Search Documents

By Alfred F. Brainerd

The subject of the supply and the quality of the iron-ore and coke of this State has suffered exaggeration and misrepresentation in both directions. Unsophisticated persons have made extraordinary reports of quality and richness, which could not be supported by facts; while, on the other hand, experts have selected inferior samples, and upon the average of these, which was not by any means the average known to our practice, have based comparisons favorable to other States. Our furnace-records give much better testimony as to the run of our ores, the calorific duty of our coke, and the burden and blast which it will bear. Some of them show poorer ore-mixtures than others; but it is safe to say that the Birmingham furnaces produce from 40 to 60 per cent.. of iron from a mixture of equal parts of the leanest and the richest ores, as classified in large quantities. And certain performances on record here, while they do not represent the regular or average practice, ma: be fairly urged as proof of excellence of raw material, since they would otherwise have been impossible, even as exceptional achievements. Thus oue of our furnaces has made iron with 2500 pounds of coke to the ton of 2300 pounds (Mr. Stratton, 1888); another, with a ton of coke to the ton of iron (Mr. Gordon, 1888); another, with 1.27 ton of coke to the ton (2300 pounds) of iron, the product in the last case being from

Jan 1, 1889

By T. A. Rickard

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes on, like some writers, talking about `the former' and `the latter', `he', `she', `it', and `they', through !clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a' feeble ending for a serious statement. How often do you hear `the former' and `the latter' in conversation? Good conversation is a guide not to be dis¬dained. When you must use `the latter', do not confuse it with `the last'. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is best. I "Partly prevented" is a poor phrase. `Prevented! is a word that does not lend itself readily to modification. He means `checked' or `corrected'.

Jan 1, 1931

By Eli T. Conner

WITH Thomas G. Fear, chairman of the Coal Di- vision, presiding, the coal miners opened their program Monday morning with a general session at which three papers were presented. The first, "The Classification of Coal for Stationary Steam Generation," was presented by the author, Thomas W. Harris, Jr. In discussion, H. T. Coates inquired if it would not be possible to pick out a geographical coal section, certain seams or a group of mines, which would rank high in a desired feature or features, perhaps giving different -- - local sections or different mines something to designate a rating ("good," "fair," and "poor"). This might be done relative to anti-clinkering, free-burning, ,anti-slagging, smokelessness, friability and grindability. These might be listed or arranged on a map or diagram so that the prospective customer could find a coal that rated particularly high in desired characteristics. C. A. Reed pointed out, in part, that coal producers and sellers have found a bad but necessarily present condition in the country, especially with the smaller user of coal. This is entirely due to the fact that the employer expects his purchasing representative to be a genius and have expert knowledge of everything he buys, coal included, whereas in the larger plants he has and uses expert knowledge from the active organization when necessary. J. B. Morrow said that size rating was important in classifying coal and he emphasized that it was impossible to come to a definite basis on analysis alone.

Jan 1, 1933

By John B. Myers

VERMICULITE is a name used to describe micaceous material that exfoliates when heated. It is hydrated magnesium-aluminum-iron silicate. The chemical composition, color, physical appearance, and degree of exfoliation vary. COMPOSITION, PROPERTIES, AND ORIGIN Vermiculite has the characteristic micaceous structure of basal cleavage and readily splits into thin laminae, which are soft, pliable, and inelastic. The monoclinic crystal faces are often marked by triangular lines at 60° and 120°. Hardness is 1.5; specific gravity, 2.2-2.7; luster pearly to greasy; colors, amber, bronze, reddish brown, dark green, and black. Feel is soapy, particularly when wet. When heated it exfoliates by expanding at right angles to the cleavage into long wormlike pieces (the name vermiculite is from the Latin veamiculari, to breed worms). This important characteristic of expansion is believed to be a mechanical separation of the layers when the contained water is converted into steam. Warping of the unit layers may also contribute to the expansion. The increase in bulk volume of commercially prepared material is 8 to 12 times but individual flakes may increase in size more than this. Pure vermiculite is a distinct mineral and has the structural formula (OH), (Mg,Fe)3 (Si,Al,Fe)4 010.4H20. It rarely occurs in this pure form, but generally as a mixed mineral of varying structure. One explanation is that the mixed material is composed of unit layers of inter-stratified pure vermiculite and biotite. The essential difference between the two is that unit cell structure of vermiculite contains a layer of water molecules whereas the biotite cell contains potassium instead of the water. The water content of the mixed vermiculite is less than that of pure vermiculite but more than that of biotite. Pure biotite does not expand when heated. If the proportion of biotite layers in a vermiculite is too high it will adversely affect the degree of exfoliation. Within a given deposit, the great mass of material may approach a definite com-position with local areas of greater biotite content. It is not uncommon to find also small pockets of pure biotite but these are generally segre-

Jan 1, 1949

By C. B. Manula, R. Venkataramani

Application of computers to present-day open-pit mining with bucket wheel excavators (BWE) is discussed. The development of the wheel excavators and their use in mining are discussed along with the necessity for building a computer model of the bucket wheel and the mathematical formulation of the problem. The simulation procedure, testing the model, and test results are summarized. Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the 20th century. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management, and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mold of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. Constant efforts are needed to improve upon productivity if the ore is to be economically mined. The development of vast low-grade deposits and thick overburden deposits calls for better tools to handle the enormous amount of materials. A natural solution to this problem is the use of bucket wheel excavators (BWE), which employ a continuous cutting head to feed the materials handling system. High productivity, versatility, economy of operation, and adaptability to most types of haulage systems combine to make BWE's attractive for large earth-moving operations. "Operating costs are being pushed down by the impact of giant haulage units, by high-speed conveyors, and computerized railroads. Matching all these with the continuous output of BWEs, one can visualize increased production at much lower costs." Historical Background The wheel excavator, which was patented in Germany in 1913, made its first appearance in an open-pit lignite mine in 1920. From this early beginning, however, BWEs were slow coming into practice. Initial developments were dampened by many design problems. From 1936 onward, major developments in design improved the wheel's ability, capacity, and versatility. A literature survey shows that wheel excavators are being used in Australia, Zambia, South Africa, the Congo, India, Indonesia, Czechoslovakia, Russia, Great Britain, Guyana, Yugoslavia, Morocco, Germany, Canada, and the U.S. for mining and loading chalk, lignite, clay, sandstone, phosphate, broken ore of iron, coal, shale, loose and semi-loose rock overburden.' A recent LMG* BWE at work in a German lignite mine weighs 6790 tons with an hourly capacity of 11,000 cu m. Although the BWE has wide applicability, its application to new mining areas poses a problem. Because of the large capital investment involved in BWE application and the narrow profit margins in mining low-grade ores or coal at depth, little margin of error can be tolerated in the selection, design, and operation of these machines. The questions that need to be answered prior to installation of a BWE for a mineable deposit are: 1.) What are the anticipated BWE performance characteristics? 2) Which method of BWE operation is most efficient? Attempts to answer these questions require a thorough knowledge of the mining system and the BWE operation. One approach is the building of a computer-ori-ented simulation model to determine how information and policy create the character of the BWE system under consideration. BWE Operation Modern BWEs generally excavate in blocks. Fig. la shows a BWE working in an established cut. The wheel is positioned to travel on the pit floor in line with the top edge of the old highwall. As it advances, a new highwall is exposed in the direction of excavation. Digging is done by rotating the wheel, swinging it from side to side in long parallel arcs, and "crowding" into the bank, by advancing the entire machine, or by the travel of the digging boom if an automatic crowd is available (Fig. lb). A second way by which the wheel can be advanced into the bank is by the falling cut method. A brief description of each of these methods follows. Cut with a Crowding Machine: At the end of every swing, the digging boom can be extended by the thickness of cut desired and the boom swung back in the reverse direction. Obviously, the thickness of bank excavated does not vary with the boom position; therefore, the slewing motion of the boom is fairly constant for uniform output. The thickness through which the digging boom can be advanced into the bank is theoretically calculated from the formula'

Jan 1, 1971

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By Hugh S. Spence

IN MAY, 1930, G. LaBine and E. C. St. Paul, prospect¬ing round the southeastern shore of Great Bear Lake, in the North West Territories of Canada, discovered pitchblende at what is now LaBine Point. At the same time, they also found native silver in a small sheared break on an island lying off the point. Late in 1930, samples of the pitchblende were sent to the Mines Branch, at Ottawa. The material consisted of several fair-sized slabs of botryoidal pitchblende banded with a brownish quartz. A small amount of chalcopyrite was visible as small particles and fine veinlets, and the pieces were rather heavily stained a yellowish-green by secondary copper-uranium salts. Analyses were run in the Mines Branch Ore Dressing Laboratories on two samples, and small-scale concentration tests were made on one of them. The results of this work were published in a Memorandum Series report (No. 48) of the Mines Branch, in March, 1931.

Jan 1, 1932

By Frank Soulé

Secretary E. H. Benjamin, of the California Miners' Association, has proposed and begun, in co-operation with the testing laboratory of the University of California, at Berkeley, a series of tests which should prove of great interest and practical use to all persons making extensive application of steel wire cables, and especially to miners who run them in deep mines. Mr. Benjamin is endeavoring to obtain pieces of cable both new, and old and worn, from every deep mine of importance on the Pacific Coast, together with all the data obtainable concerning their manufacture and particular use. Pieces from each sample will be broken ill the laboratory before mentioned: and as far as possible the effects of winding around drums or pulleys ; of sudden starting and stopping when loaded; of heavy shocks, and of the general wear and tear of the cables, will be ascertained by these tests. The Olsen testing-machine of 200,000 pounds capacity will be used to break the cables, and the rupturing force, in different instances, will be applied slowly and also rapidly, in order to make the tests comparable as far as possible with the practical use of the cables themselves. All information and data available should be obtained for each specimen sent to the laboratory, the name of the manufacturer, the date of making, strength of cable when new and unrusted, as well as the circumstances and conditions of the practical use of the cable. Having this information before us, we shall be able to tell, approximately at least, the effects of age, rust, wear and tear, shocks, etc.; and perhaps be enabled to draw the line of limitation beyond which it would be no longer safe to use a cable of known manufacture. Moreover, by means of such tests we may, perhaps, he able to recommend worn cables for other uses, less severe in character, thereby prolonging the life of their effective usefulness. When we consider the great number of miles of steel cable now in use, and of the greater number constantly being manu-

Jan 1, 1900

By J. Kostuik, M. J. de Bastiani

The method of mining the uranium orebody at Denison mine in the Elliot Lake district of Ontario is discussed. Details of the development of haulage-ways and rooms are giuen, as well as methods of ore haulage. The milling and beneficiation stages are noted briefly. Located in the Elliot Lake mining district of Canada, the Denison mine lies between Sudbury to the east and Sault Ste. Marie to the west, Fig. 1. This area is overlain by Huronian sediments filling a basin in the Keewatin basement complex. Subsequent folding of these sediments developed a synclinal structure, known locally as the Quirke Lake Trough, which forms the northern portion of the now famous big Z structure, the geological trademark of this region. Plunging to the west and extending nine miles from the granite outcropping in the north to the Keewatin lava contact to the south, the syncline has dips of 10" to 45" on the north limb and 10" to 20" on the south limb, Fig. 2. The Denison orebody, located on the north limb of the syncline, lies between 800 and 3000 ft below the surface. The main ore zone is within 50 ft of the Missisagi-Keewatin contact (see Fig. 3), and it varies in thickness from 6 to 32 ft. This ore zone has a composite dip of 19" to the south and is composed primarily of two pyritized conglomerate beds separated by a band of pebbly quartzite stratum. The upper conglomerate bed of the main zone varies from 2 to 15 ft in thickness, while the lower conglomerate varies from 2 to 12 ft. Over extended areas, mining is carried out over the entire section comprising the two conglomerate layers and intercalated quartzite; in other areas, the conglomerates are selectively mined, depending on the thickness of the quartz-ite. The ore zone contains approximately 6 pct sulfides and 80 pct silica. The predominant uranium-bear ing minerals are brannerite, uraninite, and an unidentified mineral (probably thucolite). Some of the uneconomic metallic minerals identified to date are pyrite, pyrrhotite, and chalcopyrite. MINE LAYOUT Shafts: Underground exploration and development (Fig. 4) were performed through two shafts 1/2 mile apart. The No. 1 shaft, sunk to a depth of 1856 ft with the main station established at the 1600-ft ore level, is a 250-sq ft, 5-compartment shaft capable of handling 4500 tpd. Two 5x5-1/2-ft compartments serviced by a 12-ft diam double-drum hoist, are used for hoisting 190-cu-ft bottom-dump skips in balance. A 30-man cage, offset by a counterbalance, operates within a 5-1/2x11-1/2-ft compartment. The fifth compartment is used as a manway, pipe, and cable-way. This shaft is also provided with an intermediate pumping station used during the initial mining phase as well as loading-pocket and spill-pocket installations and pumping facilities. The 480-sq ft No. 2 shaft, located down-dip from No. 1 shaft, has a 2776-ft depth. Serving as the main hoisting shaft with a maximum capacity of 9000 tpd, it has eight compartments, four of which are used for hoisting ore in 10-ton capacity bottom-dump skips. These four compartments, measuring 5x6-ft in section, are serviced by two 12-ft diam double-drum semi-automatic hoists. A 50-man cage is operated in a 15x8-ft compartment, and it is counterbalanced by a 12-ton weight. Two compartments are used for ventilation, manway, electric cables, and pipes. A station was constructed at the 1325-ft horizon of the No. 2 shaft for relay pumping. The main sta-

Jan 1, 1961

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972

By A. D. Hodges

The great mining region of Peru is a mountainous belt of country, running nearly the whole length of the republic, and comprising the two grand ranges of the Andes with the elevated table-lands between them. On the east of this belt are the extensive plains and fertile valleys of the Amazon and its tributaries. On the west is a narrow strip of coast 20 to 50 miles wide, for the most part a sandy desert, but producing abundant crops where irrigated ; and here are found petroleum (Department of Piura), salt (at Huacho and elsewhere), nitrate of soda in enormous amounts at the south, silver in a few localities (Province of Tarapaca), copper and other mineral products. The Western Cordillera, running nearly parallel with the shoreline, rises like a wall on the eastern side of the coast-belt, with passes from 15,000 to 18,000 feet high and peaks attaining 18,000 to 20,000 feet. Further east, at a varying distance, is the Eastern Cordillera, composed of broken mountain ranges which, considered as one group, have a general parallelism with the western chain, but individually vary greatly in direction, sometimes running nearly east and west, in places projecting out into the Amazonian lands, or here and there curving around to unite with the western ridge, and with this enclosing immense inter-alpine plains. These general features are indicated in Fig. 1. The surface of these plains is uneven and traversed by lower ranges of hills which surround large lakes, or rolling pampas, or fertile valleys; and through many of these last run rivers of considerable size. The whole country has a high altitude (averaging up to 15,000 or 16,000 feet), and slopes gradually north and east towards the Amazon, into which drain all its waters. Its bounding mountain chains are scored on all sides by narrow, picturesque and pre-

Jan 1, 1888

By O. R. Wagner, R. O. Leach

Immiscible displacement tests were performed in a consolidated sandstone core over the interfacial tension range from less thdn 0.01 to 5 dynes/cm to better define how interfacial tension (IFTJ reduction can lead to increased oil recovery. Data obtained were displacement efficiency at breakthbrough vs IFT for both drainage and imbibition conditions. These tests simulate water flooding under oil-wet and water-wet conditions, respectively. Results of the study have shown that displacement efficiency under both oil-wet and water-wet conditions can be markedly improved by a sufficient reduction in IFT. In the particular porous media used and for the low pressure gradients employed, the IFT must be reduced to a value less than about 0.07 dynes/cm to achieve increased recovery at the time of breakthrough of the injected phase. Below 0.07 dynes /cm, further small reductions in IFT result in large increases in displacement efficiency. Observed increases in recovery were obtained at pressure gradients which are well below those which can exist in the interwell area of a reservoir under water flood. The effect of pressure gradient on recovery is discussed. INTRODUCTION A residual oil saturation remains in rock which has been water flooded because, under usual reservoir conditions, the driving force which can be generated is inadequate to expel oil trapped by capillary forces. Since these capillary forces can be reduced by reducing the IFT a frequently studied method of increasing oil recovery has been the use of surfactants to reduce the water-oil interfacial tension. Mungan l observed improved recovery in both water-wet and oil-wet systems at 1.1 dyne /cm IFT, finding that the amount of improvement was greater in oil-wet systems. Moore and Blum,2 working with visual flow cell micro-models, con- cluded that recovery cannot be improved in water-wet systems by injecting surfactant solutions. They calculated that, for a pressure gadient of 1 psi/ft in their model, the IFT must be reduced to 0.03 dynes/cm to release oil trapped under water-wet conditions. Berkeley et al.3 indicated that, at representative field flooding rates, the IFT must be reduced to 0.001 dyne/cm to improve recovery, Thus, there is a wide variation of opinion about the IFT levels needed to improve recovery under field conditions. These previous investigators all have used as their experimental method the addition of surfactants to the injected water. The use of surfactant solutions to reduce IFT creates two experimental problems: (1) the loss of surfactant through adsorption on reservoir rock can obscure the true IFT value which exists at the displacement front, and (2) at very low values of IFT emulsifica-tion of oil and water commonly occurs. It is difficult, therefore, to determine whether the increased recovery is caused by IFT reduction as such, or is instead caused by emulsification. Also the properties of the available surfactants limit the IFT range which can be studied. In the present study the purpose is to better define how interfacial tension reduction can lead to increased oil recovery. A matter of great interest is the amount of recovery improvement potentially achievable in this way. The study was made using very low pressure gradients which was well within the range achievable by water flooding in the interwell region of petroleum reservoirs. A unique experimental approach was chosen to avoid adsorption and emulsification problems, and to allow convenient control of IFT. The fluid phases used were the equilibrium vapor and liquid phases of the methane-n-pentane system. The interfacial tension level was varied by changing the equilibrium pressure of the methane-pentane system over the range from 1,200 psia to near the critical pressure (2,420 psia). All tests were performed at a controlled temperature of 100F. The IFT-vs-pressure relationship for the methane-pentane system was based on the data of Stegemeier and Hough,6 and on new data obtained in this study. With this experimental approach it has been possible to study displacement at lower values of IFT than have been previously investigated.

Jan 1, 1967

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By C. G. Dunn

The measurement of interfacial teusions or grain boundary energies in metals is an important metallurgical problem, especially since it bears on growth and nucleation processes. Statistical methods of measuring equilibrium grain boundary angles, which relate interfacial tensions, have been used by some investigators1'2 but more direct methods would be preferred. A direct way, based on a simple extension of a successful method of growing single crystals of silicon ferrite to predetermined orientations in flat specimens,3 is to produce three-grain specimens in such a way that the equilibrium common grain boundary will be perpendicular to the surface of the specimen. The angles to be measured then appear as the grain boundary angles in the surface of the specimen. The method of producing a single crystal specimen with a predetermined orientation is basically the same as that employed by Yoshida and Fuji-wara4 in their work on aluminum wires. The specimen, prior to any single crystal transformation, must have a matrix which will support the growth of a crystal of the desired orientation. Growth may occur through exaggerated grain growth or, if the matrix is strained a critical amount. by normal recrystallization. In either case the matrix must have stability at the temperature used to effect the transformation, this stability appearing as a long induction period for exaggerated grain growth or for the formation of recrystallization nuclei. Additional control is gained by using a high temperature gradient through which the specimen is moved at a suitable rate. To obtain the desired orientation, the specimen is fed a short way into the furnace producing one or more crystals in the hot end. After the specimen is removed from the furnace, the orientation of a crystal is determined, so that this crystal may be reoriented by properly deforming a narrow piece of the matrix between the end crystal and the rest of the specimen. This part of the specimen in the case of silicon ferrite is preferably held at red heat during the reorienting process. Fig 1 shows a specimen which is ready to be transformed into a single crystal through growth of a reoriented "seed" crystal. When the method just described is applied to the production of a three-grain specimen two crystals are grown first side by side in one end, the specimen is then reversed and the third grain grown from the opposite end. A suitable group of grains each of different orientation is one where all three grains have the same crystallo-graphic plane in the plane of the specimen. Fig 2 shows a photograph of a three-grain group prepared as described. The notches are introduced in the open ends of the grain boundaries to anchor them during the final annealing operations which ultimately should bring the grain boundaries to the lowest energy configuration. Two-grain groups with different crystallographic planes in the plane of the specimen can be similarly prepared and treated. If the two grains have different surface (gas to metal) energies per unit area, the equilibrium condition leads to a curved grain boundary.* * This feature of the problem was pointed out by J. c. Fisher. References 1. Cyril Stanley Smith: Grains. Phases and Interfaces: An Interpretation of Microstructure. Trans. AIME 175, 15. Met. Tech. TP 2387, June 1948. 2. D. Harker and E. Parker: Grain Shape and Grain Growth. Trans. A.S.M. (194,5) 34, 156-195. 3. C. G. Dunn, A. Seddon, and R. Wylie: Unpublished Work, 1946-1947. 4. Takeo Fujiwara: A Method of Producing A Long Single-Crystal Wire of Aluminum with any Desired Crystallographic Axis. Jnl. of Sci. Horoshima Univ. A, (1939) 9, No. 3, 227.

Jan 1, 1950

By D. J. Jr. McAdam

This paper presents stress-cycle graphs for five samples of monel metal and three high-strength aluminum alloys. These graphs are evidently curves with horizontal asymptote. The position of the horizontal asymptote can be determined with sufficient accuracy by extending the experiments to not more than 50,000,000 cycles. For some of the graphs, there is a slight downward slope between 50,000,000 and 100,000,000 cycles. The slope is so slight, however, that, extrapolation from 50,000,000 to 100,000,000 cycles gives the endurance limit with sufficient accuracy. Monel metal and duralumin are not exceptional among non-ferrous metals in endurance properties. IN Part I of this paper' a comparison was given of the results obtained in investigation of the endurance properties of non-ferrous metals in .three laboratories: the Engineering Experiment Station of the University of Illinois, the U. S. Air Service at McCook Field, Dayton, Ohio, and the U. S. Naval Engineering Experiment Station, Annapolis, Md. Part I was devoted to a discussion of the forms of the stress-cycle graphs obtained at the three laboratories. For comparison, typical graphs obtained at the three laboratories were plotted on the same semi-logarithmic scale. The typical rotating-cantilever graph for ferrous and non-ferrous metals obtained at the Naval Experiment Station was described as a curve descending with gradually decreasing slope to a horizontal line. In the reply to the discussion of Part I, however, this graph was described as a curve with horizontal asymptote. It. was also said that the ordinate of the asymptote (the endurance limit) could be determined by endurance tests of not more than 50,000,000 cycles. This description was intended to apply only within the range of ordinates used in plotting an ordinary endurance graph. It was recognized that if .extended upward beyond the usual field, the curvature of the graph would decrease until -the graph would either approach a straight a line or possibly reverse its curvature.

Jan 2, 1926

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By Jack L. Taylor

Single crystals of tungsten grown from powder -metallurgy swaged rod by high-temperative annealing were deformed in tetzsion at temperatures from 2500 to 5000 OF. Orientation of specittzen tensile axis, strained ratrix, and defortnation bands was determined optically by reflections from {110} etch pits. Slip traces meve analyzed and slip directiorz determined. Results indicate that {110}(111) , {112){111}. and {123}{111} type slip occur in tungsten over the terpe,atuve rutge investigated. Slip is orientation-dependent occuvring on tCuzt cowzbitzation oj slip plane and direction which has the highest critical resolved shear stvess. Overshooting appears to be a general occurrence between 2500' and 5000°F. Dejornatiotz bands show rotation in a directiorz opposite to the yotation of tire tensile axis. DEFORMATION in bcc metals has been reviewed by Maddin and Chen,' Keh and eissman,' and most recently by Nabarro, Basinski, and olt. From these reviews it is apparent that some disagreement exists concerning the crystallography of plastic deformation in bcc metals. There is evidence of noncrystallo-graphic slip, the crystal slipping on or near a noncrys-tallographic plane in the (111) zone for which the resolved shear stress is greatest. There is also evidence to indicate that crystallographic slip occurs in the planes of the same zone. On the other hand, there is agreement that the close-packed direction ( 111) is the slip direction in bcc metals. Further, in pure bcc metals4 and alloys the operative crystallographic slip systems are strongly dependent on temperature. Both crystallographic and noncrystallographic slip have been reportede8 in tungsten, a group VIA bcc metal. The number of slip families which operate in the case of crystallographic slip, however, has been in question. The earliest study by oucher' of single-crystal tungsten tested at temperatures of 1800 to 5000°F led to the conclusion that only {112)( 111) type slip operated. Raymond and eumann recently reached the same conclusion studying deformation by rolling of plasma-flame single crystals at 1800°F; however, only [loo] and [110] orientations were studied. Work at high temperatures by Leber and Pughs on tungsten and Chen and Maddin9 on molybdenum suggests that conjugate slip on nonparallel (110) planes may account for the slip on (112) and (123) planes found by others working with bcc metals. The present paper presents evidence of three families or modes of slip in tungsten in the temperature EXPERIMENTAL PROCEDURE Material. Standard microtensile specimens, 0.160 in. diam by 0.640 in. gage length, were ground from commercial powder-metallurgy swaged tungsten rod, type MK. Specimens were heated for 10 min at 5150°F or 6 hr at 5400°F in vacuum of 1 x 105 Torr or less to produce single crystals. At the lower temperature an average of two out of seven specimens heated in a group developed single crystals throughout the specimen length as shown in Fig. 1, the rest remaining wholly poly crystalline. At the higher temperature, three or four out of seven specimens became single crystal. Other than to note that Laue X-ray photographs generally showed sharp, well-defined spots, no attempt was made to assess crystal perfection or measure dislocation density. Two tungsten single crystals grown from the melt by the plasma-arc process were also used for this study.

Jan 1, 1967

By Fred D. DeVaney

W. O. Philbrook (Carnegie Institute of Technology, Phila.)—Mr. DeVaney's paper is a valuable addition to the growing technology of the magnetic roasting of lean iron ores. His furnace is ingeniously designed to permit close control of the process and to achieve high thermal efficiency by counter-current heat exchange and the withdrawal of both solid and gaseous products at relatively low temperatures. The principle of using a lean reducing gas to avoid over-reduction of the ore even at high operating temperatures (for rapid re-action rate) is thoroughly sound. The gas analyses and flow rates reported, however, are internally incon- sistent and render suspect any details of a heat balance based upon them. While it is entirely proper to consider the entrant gas as a reagent and to account only for the heat evolved by consuming a portion of the gas, many operators are accustomed to a heat balance using the total calorific value of the reagent supplied; and comparison of heat balances made with different bases of calculation can be quite misleading. Since Mr. DeVaney's paper is likely to be cited frequently in future discussions of magnetic roasting processes, it seems worth while to point out the internal discrepancies and to give alternate values of heat requirements for different bases of calculation.

Jan 1, 1954