Search Documents

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase 'fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,' hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.' It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

By Richard W. Lodge

In the crucible-method of assaying ores for silver a certain amount of litharge is essential to supply sufficient lead to collect the precious metals. The object of this paper is to point out that the use of a large excess of' litharge in the assay of some ores will give results for silver that are uneven as well as low. So far as I know, however, an excess of litharge does not affect the results obtained in the crucible-assay of ores for gold. The main reasons for using, in the crucible-assay, much more litharge than is required to givc the necessary lead button are: 1, its action as a flux; 2, its action as a desulphur-izer; and 3, its action as an oxidizer, especially on metals like copper and nickel, whereby they are forced into the slag as oxides and thus prevented from passing into the lead button. Hence, by the use of much litharge in the crucible-assay more ore call often be taken than in the scorification-process, and a lead button obtained which call possibly be cupelled at once or after a single scorification. The method is specially advantageous with an ore carrying much copper or similar impurity and poor in silver, when the assayer does not wish to resort to a wet-analysis for the determination of the silver. It is well known that some ores give better results when assayed by the scorification-method, while others give better results by the crucible-method. For several years I have noticed that, when much litharge was used with certain sulphide and arsenical ores, the results were considerably lower than when the scarification-method was used. This fact was more forcibly brought out in connection with certain work carried on this year by Messrs. H. A. Frame and

Jan 1, 1908

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

By Frederick Prime

The first catalogue of Geological Reports of the United States was prepared by Prof. 0. C. Marsh, and published in the American Journal of Science and Ark for 1567, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought clown to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen : The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. R. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va.; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College; Mr. Sanderson Smith and Prof'. J. J. Stevenson, of New York; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers.

Jan 1, 1879

By James S. Browning

The Mineral Resources Institute and State Mine Experiment Station of the University of Alabama conducted Humphreys spiral tests on fine coal waste from nine preparation plants of Alabama strip mining operations to determine the feasibility of recovering low ash and sulfur fuel meeting steam coal specifications. The ash in the samples ranged from 9 - 5l%, and the total sulfur ranged from 0.4J- 2.39%. Continuous laboratory tests using a Humphreys spiral gave good recovery of the coal with excellent rejection of the ash and pyritic sulfur. Coal recoveries of 83.6 - 94.1% were achieved from the different samples. Ash content of the clean coal products fell within a range of 5 - 12.2%, with a total sulfur content of 0.62 and 1.10%. In quality, the products were comparable or superior to those now being shipped from the preparation plants.

Jan 1, 1980

By St. John, JOHN Ancel

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to bean alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated.

Jan 1, 1927

By J. A. Snyder, W. L. Finlay

G. Edmunds—Solid solubility is considered to be of either the interstitial or the substitutional type. Is it possible, in a binary alloy as the simplest case, that some of the solute atoms are present in the normal lattice sites (substitutionally or filling lattice vacancies) while simultaneously others are in interstitial positionss One might even ask whether a distribution of the two types may be the normal situation. H. M. Meyer—Metastable states of interstitial atoms occupying vacant lattice sites possibly occur as well as of substitutional atoms squeezed in between regular matrix positions. However (as we know since Hume-Rothery), the solute atoms choose between the two kinds of solutions; consequently, every solute will be unequivocally either substitutional or interstitial in the equilibrium state of the solid solution. M. Balicki—In view of the fact that the authors apparently correlate the analysis of the alloys at the ingot stage with the properties exhibited at the testing stage, I would like to ask whether this is a fully justifiable procedure. In other words, how good are their determinations of solute concentration for correlating them with the mechanical properties. The answer to this question may explain some of the divergencies. Assuming good enough homogenization of the samples and exact determination of mechanical properties the position of the plotted experimental points will depend solely upon the accuracy of composition determination. If this is not accurate, say due to loss or pickup of elements during processing from the ingot to the testing stage, or due to a systematic error in the method employed for obtaining solute concentration data, the points will deviate from their true position and may align themselves along a different curve than the one expected. H. V. Kinsey—We have been studying the creep-rupture properties of titanium-base alloys at 1000°F. In the course of this work, anomalies in behavior of the alloys that would suggest that the material under test was becoming stronger as the test progressed have been observed. If this was so, the most likely explanation that we could think of was that the test bars were absorbing oxygen and nitrogen from the air during the test and were thereby becoming strengthened. In an attempt to determine the strengthening effect of absorbed oxygen and nitrogen the following experiment was conducted. A length of cold-rolled titanium was supplied by the E. I. du Pont Co. Two test bars, having a 1/4 in. diam gauge length, were prepared from this material. One bar was tested in the as-received condition. The second bar was heated in air at 1550°F for 100 hr and subsequently air cooled prior to testing. A testing temperature of 1000°F was employed. The results of these tests are tabulated in table 11. In the author's opinion, is it reasonable to assume that the bar that was exposed to air at 1550°F for 100 hr was stronger because it absorbed oxygen and nitrogen from the air during this heat treatment? W. L. Finlay (authors' reply)—Direct experimental evidence for or against Mr. Edmunds' interesting suggestion will probably never be available. It seems possible, however, that mixed interstitial-substitutional solid solution might well occur with interstitial elements. The less likely possibility of interstitial solution of a normally substitutional element like copper in aluminum was recently discussed at length by the

Jan 1, 1951

By Kalervo Rankama

UNTIL a few years ago, geological mapping, the study of ore boulders, and different geophysical methods were the principal means used in the systematic search for mineral deposits covered by a layer of disintegration products or soil. These methods have been developed to a high stage of perfection as far as the geometrical definition of the conductor is considered. Use of geophysical methods in prospecting is based on the fact that an ore body differs from the country rock not only geologically but also in its physical properties. The general drawbacks and complications included in the use of geophysical methods are well known to everyone who has been using them, so need not be entered into here in detail. One of the more important ones is the fact that geophysical methods are unable to furnish information concerning the chemical composition of the ore bodies responsible for the indications. Further, the ores of many metals, such as silver, gold, beryllium, zinc, mercury, tin, lead, vanadium, antimony, chromium. molybdenum, tungsten, manganese, cobalt, nickel, and the platinum metals cannot be directly located by known geophysical methods, owing to lack of physical characteristics suitable for distinguishing them from the country rock. Thus it is quite natural that efforts have been made to develop direct methods for prospecting and locating ore bodies of the elements named. Known as chemical, biogeo-chemical, and geobotanical methods of prospecting, these have been much improved during recent years. A brief review of these methods and of some results obtained with them will be presented in the following, on the basis of available information and my own experience.

Jan 1, 1947

By J. S. Ll. Leach, L. R. Rubin, M. B. Bever

The energies of formation of ordered and disordered solid solutions of composition CusAu and the energy of ordering in this alloy were determined by tin solution calorimetry. The degree of order was measured by X-ray diffraction and electrical resistance and microhardness measurements were made on ordered and disordered specimens. AMONG the phenomena associated with the order-disorder transformation of a solid solution, the change in internal energy is of special interest because of the part it plays in the various theories of ordering. Published values for the decrease in internal energy accompanying the formation of a superlattice from a disordered solid solution of composition CuAu range from —370 to —2260 cal per gram-atom. Some of these values represent calculations based on theory and others are the results of experimental measurements. The distinction between the change in internal energy, AE, and the change in enthalpy, AH, can here be neglected, because they are approximately equal for solid-state reactions at normal pressure. An analysis of ordering by Bragg and Williams' predicts an energy change of —605 cal per gram-atom for the formation of a superlattice in the alloy Cuau from a completely random solution. Peierls" application to Cuau of Bethe'sb earest-neighbor theory yields —560 cal per gram-atom for the formation of a superlattice from a matrix which initially contains short-range order. Cowley' extended the nearest-neighbor approach to include as many as five shells of neighbors; on this basis a change in energy of —500 cal per gram-atom is expected. Eguchi," using a quantum-mechanical treatment, calculated a value of —2260 cal per gram-atom for the difference in the energy of completely disordered and completely ordered Cu,Au. Sykes and Jones- eated a completely ordered alloy and measured its heat capacity as a function of temperature. This measured heat capacity agrees closely with the corresponding value found by the Kopp-Neumann (or mixture) rule up to about 250°C and above this temperature exceeds it, especially near the critical temperature for ordering. The difference between the integrals with respect to temperature of the observed and the Kopp-Neumann heat capacities was considered to be the energy of ordering. By this method Sykes and Jones found a value of —530 cal per gram-atom. This value is not adjusted for the short-range order remaining above the critical temperature. The pres- ence of such short-range order is suggested by the difference between the measured heat capacity and the extrapolated Kopp-Neumann heat capacity immediately above the critical temperature. Values reported by Weibke and von Quadt' and by Hirabayashi, Nagasaki, and Maniwaa were obtained in the course of investigations primarily aimed at other objectives. Weibke and von Quadt measured the temperature coefficient of the electromotive force of a Cu-CuAu cell. They obtained a value of —1010 cal per gram-atom for the heat of formation of the alloy at 500°C, at which temperature there is no long-range order. They also obtained —1380 cal per gram-atom as the heat of formation of the ordered alloy at 370°C. Considering the heat of formation of the disordered alloy to be independent of temperature, they estimated the energy of ordering at 370°C as —370 cal per gram-atom. At this temperature long-range order is incomplete and the degree of order changes rapidly with temperature. Hirabayashi, Nagasaki, and Maniwa," using an annealing calorimeter, investigated an alloy containing 23.4 rather than 25.0 atomic pct Au and thus could not obtain complete order. Thelr value of the energy of ordering was —490 cal per gram-atom. Orianis has recently investigated the Au-Cu system by the galvanic emf technique. He reports values for the heats of formation of Cu-Au alloys, from which the heat of formation at 427 OC of an alloy of composition CuAu may be found by interpolation. This value is —1080 cal per gram-atom. In the work here reported, disordered and ordered alloys of composition CuAu and corresponding mixtures of gold and copper were dissolved in liquid tin and the heat effects measured. These heat effects are small, since the dissolution of gold in tin is exothermic and the dissolution of copper is endothermic. The method, therefore, yields fairly precise values of the heats of formation of disordered and ordered alloys and of the energy of ordering. Experimental Procedure The calorimeter consisted of a long-necked Dewar flask immersed in a constant temperature salt bath and has been described by Ticknor and Bever." The chief changes in this equipment were an improvement in vacuum and the replacement of the mercury thermoregulator by a resistance thermometer control circuit. The solvent, which was maintained at a constant temperature near 350°C, consisted of 500 grams of 99.99 pct pure tin. The solute samples were mixtures of gold and copper in the proportion corresponding to the composition Cu,Au or solid solutions

Jan 1, 1956

By AIME AIME

Award of a Gold Medal : to the Institute. The Jury of Awards of the Jamestown Ter-Centennial Exposition has conferred a gold medal, the highest distinction within its power,. on the American Institute of Mining Engineers for the excellence of its publications during the past decade. ; A half-tone photographic reproduction of both sides of the medal is given in the accompanying illustration.

Jan 7, 1908

By Eugene McAuliffe

It is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the '(do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co, has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as i'extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment, can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. Safety work in some form has been carried on in and about the mining properties of The Union Pacific Coal Co. since the first mine was opened at the now long-abandoned town of Carbon, Wyo., in 1868. On June 30, 1903, an explosion and subsequent mine fire occurred in mine No. 1 at Hanna, taking 169 lives, and a second explosion occurred in the same mine on March 28, 1908, in which 59 additional lives were lost. Looking back with impartiality on the causes leading up to these two unfortunate disasters, we can only conclude that shooting from the solid, the absence of adequate ventilation, rock dusting, the use of water at the face to allay

Jan 1, 1938

By Eugene McAuliffe

It is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the '(do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co, has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as i'extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment, can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. Safety work in some form has been carried on in and about the mining properties of The Union Pacific Coal Co. since the first mine was opened at the now long-abandoned town of Carbon, Wyo., in 1868. On June 30, 1903, an explosion and subsequent mine fire occurred in mine No. 1 at Hanna, taking 169 lives, and a second explosion occurred in the same mine on March 28, 1908, in which 59 additional lives were lost. Looking back with impartiality on the causes leading up to these two unfortunate disasters, we can only conclude that shooting from the solid, the absence of adequate ventilation, rock dusting, the use of water at the face to allay

Jan 1, 1938

By E. G. Leonardon

THE first to appreciate and foresee the value of applying electrical measurements to structural studies was Prof. Conrad Schlumberger, Professor of Physics at the School of Mines in Paris. One of his earliest practical undertakings in this line was carried out, in the field, at Fierville-la-Campagne, Normandy, in 1912. His book, published in 1920,1 still stands as an authoritative, fundamental treatise on the use of the electric current in geological studies, in spite of the rapid evolution of geophysics during the last seven years. A remarkable feature of this book is that, even then, it stressed the role of electricity in structural investigations and made public the first successful results obtained therewith. Stratigraphic studies have been pursued continuously by Conrad Schlumberger and his associates since 1912, the only interruption being the World War. The results attained demonstrate the wide possibilities of electrical exploration in structural work. This field of activity is, at the least, as varied and valuable as the search for ore. It is curious that until very recently it has so slightly attracted the attention of geophysicists and geologists on this continent. The purpose of this paper is to present briefly some examples of the practical application of the potential methods to geological studies. These examples are chosen from a number of problems solved in the field by our firm, in the course of its consulting practice. Certain fundamental points are briefly stated before the field operations and interpretations are described.

Jan 1, 1928

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By Severn P. Brown

Search for ore continued at a feverish pace-as can be attested to by anyone who has tried to arrange for extensive diamond drilling. The stakes are high, and so is the cost as was indicated by Selco Exploration Ltd. when they announced discovery of base metal sulfides at Uchi Lake in northwestern Ontario. It was apparently their first commercial find after 15 years of exploration at a cost of more than $10 million. For the first time in many, many years the big exploration news has come from east of the Mississippi River. In January, the New Jersey Zinc Co., in an unusually worded press release, stated that they had made a major zinc discovery of 13-50 million tons of ore averaging 5-10% Zn. New Jersey's holdings are said to embrace 500 sq mi. The ore was discovered in eastern Tennessee in the upper part of the Knox dolomite of early Ordovician age. Reportedly the mineralization is at depths of 900 to 2000 ft. Currently about 20 diamond drills are working the area for New Jersey. At least nine other major companies are prospecting the region, which now includes parts of Kentucky. Five hundred thousand acres are said to be under lease. Greatest activity is clustered around Carthage, Tenn. In Missouri, the St. Joseph Lead Co. announced plans to develop a new mine in the Brushy Creek area of the "New Lead Belt." copper and zinc concentrates will be by-products.

Jan 1, 1970

By G. F. Leaming

The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. ? Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Learning for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Learning's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Learning is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed. ?

Jan 1, 1986

Key elements of open-pit design fixing the ultimate pit limits are stripping ratio, pit slope angle, and grade cutoff. Results of exploratory and development drilling should be reduced to horizontal sections corresponding to level spacing. It is advisable to interpolate the actual drillhole values to a uniformly spaced 50-ft grid system. Vertical sections can be and are used to approximate the fixing of pit limits, but horizontal sections must be used to optimize a pit design. To develop a pit design requires the establishment of the break-even stripping ratio. This ratio is applied only at the surface of the final pit and must not be confused with the over-all ratio, which is always less; otherwise there would be no profit in the operation. The break-even stripping ratio is determined by the formula: [ ]

Jan 10, 1967

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By W. E. STOKES

COMPANIES operating airplanes have had a relatively prosperous year, permitting them gradually to re- place old types of equipment. The pre-eminence of American-made planes, engines, and accessories has been challenged, either by foreign designs or by domestic patterns that have, for one reason or another. been licensed for manufacture abroad.

Jan 1, 1938

By Carl Lemke

SOME of the principal metallurgical difficulties en-countered in the differential flotation of lead-zinc-iron sulfide ores arise from the following causes: The oxidized, or partly-oxidized, condition of one or more of the minerals ; impurities in the minerals them-selves; composition and character of the gangue miner-als; soluble salts in the ore; and unfavorable metal ratios. In many of the ores received at a custom mill there are present appreciable amounts of oxidized' or partly-oxidized minerals, although the ores may be substantially sulfides. Often the ores are not oxidized at all when received but on account of operating condi-tions at the mill it is necessary to stock them for several months before they can be milled, and considerable oxi-dation takes place while they are lying in stock. In most ores received at Midvale, when oxidation is pres-ent, the lead and iron sulfides have been more affected than the zinc sulfide, but with some ores the zinc mineral has also become partly oxidized. Some ores, such as those taken from old mine-dumps or from old stopes, may show very little total oxidation, but the greater part of the valuable minerals has been sufficiently acted upon by oxidation to make the minerals very difficult to float. Ores of this character are among the most difficult the flotation operator has to contend with, be-cause the galena, sphalerite, and pyrite are all sluggish in their behavior in the flotation cells. Only a part of the lead mineral will float in the lead circuit. The re-mainder will lag badly and tend to come up with the zinc or, if badly oxidized, will go -through all the flota-tion circuits into the tailing. The zinc mineral, if it has also been affected by oxidation, will act in a man-ner similar to the lead mineral. A hard pull will be required to float a reasonable percentage of it, and this is likely to bring up so much pyrite that it will be difficult to make a zinc concentrate of commercial grade. If it happens that the zinc mineral has not been no-ticeably affected by oxidation it will tend to float in the lead circuit because a hard pull is also required in that circuit in order to bring up the sluggish galena. When only a fraction of the sulfide minerals has become partly altered, or completely oxidized mineral is present in relatively small quantity, it is usually possible to make reasonably clean concentrates of all three sulfides, that is, lead, zinc and iron concentrates. Most of the oxi-dized and semi-oxidized minerals will go into the tailing and the losses will be proportional to the oxidation.

Jan 4, 1927