Search Documents

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By Ernst A. Hauser

IN a paper published three years ago,' the term "silicic chemistry" was used for the first time to emphasize the increasing importance of the chemistry of silicon in science and technology. The development through which the colloid chemistry of siliceous matter has gone since then is in itself ample proof that the coining of this new term for this branch of colloid science was not presumptuous. Until quite recently, however, silicic chemistry concerned itself only with the composition and colloidal properties of natural and synthetic siliceous matter, but had not paid much attention to the genesis of this matter, particularly to that of the clay minerals. What is even more disturbing, particularly from an educational point of view, is the fact that neither mineralogy, geology, nor metallurgy has fully realized the important role colloidal phenomena must have played in the genesis of our planet and the formation of minerals generally speaking. Considering the importance of colloid chemistry today in the fields just mentioned, it is not surprising that the theories most agreed upon by geologists and mineralogists for the origin of clay minerals are not acceptable from a strictly colloid chemical point of view for the genesis of these most important and most abundant components of the earth. Of all the theories pertaining to the origin of clay minerals, those still most accepted by geologists and mineralogists are the "residual clay" and the "transported clay" theories.15 The former is based primarily on the assumption that the formation of clay minerals is the result of surface weathering of fresh rocks, or is due to the action of solutions. Taking the action of water on orthoclase as an example, the most recent ideas have been summarized by H. Jenny13 as follows:

Jan 1, 1952

By J. M. Morkowitr

A. Sawatzky (Atomic Energy of Canada, Ltd.)—The detailed criticism by Markowitz of my simple treatment of the thermal diffusion of hydrogen in Zircaloy-2 indicates that my paper was not as lucidly written as it could have been. I would therefore like to reiterate several of the main points of my proposed mechanism and describe in more detail some of the features only implied in the original paper. The distribution equation derived in my paper was stated to hold only for the case where the volume taken up by the hydride was small compared to the volume taken up by the solid solution phase, subsequent work, mentioned below, having shown it to be out by only a few percent up to a hydrogen concentration of about 3000 ppm. Of course, hydrogen in the two-phase region alone is not conserved in my treatment as pointed out by Markowitz. On the contrary, one of the important features of my proposed mechanism is that in the presence of a temperature gradient a two-phase region cannot exist over the whole specimen. For example, if the specimen is entirely a + 6 initially, then on application of a temperature gradient, a single phase (a) region at the hot surface develops from time t = 0 onwards. As mentioned in my original paper, the interface between the a and a+d regions moves toward the colder surface of the specimen with a discontinuity in hydrogen concen- tration developing at the interface and increasing with time. This interface moves at such a rate that hydrogen in the specimen as a whole is conserved. It must be pointed out that my distribution equation (Eq. [5] in Markowitz's paper) holds only for linear geometry. It is easy to show that for the cylindrical geometry of Markowitz the assumptions used in my treatment lead to

Jan 1, 1962

By G. W. Tuffnell, S. Floreen

Three Fe-18 pet Ni-base ternary alloys cortaining carbon, molybdenum, or cobalt were aged to pgroduce hardening by carbides, Ni3Mo, or ordering, respectively. Each alloy was tested in rotating-beam fatigue tests after hardening to 195 ksi ultim.ate tensile strength. The fatigue properties of three alloys soere essentially identical. The results suggest that tlze fatigae strength of an igron-base alloy should depend primarily upon the tensile strength, and not iipon the hardening mecaanisrn. THE fatigue strengths of many steels have been found to be directly related to their ultimate tensile strengths. For ultimate strengths below 200 ksi, the fatigue endurance limit at 107 to 10' cycles is approximately half the ultimate strength. Essen- tially all of the steels that have been tested, however, have been hardened by carbon. Thus it is not certain whether the relationship between fatigue and ultimate strengths is a general one that applies for other types of hardening in steels, or whether it applies only for the particular method of hardening by carbon. The recent developments of the martensitic precipitation-hardened stainless steels and the marag-ing steels have shown that it is possible to achieve high strengths in iron-base alloys by other hardening mechanisms than that due to carbon. Therefore, it is now possible to compare the fatigue properties of several iron alloys having the same ultimate strengths but hardened by different mechanisms. For the present study a binary Fe-18 pct Ni martensite was selected as a base material. This particular matrix composition has been found to have deformation characteristics very similar to pure iron.' Three ternary alloys were prepared by adding either 0.23 wt pct C, 5 wt pct Mo, or 20 wt pct Co to this base composition. After suitable heat

Jan 1, 1965

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses. One factor necessary for designing or evaluating a structure's stability is knowledge of the material's mechanical properties, such as stress-strain behavior and fracturing characteristics. The composition of most structural materials such as metals and concrete is uniform and reproducible to the degree that their mechanical properties in service are nearly the same as those measured in the laboratory. Consequently, a rational design can be made on the basis of published mechanical property values. The same equivalence does not exist for rock materials for two reasons: (1) the composition of even the most common rock types is highly variable, and (2) the problem of the size effect is present. Mechanical property tests not conducted at a scale that includes these effects in normal proportion will not be representive of the in-situ rock mass. Of course, the alternative is to perform the test in-situ. Comparatively few mechanical property tests have been performed in-situ because of the physical limitations of test equipment and the prohibitive cost. The current procedure is to design a structure based on small-scale laboratory measurements, with a safety factor usually determined by the experience of the design engineer. While this procedure is somewhat unsatisfactory, laboratory measurements can and do provide a useful basis for the initial design.

Jan 1, 1970

By J. Parke Channing

THE caving system of mining is that method of removing the ore from an underground body in which the top is first attacked and mined out and the capping, or roof, as the case may be, is allowed to fall in or "cave" and fill the space formerly occupied by the mined ore. It is applicable, generally, to large orebodies where the ore is relatively soft. We may say, within moderate limits, that when ore is removed the surrounding ground either caves in or remains open. For example, in mines like the Lake Superior amygda-loid copper mines, when the lode is removed there is left a void which remains open for many years; on the con-trary, mining a Lake Superior soft hematite ore, however carefully it may be done, always produces a caving of the surrounding rocks. We may say, with propriety, therefore, that the caving system is applicable to that type of ore deposit in which the surrounding rock readily caves. Another factor which governs the use of the caving system is the value of the ore itself. Admittedly, any form of caving will not extract 100 per cent. of the ore, and in the case of a very rich orebody it is often desirable to get out every pound of the ore with as little dilution as possible. Under these conditions, some other method of mining, such as that by square sets and filling, is indicated and should be followed. We may say, however, that, looking at it broadly, in the United States the caving system of mining is generally used for the removal of soft hematite and for the so-called "porphyry" coppers. In both cases this method is used where open-pit mining is not possible.

Jan 1, 1922

By P. J. Jorgensen, J. H. Westbrook

The anomalous indentation creep of nonmetallic solids is shown to be due to the presence of adsorbed water. Although a specific mechanism is not proposed, it is suggested that the water may be present in two chemically adsorbed states. DEPENDENCE of the indentation hardness of solids on the time of load application was first studied systematically by Hargreaves1 in a study of lead and certain low-melting alloys. This technique has become known as indentation creep and has been exploited particularly by underwood and by Mulhearn and Tabor3 as well as by others.4°7 For metals good correlations have been found between the time dependence of hardness over several orders of magnitude in the seconds range and creep parameters from conventional tests at the same temperature where creep strains were measured over hundreds or thousands of hours. However, Walker and Demer8 and Mitsche and Onitsch9 observed extensive indentation creep at room temperature (particularly for light loads) in certain minerals and in materials such as lithium fluoride and magnesium oxide for which conventional creep is ordinarily not observable unless the testing temperature is at a very much higher fraction of the melting point. Normal behavior was observed' for metals such as copper, i.e., negligible time-dependent flow during room-temperature indentation. Walker and Demer attempted to find some distinctive difference in the surface deformation markings about indentations in the anomalously behaving materials at short and very long indentation times. No significant differences were observed. Increased duration of loading was found, however, to result in an increase in the length of glide of edge-dislocation loops extending into the interior of the crystal. Jorgensen and Westbrook,10 in a recent study of

Jan 1, 1965

IN THE early evening of October 15, 1954, a large specially designed truck, convoyed by a second smaller one, arrived at Silver Bell, Arizona, completing a ten-hour 110-mile journey from Phoenix. The big truck was driven through gaps left in a previously prepared concrete foundation, the load was jacked up, the large girders that constituted the bed of the truck were pulled away, and the load was then lowered into place on the foundation. A crew of two men, the two truck drivers, finished the job in a little more than an hour. When they were through, a complete and attractive three-bedroom house, prefabricated in Phoenix, was almost ready for occupancy. About all that remained to do was to connect the utilities-water, electricity, plumbing, and gas. The kitchen and bathroom equipment and appointments were superior in every respect, and there was a built-in car port for the automobile of the prospective residents. This family domicile was one of more than one hundred, each averaging about $8,000 in cost, that the American Smelting and Refining Company has provided for its employees engaged in mining and milling 7,500 tons per day of low-grade Porphyry copper ore. Aside from the fact that it is more economical-partly because of the variety of union craftsmen needed to build and equip a house-to do the work in a city 110 miles away, the significant point is the high quality of housing that is provided for what may be called in nostalgic vein the "mining camp" of 1955. Silver Bell is typical of all the Porphyries in this respect though the community is relatively small. At San Manuel

Jan 1, 1957

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons- per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead, mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding, and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1952

By Paul Weir

DURING the past decade, methods of producing bituminous coal in the State of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of pro-duction by various methods in the State of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties.

Jan 1, 1939

By M. A. Mallinger

A series of laboratory tests was conducted to determine the limits of practicability in regulating the weights of various cement slurries. It was found that slurry weights of 12 to 19 lb per gallon could be obtained by adding bentonite to decrease the weight and barytes ore to increase the weight. It was also found that barytes ore was not usable in all cements. LIGHTWEIGHT CEMENT SLURRIES INTRODUCTION During the drilling and completion of oil wells the magnitude of the hydraulic pressures exerted on certain formations is critical. In many cases considerable care must be exercised to prevent drilling mud weights from becoming too high, and in those wells where loss of circulation is a problem, the use of normal weight cement slurries will generally result in lost returns during casing cementing operations. While mud weights can easily be controlled, it is necessary to exercise care in the selection of weight reducing additives for cement slurries in order that slurry weights may be reduced sufficiently to prevent the loss of a large portion of the cement to the thief formations without seriously affecting the setting properties of the cement. EXPERIMENTAL RESULTS An extensive search revealed that a large number of materials .that might have been otherwise practicable as a weight reducing additive were not acceptable for use with oil we cements because the imposition of pressure on the slurries caused the additive being tested to be compressed or to absorb water from the slurries, resulting in negligible decrease in the slurry weight. This search for lightweight additives disclosed that bentonite, a material very commonly used for reducing the weight of drilling muds and cements, produced the best results without undue harmful effects on the properties of oil well cements. It was found that there was a limit to the amount of benton-

Jan 1, 1950

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By N. J. Gran, W. R. Opie

HYDROGEN in molten aluminum and aluminum alloys, which precipitates during cooling and solidification, is the principal cause of pin hole porosity in ingots and castings. Much attention has been given to determining the effect of temperature and pressure on the solubility of hydrogen in pure aluminum, but little data are available on hydrogen solubility in aluminum alloys. This investigation was undertaken to check results reported for pure aluminum and to show the effect of silicon and copper additions on the amount of hydrogen contained by molten alloys. Previous determinations of the solubility of hy-drogen in molten pure aluminum are plotted in fig. 1. The most reliable data appear to be those of Ransley and Neufeldl and of Baukloh and Oester-len.' The latter authors also report some results on the effect of copper and silicon additions. Up to 6 pct these elements decrease the solubility of hydrogen quite rapidly, with a definite minimum noted at 6 wt pct for both copper and for silicon, although no reason is apparent for these minima. Experimental Procedure The solubility of dry hydrogen in pure aluminum, aluminum-silicon, and aluminum-copper alloys was determined by the method of Sieverts.8 This consists of determining the volume of the gas system above the molten metal at a given temperature and pressure by using an insoluble gas. This volume is referred to as the "hot volume." The system is then evacuated and the soluble gas is introduced at the same temperature and until the same pressure is reached. It is necessary to introduce enough of the soluble gas to fill the space above the metal plus the soluble amount. The difference in the volume of soluble gas and the "hot volume" is the solubility. The accuracy of solubility measurements by the Sieverts' method is primarily depend-

Jan 1, 1951

By M. E. Wadsworth, D. R. Wadia

The rate of reaction of cuprite was measured in a series of sulphuric acid solutions, from which oxygen had been excluded, at various concentrations and temperatures. The overall reaction CuzO + H2S04 + Cu " + CuO + H20 + So4' may be explained quantitatively by two simultaneous rate reactions involving not only H+ but also the hydrolytic adsorption of H2SO4. The results indicate the importance of considering surface mass balance relationships associated with heterogeneous surface reactions. T EACHING has long been an important method for the recovery of metals from certain minerals. Many processes have assumed minor importance in modern practice but such operations as the recovery of uranium and present interest in high pressure-high temperature solution of sulphides' ' well illustrate the importance of leaching as a unit operation. Little quantitative information is available in a form sufficient to determine the mechanism of solution at the solid-aqueous solution interface for given systems. For this reason, it is important that fundamental studies of leaching processes be conducted so that parameters associated with such surface reactions may be understood and correlated. Cuprite was chosen for this study as a result of a recent investigation carried out at the University of Utah on ores of the Ray and Chino Mines Divs. of the Kennecott Copper Corp. These sulphide deposits contain sufficient oxidized minerals, such as cuprite, malachite, and azurite, so that recovery of metal values contained in the oxidized fraction is of primary interest. Of these oxides, cuprite (Cu,O) is the most interesting, since it dissolves in sulphuric acid by an oxidation reduction couple resulting in the formation of 50 pct metallic Cu and 50 pct cup-

Jan 1, 1956

By Peter I. Brooker

Elementary estimation methods in which blocks are assigned values according to a geometrical area of influence concept are investigated for a tabular deposit. This quantitative assessment of the estimation technique is made using Matheron's geostatistics which allows the variance of the error between actual block values and estimated values to be found once the semi-variogram is known. For the deposit in question it is shown that the elementary technique makes poor use of the available information. There is a 20% relative error associated with it, whereas by using the optimal technique of kriging this can be reduced to 9%. An infill drilling program, which might have been suggested on area of influence results, would reduce the estimation variance only marginally over that of the current campaign; the relative error being lowered to 6%. Thus the geostatistical analysis shows this would be an unnecessary expense. The accuracy of an earlier drilling stage is also studied and it is shown that with the information available at the earlier stage block values could have been known with a relative error of 13%. Drilling could have stopped then if this were reckoned a tolerable error level. These results are all obtained for blocks whose size is dictated by the mining engineer and is set at the current grid size. In the area of influence approach smaller blocks are considered as the grid becomes finer and a study of the accuracy of area of influence estimates and kriged estimates for differing block sizes is presented. Between drilling stages more information from which the semi- variogram is calculated becomes available. The sensitivity of the estimation to changes in the semi-variogram parameters between earlier and current drilling programs is investigated.

Jan 1, 1977

By H. E. Stauss

THE short-time tensile-strength test, while it has not attained the practical importance of the creep test at elevated temperatures, has the advantage of being rapid and is satisfactory for determining relative strengths. For platinum and its alloys, which frequently are used at high temperatures under ill-defined conditions, the short-time test provides useful data that aid in the selection of the most promising alloy for each use. Measurements have been made upon 13 alloys, using wire 0.0031 in. in diameter, the choice of alloys and of wire size being determined by the requirements of a practical problem. Later the measurements were extended to higher temperatures by the use of heavier wire, 0.010 in, in diameter. APPARATUS The use of fine wire made the necessary equipment very simple, since no effort was made to measure the elongation. A small platinum-wound horizontal furnace was used, ½ in. in internal diameter by 1 ft. long, with the wire threaded through it. The wire, clamped at one end while the other ran over a ball-bearing pulley, of a total length of 29 in., was loaded directly by running sea sand into an attached basket, making the rate of loading and not of elongation constant. The sand flowed from a funnel, under a head of 3 in., into the basket. 3 in. below the orifice, at the rate of 170 grants per minute. Pulley friction and bending resist-ance of the wire as well as the force of impact of the sand could be neg-lected, being 3 grams and 0.5 grams, respectively. Furnace temperature .was uniform within ±5° C. over a length of 3 in., although a drift with time occurred, the largest amount being 20° C. No provision was necessary for a controlled atmosphere.

Jan 1, 1939

By Henry M. Howe

What should be the chief aim of a metallurgical laboratory ? Before answering this, let us ask, What should be the chief aim of metallurgical instruction ? Taking a definite case, that of the iron blast-furnace, should we chiefly teach the methods of bosh- and tuyere-cooling, of storing and assembling materials, of removing the iron and cinder, of firing boilers and cleaning stoves ? Or should we aim chiefly to lay clear and bare the nature of the reactions which occur in the blast-furnace, the reason why changes in the rate of driving, in the blast-temperature, in the composition of the cinder, cause their known effects ? Shall we chiefly describe or explain ? Shall we teach chiefly the looks or the reasons ? Put thus, the question admits but one answer. Hours of labored description at a technical school give a less true and clear view of actual metallurgical operations than a brief visit to metallurgical works. If in my teaching 1 take the far more laborious course and lay so very great stress on explanation and so little on description that I seem to err on that laborious side and not to give description enough, the student will quickly make up for my lack of description in his first weeks in the works; he will there learn quickly and easily what I could have described only obscurely and with labor. Details of practice are learned easily and retentively in the works, but with difficulty and slowly at school. With the principles, and especially the chemical principles of metallurgy, the reverse is true. The works have little facility for teaching them; the school has every facility. The place then for explaining, for teaching principles, is the school. But,

Jan 1, 1900

By Fred A. Krafft

The time allotted to this paper will permit only the sketching of general principles and practice as generally employed in the industry to maintain and preserve the physical well-being of the miner and his family. Let it be emphasized on behalf of the industry that coal opera- . tors, individually and collectively, have given primary consideration to the appointment of a mine or community physician who is charged with the responsibility of caring for the sick and injured. However, it too frequently happens that with the selection or appointment of the camp doctor many operators wash their hands of further responsibility toward the health and the working efficiency of their employees. The coal industry is so organized in most of the coal-producing areas that not only is the health of the individual miner an important production problem but the collective health of the entire mining community is a fundamental operating problem. This is particularly demonstrated when epidemics of communicable diseases attack entire communities, with resultant loss of life and production and general community distress. The problem and responsibility of maintaining high health standards among miners and their families should be given as much consideration as safety, economical production and efficient distribution are given in the successful operation of coal mines. Company Policy In the inauguration or administration of a medical program for a large mining operation or for an individual mine, the first question to be solved is what the company policy is to be with respect to the following factors pertinent to a medical program: 1. On what basis will the company and the employees finance the program ? 2. Should a contract doctor or a full-time doctor on salary be employed ? 3. What measure of service is to be rendered the employee and his family in return for his monthly contribution to the medical program?

Jan 1, 1936