Search Documents

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By Leo F. Reinartz

Part III of a four-part series on the history of steelmaking in the US, describes furnace developments, improvements during the last few decades, and the contribution of the AIME. THE invention of the dolomite machine was a great boon to the open-hearth furnaceman. By speeding up bottom making, it helped to increase tons per hour and decrease cost. The first homemade unit was built and operated before 1925 at the South Side works of Jones & Laughlin Steel Corp., Pittsburgh The first commercial machine, similar to those known today, was built for the Donner Steel Co., Buffalo, N. Y., in 1925. Heavy slab buckstays, 6 in. by 15 in., supplanted lighter I-beam buckstays as furnace framework in the middle 1920's. They greatly improved the rigidity of the furnace binding. Although the first sloping back wall had been in- stalled prior to 1920 on a small basic open-hearth foundry furnace at Columbus, Ohio, the impetus to install such back walls universally in ingots shops came after S. Naismith installed the first one on an open-hearth furnace at Illinois Steel Company's South works in June 1924. Before that event, back- wall life had already been improved somewhat by the use of chrome rock or metal-encased basic brick. Here again, these changes heralded major for- ward steps in furnace design, decreased costs, in- creased production, and improved safety and working conditions on the back standing of the furnace. Fuels Up to 1930, a number of different kinds of fuel were used to melt and refine steel in American open hearth furnaces. During World War I, powdered coal was used in a few plants as an open-hearth fuel, but because of the high sulfur and ash content in the coals, many operational difficulties arose. There were also dust, explosion, and accident hazards, so that after the War its use was discontinued. In some steel-manufacturing centers, natural gas was available as a fuel and gave good performance. In most steel-manufacturing centers, operators had to rely on producer gas made from bituminous coals in producer gas houses. Low-sulfur low-ash, high-fusion coals required for the manufacture of such gas were not readily available. The quality of producer gas was uncertain. The gas had to be pre-heated. Maintenance problems connected with the use of this fuel were serious. Tons per hour per month was unsatisfactory. Although petroleum had been first discovered by Edwin L. Drake at Titusville, Pa., in 1859, it was not until the early 1930's that heavy fuel oil residues for open-hearth use began to appear on the market. They were cheap; the calorific value was high, and it was not necessary to pass this fuel through the checkers to preheat it. Various plants began to use such oil as an open-hearth fuel. Others used it in combinations with tar, coke-oven, and/or blast-furnace gases. Because of its low calorific value, blast-furnace gas had to be preheated in the checkers. These fuels were cleaner and more dependable than producer gas. The dirty gas house adjacent to the open-hearth shop was no longer needed, and

Jan 1, 1961

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By F. J. Longworth

FoR a number of years an intensive study has been made to improve the blast-furnace practice at Copperhill not only as to cost% but to provide a good grade of gas for the acid plants. This study took us back to the fundamentals of successful pyrite smelting; namely, a blast furnace working on a clean sulfide ore, free from fines, and the use of quartz high in silica as a flux. In 1919, the quality of the flux was improved and its effect on the metallurgy was very marked. To improve the practice further, it was necessary to work out some method of treatment for the sulfide fines and the siliceous and refractory ores, other than in the blast furnace. A series of milling tests indicated that these products could be successfully treated by differential flotation, and in 1922 plans were made and a flotation plant built. It was estimated that the flotation plant would deliver to the smelter 40 to 50 tons of concentrates per day; the problem was what to do with these concentrates. It was out of the question to attempt to smelt them in a blast furnace because of the dust losses and because our practice demands a charge free from fines for satisfactory operation. There is no custom smelter in the vicinity to which concentrates may be sold, pending the time when the tonnage will be sufficient to warrant roasters and a reverbatory furnace. Sintering and nodulizing were investigated but neither method fitted into our scheme of metallurgy. A close study of the converter practice was then made to see if some method could not be evolved to smelt this tonnage of concentrates in a converter without preliminary treatment. At that time, the converter installation consisted of two 12-ft. Great Falls converters, which were handling 12 to 14 per cent. matte. The heat balance of the converters working with 12 to 14 per cent. matte was more than sufficient to smelt the contemplated tonnage of concentrates but the mechanical difficulties of feeding fines into the Great Falls converter made the use of this type of converter impractical. While there was no opportunity to experiment with the Pierce-Smith converter, equipped with a Garr gun, theoretically it seemed practical

Jan 1, 1925

By J. A. Herbst, G. A. Grandy, T. S. Mika, D. W. Fuerstenau, G. D. Gumtz

As a basis for interpretation of grinding behavior, the discretized batch grinding model is briefly presented and described, with solutions of the resultant equations for linear systems. Techniques for obtaining relevant experimental data are discussed for first order grinding systems, with methods for estimating other systems1 parameters from these data. Computer methods are described for conducting a sensitivity analysis which can be used to obtain an improved estimate of the system parameters. Examples of the use of the computer in conjunction with the grinding model for the simulation of batch grinding, locked-cycle grinding, and closed-circuit grinding are presented.

Jan 1, 1969

By C. Jardine, D. Freudenreich

The system concept is to minimize costly unscheduled equipment breakdowns by replacing components earlier than their life expectancy. Periodic unit services are scheduled according to preset constraints. Service sheets are generated by matching a job and component master listing based on assigned cyclic component lives. The system can account for all man-hours reported, and history information can be selectively retrieved. By reducing unscheduled equipment shutdowns, this system allows for better manpower utilization and an overall improvement in equipment reliability and availability.

Jan 1, 1982

By E. D. Gardner

AGAIN in 1945, the fourth year of World War 11, the American mining industry met the necessary demand made upon it for metals. Lack of labor prevented full production in some districts; maximum output, however, was maintained with the man power available. Development work and maintenance of mechanical equipment were neglected in favor of immediate production. Drafting of the younger men continued throughout the year, and the loss of personnel to war industries with higher wage rates continued up to "V-J" Day, Aug. 14. Labor shortages were more critical in 1945 than in 1944 though the man-power situation eased for some districts in the last quarter of the year. The trend in mining for the most part was to increase tons per man-shift by continued increased mechanization and refinements in methods and practices; larger equipment was installed where practicable. Labor shortages, together with the current higher wage rates, have advanced mechanization several years ahead of normal progress. The manpower shortage and the employment of inexperienced men had the effect of decreasing the average efficiency of the individual workman, but this condition was largely balanced by improved organization, greater efforts to improve labor relationship, and increased use of incentive pay systems. Safety instruction was emphasized, personnel contacts were increased, and more frequent foremen meetings were held to clarify contract agreements. Many of the large companies maintained schools to train green workmen.

Jan 1, 1946

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 9, Article I, of the Bylaws of the Institute (see page 61 and following pages). During 1934, sundry amendments were made for the purpose of improving

Jan 1, 1939

By Ferris E. Sainsbury

As most mining companies utilize contractors rather than in-house drilling departments, it is difficult for most mining engineers to become familiar with drilling techniques This chapter will explain the various drilling options available to the mining industry through the services of a drilling contractor. It will also suggest improvements in program planning and specification writing by the mining company representatives to enable them to derive maximum benefit from the contractor.

Jan 1, 1979

By Donald A. Cumming

Since the first major mine development, the company has continually looked for ways of improving drifting methods. The planned increase in production to 60,000 tpd, and the lack of trained personnel, requires new development methods to maintain this high production rate. In order to finish the drifting on the 2015 and 2075 levels, a total of 59,000 ft is required, or two years at the present rate.

Jan 4, 1972

By L. L. McDaniel

During the past few years a nuinber of improvements in smelting and power equipment have been made at the Douglas smelter of the Phelps Dodge Corporation at Douglas, Ariz. In the summer of 1935 work was started on the first unit of a new reverberatory waste-heat boiler plant which ultimately was to furnish steam for a modern high-pressure power pIant. A second reverberatory waste-heat boiler unit

Jan 1, 1944

By E. D. Gardner

The tide of increasing demand for metals turned during early 1949, with resultant lower prices. The production of the principal metals was less than in 1948. The problem of high unit costs, however, was held over from 1948. With the lower prices for metals, greater efforts are being made to reduce operating costs. The labor supply was adequate during the latter half of the year in most districts. The force has been reduced at most mines; some mines were idle during part of the year because of strikes, and others ceased operations on their own account. In the main, labor efficiency increased during the year in underground metal mines. Efforts are being made generally to improve labor relations. Green men hired in the time of the scarcity of skilled miners are becoming better trained. The supervisory personnel of most mines is cost conscious, and the planning of operations has been improved. Overhead costs are being scrutinized. The trend toward mechanization underground continued strong. Mining technology rapidly is becoming a problem of handling materials. Surface miners, underground miners and miners of metals, nonmetallics, and coal can learn much Gardner from each other. A mine, however, may become overmechanized. The capital charges against new equipment may exceed the saving in labor costs where sufficient daily tonnage is not handled.

Jan 1, 1950

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion- equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control.

Jan 3, 1954

By P. J. Connors, William J. McCormick, F. B. Olender, Jerome F. Sheldon, Donald T. Mylar, Edgar T. Gregory, Owen S. Roberts, H. Colijn

A quiet revolution has taken place in the conveyor belt industry. Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry. Formerly the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Monofilament rayon, with desirable elongation and elastic properties, was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon.

Jan 3, 1972

By O. R. Wagner, R. O. Leach, H. W. Wood, C. F. Harpke

PAN AMERICAN PETROLEUM CORP.TULSA, OKLA. CASPER, WYO A field test has been made in which additional oil recovery was obtained from a previously-waterflooded "oil-wet" sandstone reservoir. This recovery improvement was accomplished by adjusting the reservoir wettability through chemical treatment of the flood water. The test was made in the Muddy sand of the West Harrisburg Unit, Neb. The chemical used, sodium hydroxide, was injected as a slug of dilute caustic solution through a water-injection well. The natural wettability of the reservoir and the chemical requirements for reversing wettability were determined in the laboratory from contact-angle studies using field water and oil samples. Laboratory flood tests with a synthetic system had shown that reversing the wettability of an oil-wet consolidated core would lead to improved oil recovery. The field performance indicates that the mechanism by which increased oil retovery is obtained in the field is the same as that observed in the lahoratory. Laboratory studies indicate that higher ultimate recoveries and decreascd water-injection requirements result when the adjusting agent is added early in the life of the flood. However, a previously waterflooded area was intentiorzally chosen for the field test so that unambiguous conclusions could be made about the effects of chemical injection on wettability and the extent of oil-recovery improvernent afforded by wettability reversal. Forces existing at the fluid-solid and fluid-fluid interfaces in a porous medium have an important effect on oil recovery during a water flood. Modifying these interfacial forces in the reservoir to improve oil recovery has been the object of much research. Several papers' ' have discussed the use of surfactants to lower the water-oil interfacial tension. This paper describes work concerned with improving oil recovery by modifying the forces at the fluid-solid interfaces— that is, by changing the preferential wettability. An earlier paper: presented evidence to show that some reservoir systems could be changed from preferentially oil-wet to preferentially water-wet by the action of simple chemicals added to the water to increase waterflood oil recovery. The process was attractive for further study because it used only inexpensive chemicals and because it called for a gross "wettability reversal" rather than for a precise adjustment. The present paper is an extension of the earlier work. Laboratory flow tests were made using treated water and oil in a consolidated core to determine the amount of additional oil recovery and the producing performance which might be expected from reversing the wettability of an oil-wet reservoir during a flood. A contact-anglc study using water and oil from the Muddy "J" sand of the Harrisburg field, Banner County, Neb., indicated the reservoir to be preferentially oil-wet and susceptible to wettability reversal through chemical injection. Based on these studies, a field trial of wettability-reversal water flooding was initiated. in the Harrisburg field. The primary purpose of the trial was to determine if wettability-reversal flooding would improve oil recovery in an actual field situation. The field trial was also an important test of the laboratory tecnique used to determine the effect on oil recovery of certain wettability manipulation, as well as a test of the contract-angle method of determining reservoir wetra-bility. The paper is presented in two parts. The first part covers the laboratory experiments leading up to the field trial, and the second part covers the field trial. PART I—LABORATORY STUDY The laboratory experiments consisted of displacement tests using an idealized fluid system and of a contact-angle study with crude and water from the Muddy "J" sand of the West Harrisburg Unit, Banner County, Neb. The displacement tests were designed to determine the effects of a particular wettability manipulation, oil-wet to water-wet, on oil displacement in a water flood. The contact-angle measurements were made to determine the natural wettability of the reservoir and to determine if beneficial wetting changes could be brought about by a chemical addition to the flood water. PROCEDURE DISPLACEMENT TESTS The displacement tests were perfornled in a consolidated sandstone core using a refined oil and water. The wetting properties of this system could

By H. J. LONGMORE

MORE improvements have probably been made in the diamond-drill field in the past decade than were accomplished in the entire prior period since diamond drilling was discovered in 1864 by a French engineer named Leschot. True, machines were improved, and new accessories were adopted from time to time up to 1929, but no radical changes were made. The basic principle instituted during the early years of the industry were still in use in 1929. At that time, practically the only diamonds used were "black diamonds" or "carbon." These came from Brazil through a rather round- about route, and by the time they got to the drilling trade their cost was excessive-$175 per carat and even higher at the peak. Perhaps because of this. or perhaps because of increased competition, the industry sought ways to reduce expenses even in the face of constantly increased labor costs due to higher wages and reduction in hours worked. The solution seemed to rest in two things-use of a cheaper cutting medium to replace the carbon diamond and the development of new machines to drill faster and thus produce more hole per shift of operation.

Jan 1, 1940

By Erkki Laurila

INVESTIGATION of the methods of analyses for magnetite and ilmenite in the Otanmäki iron-titanium ore and respective mill products has resulted in certain improvements in the methods conventionally employed. The outcome of the investigations is summarized as follows: 1-Development of a diamond-drill core analyser for the determination of magnetic susceptibility of drill cores containing magnetic minerals. 2-Development of a magnetite-ilmenite analyser for pulverized products. 3-Development of a potentiometric method of chemical analysis for the determination of iron, vanadium, and titanium in succeeding steps from one test sample. 4-Proposal for a continuous and automatic magnetite assay method.

Jan 9, 1951

By J. H. Wernick, J. E. Kunzler

HIGHLY pure metals are needed for low-temperature electron transport studies in progress. Recent improvements in purification techniques, such as zone refining, have made it possible to obtain metals with improved purity. For some metals, the improvement has been to the extent that ordinary analytical techniques are inadequate and special methods are needed.1 For other metals purification is more difficult, so that simple but rapid analytical methods are desirable as an aid in evaluating the effectiveness of purification procedures. Furthermore, it is desirable to be able to determine the impurity level of the sample or ingot with the minimum of physical disturbance of the material. In order to aid in the preparation of purer metals, techniques involving the measurement of electrical resistance at liquid-helium temperatures have been devised for studying impurity distributions in zone-refined ingots and other bulk samples without destroying the ingot or its geometry. The method yields information on the variations in purity along the length of the ingot or sample and provides a measure of the overall purity of the material. Compared with ordinary analytical methods, the resistivity method is rapid, sensitive, and does not require significant physical disturbance of samples with reasonable shapes. It has the disadvantage that resistance measurements are not specific, i.e., they do not identify the impurity. However, this disadvantage is offset by the advantage of being able to establish a measure of the overall purity so far as electrically active" impurities are concerned. METHOD AND ITS BASIS The method is based on the well-known fact that the resistivity, at Liquid helium temperatures, of a reasonably pure metal containing no regions with additional phases decreases with increasing chemical purity or a decrease in the number of physical defects. It is convenient to separate the total resistivity into three parts: where is the resistivity due to the scattering of the conduction electrons by the lattice vibrations or phonons, p is the contribution due to physical defects, and originates from the effect of chemical impurities in the metal. Insofar as Matthiessen's rule is obeyed,2 pphys and pchem are independent of temperature. Except possiblyin the very purest metals, ptherm is negligible at liquid helium temperatures and For zone-refined metals, which normally are well annealed and consist of large grains, at the chemical purity levels thus far attained the available data indicate that pphys is negligibly small or at least constant throughout the ingot. Assuming that the effect of physical defects is negligible for isotropic metals, This assumption appears consistent with most of

Jan 1, 1959

By J. P. Martin, A. H. Geisler, J. H. Crede, E. Both

The investigation of a 50 pct Co alloy was undertaken to determine whether there was any direct correlation between the structure and properties of Co-Fe alloys which were given various magnetic heat treatments. The magnetic anisotropy and texture of the 0.002-in. cold-reduced 98 pct material tend to decrease and change in nature with increasing temperature of the recrystallization anneal. Annealing samples in a magnetic field had little effect on either the magnetic properties or texture. However, cooling them in a magnetic field greatly improved their magnetic properties. THE beneficial influence of a magnetic field applied during the heat treatment of certain soft magnetic materials has been known for a long time. Early work showed that the presence of a magnetic field of a few oersteds during the heat treatment of Fe-Ni alloys will cause a large increase in maximum permeability. A pronounced increase in the residual induction which is produced by the magnetic anneal causes the hysteresis loop to approach the shape of a rectangle. Such results are beneficial since the desired properties are high permeability, high induction at maximum permeability, high residual induction, and low coercive force. More recently Libsch and coworkers1 studied the effect of magnetic annealing on the hysteresis properties of a series of Co-Fe alloys prepared from powders. They observed good response for the 35 and 50 pct Co alloys but little response for the 42 pct Co alloy. They pointed out that this was somewhat surprising since the 42 pct alloy has a high linear magnetostriction and zero crystal anisotropy and similar conditions in Fe-Ni alloys give excellent response to magnetic annealing. They found optimum properties to be at the 50 pct composition with residual induction, Br = 19,000 gauss and coercive force, Hc = 0.68 oersteds after the magnetic anneal. Before the magnetic anneal these values were B, = 12,600 gauss and Hc = 1.15 oersteds. The optimum treatment consisted of cooling from above the y-a transformation temperature to 900°C in a field of 20 oersteds, holding 11/2 hr at 900°C, then cooling at a rate of 20° to 25°C per min in the field to below 230°C. Cooling rate mainly affected coercive force with the value decreasing from 1.09 to 0.88 oersteds as the rate was increased from 3° to 48°C per min. Cooling from 1020" to 900°C in a field followed by further cooling to 230°C without the field gave properties decidedly inferior to those for samples annealed with the field applied throughout the cooling. They concluded that to get the best properties the samples must be cooled in a field to a threshold temperature above which the alloy is plastic enough to be affected by magnetostriction. In this respect the holding temperature must be high enough so that the alloy exhibits good plasticity to permit the optimum orienting of magnetic domains by relaxation of magnetostriction. In contrast, the holding time was of less significance for there was little improvement when the time exceeded 1/2 hr. The improvement in properties effected by magnetic annealing has usually been attributed to the establishment of a domain texture caused by the "freezing in" of magnetic strains. On the other hand, Smoluchowski and Turner2,3 apparently found that a magnetic field applied during recrystallization could alter the crystal texture. If this effect is real, improved properties would also be expected when

Jan 1, 1954