Search Documents

By N. W. Wickersham, Ward B. Blodget, Roberts R. Boyd

The year 1926 has seen few radical changes or developments in methods of drilling and handling oil wells, but it has been a year of steady progress and development in deep drilling and production methods. Probably the outstanding development of the year was recognition by the directors of the American Petroleum Institute of the importance of natural gas in the production of oil, and the Institute directors' resolutions in December, 1926, regarding regulation of gas production with oil by state legislation. This matter is extremely important and will receive the attention of the industry in 1927. Advances in Drilling Equipment The history of the progress of deep well drilling is the solution of problems as they have confronted the operator. As the prospects for deeper production have become apparent, methods of penetrating the earth to greater depths have been devised. Rotary Equipment Improvements in the construction and in the methods of operation of rotary drilling equipment have practically caused elimination of cable tools in California for all but shallow work. The rotary drill, from 1910 when it began to be a practical factor in California, has been making steady advances, first displacing cable tools for drilling to the oil sands in proved fields and later displacing the cable-tool outfit entirely. With the perfection of machinery for taking core samples of the formation penetrated, the rotary drill has become generally used for wildcat work, continuous coring being practiced when desirable. Deep Holes The use of the rotary drill has made commercially feasible the opening of oil fields at greater depths than was considered possible with cable tools. Heavier equipment has been promptly supplied as occasion has

Jan 1, 1927

By R. E. Holmes, T. W. Leland

The solution to the unsteady-state mass- and heat-transfer equations describing the adsorption of a dilute component from a gas stream flowing through a packed bed is readily applicable to the design of hydrocarbon recovery units. The solution to these equations depends on the assumption of a linear equilibrium equation to relate concentrations on the surface to concentrations in the gas. This assumption is shown to be justifiable for components which are very dilute in the gas stream. This approach permits the prediction of the effects of bed shape and size, cycle time, and gas mass velocity on the recovery of each component. It also allows the time and gas flow rate needed for regeneration to be determined. The equations involve a constant for each component and another constant characterized by the type of adsorbent. These constants must be evaluated from operating data. Values of these constants determined for silica gel are presented. This paper points out the type of experitrrental data needed for a thorough design of hydrocarbon adsorption units. INTRODUCTION The growing importance of adsorption processes to recover hydrocarbons from natural-gas streams has created an urgent need for better methods to design and predict the performance of these processes. Since the original use of solid adsorbents in natural-gas processing was for dehydration, most of the current design methods for hydrocarbon recovery re extensions of those developed earlier for dehydration. These methods are based on an adsorptivity or bed loading factor defined as the amount of a particular component adsorbed per unit weight or per unit volume of the packed bed. The recovery of a given component is then expressed as an empirical function of its adsorptivity on a given adsorbent. In spite of the simplicity and initial utility of these methods, they are not completely satisfactory in that they do not predict the effect of the dimensions of the bed in relation to flow rate and cycle time, and do not predict the distribution of various components along the length of the bed. It is possible, however, to make a considerable improvement in the design of these processes by applying the basic equations of mass and heat transfer applicable to gases containing small concentrations of adsorbing components flowing through granular beds. These equations have been developed and solved by Anzelius,' Furnas,% nd Hougen and Marshall." where G = mass velocity of the inert constituents (assumed to be methane), lb/hr-sq ft, y = weight of an adsorbing component in the gas per unit weight of inert, lb of a given constituent per lb of methane, x = bed length, ft, p, = packed bed density, lb/cu ft, P, = gas density, Ib/cu ft, f = void fraction in the bed, t = time, hours, and w = weight of a given component adsorbed per unit weight of adsorbate free solid, Ib/lb pure adsorbent. The term on the left side of Eq. 1 represents the flow rate per unit bed volume of a component entering less the flow rate per unit bed volume of that component leaving the differential bed length. The terms on the right side represent, respectively, the accumulation rates per unit bed volume on the solid and in the gas phase within the differential bed section. The last term is negligible for this application since pgfv is quite small in comparison with p, and G. The partial differential is determined by the mass-transfer rate between gas and solid in the differential section.

By KING HAMILTON GRAYSON

IRON and steel were the only basic industries in the Soviet Republic in 1928 that lagged behind the pre-war production on a comparative basis. This was due to the almost complete obliteration of all industrial units manufacturing iron and steel products during the Revolution, which resulted in the production of 1921 being only 4 per cent of that of 1913. By the end of 1927 the production of pig iron had reached a point equal to 70.5, per cent of 1913; steel was 84 per cent ; and rolled iron was 78 per cent. According to the. planned program of the Supreme Economic Council, the pre-war level of the iron and steel industry was to have been reached and exceeded during 1929-30. The production of the entire period from 1917 to 1928 in comparison with 1913, is shown in the following table

Jan 1, 1929

Discussion of the paper of GEORGE S. Rice, presented. at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2459 to 2492. WILLIAM GRIFFITH, Scranton, Pa.-I notice in the discussions and literature that emphasis is placed on rock dust, shale dust, and limestone dust, and I infer that these different. sorts of rock are ground up to produce this dust. -Is that right? MR. RICE.-That is correct, but we do not have to grind the limestone dust we are using in the experimental mine, as that is obtained from a quarry, and is used just as it comes; we can get it very cheaply, as it is a by-product of the quarries. MR. GRIFFITH.-Have any experiments been made with ordinary dirt out of the fields; could not that be used as ground dust? MR. RICE.-If you dry it and powder it enough so it will float in a, strong air current it might be all right for the barriers, but if it is damp there will be a tendency for it to mat together; then it would be quite useless for making a dust cloud. There might also be another disadvantage if used through the whole mine, if it had very much free silica in it, which is bad for the lungs. Limestone and selected shale dust would not affect the health of miners. MR. GRIFFITH.-In order to do very much good with any of those barriers, they ought to be rather extensively used throughout the mines, and there are few mines that have facilities for grinding up this rock into such a fine dust. If the ordinary earth from a plowed field could be used, even if it were not quite so good, it is more accessible and very much cheaper; therefore, in using it, with the universality of the supply through-out the country, it would tend to stop explosions. MR. RICE (communication to the Secretary*).-In closing, it is well to again emphasize that I do not advocate barriers being a "cure-all" for explosions. It will be generally agreed that prevention is best, not only by means of improved methods of using explosives, and ventilation to prevent accumulations of firedamp, but also by either thoroughly wetting the dust throughout the mine, or else so treating it with rock dust or other inert dust that an explosion cannot start. From my observations I believe that rock dusting. is a practicable method, and has the merit of visibility, and remaining effective for considerable periods, whereas the watering method has to be daily followed up, and if neglected for a short period the mine may become in a dangerous condition. The Germans

Jan 4, 1915

By E. J. Bruderlin

A METALLURGICAL process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the dis-tillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working block must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort -to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retort-ing plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the- introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties.

Jan 1, 1936

The committee appointed .by W. R. Ingalls, president of the Mining and Metallurgical Society of America, to nominate candidates for the' annual gold medal of the Society consisted of E. G. Spilsbury, J. E. Johnson, Jr., and Bradley Stoughton. This committee recommended Mr. Schneider of the Creuzot Works in France for achievements in ferrous metallurgy, which recommendation was approved by the Society. From the report of the committee, the following facts relative to Mr. Schneider's career are taken: Born in 1868, Charles Eugene Schneider undertook the management of the Schneider establishment in 1898, after the death of his father, Henri Schneider. Under his enlightened management, the Schneider establishments have been considerably extended, their activity being not only directed to increasing production, but also to spreading more and more their scope for action in all branches of industry-in metallurgy, mechanical and electrical construction, shipbuilding, artillery and ammunition, and in public works. During the 10 years preceding the war, the number of employees in these establishments, and without counting those of the more numerous subsidiaries, increased approximately 50 per cent. While giving to peace industries all the attention necessitated by the progress in science and the continual improvement in industrial methods and products, Eugene Schneider, with a perspicacity that recent events have justified in a striking manner, especially directed his

Jan 3, 1919

By Raymond H. Young, Paul Sennett

INTRODUCTION Kaolin clay, consisting largely of the mineral kaolinite, is widely used as a white pigment. In the United States, for instance, pigment kaolin production was nearly 6,000,000 tons in 1976 (1). Production for this year should be significantly above this level. Current prices for kaolinite 'pigments range from about $20.00/ ton to$260.00/tony,depending on the amount of processing needed to make the final product. Although much of this pigment kaolinite is used as an inert filler where product specifications are not very rigid, a large quantity of kaolinite is converted to products where very restrictive specifications exist. These specifications set severe limits on such properties as viscosity in a water suspension, particle size distribution, color, and brightness. This discussion will concentrate on methods available to improve the color and brightness of pigment kaolin and will review the advantages and problems associated with these various methods. The term "brightness" refers to the reflectance of the pigment to blue light (2). Since even the brightest commercial kaolins have a somewhat yellowish color, the blue reflectance (or brightness) is a reasonably good measure of their nearness to a perfectly white material. I KAOLINITE STRUCTURE AND SOURCES The mineral kaolinite is an aluminum silicate and can be represented by the formula (OH) 8Si4A14010. The formula is frequently written

Jan 1, 1979

By M. Vallée

This case study compares the actual production figures for the No. I and No. 2 copper orebodies of the Société Miniére Louvem, Val d'Or, Quebec, with the preproduction estimates and a postmortem geostatistical estimation using kriging techniques. The deposits considered are small subvertical sulphide orebodies which were mined from August 1970 to April 1973, producing 648,000 tons at 2.04% Cu versus the 1968 computed reserves of 671,000 tons at 2.51% Cu (with 20% dilution), thus showing a 25% overestimation of the copper contained. The postmortem geostatistical estimation based on the same 44 D.D.H. intersections available in 1968, shows 2.24% Cu (no dilution), compared to 3.23% Cu (no dilution) given by the conventional section method. Block by block kriging techniques were used, but within the ore contours as determined by the geologist. In this case, Characterized like many sulphide deposits by highly dispersed sample values, geostatistical kriging techniques permit a more realistic estimation of the metal contained within a given volume, than the conventional methods which overestimate it. This study has been conducted by the Mineral Exploration Research institute (IREM-MERI) for SOQUEM, and is one of the few case studies released with all pertinent data. More postmortem of this kind are required for geologists and geostatisticians to improve their methods and their "batting average".

Jan 1, 1977

By N. E. Norman

During the past few years the underground mining industry and the big hole drilling industry have been involved in a flirtatious courtship, but until recently this courtship did not appear to be taken too seriously by either party. However, many of the promises made by the big hole industry are beginning to come true. Improvements have been made steadily in techniques of mechanical boring of large diameter shafts, raises and tunnels, thus making the big hole industry a more stable partner in the eyes of the mining industry. The mining industry too has made many changes in planning that make mining more attractive to the big hole industry. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry, and examine the three main features of big hole drilling to determine how each applies to mining. Shaft Drilling Since 1950, numerous large diameter shafts have been drilled using rotary drilling techniques. Most of the larger diameter shafts have been drilled for the AEC for underground nuclear testing purposes. However, since 1960 several shafts have also been drilled for various mining companies, particularly in the United States. In 1967, rotary drilling shafts were either completed or in progress at the mining companies listed in Table I.

Jan 6, 1968

By W. S. Landis

IN brief, this is the story of an attempt to Americanize a process originally developed in Europe. The story will be recited in two sections, the first dealing with the process as developed by the European engineers; the second containing the improvements and modifications of American origin, together with some details of the operating results of the unit as finally assembled. Developments in other directions in this same field have not, up to the present, pointed out an economic future for the process, therefore our record here is largely a report of development progress. Whether some particularly favorable location will be found at some future time for a commercial installation cannot as yet be fore-told. The project is now at a standstill. The peculiar tools of the electrometallurgist should be of great interest to the zinc smelter. The low thermal efficiency of the zinc retort, its comparatively small-scale unit and its intermittent cycle as it stood in 1925, should make this art a particularly fertile field for the electric fur-nace. Yet in spite of years of work recorded in volumes of literature, and an expenditure of large sums of money, there is not a single electrothermic zinc smelter operating anywhere in the world. In this industry the electric furnace plays only a secondary part today.

Jan 1, 1936

By Arthur A. Center

HIGH GRADE zinc stocks were reported short early in 1943, but not Prime Western. Maximum production of High Grade was expected to be reached before the middle of the year, and demands of new brass mills were to take all of the increase. In February three premiums (A, B, C) of 2 3/4c. per lb. of zinc in ore were announced to encourage production from high-cost mines, the number of premiums being in proportion to estimates of ore-production costs.

Jan 1, 1944

By L. W. McKeehan, W. C. Elmore

THE magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter' first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel' single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. SPECIMENS The following list describes the specimens used in the present investigation. DESIGNATION DESCRIPTION A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which he gave the following typical analysis: C, 0.05; P, 0.038; 5, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick.

Jan 1, 1935

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By Stanley F. French

ELECTRICAL power and distribution for the sulphide ore plant is an addition and extension of the existing power system which has served the oxide reduction plant since its inception in 1914. The power plant is located at Tocopilla on the west coast of Chile, some 90 miles from Chuquicamata. A brief description of this plant and the existing transmission system is necessary to an understanding of the problems involved in the provision for the sulphide plant load. Originally the Tocopilla power plant consisted of four Escher Wyss turbines driving Siemens Schuckert generators, each rated 10,000 kw. At various times, units of 10,000 and 20,000 kw were added, all of which operated at 215 psi and 600°F at throttle. In order to improve the economy of the station, a Topping unit was installed in 1938 together with a high-pressure steam generator of 360,000 lb per hr capacity. This unit is rated at 11,000 kw and was designed for 750 psi, 880°F. The exhaust from this turbine passes to the low pressure station header for operation of part of the low pressure turbines. Total kw generated by the high pressure boiler, topping turbine and associated low pressure turbines totals 33,000 kw and the total station capacity is 113,000 kw. This installation proved one of the most successful of its kind, operating almost continuously. The original plant was of German design and consequently European characteristics were incorporated into the system, the frequency being 50 cycles and voltages of 500, 5000 and 100,000 were used for low, generator, and transmission voltages,

Jan 1, 1952

By Wilford S. Wright

FOR the past four years the management of the Black Hawk Consolidated Mines plant at Mogollon has conscientiously kept accurate records pertaining to cost of operation and the performance of certain equipment. These records have been valuable in coordinating the work in the mine, mill and power plant. Also, as to quantity and kind of equipment and supplies most suitable from the standpoint of economy and dependable operation, they have served as a guide. Through comparison with records at other mines, where the same things are being done in a different way, they have pointed out mistakes to be avoided. No outstanding accomplishments, either in costs or performances, are revealed; in fact, some of the results are perhaps quite inferior to those obtained at similar plants, but it is with the thought that more records should be published for the benefit of the mining profession that the author presents these data. To other operators and to mining engineers who are called upon to make estimates for prospective operations, the information herein should be helpful. GENERAL CONDITIONS Mogollon is in the southern part of Catron County, southwestern New Mexico. It lies near the western border of the Mogollon Range, 14 miles east of the Arizona line. Silver City, 80 miles to the southeast, is the nearest railroad point. The connecting road, over which supplies are hauled into camp by trucks, is an improved highway for about 50 miles; the remainder consists of graveled roads and unimproved steep mountain grades. One general supply truck and one tank truck make daily round trips. Hauling of supplies to the mine has cost at the rate of $0.08 per ton-mile; or, on the basis of ore production, $0.30 per ton mined. Lumber, hauled in from local mills, has cost an average of $30.00 per 1000 board feet, $8.50 of which has been for hauling. The annual consumption averages 108,000 board feet. Lime, hauled from a plant in Arizona, is about the only other item not brought out from Silver City. Fuel oil for the generation of power is the item of greatest hauling expense, the f.o.b. Mogollon cost of approximately $0.06 per gal. being nearly twice the f.o.b. refinery price. Water for power plant, mill and camp use flows to camp storage tanks through a 4-in. pipe line from a spring and intake 3 miles up Silver Creek Canyon. A few times, particularly in the month of June, mill operations have been suspended for two or three days because of water shortage. MINING CONDITIONS During the years 1938, 1939, 1940 and 1941, the mine produced 230,059 dry tons

Jan 1, 1943

By L. W. Casteel

St. Joseph Lead Company&apos;s Southeast Missouri mines have been successfully converted to the use of ammonium nitrate and fuel oil as a blasting agent. This is significant to the company because it means a savings of a quarter of a million dollars per year. It is significant to the mining industry because of the unusual conditions involved and the methods and materials used to overcome them. St. Joe has been mining the low grade lead deposits of southeast Missouri since 1864. This ore occurs as disseminated galena in widely scattered pockets within the Bonneterre dolomite. The daily production of 20,000 tons is obtained from several hundred small, room and pillar stopes covering an area 10 miles long and five miles wide. Distribution of explosives and other materials is a real problem. Drilling in the stopes is done with air legs, column- mounted machines or jumbos, depending on the size and location of the stope. Drill hole sizes vary from 1 3/8-in. diam down to 1 1/8-in. Each driller charges his own holes and shoots them at the end of the shift. Numerous shafts provide natural ventilation which is supplemented in isolated areas by churn drill holes equipped with blowers. Water, in most stopes, is not a serious problem, although the mines do produce about 20,000 gpm.

Jan 5, 1962

By Peter R. Morris

The effecl of preferred orienlation on X-vay dzffvaction measurements of retained austenzte was investigated for four precipitation-hardening staznless steels in sheet form. A method is preserzted for estimating the ervor in measurement associated with a given samplirig direction. The method was used to select an "optimum" sampling direclion in order to minimize errors in measurement due to preferred orientation. hleasuremenls of retained austenite content employing lhe proposed sampling direction are conzpaved to measuretnents enzploying the more commonly used normal direclion for a series of sawzples. THE first application of X-ray diffraction to the measurement of retained austenite in steels is due to Sekito, 1 who employed a photographic technique in which the (111) reflection from a thin strip of gold affixed to a cylindrical sample was employed as a standard. Averbach 2 introduced the "direct comparison" method in which the ratios of observed to calculated random intensity are assumed proportional to the austenite and/or martensite contents. Averbach&apos;s work forms the basis of most subsequent X-ray diffraction methods for the determination of retained austenite. Subsequent improvements are due to: Averbach and Cohen,3 who employed a sodium chloride crystal to monochromate cobalt radiation; Averbach et a1.,4 who introduced a bent sodium chloride monochromator; Mager,&apos; who used a bent quartz crystal to monochromate chromium radiation ; Littmam, who first used a geiger counter diffractometer for this purpose; Beu and Beu and Koistinen, 11,12 who studied effects of absorption factor, surface preparation, sample geometry, integrated intensity vs peak height, choice of radiation, monochromator, and filter. The possibility of errors in measured values due to orientation effects was noted by Miller,13 who suggested examination of a surface other than the plane of rolling. Lopata and Kula 14 have developed an experimental technique in which the preferred orientation is measured in each sample. They illustrated the method for a sample containing 42 pct retained austenite. Application of their technique to the 1 to 15 pct range typical for the precipitation-hardening stainless steels does not appear feasible. EXPERIMENTAL PROCEDURE The nominal compositions of the precipitation-hardening stainless steels investigated are listed in Table I. Ingots were solution-treated, hot-rolled to approximately 0.2 in., and reduced to 0.050 in. by a suc- cession of cold rolling and annealing operations. After this treatment the 17-4PH sample was in the marten-sitic condition, while the 17-7PH, PH 14-8Mo, and PH 15-7Mo samples were in the austenitic condition. Samples of 17-7PH and PH 15-7Mo steels in the mar-tensitic condition were obtained by heating to 1750&apos;F for 10 min and holding at -100°F for 8 hr. A sample of PH 14-8Mo steel in the martensitic condition was obtained by heating to 1700°F for 1 hr and holding at -100°F for 8 hr, followed by aging at 950" for 1 hr. POLE FIGURE DETERMINATIONS Samples were thinned to 0.003 to 0.005 in. by etching in a solution containing 250 ml reagent-grade phosphoric acid (85 to 87 pct H3PO4), 250 ml technical-grade hydrogen peroxide (30 to 35 pct H 2 O 2), and 50 to 100 ml reagent-grade hydrochloric acid (37 to 38 pct HCl). The specimens were placed in an "integrating" sample holder which provided a 1-in. oscillation in the plane of the sample. The diffractometer was aligned to measure the intensity diffracted by planes of the particular {hkl} type being studied. The sample was Set for a given latitude angle, a, measured from the plane of the sheet, and diffracted intensity recorded as the longitude angle, 0, measured in the plane of the sheet from the rolling direction, was increased from 0 to 360 deg. After a 360-deg scan of B, a was incremented by 5 deg, and the process repeated. Random standards obtained by spraying suspensions of powdered iron (bcc structure) and nickel (fcc structure) in lacquer were used to correct observed intensities for absorption and geometrical effects. Zirconium-filtered molybdenum radiation was used to determine the transmission regions of the (111) (0to 45 deg), (200) (0 to 60 deg), and (220) (0 to 45 deg) austenite and (110) (0 to 45 deg), (200) (0 to 50 deg), and (211) (0 to 35 deg) martensite pole figures. Vanadium-filtered chromium radiation was used to

Jan 1, 1968

By R. G. Bowman

LEAD is a dull and sober metal, and in times of economic stress it en- joys, or at least occupies, a position which partakes somewhat of its physical lethargy and stability. The past ten years have witnessed in this country a decline in the production of lead, and a shrinkage of ore reserves, following closely the general economic situation. Metal prices have not justified exploration and development of new sources. Momentary rallies in industry have brought no response from lead.

Jan 1, 1940

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the &apos;Juniors&apos; spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have &apos;a piece of the action.&apos; The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the &apos;long shots,&apos; many of which efforts by virtue of the Junior&apos;s perseverance coupled with a touch of &apos;ore is where you find it&apos; philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By AIME AIME

ABOUT one hundred were in attendance when Donald M. Liddell opened the session* on non-ferrous metallurgy at 2 p. m. on Tuesday. F. F. Col- cord was vice-chairman. For the first part of the session the chair was turned over to Frank G. Breyer, who introduced G. L. Spencer, Jr., to read his contribution (T.P. 378), "High Silica Retorts at the Rose Lake Smelter," which was an account of the method of manufacture of high-silica zinc retorts at the Rose Lake smelter, and of the service given by these retorts. The materials used are, by volume, 50 per cent clay, 25 per cent silica flour and 25 per cent grog. Written discussion of the paper by E. M. Johnson, W. R. In- galls and M. M. Neale was read by Mr. Breyer. Mr. Johnson explained that their practice in manufacture differed very little from Rose Lake practice, but that their retorts did not last as long, possibly because Eagle-Picher does not use a hydraulic retort press or sintered ore. He ascribes the longer life of silica re- torts to the fact that they do not bend under heat. Mr. Ingalls pointed out that silica retorts are no better as heat conductors than clay retorts, but that they do have a superior rigidity in the furnace. The character of the retorts does not affect the density of the charge. Mr. Neale gave the procedure in the manufacture and use of high-silica retorts at the Donora zinc works, not

Jan 1, 1931