Search Documents

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution. Anaconda had done considerable work on the production of sponge iron in 1914 for use as a precipitant of copper from leach solutions. Some success and considerable experilence were attained at the time. indicating that, sponge iron might be successfully made by a modification of the process used in 1914, a batch process in which an iron calcine was reduced by means of soft coke, resulting from noncoking coal, in a Bruckner-type revolving horizontal cylindrical furnace widely used 50 years ago. The coke and calcide formed the bed in the Bruckner furnace, which was rotated at about 1 rpm. The bed was brought to a temperature of about 1800°F by means of an oil flame over the surface. Although results were reasonably satisfactory, they did not warrant full development of the process at that time. A good deal of work has been done in the last 50 years on the production of sponge iron. The objective in some cases has been the production of a precipitant for copper from solution, but the bulk of the work has been done for the production of open-hearth steel furnace stock. The production of an open-hearth stock presents two problems rather than one: first, producticon of the sponge iron, and second, what is perhaps of equal difficulty and importance, conversion of the sponge iron into a form suitable for use in the open-hearth furnace. So far as is known to the writer, none of the sponge iron processes tried in the past have proved to be economically feasible. However, Anaconda had a combination of conditions appearing to justify an attempt to produce sponge iron which would serve for the leach-precipitation-float process. It was thought that the process used in 1914, if changed to a continuous one, might work out satisfactorily. The following favorable conditions at Anaconda justified the investigation: 1—A sufficient tonnage of good grade iron calcine resulting from the roasting of a pyrite concentrate in one of the acid plants, at substantially no cost. 2—Reasonably cheap natural gas. 3-—The fact that there was no need for production of a high grade product. 4— The fact that there was no need for obtaining a consistently high reduction of' the iron in calcine. A small revolving Bruckner-type furnace about 2 ft ID by 4 ft long was set up for early pilot work at the research building. This pilot furnace showed that a satisfactory product could be obtained at reasonable cost. It also indicated a marked advantage in preceding the reduction furnace with a furnace of similar size and capacity for preheating and roasting out any residual sulphur from the feed. The small furnace was operated for several months, various details of the process were worked out. and sponge iron was produced to supply a pilot LPF plant which treated 300 lb of Kelley ore pel- hr. Later a second pilot furnace 5 ft in diam and 12 ft long inside was set up at our reverberatory furnace building. This furnace confirmed the data of the small furnace and gave a basis for design of the final plant. At Anaconda a pyrite concentrate, running about 48 pct S, is recovered from copper concentrator tailings by flotation. This concentrate is roasted to sulphur of 3 pct or less at the Chamber acid plant. The iron calcine contains about 57 pct Fe and 18 pct insoluble. The iron calcine feed, as mentioned before, is re-roasted and preheated in a reroast furnace preceding the reduction furnace. Both are of the Bruckner type. The reroasted calcine is fed into the reduction furnace at 800" to 1000°F along with 30 pct slack coal. In the feed end of the furnace the volatile is burned from the slack, giving a soft coke which readily serves for reduction of the iron. Hard metallurgical coke will not serve the purpose. since it does not reduce CO readily at a temperature of 1850°F. All indications are that the actual reduction of the iron is accomplished by carbon monoxide below the surface of the bed, which is 30 in. deep at its center. Apparently there is a constant interchange: Fe²O³ + 3CO = 2Fe - 3CO², CO² + C = 2CO Actually iron oxide is reduced by CO at somewhat lower temperature than the 1850 °F used in the process. but this temperature is necessary to obtain a satisfactory rate of furnace production. The furnace atmosphere is generally reducing, and typical blue carbon monoxide flames satisfactorily cover the bed. Gas flames from four 3-in. Denver Fire Clay Inspirator burners are played directly on the bed, which is slowly cascaded by the 1 rpm of the furnace. An excess of coke is necessary to assure maintenance of good reducing conditions in the furnace bed. Part of this coke is recovered for re-use.

Jan 1, 1954

By J. S. Diller

In 1827, chromite was discovered near Baltimore by Isaac Tyson, Jr., who initiated the mining of chrome ore an:! later (1845) .the manufacture of chromium compounds in this country. From 1828 to about 1860 the United States, supplanting Russia, supplied chromite for most of the world. Chrome deposits were found also in California, and the Tyson Company shipped ore to Philadelphia by way of Cape Horn. In 1848, J. Lawrence Smith, an American in the employ of the Porte, discovered large bodies of chromite in Asia Minor. They were developed in 1865 and became the chief source of the world's supply for a number of years. The discovery of the large high-grade bodies in New Caledonia, and later in Rhodesia, with other foreign sources, gives at present an abundant supply for all demands. For a number of years before the great war, the United States produced only a few hundred tons of chromite annually, for local use, but during the war the demand for domestic ore resulted in a production of more than 82,000 long tons of crude ore in 1918, and it was demonstrated that the United States has reserve deposits equal to a war demand of several years' duration. Now that the war is over, the country is conserving its domestic supplies by employing higher-grade but cheaper ore from foreign countries. ChromiUm-bearing Minerals Oxides: Chromite-—chromic iron ore................ FeO.Cr2O3 Picotite—chromic iron ore................. (MgFe)O.(Al,Cr) Chromates: Crocoite—lead chromate................... PbCrO4 Phoenicochroite—basic lead ohromite........ 3PbO.2CrO3 Vauquelinite—phospho-chromate of lead..... 2(PbCu)CrOd.(PbCu)3P2O8 Sulfates: Redingtonite—hydrous chromium sulfate.... Knoxvillitel—hydrous basic sulfate of chromium.............................. Daubreelite-—iron-chromium sulfide (known in meteorites only)...................... FeS.Cr2S3

Jan 1, 1920

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

Henry D. Hibbard, High Bridge, N. J. (Communication to the Secretary): There is one chemical factor which has not been considered in the author's tabulation of tests, but which is none the . less important because it cannot be practically estimated, and that is the element oxygen. This element has been, and probably will continue for some time to be, one of the great causes of the continual discrepancies between the chemical and physical properties of steel. Probably oxygen occurs, in important proportions, only in soft steel, such as that which we are now considering. In this steel its physical effect is to diminish tensile strength and elongation. The percentage of oxygen in the steel, under working-conditions that are as uniform as possible, is likely to vary inversely as that of the manganese, or perhaps, and more probably, it may bear even an inverse geometrical ratio to the manganese-content. At all events, to follow the author's plan, the line representing the loss of strength due to oxygen is probably a curve. Plotted by itself, the line would probably be straight; that is, the decrease in strength would be proportional to the increase in oxygen, but if the results were superposed on the percentages of manganese, they would give a curve, because the percentages of oxygen increase faster than those of manganese decrease. Were the oxygen-line to be developed and added to the diagram, it would seem that the manganese-line should then be straight. Due allowance for the effect of oxygen, therefore, would modify two features of the paper. It would increase the figure for the strength of pure iron from 38,000 to about 45;000 pounds per square inch, and it would straighten out the manganese-curve. The manganese-line in the paper is curved between 0.50 and 0.20 per cent. Above 0.50 per cent. it is straight, which may be ascribed

Jan 1, 1893

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By Ed L. Reed

INTRODUCTION The most efficient development of a mine plan for in-situ leach (solution) mining must be based upon an understanding and application of the basic hydrologic characteristics of the aquifer containing the mineral values. Similar knowledge of the overlying and underlying aquifers is also required. This paper summarizes the hydrologic properties of a ground water system and describes some of the more important conclusions that can be drawn from a detailed hydrologic study. Basic to an in-situ leach mining operation is the flow of fluids through porous rock from place to place. The degree to which these movements of fluids can be predicted and controlled determines to a large extent the efficiency of the ore recovery operation. HYDROLOGIC CHARACTERISTICS The principal hydrologic characteristics of a porous medium (sand, intercrystalline or vuggy limestone, fractured basalt, etc.) influencing fluid flow are: Porosity Permeability Thickness Transmissivity Storage Coefficient Water Table or Piezometric Surface Hydraulic Gradient Briefly these parameters can be defined as follows: Porosity: the void space in a unit volume of rock. Permeability: the ease with which fluid will flow through a porous medium. Thickness: the height of the formation which contributes flow to a well. Transmissivity the product of permeability and thickness. Storage Coefficient. the volume of water released from the reservoir per unit drop in head. Water Table or Piezometric Surface: the level at which water will stand in a well: the top of the zone of saturation in a gravity aquifer; the height to which water will rise above the confining bed in an artesian system. Hydraulic Gradient the direction and rate of dip of the water table or piezometric surface. A properly designed pumping test will provide numbers for transmissivity, storage coefficient and the water table or piezometric surface. Drilling records or bore hole logs provide aquifer thickness data from which permeability can be calculated. Ground elevations applied to measured depths to water enable one to calculate the direction and rate of dip of the water table or piezometric surface. Porosity can be determined from core analyses or density logs; it can be estimated from grain size distribution curves in sands or sandstones and from, microscopic examination of drill cuttings derived from carbonate aquifers. CHARACTERISTICS OF FLUID FLOW The characteristics of fluid flow that are vital to an understanding of leach mining include: Velocity Direction Flow Path Radius of Influence The velocity of fluid flow is of paramount importance in planning and managing a leach mine operation. Velocity is directly proportional to the permeability and hydraulic gradient and indirectly proportional to the effective porosity The permeability determined from a pumping test is an average value for the interval stressed; therefore, the velocity calculated from data derived from a pumping test represents average conditions. Under actual conditions discrete portions of the aquifer open to the screen may have permeabilities several times as high as the average and minimum permeabilities only a fraction as much. An injection front will be irregular to the extent that the reservoir rocks are heterogeneous An important consideration is the direct relationship of velocity to head. A reservoir which would provide a velocity of 0.05 feet per day under conditions of equilibrium would allow fluid flow of 36 feet per day under typical leaching operations, i.e. 12-foot injection head, 12-foot pumping level and 50 foot five-spot pattern. The direction of fluid flow is also vital both inside and outside the mine area. In the pattern area the direction of flow is determined by the geometry of the well field and can be approximated by mathematical modeling techniques. Outside the well field, the direction of flow is influenced by both natural conditions and the degree to which production and injection volumes are balanced. Flow directions (and velocities) are critical to an understanding of leachate excursions and their control.

Jan 1, 1979

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength-temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates. IN most routine experimental work on products and processes, method:; of operation and product evaluation are established from accurately controlled laboratory tests. With particular emphasis on the pelletization of fine iron ore concentrates, standardized procedures of laboratory production and product testing have been established at Cleveland-Cliffs Iron Co. Research Laboratory at Ishpeming, Mich. A program of this nature was used for investigating the agglomeration characteristics of various iron ore concentrates. The factors which control the process were studied and subsequently controlled for these investigations. Pelletizing as applied to iron ore agglomeration involves the preparation of spheroidal masses from a fine moist concentrate, followed by high-tempera-ture firing to produce a final product. The preparation of moist spherorids is generally designated as balling. This produces the so-called green pellets or balls. After, these have been fired they are called pellets. Balling is accomplished by rolling moist concentrates in a revolving drum until small spheroids form by a snow-balling action. These balls are then heated in a shaft furnace, or a modification of this device, to a temperature high enough to cause agglomeration within the individual balls while they descend countercurrent to hot oxidizing gases. By this process the lour strength balls are converted through various chemical and physical-chemical processes into hard pellets. With correct balling and firing, the pellets are strong, resist abrasive action and handling treatments, and provide a suitable blast furnace and open hearth feed. In 1950 Tigerschiold and Ilmoni developed a working hypothesis to explain the formation and stability of green pellets.' Their work was presented on the basis of geologists' discoveries concerning the soil-water system and C. V. Firth's early postulates of green pellet formation.' Fundamental reactions oc-curing within fired pellets have been described by Cooke and Ban, who showed the microstructure changes caused by different firing temperatures." All these investigators have provided scientific clarifications of agglomeration by the pelletizing process and have opened avenues for greater development. Mineral grain growth and ceramic bond formation are the two basic phenomena imparting coherency to particles within a fired pellet of iron ore. Each of these is established by the transfer of thermal energy to the mineral particles. Grain growth mechanisms are chiefly physical reactions wherein smaller particles consolidate into larger ones, with resulting decrease in surface energy conforming with the second law of thermodynamics. Ceramic bond formation is a chemical reaction usually between basic and acid metallic oxides of the gangue and ore minerals. CaO, MgO, A1203, and FeO of Fe3O4, react in varying proportions with SiO, or Fe2O3, to form a great series of compounds or amorphous solid solutions. These product bond iron mineral particles together by a bridging action or by direct reaction with the surfaces of the particles. The result of the grain growth-ceramic bond formations is a consolidated, coherent compact of gangue and iron minerals formerly held together by much weaker bonds of interstitial water and forces common to dry, unconsolidated particles.4 With respect to iron ore agglomeration, these high temperature bonding reactions have been described by Schwartz, who referred to the bonds in sinters," and by Cooke and Ban, who referred to the bonds in fired pellets." The extent of the bonding phenomena and the consequent strength of fired pellets is governed by

Jan 1, 1954

By Stephen H. Stow

A relationship exists between the color and the chemical composition of the pebbles from the Bone Valley Phosphate Formation. Darker-colored pebbles are relatively high in iron oxide and relatively low in calcium phosphate when compared to lighter-colored samples; the brown color of the phosphate pebbles can be correlated with their iron content and the black and gray colors with their organic carbon content.1,3 It was anticipated that the darkness of a phosphate sample might be quantitatively measured by a simple reflectivity test and that the amount of reflected light could be correlated with the chemical composition of the rock, especially with the elements which cause the color and darkness of the Florida phosphates. Twenty-one samples of production grade phosphate rock from Hillsboro County, Fla., were studied. All samples were ground to -200 mesh for reflectivity tests and analyses. All analyses are accurate to well within ±2% of the reported value, except for aluminum and organic carbon, which are accurate to only ±15% of the reported amount. Reflectivity measurements were taken with a model 610 Photovoltmeter for tri-stimulus amber, blue and green, and white lights. Experimental procedures and data are available upon request. Results Table 1 contains linear correlation coefficients (LCC) for the element-reflectance relationships for the samples. The top portion of the table refers to the LCC between the percent of light reflected off the samples and the percent of a given element (or its oxide) as analyzed. In the lower portion of the table the LCC refers to the relationship between the same reflectance data and the chemical analyses which have been corrected on the basis of 0% acid insoluble material (chiefly quartz) in the phosphate rock. Each LCC presented in Table I is computed for the 14 coarser samples exclusive of the seven concentrates since the concentrate samples appear to have anomalous reflectivities upon comparison with the coarser grades. Only the most significant LCC for each element is presented in graphical form. Discussion of Data Iron: [Fig. 1] is a graph of the relationship between iron and reflectivity (LCC = - 0.98). A good correlation with Fe2O3, is expected due to the relationship between the tan (or brown) color and the abundance of iron oxide, the principal mode of occurrence of iron in Florida phosphates.8 Note the location of the seven triangles which repre-

Jan 1, 1972

By Walter W. Bradley

Barite, or barytes as it is sometimes called, belongs to one of the lesser groups of nonmetallic minerals, of which 15 to 20 varieties are mined in California in amounts varying in value from a few hundred to almost half a million dollars annually. Commercial production of barite in California, according to the records of the State Mining Bureau (now Division of Mines), began in the year 1910 with shipments totaling 860 tons, valued at $5640 f.0.b. rail shipping point. With the exception of the years 1924 and 1925, when no shipments were made, the output has varied, reaching a maximum of 17,993 tons, worth $90,617, in 1927. The 1928 output was 13,406 tons, worth $55,888 f.0.b. rail shipping point, bringing the state total to the end of 1928 to 59,972 tons, valued at $313,930. Consumption of BaRitE in United States Crude barite sold or used by producers in the United States for the year 1927 amounted to 248,219 tons, valued at $1,594,423, according to the U. S. Bureau of Mines.l In addition, there was imported, principally from Germany, a total of 70,274 tons, valued at $253,284. Manufactured products from these tonnages combined were distributed in 1927 (the latest year for which figures are at present available) as follows: ground barite, 57,658 tons; lithopone, 174,083 tons; barium chemicals (including carbonate, 4,960 tons; chloride, 3,541 tons; binoxide and sulfate or blanc Jixe combined, 13,354 tons). Missouri accounts for nearly 50 per cent of the domestic crude barite, followed by Georgia and Tennessee, with lesser amounts from Arizona, California, Nevada, South Carolina, and Virginia. Occurrence and Uses of Babite2 Barite, also called "heavy spar" and "tiff," is theoretically composed of 65.7 per cent of barium oxide (BaO) and 34.3 per cent of sulfur

Jan 1, 1931

By AIME AIME

WINFIELD SCOTT MORRIS, known from Coast to Coast within the petroleum industry as "Buck" Morris, is and has been for several years an outstanding man in the Petroleum Division of the A.IM.E., so it is most natural to have him as the Chairman of the Division. "Buck" has been such a vociferous promoter of everything TEXAS that most of his friends believe him to be a "Longhorn" by birth-but the records show he was born at Wilmington, N. C., on July 29, 1901. He worked his way through college and graduated from the University of North Carolina in 1924 with a B.S., followed by a C.E. in 1927. His graduation thesis was entitled "De¬sign of a Modern Oil Refinery."

Jan 1, 1944

Olof Venstrom (communication to the Secretary*):—In order to do justice to a property, once the largest producer of copper in the world, which is now being reopened, with a fair promise of again becoming important, I beg to add a few words in connection with Mr. Souder's remarks on the El Cobre copper-mines. The El Cobre copper-mines were worked by the old English

Jan 1, 1905

By Homer S. Frankhouser

Materials may be dredged, processed, stored and loaded for shipment at a single site in water depths ranging from 250 to 1200 ft. Solution mining may also be accomplished in deep sea situations. And, open air subsea mines with direct surface access may be developed and worked under the ocean floor. These concepts for deep sea mining are the results of extensive testing of individual components of the proposed systems by Dravo Ocean Structures, Inc., a subsidiary of Dravo Corp. A basic structure in these systems is the articulated platform. The platform consists of a gravity- type base and a buoyant cylindrical column which is constructed at an onshore location, towed to the offshore site and installed in a matter of days without use of heavy equipment. The base is also buoyant for towing purposes. This allows for gradual flooding to the point of negative buoyancy for positioning and anchoring to the ocean floor.

Jan 1, 1971

By Arthur F. Johnson

Plant sites for the light metal industry must be located where ample low cost power is available. In the first half of the century hydroelectric development was the only source of this power-now the best sites have been exploited and those remaining do not promise enough water to permit year-round capacity power plant operation. In searching for economic plant sites engineers have concentrated on locations with vast water power potential. Olin Mathieson Chemical Corp. has been studying the economics of developing water power to make aluminum. However natural gas, lignite, and even atomic energy have also been considered as possible power sources for aluminum production. Economic studies have given consideration not merely to investment and production costs, but to total costs of delivering fabricated products to the market center of the U. S. When delivered costs are considered and when full account is taken of the newest techniques of mining bituminous coal and utilizing it to make electric power, one arrives at the inescapable conclusion that coal has emerged as the economic answer to American aluminum production.

Jan 4, 1955

Reports on process control computer projects at the Kamioka Plant are summarized from the Japanese technical literature (see references). Fluidized Bed Roaster and Sulfuric Acid plant1 A small process control computer (Yokogawa CCS-200 with an OKITAC 5090P 8K central processor) was installed in the Kamioka smelter in the summer of 1964. A year-and-one-half installation project followed, which successfully brought the roaster and acid converters under computer control. The process plant consisted of two 130 RPD fluosolids roasters and two Monsan to acid units. The roasters are charged with lead-zinc concentrates with SO2 from the roaster processed to sulfuric acid. The computer system provides the following functions: 1) log data from the plant--the input is taken from 50 analog signals, 130 high-low digital alarm points, and 50 analog high- low alarm points; 2) set-point control on 18 control loops; 3) direct digital control (DDC) on eight control loops for which conventional controllers were difficult to adapt due to abnormal loop characteristics or delay times; 4) execution of a safe shut-down procedure

Jan 1, 1969

By R. W. Raymond

The Mining Law of New Pork, contained in Title XI., Chapter IX., Part One of the Revised Statutes, is as follows: Section 1. The following mines are, and shall be, the property of the people of this State in their right of sovereignty : (1.) All mines of gold and silver discovered, or hereafter to be discovered, within this State. (2.) All mines of other metals discovered, or hereafter to be discovered, upon any lands owned by persons not being citizens of any of the United States. (3.) All mines of other metals discovered, or hereafter to be discovered, upon lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain less than two equal third parts in value of copper, tin, iron, and lead, or any of those metals. Sec. 2. All mines and all minerals and fossils discovered, or hereafter to be discovered, upon any lands belonging to the people of this State, are, and shall be, the property of the people, subject to the provisions hereinafter made to encourage the discovery thereof. Sec. 3. All mines of whatever description, other than mines of gold and silver, discovered, or hereafter to be discovered, upon any lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain two equal third parts or more, in value, of copper, tin, iron, and lead, or any of those metals, shall belong to the owner of such land. Sec. 4. Every person who shall make a discovery of any mine of gold or silver within this State, and the executors, administrators, or assigns of such persons, shall be exempted from paying to the people of this State any part of the ore, produce or profit of such mine for the term of twenty-one years, to be computed from the time of giving notice of such discovery, in the manner hereinafter directed. Sec. 5. No person discovering a mine of gold or silver within this State shall work the same until he gives notice thereof, by information in writing to the Secre-

Jan 1, 1888

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies'-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday's law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5'= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

By Milton Fies

ALTHOUGH pig iron from iron ore and red cedar charcoal preceded the mining of coal by many years, for tradition says that Alabama iron was used to shoe the horses of Andrew Jackson's soldiers, coal was not produced until 1830. In that year, coal was mined in Tuscaloosa County, in the vicinity of what is now the University of Alabama, and shipped on flat boats (obviously during the wet season, for there were many shoals) down the Warrior River to Mobile. About that time, the first railroad, the Decatur & Tecumseh, was being constructed in northern Alabama to overcome the obstructions to freight traffic caused by the now well-known Muscle Shoals in the Tennessee River. This railroad was patterned after a railroad at Mauch Chunk, Pa., which was used for hauling anthracite from the Panther Creek valley. The Alabama railroad, which required about four years to complete, was 46 miles long and was used solely for the transportation of cotton. Although it was a failure, it demonstrated the practicability of the undertaking, and the succeeding railroads, which were begun in 1834, 1848, 1852, and 1853, added immeasurably to the development of the coal resources of the state. Between the years 1830 and 1860, practically all the coal mined in the state was dug from the outcrop near the river or from the river beds, and shipped by boat to Mobile. Transporting coal down the Warrior River was one of great risk, required much skill, and frequently had heavy losses. It is recorded that this coal was sold to the gas company in Mobile in 1844; it was most likely mined from the Black Creek Seam. In 1914, on the completion of Lock 17, the Warrior River became a navigable stream from 9 miles above Cordova, Ala., to Mobile and offers a great opportunity for the future development of the coal resources of the state.

Jan 9, 1924

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960