. Finally the present and future LKAB pellets for direct reduction are presented with respect to chemical analyses and metallurgical properties.

Jan 1, 1980

By W. Fletcher, R. C. Schenk

This paper outlines a well proven and highly successful approach for eliminating many of the problem and frustrations often experienced in plant startup. The approach was developed over a period of 25 years during which some 90 plants were commissioned. This paper discusses startup from the contractor’s perspective and highlights the requirement for detailed startup planning, careful coordination during the project final construction phase, and thorough checkout of equipment prior to introduction of feed. Performance of these services has demonstrated a valuable opportunity exists for the contractor to assist in the training of the plant operating personnel.

Jan 1, 1983

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By E. P. Mathewson

(Butte Meeting, August, 1913.) IN a discussion -of a paper on " The Basic Process as Applied to Copper Smelting," by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1S91,1 Prof. W. C. Roberts Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Marshes process would afford anything like the service which it had been shown to render in the metallurgy, of iron. Claude Vautin stated that he had experimented for over two years with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned, Herman Keller, Superintendent of the Parrott smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were -too small. A short time; afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., said at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines.

Jan 6, 1913

By O. Jay Myers

THE war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for cores and mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from 0.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content varies between 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. PROTECTIVE AGENTS In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H20 -+ H21 + MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed `burns'). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the castings unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beck. A possible explanation may lie in the following equation: 2Mg + 02 -s 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945

By C. T. Bischoff

DURING the past few years geochemical testing for traces of heavy metals in water, soil, rock, and vegetation has aroused increasing interest. Various techniques for field and laboratory determinations have been described in the literature, as have some of the results of application. However, little information has been published regarding application to glacial terrain. Over 90 pct of the Canadian Shield is overburdened, resulting in high costs for mineral exploration once the outcropping ore deposits have been found. This has been largely responsible for the widespread application of mining geophysics in Canada, permitting concentration of effort on area or zones considered most favorable. However, geophysical interpretation has its limitations, since at least 90 pct of the structures indicated thereby contain no valuable minerals. A more direct approach is therefore highly desirable. If underlying base metal mineralization can be detected by sampling soil or vegetation at moderate cost this should prove of great help in locating new discoveries or extending known ones. A large proportion of Canadian ore deposits contain appreciable copper or zinc, even where these are not the principal economic metals. Consequently the field of application is a broad one.

Jan 1, 1954

By C. M. Fellman

AVAILABLE data for the first nine months of the Year indicate that accident occurrence in metal mining was well on its way to an all-time low for 1939. However, the relatively rapid pickup in mining production in the fall will be likely to boost both accident occurrence and also accident rates. Results of the National Safety Competition for 1938, the fourteenth of its kind conducted by the U. S. Bureau of Mines, were published in August, 1939. W. W. Adams, statistician of the bureau, states that "with 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost- time accidents occurred during the con- test year." The National Safety Competition provides a means whereby mines and quarries may engage in active competition to stimulate their safety programs. Companies in the contest can compare their records with those of similar plants operating elsewhere and thereby determine to what extent their safety programs are successful. The Joseph A. Holmes Safety Association gave over 150 awards for safety performance in the mineral industries in 1939 and a remarkable phase of these awards was the considerable number given to individual miners who had worked fifty or more years without sustaining a lost-time accident.

Jan 1, 1940

By Louis P. Gignac

INTRODUCTION The selection of trackless equipment for underground mining can be a complex engineering problem due to the wide range of equipment sizes and operating modes. Computer simulation is particularly useful in estimating the performance of different systems for specific rock- handling problems. A hybrid simulator, incorporating some of the features of deterministic and stochastic simulation, was developed in order to handle not only queuing delays at loading and dumping points, but a1 so traffic interferences. Any number of vehicles can operate in any one of four basic modes (LHD, LAF, FEL, HFC) in parallel or in series. If the units use common roadways, loading and dumping points, certain operating delays will occur and be registered by the simulator and thus give a better evaluation of the marginal productivity of each additional unit. Based on a typical layout of drawpoints and ore passes for the sub-level stoping method, productivity and operating costs of different rock-handling systems will be examined. 1 . COMPUTER SIMULATION Numerous applications of computer simulations are reported in the 1iterature for various mining problems. Depending on the complexity of the system to be studied, simulation models were conceived with different degrees of sophistication. Three different types of simulators are generally recognized: stochastic, deterministic, and hybrid. Stochastic or Monte Carl o simulation randomly generates items, transactions, or events from some population defined by a frequency distribution and produces some expected future situations. Because this type of simulation is governed by the input of probability distributions, it requires a detailed knowledge of the system to be simulated; it implies expensive and time-consuming studies and reports to gene- rate this input information. A major short- coming of stochastic techniques is in new equipment evaluation, where the lack of data is unavoidable, and in new system design where the conditions are outside the range of the known historical behavior of the equipment. However, probabilistic simulation is almost essential for the study of cyclic queues and traffic problems. Deterministic simulation studies a system by generating performances on the basis of the mechanical capabilities of the vehicles and the physical limitations of the mining scheme. It is based on the engineering principle that the engine converts its energy into a rimpull at the wheels, which is in turn opposed by the rolling resistance and the grade of the ground; the machine is accelerated or decelerated until the tractive and resistive forces are in equilibrium, at which point it moves at constant speed. The information required by this technique, such as rimpull charts and equipment weight, is readily available from equipment suppliers. However, equipment performance at the mining site is also dictated by human and environmental conditions and changes with time and usage. For this reason, deterministic simulation generally overestimates the system capabilities; these must then be adjusted by efficiency factors based on observation and experience. Recently, hybrid simulation models, using both stochastic and deterministic techniques, have been built with some of the events generated stochasticly and others being deterministic. This compromising approach originated at the Pennsylvania State University. O'Nei1 (1966) designed a simulator for truck-and- shovel operations that allows for transportation from multiple faces to mu1tiple destinations. Each truck performs according to its mechanical capabilities while its loading and dumping time and its load fluctuate according to specific probability distributions. A major advance in the simulation of mining systems is due to Sanford's model (1969) of underground coal mining operations. The originality of the model is in the use of an Executive System Control which sets up the initial system, de- fines the operation conditions , and instructs continuously four sub-assemblies representing shuttle cars, trains, continuous miners , and conveyors, which in turn generate a feed-back of their movement to the Executive Control System for further instructions. The model has enough flexibility to simulate simultaneous and sequential jobs that characterize any dynamic system. Sanford's early work evolved slowly to what is known today as the Under- ground Materials Handling Simulator for coal mining (Manula, 1974).

Jan 1, 1981

By William B. Plank

PRESENT enrollment of 182,361 students in the engineering schools of the United States and Canada represents an increase of 6.6 pct over the enrollment in these schools in 1951-52. Thus is brought to a halt the steady decrease in engineering enrollment that began with the close of the 1947-48 academic year, five years ago. The mineral engineering student picture is similarly encouraging. In the United States schools, 9453 students are preparing themselves for positions in the Mineral Industry. This is an increase of 8.3 pct over last year as compared with an increase of 6.6 pct in the total United States engineering enrollment. The rate of recovery for the mineral engineering group is thus more rapid than for the engineers as a whole.

Jan 4, 1953