Search Documents

By J. D. McClung

INTRODUCTION The ever increasing demand for coal sues that meet exacting specifications has made necessary the installation of thousands of dollars worth of crushing equipment by the coal industry. At one time the operator at- tempted to recover as much lump as possible but today he is confronted with the necessity of crushing to facilitate the mechanical cleaning process and to meet the demand for a variety of uniform sizes. As a matter of fact, about 65 percent of the coal mined in the United States today goes through preparation plants where it is crushed and cleaned. One becomes more aware of the importance of the art of comminution when it is realized that practically all of the operations in mining are involved in comminution in one way or another. Whether the coal is mined conventionally or by continuous miners it is separated from the solid by a breaking, ripping or milling action which essentially amounts to a comminution operation. Even degradation resulting from material handling from the mine working face to the preparation plant might in a broad sense be so classified, Then of course crushing is usually necessary in the plant before the coal is ready to be marketed. THEORY Despite the various comminution operations there is a lack of satisfac- tory information concerning the fundamentals of crushing and their relation to the variable factors associated with the operation. There are certain laws and theories on mechanical reduction, such as those of Rittinger, Kick and Bond that are helpful and useful. The difficulty in developing exact mathematical relationships for specific crusher applications is due to the many variable physical characteristics found in coal. Hardness, as measured by the Hardgrove grindability index, is one parameter that has been used for years to determine the resistance of coal to comminution. While the coal properties as measured by grindability are complex, recent work has shown that a high correlation exists between the grindability of some coals and their petrographic analysis. Early research on the hardness of petrographic entities from an Illinois coal2 demonstrated that durain was the hardest constituent followed by clarain, vitrain and very soft fusain. Other research demonstrated that, for different size fractions of the same coal, a wide variation in hardness commonly exists. For example, the fines in about half of 39 coals studied were softer than their corresponding coarse sues while most of the remaining coals were uniformly hard in all sizes. A few coals contained fines which were harder than their coarser constituents. These variations in hardness give insight into the heterogeneous nature of coal.

Jan 1, 1968

By Lewis T. Wright

It is commonly believed by metallurgists that in copper-smelting, the copper in the slags, which is irreducible by continued " settling," is retained in the form of " prills " of matte. I have frequently held well-settled slag in a molten condition for a long period without being able thereby to reduce the copper-content. The slag acted as though it contained a minimum of dissolved or combined copper that could not be settled out by gravity. I have used reagents, but without satisfying myself in what form this copper existed. The same slags, by fine grinding and elutriation, could not be separated into portions containing more or less copper than the average content. By treating copper-slags in an electric furnace a button of metallic iron and copper was produced, but the high temperature and the strong reducing-action of the furnace mere influences that suggest an explanation of a result not obtainable with ordinary smelting-temperatures. If all the copper in the slag were in the form of copper-matte, and not existing as a dissolved compound with some of the elements of the slag, then the other metals in the matte, such as gold and silver, should occur in the slag in the same ratio to the copper as to the copper in the accompanying matte. This reasoning led me to study the ratio of metals in the products of smelting, and, apart from the issues discussed in this paper, the research has proved both interesting and illuminative. On the assumption of a similar ratio of metals in matte and slag, if the percentage of copper in the slag accompanying a matte containing 50 oz. of silver and 1 oz. of gold per ton of copper was 0.3 per cent., or 96 oz. per toll of slag, there should be found 0.15 oz. of silver and 0.003 oz. of gold per ton of slag; but, in my experience, there is less silver and much

Jan 1, 1910

By Edward Keller

(New York meeting, February, 1912.) IN a paper, entitled A Uniform Method for the Assay of Copper Material for Gold and Silver,1 A. R. Ledoux invited the assayers of this country to contribute to a symposium, in which the results of their assays of given samples of copper-matte and metallic copper would be made comparable. This symposium 2 appeared about one year thereafter; and through it and its discussion, first became generally known the fact that the ,gold-yield by the all-fire method of assaying is usually higher than by the so-called combination (wet and dry) method, in which nitric acid is employed as a solvent for the copper. In the publication alluded to, the supposed cause of gold-losses in the latter method was declared to be the solvent action of copper nitrate, or of the reduction-products of the nitric acid, upon the gold. Up to a very recent date, gold has been held to be insoluble in pure nitric acid. (The solvent action of any chlorine present in the nitric acid must here properly be disregarded as belonging in the realm of carelessness. Among later allusions to this topic, W. R. Tan Liew 3 ascribes the solution of the gold in the combination-assay entirely to the action of nitrous acid at the high reaction-temperature of copper and nitric acid ; F. B. Flinn 4 a believes the low result in gold to be due exclusively to mechanical losses-finely-divided gold penetrating through the filter-paper-but presents no experimental data confirmative of this belief; and 0. Pufahl 5 attributes the solubility of the gold in some coppers to the presence of selenium-a view which appears to be shared by many as- 1 Trans., xxiv., 575 (1894). 2 Trans., xxv., 250 (1895). 3 Engineering and Mining Journal, vol. lxix., No. 16, p. 469 (Apr. 21, 1900). 4 Engineering and Mining Journal, vol. lxxxvii., No.11, p. 569 (Mar. 13, 1909). 5 Lunge, Chemische Technische Untersuchungs Methoden, vol. ii., p. 229 (1900).

Jul 1, 1912

By H. H. Dievendorff, F. W. Hertel

The method of drilling deep wells into the earth for the recovery of oil and gas is beset with many hazards. This is especially true in the Ventura Avenue field, which has the distinction of being the hardest field in California in which to complete a deep well. The hard, shifting and squeezing formations must be penetrated to great depths in the face of tremendous gas pressures. This field presents problems that keep the operators abreast with all of the latest developments in oil-field tools and machinery and in oil-well drilling practices. Equipment must be strong, and adapted to deep-well drilling and the handling of long heavy strings of casing. High-pressure sands require the utrnost care and attention of the operators and no chances can be taken, since a serious blowout may cause the loss of a well that has cost months of labor and expense. Equipment must meet these requirements or be discarded. Although the deepest wells in the world are not in this field, nor hav:. the longest strings of casing been set, nevertheless, the consistency with which deep wells are drilled and long strings of casing are set places the Ventura Avenue field foremost, in this respect, among the oil fields of the world. The V'entura Avenue field dors claim the deepest commercial oil-producing well in the world, in the Shell Co. of California's "Edison" No. 18. This well was drilled 7015 ft. and came in flowing 3280 bhl. of oil per day. This field also claims the deepest average depth of producing wells in that its Ill producing wells average 5676 ft. in depth. Of these 111 producing wells, 50 arc 6000 ft. or deeper, and 16 are 6500 ft. or deeper. Also, of the 111 producing wells 100 arc flowing, and 11 arc pumping wells. This paper is intended to set forth the methods used in the drilling of deep wells with rotary tools and the handling of long heavy strings of casing in the Ventura Avenue field.

Jan 1, 1928

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By W. H. Adams

During the years when Americans were most active in investigations of the many substances containing nitrogen or ammonia, viz.: 1869 to 1875, my connection with certain chemical industries led me to experiments in the direction of the recovery of wastes from coal-gases. I take from my notes such memoranda as I think will be of interest, in the hope that some benefit may be derived therefrom by engineers at present attempting to utilize the waste products from coke-oven and blast-furnace gases. An examination of the conditions governing the manufacture of gas along the Atlantic seaboard, and an intimate knowledge of the mine-products used by the different large works, naturally led me at first to consider the well-known foreign methods of concentrating the available soluble salts in a modicum of water. The result was sufficiently promising to warrant a full line of experiments. At that time, no attention seemed to have been paid to the values of " gas-liquors." Nearly every gas-works in the United States wasted its wash-water in the sewers. The nitrogen in bituminous coals varies in quantity from 0.75 to 1.50 per cent. of the total weight. In the process of distillation in

Jan 1, 1887

By D. S. Fuerstenau, S. Chander

The results of a preliminary investigation undertaken to explore the possibility of treating potential in sulfide mineral flotation systems as an external variable are reported in this note. Two different methods were used to assess floatability. One involved measurement of contact angles at a mineral electrode in reagent solutions, and the other involved direct measurement of flotation recoveries in a Hallimond tube flotation cell that had been modified such that mineral particles were in electrical contact with a gold electrode. Fairly good correlation between the contact angles and flotation recoveries has been obtained.

Jan 1, 1976

By C. S. Matthews, M. J. F. Rosenbaum

The purpose of thir work wax to lcarn it~lzut infori~lation could he obtained from various typs of pilot water floods and to attempt to find the optunum pilot patter11, for a revervoir which had previously been depleted by a solution gas drive. The study was made in the laboratory with mathemetical methods a dynamic analog and a potentiotnetric analog. Results werp tested against the field llistorics of a nrrnlber of pilot water floods. At a reasonable valrre of currzulative injection, the total production rate for the one-injector five-spot should reach about 6.5 per cent of injection rate, and for a four-injector five-spot, about 9 per cent. Accurate estimates of ultimate recovery cannot be made on the basis of such snzall prorluction rates. However, with a pilot composed of nine ir1jector.s and 16 producers the production rate is approximately 50 pcr cent of injection rate at a reasonable value of camulative injection. Sonle inforn~ation for extended performance predictions might he obtained from such a large pilot. These conclusions were drawn on the basis of results obtained for unit mobility ratio, and a sturly using tlre potentiometric analog was made of the effect of other mobility ratios to determine the range of applicability of these predictions. For the four-injector, five-spot pilot with the ratio of production to injection rate (before water breakthrough) is about twice that for with it is about two-thirds; and with M0= 10, it is about one-third For high mobility ratios, it was found that the production rate increased considerably as water-cut increased. These result can be used to modify, qualitatively, the inter.pretntions based on curves for the unit rnobilit\. ratio CaSeS. It was found that the maximum ratio of production rate to injection rate obseriled in field pilot floods was of rhe scime order as that prerdicted by these methods. The time required to reach thisr maximum did not generally agree with the time predicted for a homogeti~orir reservoir. The differcrlce between predicted and observed time of response gives an indication of the permeability profile and of the condition of the producin,g wells. Pilot water floods of the pattern type are generally carried out in reservoirs which have been depleted by solution gas drive and are at low pressure. Under these conditions, oil and water can be considered incompressible. It is assumed that, as the water is injected, an oil bank forms ahead of it and that there is a distinct interface between the water zone (or bank) and the oil zone (or bank) and between the oil zone and the region ahead of the oil zone. It is further assumed that only gas is mobile in the unflooded (gas) region, only oil is mobile in the oil bank and only water is mobile in the water bank. The saturations and the mobilities associated with each zone are assumed uniform. We idealize our reservoir to be homogeneous, horizontal and of constant thickness. Effects of gravity within the producing layer are assumed negligible. If the actual time-dcpendent flow problem is approximated by a acries of steady-state problems. the potential and stream function in the oil bank and water hank satisfy Laplace&apos;s equation in two dimensions. We can therefore use a poteiitiometric analog of this system. Potentiometric models have yielded uscful results in this laboratory&apos; and clsewhere in the study of a variety of secondary recovery problems. For the case where M = I, we generally prefer to use theoretical mcthods as well as a simpler dynamic analog. Except where otherwise noted, the ratio, side of five-spot/wellbore radius. is taken to be 3,600. a figure which corrcsponds to a normal-size wellbore in a 10-acre well spacing. THEORETICAL EVALUATION OF VARIOUS PILOT PATTERNS, Mw0 = 1 <&apos;he theoretical models which we used to examine the performance of various pilots are shown in Fig. 1. Image theory was used to determine the ratio of production rate to injection rate as a function of the volumc of the flood. The ratio of production rate to injection rate was chosen because this is an easily measurable quantity which is characteristic of a pilot

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By AIME AIME

MONDAY, Feb. 21, evokes memories of the Silver Corridor at the Waldorf to be recalled and reflected upon for time to come when thoughts drift to the Annual Meeting of 1944. Crowded though it was, on occasion there lurked in the mind&apos;s eye a vision of what might have been had the 2886 persons who put in an appearance at one time or another milled around in the lobby of 29 West 39th Street. Some confusion resulted from difficulty in locating meeting rooms, but for the most part everyone found what he wanted. The usual bulletin board of members registered was missing this year and rumor has it that tile Waldorf didn&apos;t approve. Registration broke all previous records with many a busy engineer realizing that the program had something to offer that would be of use in his particular job. It might be noted here that "Arpad" co-operated nicely, previewing spring days on Monday, Wednesday, and Thursday; Tuesday was a bit damp.

Jan 1, 1944

Western Mining Corp. has announced plans to expand its mining operations at Kambalda, and to build a nickel refinery at Kwinana, near Perth, Western Australia. The refinery will use the ammonia-leach hydrogen reduction processes of Sherritt Gordon Mines Ltd., and it is expected that by 1970, when the expansion is scheduled for completion, Western will be the world&apos;s fourth largest nickel producer. Although estimates have not been finalized, the total cost is expected to be about $55 million. The mine and mill facilities at Kambalda, which began production in June 1967, are now producing at the rate of 11 million lb of contained nickel per year. The company estimates the sulfide ore reserves at Kambalda and St. Ives at 10.4 million tons averaging an usually high grade of 3.8% nickel, or about 790 million lb of contained nickel. In addition, silicate and oxidized ores have been located in both areas.

Jan 3, 1968

By R. Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.&apos; Characteristics of the system have been sketched by Boden.2 The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl3 is ruled out by their instability and other disadvantages.&apos; Despite its enormous superiority in specific impulse, the ion rocket is inherently low-powered, capable of very small acceleration. Application of ion propulsion will be limited to large rockets and spaceships on missions requiring powered flight for weeks or months and employing a separate chemical propulsion system for escape from the earth&apos;s atmosphere where power requirements are large but of brief duration. For example, Kraemer and Larson3 considered the case of an unmanned 25,000-lb pay-load placed in a 300-mile orbit by chemical rockets, proceeding thence by ion propulsion to the vicinity of Mars, where it would go into orbit once again. Calculations provide for 8500 lb of cesium for such a voyage. The question of whether such quantities of cesium will be readily available to the space program does not appear to have been considered by geologists and mining engineers. Present Production and Uses Literature on industrial applications of cesium is scanty. The metal is used in scintillation counters, photocells, infra-red detection devices, and as a "getter" in low-voltage vacuum tubes. Production is sporadic and total figures are not published, but the annual consumption is measured in pounds rather than in tons. The few pollucite deposits known, small as they are, can easily supply the present limited demand for gram or pound lots of cesium. Until recently the price of cesium was $2 to $4 per gram, but according to Chemical Engineering, cesium salts are now available at $13 to $27.50 per lb. Geochemical Distribution As a large alkali ion, the cesium ion accompanies potassium in geological processes and tends to be concentrated in the latest crystallizing fractions of potassium minerals in much the same manner as rubidium. Most of the cesium in igneous rocks, therefore, is in the micas and potash feldspars of granites, and especially in granitic pegmatites. The cesium content rises markedly in the micas of the late by-drothermal replacement stage in complex pegmatite~.&apos; Typically, cesium is only 0.5 to 0.01 times as abundant as rubidium in potassium minerals. Rb&apos;, with a radius of 1.47 A, is close enough in size to K&apos; (1.33 A) so that rubidium forms no minerals of its own. Cs+ is so large (1.67 A) that only small concentrations can be taken up in potassium minerals; when cesium is present in solution in larger concentration it forms the mineral pollucite, Cs3-Na2A17Si17O48.3H2O, which is known only in pegmatites. In the weathering of igneous rocks, cesium is dissolved, carried to the ocean, and apparently in-

Jan 1, 1961

By Maurice Rey, Victor Formanek, Paul Chataignon

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then .black by sodium sulphide, in their presence the mineral remains very light in color. A similar- effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium- sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact ,with the mineral simultaneously with the formation of lead sulphide.

Jan 1, 1950

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By Norman D. Fitzgerald

The purpose of this paper is to analyze the behavior of oil securities during the six-year period January 1932 through December 1937. This period was selected because of its varied character. It includes the depths of the depression, the broad and spasmodic recovery, and the recession collapse. The first part of the analysis is devoted to the correlation of a number of economic factors with an index of 13 oil stocks. The second part is a comparison of the different,ial behavior of 6 oil stocks. The relationships developed here are only a few of many that might be considered in a complete analysis. The stock market is regarded as a barometer of business confidence and as such exerts an important influence upon corporate policies, particularly upon industrial expansion. The complex and continuously changing nature of its price structure, the ebb and flow of influences and the effects of impacts require dynamic rather than static analysis. When treated in this way, many of the important fluctuations in market prices and changes in the relationships between securities appear quite logical. The market for oil securities has varied widely in recent years. The Standard Statistics index of 13 oil stocks made a bull market peak of 166.7 in September 1929. The collapse of the boom and the ensuing bear market finally carried the index down to a low of 36.4 in June 1932. From this point oil stocks made an irregular recovery; they reached a top at 139.7 in March 1937, and after maintaining this approximate level through August, declined precipitously to 93.3 in December 1937. The prices of these 13 oil stocks have gone up and down under the influence of numberless variables. These variables are of two kinds, those external to the industry, and those that are solely due to its internal condition. The external factors are political, social, and economic, both domestic and foreign. These are the influences that induce the ebb and flow of all prices in general and security prices in particular. Among the internal factors are the regulation of industry, the development of new reserves and processes, and the disequilibrium due to lack of balance between supply and demand. Some of the simpler relationships are examined in this paper.

Jan 1, 1938