Search Documents

Such are the rigors of climate and topography of western Tasmania, that much of the area has remained uninhabited. The mountains, rising to peaks above 5000 ft high, receive the winds out of the west and precipitate 110 in. of rainfall a year on this coast. The drenched forests have a primordial look with such unfamiliar trees as the tru-sassafras, blackwood, cheesewood, ti tree, and man tree ferns. Prospectors speak of the "horizontals," trees which, in the dense foliage, grow out flat. When the explorer climbs over them he does not come back to the ground but continues forward on dense vegetation with the ground many feet below. Gold was discovered by the intrepid prospectors of the late nineteenth century and stamp mills were erected in the vicinity of Zeehan and Queenstown. At Mount Lyell, mining began for gold in the ironstone capping. The familiar story, of course, is that copper was found beneath the gossan and it was this mineralization that lead to permanent mining operations. Two companies began mining at Mount Lyell and their history from 1893 to 1902 was marked by an unreasonable competitiveness, human perversity and technical difficulties. The North Lyell and Mount Lyell companies were mining copper ores within one mile of each other separated only by a ridge. Each company built its own railroad and harbor. For six years of struggle both companies tried to work out the metallurgical problem which was the key to profit. Although they didn't know it, the two ores were complimentary and could have been smelted together. North Lyell ore was strong in silica and weak in iron, whereas Mount Lyell was fortunate in having a first-class metallurgist in Robert Sticht, from Brooklyn, N. Y., who in 1902 successfully achieved pyritic smelting without the use of carbon fuel.

Jan 10, 1964

By S. C. Geol, C. H. Page

INTRODUCTION Mining at Mindola Mine, Rokana Division of Nchanga Consolidated Copper Mines Limited is the deepest on the Zambian Copperbelt. Mining extends to 1150 metre depth so far and the present plans extend to 1500 metres, although reserves exist below this level. Mindola Mine is the major producer of copper/cobalt ore at Rokana Division and produces approximately 200,000 tonnes of copper/cobalt ore per month. A standard open stoping method is the only method used for mining with minor variations in positioning drilling drives and other development, figure 1. The standard main haulage interval is 75m but in flat dipping areas the full stope height is split into two or three panels. In 1970 severe mining problems were experienced when mining deeper than 850111 below surface. The main problems included: - Heavy support requirements in drilling drives near stope face. - Premature closure of blast holes necessitating pre-charging of the holes with explosives immediately after drilling and well before the day of blasting. - Severe bumping and spitting due to rock movements on drive surfaces and remotely within the rock mass under high stress. - Low mining efficiency due to dilution from the waste hangingwall. - These stress related factors also caused some premature detonations of precharged but unprimed blast holes which became a serious safety hazard. A number of alternatives have been considered to overcome these problems. A search for leas sensitive explosives to avoid the premature detonation problem has been partially successful, however, the need for a method of reducing stress levels at the mining face is still considered essential as the mine goes deeper. This paper describes experiments with Regional Support Pillars as a method of reducing stresses at the mining face.

Jan 1, 1981

By Tomoyuki Moritani, Atsuyuki Mizuno

A concentration of manganese nodule varies areally from 0 to 30 kg/m2 in the central-eastern deep sea bottom of Central Pacific Basin with depth of 5,600-5,900m, but generally it is low, mostly of the abundance order from 0 to less than some kilograms per square metres through the bottom. A high concentration over about l0kg/m is localized to the northwestern basin, besides "St. 414 Deep Sea Hill" and “GH 76-1 Trought”, and also it is likely related with the substratum of deep sea clay. Nodules are tentatively classified into nine types of Sr, SPr, SEr, Db, Ss/SPs, ISs, IDPs and V, in terms of morphology and surface feature. The types may be related with internal structure, nuculeus, mineral composition, chemical composition, occurrence and areal distribution, and might have resulted from various environmental factors of nodule genesis. The abundance of nodule at each station shows the interesting relation with acoustic records by 3.5KHz and seismic reflection profilings. In both the records, thick transparent layer over about 45m thick yield neither any nor significant amount of nodule. The layer less than 45m relates with abundant nodules up to 30kg/m2, though it yield also very little nodule in some cases. The relation suggests that the formation of nodule most likely could be related with the accumulation rate of the post-middle Eocene sedimentary sequence to some extent and also with other controlling factors. The relation can lead us to the tentative delineation of distribution of nodule deposits in the area. The comparative-consideration with the deposits in GH 74-5 area, just east- ward of the present area, shows the areal peculiarity of nodule genesis in deep sea bottom. The results of chemical analyses will be discussed elsewhere.

Jan 1, 1976

By G. Ansel, J. O. Betteron

THE PURPOSE OF THIS PAPER is to give a brief picture of present day magnesium rolling practice, to elaborate on laboratory and development rolling experiments; and finally, to discuss the possible Future rolling of magnesium. The present production practice is so varied between various mills that it can only he concluded that no single producer is now using a process that is outstandingly superior to others. In view of this, only the general features of present day production practice have been presented and attention is focussed on the results of laboratory find development rolling of magnesium-base alloys as indications of the Future trend of magnesium rolling. MAGNESIUM ROLLING LITERATURE The literature relating to magnesium rolling is divided into three groups: the deformation mechanisms of the hexagonal magnesium crystals, the metallurgical aspects and laboratory type experiments in rolling, and finally, the articles on production rolling methods. This literature was reviewed and is summarized below. In the first group of references, the existence of basal slip in magnesium single crystals was shown by Schiebold and Siebel1 and of {102} twinning by Mathewson and Phillips2, Schmid3 predicted and partially established {101} slip at hot working temperatures. Bakarian and Mathewson4 confirmed the above and eliminated {101} twinning as a probable deformation mechan-

Jan 1, 1948

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By Paul Billingsley

THE development of the North Lily ground, which lies in the East Tintic district, Utah,. about half a mile northwest of the famous Tintic Standard mine, was undertaken by the International Smelting Co. on purely geological reasoning. The geologic theory on which this work was based resulted from several years' intensive study of the East Tintic district by the geological department of the International Smelt-ing Co., who were, during this period, indebted to many for valuable suggestions that were adopted and became part, of the gradually maturing concept. For example, E. J. Raddatz, president of the Tintic Standard Mining Co., first called attention to the significance of rhyolite alteration; J. W. Wade, assistant manager, contributed greatly to our knowledge of the great Tintic Standard orebodies; and so on all along. the line. In short, the ultimate theory embodies the aggregate experience and thought of all those most familiar with the area in question. The problem in brief was this: is the Tintic Standard deposit an isolated occurrence of ore, or are other ore deposits to be found in the vicinity? If the latter is the case, where can these others be looked for? The difficulty of the problem lay in the fact that most of the area is covered by rhyolite; beneath which lies the limestone in which the orebodies occur; so that the available evidence as to the structure of the formations, and, their mineralization; is of the slightest. The sav-ing features of the case, by means of which it proved possible to solve the problem, are three in number first, the rhyolite is pre-mineral and hence has been exposed to alteration by the mineralizing agencies; second, certain persistent dikes and fissures are con-tinuous through the rhyolite into the limestone below; and third, the extensive underground workings of the Tintic Standard gave a good basis for study of the sub-rhyolite structure and the occurrence of ore. The rhyolite overlies the Tintic Standard orebodies, and over them shows a large patch of brownish altera-tion. This patch proves to be due to chloritization and sericitization, which has spread out from certain zones of dikes, pebble-dikes and fissures. The dikes are com-posed of a light fine-grained rock which has been altered to an aggregate of quartz, alunite, and magnetite. They can be traced southwest to a common center in Big Hill, the entire mass of which is composed of the same material. The pebble-dikes, which consist of a mass of rounded pebbles, mainly quartzite, in a matrix ranging from the same quartz-alunite-magnetite rock as above to almost pure vein quartz, are closely asso-ciated with these light dikes, but in general extend farther northeast. They thus represent a specialized phase of the intrusive action of which Big Hill is the center. The brown chloritized rhyolite, then, is an alteration product due, in all. probability, to emana-tions closely associated with this phase. Since it coin-cides geographically with the Tintic Standard area of highly altered limestone, with its many great ore-bodies, it has been concluded, that it is the expression in the rhyolite of activities which have also altered and mineralized' the underlying limestone.

Jan 4, 1927

By D. S. Flett, D. W. West

The solvent extraction of chromium 111 has been studied for the system Cr 111, H,SO., H,O/RNH/RNH., xylene, where the primary amine used was Primene JMT. Rate studies have shown that extremely long equilibrium times are required, ranging from 1 hr at 80°C to 20 days at room temperature. Heating the solution prior to extraction increases the rate of extraction. The variation in the amount of Cr 111 extracted is an inverse function of the acidity of the aqueous phase. Thus, the slow rates of extraction appear to be connected with the hydrolysis of the Cr I11 species. Extraction isotherms for the extraction of Cr 111 have been obtained for two sets of experimental conditions, namely at 60°C and for a heat-treated solution cooled to room temperature. The separation of Fe 111 from Cr 111 and Cr 111 from Cu 11 in sulfate solution by extraction with Primene JMT has been studied and shown to be feasible. A survey of the literature relating to the solvent extraction of chromium showed that, although many systems exist for extraction of Cr VI, only a very few reagents have been found to extract Cr 111. The extraction of Cr III by di-(2-ethyl hexyl) phosphoric acid has been reported by Kimura.' A straight-line dependence of slope —2 was observed between log D,, and the log mineral acid concentration at constant extractant concentration. Since the slope of this plot reflects the charge on the ion extracted, it must be concluded that a hydrolyzed species of Cr III is being extracted. Carboxylic acids generally do not form extractable complexes with Cr III but di-isopropyl salicylic acie does extract Cr 111. Simple acid backwashing of the organic phase, however, failed to remove the chromium. Similar difficulty in backwashing was found by Hellwege and Schweitzer8 in the extraction of Cr I11 with acetyl-acetone in chloroform. The extraction of Cr 111 from chloride solutions by alkyl amines has been reported4-' but the maximum amount of extraction achieved in these studies did not exceed 10%: From sulfate solutions, however, Ishimori" has shown that appreciable amounts of Cr I11 were extracted by amines. The amines used were tri-iso-octyl amine, Amberlite LA-1 (a secondary amine, Rohm & Haas) and Primene JMT (primary amine, Rohm & Haas). The efficiency of extraction with regard to amine type was primary>secondary> tertiary. Appreciable extraction of Cr I11 was recorded for Primene JMT as the aqueous phase acidity tended to zero. The major difficulty with Cr I11 in solvent extraction systems stems from the nonlabile nature of the ion in complex formation. This accounts for the slow rate of extraction generally experienced and the difficulty encountered in backwashing the Cr I11 from the organic phase in the case of liquid cation exchangers. Consequently, the possibility of extraction of Cr I11 as a complex anion is attractive since the backwashing problems should be minimized in this way. From published data, it appeared that the extraction of chromium from sulfate solutions of low acidity by primary amines afforded the best chance of success for a useful solvent extraction system for Cr iii This paper presents the results of a study of the extraction of Cr I11 from sulfate solution by Primene JMT and examines the application of such an extraction procedure for the recovery of chromium from liquors containing iron and copper. Experimental Chromium solutions were prepared from chrome alum in sulfuric acid and sodium sulfate so as to maintain a constant concentration of sulfate ion of 1.5 molar. Solutions of Primene JMT were prepared in xylene and the amine equilibrated with sulfuric acid/sodium sul-fate solutions, of the same acidity as the chromium solution, until there was no change in acidity between the initial and final aqueous phases. The solutions of Primene JMT conditioned in this way were then used for the equilibration experiments. Equilibrations at 25°C were carried out in stoppered conical flasks shaken in a thermostat; equilibrations at all other temperatures were carried out in stirred flasks in a thermostat. After equilibration, the phases were separated and analyzed for chromium. In the tests on the rate of extraction, small samples of equal volume of both phases were withdrawn from time to time and the chromium distribution determined. The chromium analyses were carried out either coloi-imetrically using diphenyl carbazide, or volu-metrically using addition of excess standard ferrous ammonium sulfate and back titration of the excess iron with potassium dichromate. The oxidation of Cr 111 to Cr VI in the case of the raffinate solution was effected by boiling with potassium persulfate in the presence of silver nitrate and, for the backwash solution, by boiling with sodium hydroxide and hydrogen peroxide. Results Preliminary experiments indicated that extraction results were effected by the age of the chromium solution, higher distribution coefficients being obtained with solutions which had been allowed to stand for some time. Consequently a stock solution of chrome alum, 10 m moles per 1 Cr I11 in 1.4 M Na,SO,/O.l M &SO,,

Jan 1, 1971

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.' Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph' (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,' have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

By H. M. St. John, T. Rynalski, G. K. Eggleston

Maintaining a satisfactory structure in brass and bronze castings has always been a foundry problem of great practical importance. While metallurgists and scientific investigators have not entirely ignored this matter, it has received less of their attention than has been given to iron, steel and the wrought copper and aluminum alloys. Investigation in this field has probably been discouraged to some extent by the complicated nature of the alloys involved. Hundreds of alloys are in more or less common use, most of them containing copper, zinc, lead and tin in widely varying proportions. They also contain appreciable percentages of iron and antimony as impurities, and often phosphorus, which has been added as a deoxidizer and fluidifier. Small amounts of sulfur are usually present. It is not uncommon to find nickel, sometimes in rather substantial quantities. Traces of other metals are frequently present. So complicated and variable a mixture obviously offers difficulties in any investigation of the various factors that influence the structure and other properties of the casting. Incipient Shrinkage Bolton and Weigandl have called attention to a type of structure characterized by intercrystalline fissures and large dendritic crystals which are frequently tarnished to an orange or reddish brown color. This intercrystalline porosity they term "incipient shrinkage" and attribute to the presence of carbon monoxide in the atmosphere under which the metal was melted. The defective structure to which Bolton and Weigand refer has become a brass-foundry problem of major importance, because it occurs with distressing frequency in leaded brasses and bronzes when these are melted in a neutral or reducing atmosphere. Since the electric furnaces, now coming into general use in brass foundries, normally operate with such an atmosphere and, in fact, depend upon it in part

Jan 1, 1930

By James J. Olson, Richard A. Dick

Blasting practices have shown a recent trend toward larger blastholes and larger burdens and spacings, although some operators, after reconsidering the situation have gone back to smaller blasthole sizes. The greater pull-down capabilities of larger drill rigs and the greater bearing strength of large diameter drill bits give penetration rates for large diameter blastholes approaching, and sometimes exceeding, penetration rates for smaller holes. In practically all cases, large diameter holes can be drilled more quickly and cheaply, based on volume of hole, than small diameter holes. The industry's shift to dry blasting agents and slurries, products which perform more dependably and efficiently in larger diameters, gives an additional advantage to larger boreholes.

Jan 3, 1972

By Milton H. Fies

THE Alabama Power Co. operates its Gorgas mine in Walker County, Ala., immediately adjacent to its steam plant. The coal mine property consists of some 19,000 acres of fee and mineral ownership lands, and all of the production from the mine-approximately 2500 tons per day-is utilized at the company's adjoining steam plant. The company is presently considering the purchase of additional acreage adjoining its present holdings which acquisition will almost double its reserves. The coal is transported from the mine over a short railroad spur in the company's own equipment, either directly to one of the large plants at Gorgas or to a storage pile. The longest haul is about 1 1/4 miles.

Jan 12, 1950

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.' The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

?ADAIR, ARTHUR C., Corp 4th Co., 1st. Training Bat., 154th Depot Brigade. ADAMS, HENRY, Major: Chemical Warfare Service. ARLUCK, A. A Headquarters, 1st Corps of Artillery. ASKIN, THOMAS B. H Ensign. BANKS, H. R., 2d Lieut Canadian Engineers. BAYLESS, G. E. S Supply Dept. U. S. Submarine Base. BELL, L. R Co. C, 302d Engineers. BELLIS, ARTHUR E., Capt Ordnance Reserve Corps. I BIRRETT, HOWARD, Lieut., Aviation Section, U. S. Signal Corps, Ellington Field. BOISE, PAUL T 2d Regiment, 24th Squadron. ?BRADLEY, CLARENCE I Convois Automobile Section 585. BROWN, GEORGE M Co. G lot Engineer Replacement Regiment. BUCKINGHAM, ALBERT U. S. S. " Coronet," S. P. 194, Section Base No. 7. BURNS J. J Co. 1-B, E. R. O. T. C. BURT, Co. B, let Engineers Replacement Regiment. ||BYERS, WHEATON B., 2d Lieut Ordnance Dept. CANTON, WILLIAM R., Sgt Headquarters Co., 80th F. A. CARSON, JOSEPH A., Capt A.S. S. R. C.' CHAPMAN, LEWIS C. Corp 29th engineers. CHETNEY, P. C., 2d Lieut 15th Bat. Headquarters Co. CHEVRILLON Louis French Red Cross. CHIDESTER, W. B., 1st Lieut 24th Machine Gun Bat. CHURCH, JOHN L., Capt 308th Engineers. CLAGHORN, D. MONTGOMERY, 1st Lieut 45th Engineers. CLAQHORN, JAMES L., Lieut Aviation Section, Signal Corps. CLARKE, ALEXANDER F U. S. Naval Aviation Service. COMINS, WALDO H. Ca t 41st Co., 164th Depot Brigade. COOK, FREDERICK A., Capt., Engineer Reserve Corps, Asst. to Div. Engr. 79th Division. COOPER, CLAUDE H. Capt C. A. R. C., 50th Artillery. COPELAND, N. R., Lieut. ||CORBY H.. G., 1st Lieut Co. D, 109th Supply Train. CORSA, BEAN, Capt Co. D, 612th Engineers. CORTESE, EMILIO Italian Army. COULDREY PAUL S., Corp British Expeditionary Forces. || CRAGIN, RODNEY S Co. E, 115th Engineers. CURRIE, JOHN M., Ca t Royal Engineers. || CUTTING, G. W., 2d Lieut U. S. Reserves, Field Artillery. V DARRINGTON, PAUL N., 1st Lieut U. S. Infantry. DAVIS, ANGUS W., Lieut-Col British Expeditionary Forces. || DAVIS, THORNTON, 1st Lieut 13th Field Artillery. ELAND, FREDERICK A., Major Engineer Reserve Corps. DOUGLAS, JAMES $ American Red Cross. DOVE, D. R., Candidate 21st Training Battery, F. A. C. O. T. C. Dover JAMES J 6th Co. C. B. DOWS, DAVID,Capt Coast Artillery, Officers Reserve Corps. || DRAKE, M. 6., 2d Lieut Headquarters Co., 325th Infantry. I || EMMERSON, E. Roy British Navy. EVERIT, RICHARD STURTEVANT Heavy Artillery Officers' Training Camp.

Jan 1, 1923

By W. O. Hotchkiss

RECOVERY and profits in the mining business do not go hand in hand. Some part of an orebody can usually be recovered at a lower cost per ton than the whole orebody or a higher proportion of it. Similarly, the total of the profits that may be made from mining an orebody is in itself not a true measure of the value of the business. The yardstick for money value should be present worth, and this is particularly so for purposes of com-parison. A simple example, well within the bounds of practicability, illustrates these points: Assume a mine to have known ore reserves of 4,000,000 tons. The ore is of uniform grade but is so situated that 1,000,000 tons could be mined more cheaply than the remainder. Present operations are on the basis of complete recovery of the ores. Output is 100,000 tons per year at a profit of $1 per ton. It is estimated that the 1,000,000 tons of readily accessible ore could be mined at the same production rate but at a profit of $2 per ton. For an output of 100,000 tons each year at a profit of $1.00 per ton, the mine will have a life of 40 years; will produce $4,000,000 of total profit, and, at Hoskold rates of 8 and 4 per cent, will have a present value of $1,104,690. If only the easy one-quarter of the ore is considered, with an output of 100,000 tons each year, at a profit of $2.00 per ton, that part of the mine will have a life of 10 years, will produce total profits of $2,000,000, and at rates of 8 and 4 per cent will have a present value of $1,224,800. . Under conditions such as these, then, one-quarter of the reserve ore promptly mined is worth some 10 per cent more than the entire reserve would be on an average basis extending over the longer period. Assume further that one-half, or 2,000,000 tons, of the reserves could be promptly mined at the same yearly rate of 100,000 tons at a profit of $1.50 per ton. Then this part of the mine would have a life of 20 years, would produce total profits of $3,000,000, and would have a present value of $1,320,630; approximately 20 per cent greater than for the whole ore-body on an average basis for the longer period.

Jan 1, 1936

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

By H. F. Silliman, Daniel R. Hull, Earl W. Palmer

THE brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that [ ] contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6 ¾ in. wide by 1 in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. [ ] In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breaking rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause-however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

By Enrique Hauser

Discussion of the paper of ENRIQUE HAUSER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 521 to 534. GEORGE A. BURRELL, Pittsburgh, Pa. Mr. Hauser determined the influence of inert gases on the properties of fire-damp mixtures, and one might take some issue with his work on the effect of hydrogen, on those mixtures. It is valuable information to have, but as far as the practical application of it goes, it is not of much significance, because one does not find it in mines, at least not in any appreciable amount. The same Fig. 1.-APPARATUS FUR DETECTING COMBUSTIBLE GASES IN AIR. thing can be said of ethylene. Ethylene is formed in considerable quantities as a product of heat reaction, but normally, in the coal mines, as a result of a great many analyses we have made at the Bureau of Mines, we cannot say that ethylene is a combustible gas found in the fire-damp in coal mines.

Jan 5, 1916

By R. E. Ogilvie, A. R. Kaufmann, S. H. Gelles

The solid-solubility limits of iron in beryllium were determined between 850o and 1200oC by analysis of differential type multiphase diffusion couples, using an X-ray absorption technique. The maximum value of the solubility limit was found to be 0.92 ± 0.02 at. pct (5.46 wt pet) at the eutectic temperature 1225°C. The solubilities of nickel and beryllium were determined between 900°and 1200°C by the same technique and the maximum solubility was found to be 4.93 + 0.01 at. pct (25.2 wt pet) at the eutectoid temperature, 1065°C. A previously unreported high-temperature phase which decomposes eutectoidally at 1065 °C was found to exist in the beryllium-nickel system at a composition of approximately 8 at. pct Ni (36 wt pet) by diffision-couple analysis. The presence of this phase was confirmed by thermal analysis and metallo-graphic analysis of the structure resulting from the eutectoid decomposition. G. V. Raynor1 has treated the solid solubilities of some of the elements in beryllium on the basis of the "Hume-Rothery" rules2 which have been modified to include ionic size and ionic distortion effects. It was predicted that the solubility of iron and nickel in beryllium should be slightly less than that of copper. The lowering of the solubility, according to Raynor, is due to a more unfavorable relative valency effect and an ionic size effect. Kaufmann and corzine3 have compiled data on the solubilities of elements in beryllium and have discussed them in the light of the Raynor paper. These authors feel that, because the elements having the greatest solubility in beryllium systematically fall in the Group VIII and IB Columns of the periodic table, the electronic structure greatly influences the maximum solid solubility of elements in beryllium. The solubility of iron in beryllium was determined by Teitel and cohen4 as part of the study of the beryllium-iron phase diagram. The determination was carried out by X-ray and thermal analysis and according to the phase diagram presented, the maximum solubility of iron in beryllium is 0.41 at. pct (2.5 wt pct) at 1225oC. However, it is estimated that the uncertainty in the position of the a-beryllium primary solid-solution boundary is about 0.5 at. pct (3wtpct). Losana and Goria3 in studying the beryllium-nickel phase diagram, determined the solid solubility of nickel in beryllium by thermal analysis. They found the maximum solubility to be between 1.65 and 2.65 at. pct (10 to 15 wt pct) at 1240°C. This value decreased rapidly with decreasing temperature. In determining approximate ranges of solubilities for different elements in beryllium, Kaufmann, et al,8 reported a value of between 1.3 and 1.7 at. pct (7.9 to 10.1 wt pct) for the solubility of nickel in beryllium. The value was obtained by metallographic examination of quenched alloys and lattice-parameter measurements. However, the authors also noted a single-phase structure for a 1.7 at. pct Ni alloy (10 wt pct) on cooling from the liquid. This would indicate a higher solubility range than was reported. ~isch,' in his X-ray studies of beryllium-copper, beryllium-nickel, and beryllium-iron intermetallic compounds, reports the disappearance of a second phase (Ni,Be2) in the beryllium primary solid solution at approximately 4 at. pct (20 wt pct). THEORY The analysis of concentration gradients in diffusion couples has proven to be a useful tool in determining phase equilibria.8-14 In this particular study the diffusion couples were chosen to straddle the expected composition range of the phase boundary, then heat treated at a given temperature and the concentration gradient evaluated. The composition of the phase boundary for a given temperature appears at a point of discontinuity of the composition gradient. Examples of typical phase diagrams and the concentration gradients which should be found in such systems are shown in Fig. 1. In the present work, gradients of the form of Fig. l(c) were obtained in diffusion couples made of pure beryllium and two-phase alloys of beryllium with either iron or nickel. The composition at the point where the gradient becomes discontinuous, Cs, corresponds to the solubility limit of either iron or nickel in beryllium. The analysis of the concentration gradients was carried out by an X-ra absorption method developed and applied by Ogilvie and later used by Moll13 and Hilliard.l4 It depends on the fact that the absorption of X-rays by matter is determined by the concentration and type of the various atomic species present. The relationship for the intensity, I, of a monochro-

Jan 1, 1960