Search Documents

By C. A. Hartnagel

In 1939 the production of crude oil in New York totaled 5,105,000 bbl. This marks the third consecutive year production of crude oil has exceeded 5,000,000 bbl. and only once has this total been surpassed—in the year 1882, three years after the discovery of oil in Allegany County, when the annual production was more than 6,000,000 barrels. The most gratifying feature of the industry was the increased demand for lubricants, which resulted in advanced prices for crude. From a price at the beginning of the year of $1.68 per barrel, six advances totaling 82c brought the year's closing to $2.50 per barrel. A further increase in price on Jan. 1, 1940, to $2.75 per barrel places the local industry in a strong position for the year's operations. Most of the oil production of the state is now obtained by water-flooding, and the industry is practically stabilized. No new pools have been discovered in over 25 years, and border drilling indicates little prospect of extending the boundaries of the fields beyond their present limits. Deep drilling to the Oriskany sandstone in and close to the present oil fields hay failed to find oil in substantial amounts. Altogether, the oil pools of New York have produced during the 60 years that they have been exploited approximately 125,000,000 bbl. of oil. Following the flush production of 1882, the annual production gradually dccrcased and the year 1912 marked an all-time low of only 782,000 bbl. In 1919, as a result of flooding operations, a definite upward trend in oil production was recorded. During that year also the production of oil by water-flooding methods as approved by Legislative action. In the 21-yr. period beginning with 1919, oil production in the state ha.: totaled 60,338,000 bbl. Thus it will be seen that by the aid of flooding methods nearly as much oil has been produced in the last 21 yr. as in the preceding 40 yr., although the Iatter period included the flush production in 1882. As there is little hope of extending the area of the present producing oil fields of the state, producers and refiners are concerned regarding the future life of the fields. It is encouraging to observe that earlier esti- Published by permission of Director of New York State Museum, Albany, N. P. Summarized at meeting; manuscript received at the office of the Institute March 20. 1940.

Jan 1, 1940

By Junnosuke Yamamoto

Substituting sodium hydroxide for sodium carbonate as a binder in a glass batch yields harder pellets with a lower melting point. This paper explores the degree of NaOH substitution that is feasible, and compares pellet hardness, and amount of dusting with the degree of NaOH substitution. The effects of the the amount of soluble silicate in the pellet and residual hydroxide concentration in the pellet on pellet hardness are also studied.

Jan 1, 1977

By P. BOURY

THIS account of a contrivance which has been found serviceable in practice may be of interest to engineers, and' especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects, namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle. This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Sep 1, 1906

By George W. Becker, Blair R. Benner, Ronald J. Roman

A computer model for the leaching of oxide copper heaps is developed and verified in laboratory tests. The model can be used to scale-up laboratory test data and to simulate the results of various operating philosophies on heap leaching. The model is applicable to leaching processes where the rate of leaching is controlled by a deficiency of reactant or diffusion of a reactant through the leached rock. Several examples are presented showing the sensitivity of the recovery vs. time curve to the variables in leaching.

Jan 1, 1975

By David H. Carlson, John H. Johnson

The paper presents background information, a description of mine characteristics that affect air monitoring techniques, and a review of Portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the experimental mine, the diesel dilution tunnel test cell, the mine air monitoring lab (MAML), portable instruments, and the production mines used.

Jan 1, 1982

By M. Gangal, B. Paul

It may be seen from Maurer's survey (Maurer,l 1966) that most of the common methods used in rock drilling today depend upon mechanical loading of the rock. In order to predict the behavior of rock under an imposed system of stresses, it is necessary to have a valid criterion which delineates those combinations of stress which cause macroscopic rock failure from those which do not. Admittedly, the conditions under which brittle materials fracture depend very much upon statistically variable local effects such as inclusions, grain boundaries, minute imperfections, etc. However, it is extremely desirable to be able to predict fracture under complex states of stress by means of a stress-criterion of failure, where, for a given material, the effects of the other variables mentioned are incorporated into a small number of experimentally observable parameters. One of the most successful of these "macroscopic stress criteria" has been the Coulomb-Mohr theory 2,3 (also see Jaeger 4 and Terzaghi 5), modified by the addition of tension cutoffs (Paul 6). At first thought it might seem rather odd that a macroscopic theory is capable of predicting fractures which originate at highly localized random imperfections at an atomic level (or more likely at the level of individual mineral grains in rocks). However, Griffith7 showed that fractures originating near the tips of randomly oriented elliptical cracks lead to the macroscopic stress criterion of failure indicated in Fig. 1 (a). Fig. I (a) is to be interpreted in the following way: P and Q represent the maxi mum and minimum principal stresses (compression is considered positive) in a macroscopically isotropic body; fracture will not occur for any combination of principal stresses lying within the 'fracture curve' shown, but

Jan 1, 1967

Jan 1, 1955

Three meetings of the Institute for the presentation and discussion of technical papers were held in 1913: The 104th meeting, comprising the Annual Business Meeting as well as technical sessions, was held at New York, Feb. 18 to 20, 1913; the 105th meeting was held at Butte, Mont., Aug. 16 to 21, 1913, at which papers obtained largely through the efforts of the Committee on Precious and Base Metals were presented; and the 106th meeting was held at New York, Oct. 16 and 17, 1913, under the auspices of the Iron and Steel Committee.

Jan 1, 1917

By Horace Pops, J. F. Libsch

THE discovery of SAP alloys (sintered aluminum powders) by lrmannl has stimulated investigations in other alloy systems.23 Not only do such alloys have good room-temperature properties, but they maintain high strength after prolonged service at elevated temperatures. In addition, they show high structural stability, including unusually high recrystallization temperatures. These characteristics are secured by dispersion hardening. For this investigation, Zn-ZnO alloys were selected. Practically, the fact that commercially pure zinc recrystallizes near room temperature prohibits strengthening and hardening by cold deformation and therefore limits the application of zinc where mechanical strength is important. Similarly, the poor

Jan 1, 1961

By V. Rajaram, H. W. Earnest, A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneumatic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 2700 t/h (3000 stph) to the backfill level, situated about 610 m (2000 ft) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This Paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1980

By H. F. Silver

Although the literature indicated that a hydrogen-ated coal bitumen might be used as a substitute for petroleum asphalt and road tar, no work could be found in which the material was actually used or evaluated as a road binder.' Therefore, a study was initiated to investigate the production and properties of a road binder made by hydrogenating coal in the presence of a solvent at elevated temperatures and pressures. HYDROGENATlON PROCEDURE Four different samples of sub-bituminous Wyoming coals and three samples of coals from other states, ranking from lignite to a low-volatile bituminous coal,

Jan 1, 1969

HUDSON MAXIM, Brooklyn, N. Y.-Immediately after the creation of the Naval Consulting Board, Admiral Strauss, Chief of the Bureau of Ordnance of the Navy, told members of the Board that the most important problem for the scientists to solve was erosion in large guns. The Navy, for years, had been working on the problem with marked suceess, but there was much yet remaining to be accomplished. As Chairman of the Committee on Ordnance and Explosives of the Naval Consulting Board, I communicated with several experts in the manufacture of steel, principal among whom was Prof. Howe. He generously agreed to help in every way possible, and the work that he has done and the time that he has spent upon it can he appreciated only by reading his paper. Prof. Howe asked for some rings. from a, certain 14-in. gun which Admiral Strauss had mentioned in particular, and in which, he had informed us, at each shot the bore of the gun, was enlarged about 0.001 in.,' and that after a relatively small number of rounds it was considerably eroded. It has puzzled scientists for a long time to account for the peculiar erosive effect produced by the powder gases in a gun, arid: what Prof. Howe has done in his paper is worthy of Sherlock Holmes. He is a veritable Sherlock Holmes of science.

Jan 4, 1918

By Thomas Fraser, Robert MacLachlan

The dry cleaning of coal is a relatively new art and, as might have been expected, a number of unforeseen problems have been brought to light in the few years that dry methods of treatment have been in commercial use. The pneumatic concentrators that were first adapted to the cleaning of coal had already been developed to a fair degree of efficiency, although at low ratings, in the field of ore dressing. The concentrating machines, therefore, were in a relatively more perfected state than the general technology of dry cleaning and, for this reason, the major difficulties encountered in the early plants were in the accessory operations involved in the servicing of the cleaners rather than in the functioning of the cleaners themselves. The crudities of a new technology were further aggravated, in some cases, by meagerness of appropriations which precluded even the provision of adequate storage bins and such other facilities as had been long recognized as indispensable to the proper functioning of older types of cleaning plants. The practice of dry cleaning is now sufficiently established so that we may examine critically auxiliary equipment and operations. The cleaning processes have been so simplified, with respect to presizing of the raw coal required and the quantity of air circulated, that stinting of expenditures for auxiliary equipment is not necessary to keep the per ton cost of installation in line with complete and well designed plants of other types. Furthermore, sufficient operating experience has been accumulated to ascertain the conditions most conducive to effective operation of dry-cleaning machines; at least the essentials of a definite technology of dry cleaning has been established. Early Operating Problems The problems that have occupied the builders and operators of dry-cleaning plants from the beginning have been relatively few, but difficult of solution. The principal difficulties have been: 1. The proper sizing of the raw coal to suit the cleaning process. 2. The handling of raw coal when it is delivered wet from the mine. 3. Dust collecting. 4. The maintenance of uniformity in cleaning performance.

Jan 1, 1931

By Y. L. Yao

A scale based on existing data for the mutual solid solubilities of metals in binary systems has been compiled. This scale is useful for estimating the relative magnitude of two solubilities, provided that these two metals do not form a continuous series of solid solutions. In his classic work on the theory of metallic solid solutions, Hume-Rothery proposed that, other things being equal, a metal of lower valency should be regarded as more likely to dissolve one of higher valency than vice versa. He called this the "relative valency effect". Later he found that the application of this general principle was limited to the three univalent metals: copper, silver, and gold. In dealing with alloys of these metals with metals of higher valency, Hume-Rothery stated, it is usually found that the solid solution of the univalent metal is of the greater extent.&apos; The question of whether there is a systematic trend in comparing the relative magnitude of mutual solubilities, if valency is not considered a criterion, naturally arises. The present paper proposes a "mutual solid solubility" scale on an empirical basis. The order of its arrangement is determined by the relative magnitude of mutual solid solubilities. Some applications of and inferences from this scale are given. ORIGIN AND SCOPE OF THE SCALE An extensive survey of over 400 binary phase diagrams shows that, with certain exceptions and within certain limitations, metals can be arranged in the following order: Na Zn Cd Ga Bi Ge Sb As Hg Sn Si Mg Li Ba In Tl Pb Al Ca Be Mn Cr Re W Mo Cu V Ta Fe Ru Cb Co Ti Hf Ni Os Zr Ir Pt Au U Rh Ce Pd Ag Th so that a metal higher on the scale tends to have a higher solubility in a metal lower on the scale than vice versa. some experimental solubility data are given in Table I. These data, unless otherwise specified, are taken from Hansen and Anderko.6 Throughout this paper, the term "solubility of A in B" is taken to mean the maximum solid solubility of A in B in atomic percent, while the maximum solid solubility of B in A in atomic percent is called "reciprocal solubility". The exceptions found in the above-mentioned survey are: Al-Ag system, 20.34 at. pct Al in Ag, 23.8 Ag in Al; Mg-Pb system, 5.9 Mg in Pb, 7.75 Pb in Mg; As-Sn system, vanishingly small amount of As in Sn, a large As primary solid solution; Cd-Hg system, Cd in Hg <Hg in Cd; Mg-T1 system, 5(?) Mg in ßT1, 15.4 T1 in Mg; W-Ti system, -21 W in ßTi, -25 Ti in W; Zr-Ag system, probably small amount of Zr in Ag, 20 Ag in ßZr.7 Considering the large number of examples, the exceptions are few. It is remarkable that metals may be so arranged without considering other factors such as size, crystal structure, electronic structure, and so forth. A limitation to the use of the scale is the fact that it cannot be tested for two metals forming a continuous series of solid solutions. It is interesting to point out that when the continuous solid solutions have a miscibility gap the critical composition is

Jan 1, 1961

By N. H. MacMillan, W. M. Mularie, R. E. Jackson, A. R. C. Westwood

The initial results of a study of the environment-sensitive microhardness and diamond rotary drilling behavior of granite and its constituent minerals quartz and feldspar (microcline)1 have established that many similarities exist between the environment-sensitive mechanical (chemomechanical) behavior of these materials and that of the simpler solids such as periclase, soda-lime glass, and alumina4 studied previously, at least as far as n-alcohol (straight-chain alcohol) environments are concerned. The results of this study (hereafter designated study I) also suggested that the rate of drilling of granite in these environments is controlled by the chemomechanical behavior of its quartz constituent, and is greatest in those environments which impart a zero l-potential to this phase, thereby maximizing its hardness. Now, cationic surface-active species strongly influence the l-potentials of silicate minerals. For this reason they are widely used in mineral separation operations. In particular, dodecyl trimethyl ammonium bromide (DTAB) was found in study I to produce f 0 for quartz at a concentration in water of 107 to 10-4 moles per 1. Accordingly, the influence of dilute aqueous solutions of this surfactant on the drilling behavior of granite also was examined in study I. This revealed that granite could be drilled three to four times faster in 10-° molar aqueous DTAB than in water, and confirmed by experiment the suggestion that granite is most effectively drilled with a diamond core bit in environments which impart a zero l-potential to quartz. According to O&apos;Connor and Buchanan&apos; however, the isoelectric point for quartz in aqueous DTAB solutions occurs at a concentration of .•.•2 x 10-° moles per 1, rather than [101 to 10-1] moles per 1. To confirm the results of study I, therefore, a more comprehensive investigation of the [ ]-potentials of quartz, microcline, and Westerly granite in aqueous DTAB environments has now been undertaken. At the same time an examination has been made of one of the basic assumptions of the current conceptual understanding of chemomechanical effects. In this view, although hardness changes occur essentially instantaneously following wetting of the solid, they are confined to a surface layer at most a few micrometers (µm) deep. Hence, to maximize the influence of chemomechanical effects on bit penetration rate only shallow cuts should be taken. Practical penetration rates are then obtained by increasing bit rotation speed. Experimental l-potentials were determined by the streaming potential technique using an automated rapid-cycling apparatus recently developed by Martin Marietta Laboratory from a design by Somasundaran and Kulkarni. The drilling studies employed 3.2-mm-OD 120-grit diamond-loaded core bits with a wall thickness of ~0.7 mm, and bit rotation speeds of 2200 and 25,000 rpm. The load applied to the bit was independent of the depth drilled in both cases. The 2200 rpm measurements employed the same drill press and puddle drilling technique as used in study I. The higher rotation speed was obtained using a water-driven dental turbine drill. In the case, the surface active fluid was pumped down the axis of the bit to ensure efficient wetting and flushing of the drilling debris from the hole. In both cases drilling rate was measured by the parameter D(200), defined as the average rate of bit penetration during the interval from 150 to 250 sec after drilling commenced.

Jan 1, 1976

By T. J. O’Neil, S. J. Kirk

In 1978, a multidisciplinary team from the University of Arizona, the Mines Project Group, conducted a study to examine reclamation alternatives for a proposed open-pit copper mine. The cost of a waste dumping plan designed by a mining consulting firm was determined as well as the cost of dumping configuration prepared by the Mines Project Group. The latter dumps were designed to be more socially acceptable and aesthetically pleasing, in addition to serving more creative end land uses than the dumps designed by the mining consultant. One dump configuration designed by the interdisciplinary team was the least expensive plan of all the alternatives considered.

Jan 1, 1984

By Wilbur Jurden

THE writer&apos;s first experience with a nonferrous reduction plant of great magnitude was at the Washoe reduction works of Anaconda some 35 years ago. Here was a plant which had been planned with remarkable skill and foresight considering the time and the state of development of copper-plant practice in the year 1902. The designer utilized topography to fullest extent to provide proper sequence of operations and, what is most remarkable, to leave adequate space for future developments, most of which at that time were unknown. However, the practice then was to locate the various units of the reduction works at the most advantageous points of the existing terrain with little regard for tramming or other auxiliaries and then connect these various units by the essential trackage, conveyor systems, piping, etc., as the need developed. This occasionally led to undesirable track arrangements, sharp curves, and steep grades, especially when it became necessary to extend various portions of the plant. Conveyor systems also became rather complicated, running as they did at various angles, and such items as piping and electrical distribution were often found to be in the wrong place, entirely inadequate in size, or awkwardly arranged for any kind of extension. This condition was not peculiar to Anaconda, for all copper plants at that time were built in the same manner and it was the constant association with these difficulties which, in the year 1925, influenced the layout of the Andes Copper Mining Co. plant. In that plant all trackage was laid out straight and level, all conveyors at right angles to each other with minimum length and number of transfers. All buildings were placed parallel and the main structures were complete for all purposes so that auxiliary buildings and dog houses would not be added later. Piping and electrical work was provided for in the original layout and carefully designed to avoid additions and alterations, and careful study given to every movement of material throughout the entire plant so that it would be accomplished with the least possible effort. Naturally it was hardly expected to attain all these objectives perfectly but our efforts did succeed in creating a plant which was unique and outstanding for its time-1927. It was also most gratifying to find that these design principles contributed to considerable savings starting right in the drafting room, carrying through the construction and ultimately yielding savings in operations and manpower. Not only that, but such a plant gives the observer an impression of symmetry and order, is more attractive to the workmen, and unquestionably eliminates many accident hazards. However, the Andes plant buildings were fitted to the existing terrain instead of having terrain created to fit the buildings-an item which we found advantageous to correct on the next large plant. At Morenci in 1939, all of the desirable features of the Andes plant such as parallel buildings, etc., were incorporated; but we went one step further-power shovels were brought in to make the terrain fit the reduction works. The result at Morenci is well-known and needs no elaboration here, but the success achieved by the design methods used for this and previous plants naturally influenced and guided the layout of the Chuquicamata sulphide plant which is the largest yet conceived. Chuquicamata Plant Design At Chuquicamata several factors not encountered previously complicated the problem to a great extent. The most desirable location for the smelter would allow smelter gases to blow directly into the open-pit mine already producing 60,000 tons of oxide ore per day and employing 1550 men. This, of course, would be a serious condition and, therefore, we were forced to move the smelter to a less desirable location but followed our previous experience at Morenci and made the terrain fit the job. The most difficult problem, however, was the provision for receiving various types of ore both by rail and conveyor. These consisted of: 1-Sulphide-bearing residue from the stockpile from which oxide copper had previously been leached. 2-Sulphide-bearing residue coming direct from the leaching vats. 3-Sulphide ore crushed at the existing crushing plants and hauled to the concentrator in cars. 4-Sulphide ore from the new crushing plant adjacent to the concentrator. 5-Sulphide ore obtained

Jan 1, 1952

By Charles H. Jacoby

A decision was made by the management of International Salt Co. in 1960 to eliminate all waste products which were entering the waters of Lake Seneca. This was to be accomplished by the injection of waste slurries into an abandoned brine cavity. The effluent from the cavity was to be treated and used for the manufacture of salt or disposed by deep well injection into the Cherry Valley limestone. After several years of research and design, a construction permit was granted by the state of New York; the injection, recovery, and disposal wells were constructed and after a public hearing an operational permit was issued. A summary of the operational results of the system is given.

Jan 1, 1974

By Michael Chender

The current outlook for financing new copper production is not very encouraging. At a time when companies are slogging through a protracted period of low prices as well as having to accept lower profits due to more stringent tax and royalty schedules, banks are beginning to require companies to take a greater equity interest in new projects. Mineral resource financing, including copper, seems to have lost much of its appeal to the lending institutions, and loans of any kind to many of the developing countries -from which over half of new copper capacity could be expected to come-are being examined much more critically than they were in the late 1960&apos;s and early 1970&apos;s.

Jan 12, 1976

By Karl Sundberg, Allen Nordstrom

Interesting results were recently obtained in geophysical prospecting at the Questa mine of the Molybdenum Corpn. of America in New Mexico. This paper describes that survey, which was carried out during October and November, 1927, by the Swedish American Prospecting Corpn. It is hoped that the paper will make it possible for the mining man to form an opinion of the applicability of geophysical prospecting under difficult conditions, showing, as it does, the results when prospecting for small small orebodies with comparatively poor conductivity, in a region of rough topography. Some principles underlying electromagnetic prospecting not known to be published previously will also be given in an elementary way, with special attention to the general structure of the electromagnetic field. Geological. Conditions at Questa The property is situated in the Taos range of the Rocky Mountains in northern New Mexico. About this region, L. C. Graton says:&apos; The main range is made up of Pre-Cambrian granites, gneisses and schists but in the vicinity of Red River igneous rocks of later age are present almost to the exclusion of the older series. These younger rocks are divisible into two groups. The older of the two, probably Pre-Tertiary age, is represented by large intrusive masses of monzonite porphyry, usually containing considerable quartz. The more recent group comprises intrusive and probably effusive dark-colored andesites and coarse andesitic breccias, some of which contain fragments of the monzonite; there are also flows of rhyolite and beds of rhyolite breccia. The evidence regarding the relative age of the andesite and the rhyolite is not wholly satisfactory, but there is little doubt that the andesite is the older. The ore deposits, although occurring more commonly in the monzonite porphyry than in the rhyolite, nevertheless are believed to be genetically related to the rhyolite. They certainly cut the rhyolite or andesite in places, and hence fall in the late Tertiary. The molybdenite at the Questa mine occurs in veins in the alaskite granite porphyry belonging to the older part of the Pre-Tertiary eruptives. Overlying the granite porphyry is the granodiorite, capping the granite

Jan 1, 1929