Search Documents

By James A. Barr

When phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. TO attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per ccnt. of available phosphate, which, howrever, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney formation, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss. One of the largest temporary losses in the industry occurs in the Florida pebble district where the recovery of phosphate runs about 25 per cent. The loss is classed as temporary because most of the tailing has been collected in ponds and piles, where it may be reclaimed in the future should developments or improved processes warrant. In cleaning the Florida pebble phosphate, aside from the elutriatisn

Jan 1, 1916

By W. H. Blauvelt

The technical and engineering problems in the manufacture of coke are today the problems of the byproduct oven. Except in a few special localitics, practically no beehive ovens have been built in the United States for the last 5 or 6 years except as renewals of old plants, and during these years the total number of beehive ovens in existence has been steadily falling. On the other hand, the number of byproduct ovens has increased from 4624 in 1911 to a total of about 7660 in operation at the end of 1917; with 2800 building, this makes a total of about 10,460 which will be in operation in 1918, or shortly thereafter. Preliminary Government estimates place the total production of coke for 1917 at 56,600,000 tons, the largest tonnage in the history of the industry. Of this 34,000,000 tons, or 60 per cent., was beehive, and 22,-600,000 tons, or 40 per cent., was byproduct coke. Some time in 1918 the production of byproduct coke should pass the beehive output, and when the byproduct ovens now building are completed the total byproduct capacity will be about 40,000,000 tons of coke per annum, which is over 70 per cent. of the record-breaking total coke production of 1917. The reasons for these changes in the coking industry are familiar to all of us, and need not be discussed here. Improvement in Oven Design Since the byproduct oven was brought to this country from Europe, in 1892, it has been radically improved, and from the point of view of American metallurgical practice it is safe to say that the American ovens arc superior to those of Europe. The points of superiority are mainly those of larger units and larger output per unit, and the greater extent to which labor-saving machinery has been introduced. The increased output is largely due to the use of silica refractory material, which permits higher heats and shorter coking time than are employed in Europe. The modern American oven will carbonize commercially more than 20 tons of coal per day, and contrary to the European idea that slower

Jan 1, 1920

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

By C. D. Woodward

PRIOR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but. they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that are not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 7 ½ ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.), and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of ,the stations, however, is about 75° F. (24° C.), while the average temperature in some of the drifts and crosscuts is 92° F. (33.5° C.).

Jan 2, 1922

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

By William H. Grady

FactoRs entering into the market value of coal are its grade, and the cost of labor, material, and capital. Reduction in these costs cannot be expected in the future, and it therefore follows that greater economy in their use must be accomplished if it is desired to hold the present markets; more tons of product per unit must be obtained in a given time from both men and material, and means devised for increasing the percentage of lump and domestic sizes. This paper is presented for the purpose of inviting discussion and stimulating thought in regard to the influence of methods of procedure and plans of mining, upon the quality of coal, the economical use of labor, material, and capital, and the cost of production. Even the better methods of the present day leave much to be desired, and a review of the reasons and necessities for their use may be of value in pointing the way to more economical mining. The writer does not attempt to discuss untried methods of mining, but rather to state clearly and concisely a summary of the results obtained under the several methods of procedure that have been adopted. In some instances a high degree of concentration has been effected, and comparisons of the results obtained with the results of lesser degrees of concentration form an interesting study. It is believed that much may be accomplished in improving the quality, and in the more economical use of labor, material, and capital, by concentration, and it is to concentration in particular that your study is invited. The writer, who has occasion to visit many mines, most of which are under different management, has been inclined to the opinion that improvement has been retarded in many ways and that mining has not as yet been entirely freed from the early-day practices which were forced upon it. Practices resulting in lack of concentration, to which reference will be made, are: The absence of robbing, necessitating the frequent interposition of barrier pillars; lack of system and of proper supervision, resulting in losses of life and coal. These practices could not well be

Jan 1, 1915

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By E. R. Borcherdt

Methods and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. Exploration Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. For many Years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both Ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in Ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1943

By E. R. Borcherdt

Methods and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. Exploration Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. For many Years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both Ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in Ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1943

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled sloping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill sloping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per scope unit, experiments with horizontal cut-and-fill scopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war's ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By Arthur A. Center

WAR demand- motivated developments in the zinc industry during 1942. Stocks of Prime Western were built up and High-Grade remained tight. The Prince The Prime Western stocks are expected to be cut down and the demand for High-Grade more easily filled as the Depue reflux plant of the New Jersery Zinc Co. increases - production. Subistition of steel for brass in artillery shell cases will have a considerable effect on the zinc situation of the country one estimate of the saving in zinc in 1943 by this substitution being a little under 100,000 ton, of metal. The metal saved will, of course be High-Grade. If the substitution occurs, the present tight situation in High-Grade may be entirely relieved as new production comes on the market and zinc may find itself approaching a situation as comfortable as that of lead provided the supply of zinc-hearing raw materials is sufficient to keep all reduction plants tip to capacity production. The premium price of the per pound of zinc over set quotas which went into effect early in 1942, helped to bring about the new lead-slag-fuming plant and other new sources of raw materials.

Jan 1, 1943

By M. E. Lombardi

IN comparison with the mining industry the petroleum industry is new and inexperienced, and until now it might have been called the fortunate industry. Its great good fortune consisted in two things; a bountiful supply hidden by nature in the rocks of the earth, and a steady and large increase, during the past twenty-five years, in the demand for petroleum products. It is a remarkable fact that consumption of gasoline in the United States has shown an increase every year since automobiles first became important, and even in 1930 there was a four per cent increase, in spite of the universal depression; the estimated increase if the times had been normal, was ten per cent. This industry has, therefore, not passed

Jan 1, 1931

By George A. Hill

WE of the oil industry, devoted to freedom of initiative, free competitive enter- prise, and free American institutions, applaud, with one voice, affirmation by the President of the national will and purpose to preserve and to protect, against all aggressors, "our American way of life with our individual and national freedom." We subscribe utterly and completely to this guiding declaration and seek its further definition as applied to the oil industry. Fortunately for all, the policy of the Government, after adequate study and deliberation, has been given precise definition. The National Defense Advisory Commission, with its patriotic, highly qualified, and distinguished personnel, has unanimously agreed to and adopted twelve general principles governing national defense contracts and also fair labor standard requirements. The President of the

Jan 1, 1940

By J. E. McConnell

No. 1 Electric Furnace and Billet Casting Shop, located in Plant No. 4 adjacent to our new 12 inch merchant bar mill, represents Inland Steel Company's first venture into both electric furnace steelmaking and continuous casting. Construction of the shop began in September, 1968 with excavation and foundation work, followed by awarding of general construction and major equipment contracts from December, 1968 to April, 1969. The first heat was tapped from No. 90 furnace on December 18, 1970, and the first cast attempted on December 29, 1970. The rated shop capacity is 500,000 tons per year of semi-finished billets and blooms, and was justified on the basis of approximately 85 percent of the product mix falling into the special bar quality category of steel grades. Auxiliary equipment has been designed into the shop to pursue free machining steels, including leaded and tellurized grades. The start-up and operation of the shop for the first year was essentially based on a two-part philosophy: 1. Initially operate with the "open stream" casting technique to accomplish machine shakedown and operator familiarization and training. 2. Operate with special bar quality, or "submerged casting", practices, make necessary refinements and gain customer acceptance

Jan 1, 1972

By A. Weiss, W. A. Coster

The search for ore is characterized by a great variety of uncertainties, each of which can be resolved by obtaining information at a cost. Three exploration stages may be distinguished in which information can be obtained, based on inherently different cost structure: 1) the reconnaissance or scanning stage, 2) the examination or screening stage and 3) the project stage. This exploration sequence would roughly coincide with replies to questions as to: where, how, why and how much. As complete information in each stage is too costly to acquire, we must assess the probability that adequate information will be furnished by a limited amount of effort and attempt to maximize the expected value of ore to be found for a given exploration expenditure. Several problems are discussed relative to the mathematical formulation and possible computer procedures for determining the optimum allocation of a total exploration effort. Based on the available literature possible solutions to this problem are indicated. When scanning through published literature on mineral exploration, it seems at first that there is little room for substantial and systematic improvements in the efficiency with which the problem of discovery of new ore deposits is presently being handled by large organizations active in exploration. It appears equally difficult to offer something relevantly new which could generate a break-through in exploration thinking and cause a marked improvement in the ratio of successful undertakings to the total exploration projects started. On the other hand, a number of experts in recent years have urged that the problems in prospecting be analyzed in a more skillful and sophisticated manner than in the past. Their thesis is based mainly on the premise that the cost of finding mineral deposits will increase with increasing technical difficulties. In present large-scale exploration ventures, especially in those regions where outcrops and immediately visible geologic evidence are scarce, older methods of prospecting are increasingly being replaced by more indirect and systematic geophysical and geochemical methods with more emphasis on correct statistical design of exploration patterns. It is perhaps the oil industry which has made the greatest strides in developing statistically, well justified patterns in its search for oil; possibly because oil seepages, as indicators of the presence of oil, left off at an earlier point in time than did outcrops as indicators of base metals. Among the pioneers in the field of statistics and operations research, as applied to mineral exploration, the excellent works of Allais, Slichter, Koop-man, Mickey, de Guhnin, Krumbein, Griffith, Sichel, Krige, de Wijs, and Matheron may be mentioned. It should, however, be pointed out that three subjects of basic importance to the allocation of exploration efforts have so far received only scant attention in published literature, even by the aforementioned authors. In the first place, a more precise definition of the object of the search, i.e., a minimum-size orebody, seems to be outstanding. Secondly, a decision model is not a widely-discussed subject. Thirdly, no concentrated attempt so far seems to have been made to establish probabilities of the occurrence of economic deposits on a regional scale and to arrive at a slightly more accurate knowledge of the probability laws governing the deposition of ore. It is not the purpose of this paper to create new order in the complexity of uncertainties in which our decision processes in exploration necessarily have to be conducted. Rather, we intend to highlight some of the outstanding, hitherto unmapped territory, where diligent compilation and a utilization of present and historic data may statistically improve our chances of success. We hope that the contribution of this paper will lie in bringing allocation problems into better focus and in increasing the mineral industry's realization of the magnitude of the factors involved. THE MINIMUM-SIZE OREBODY The concept of target specifications for what constitute a minimum-size orebody in exploration is a rather variable one and depends to some extent on

Jan 1, 1963

By G. K. Manning, P. C. Rosenthal

USE of copper as an intentionally added alloy in steel and cast iron has rapidly expanded with-in the last fifteen years. It is estimated that in 1931 not more than 2000 tons of copper were so used; by 1941, however, this figure had grown to 13,000 tons. Tonnage figures during the war years have been restricted just as copper itself has been restricted, but copper-bearing cast irons and steels have played a part in the production of ordnance equipment. They are used in gun carriages, airplane landing-gear assemblies, scout cars, bulldozing equipment, army trucks, armor plate and many other instruments of war. These wartime applications have their counterpart in many peacetime applications; derricks, dredges, mine equipment, railway equipment, trucks, farm implements, automobiles, and tractors, all usually contain some parts made of copper-bearing steel or iron. An example of this is the Ford tractor which in 1940 contained over 300 lb. of copper-bearing steel castings. To this list should be added corrugated building sheet for exterior use most of which, at the present time, contains upward of 0.15 per cent copper. With the return to peacetime economy and the removal of wartime restrictions, it appears certain that copper cast irons and steels will find increasing application in civilian goods.

Jan 1, 1945