Search Documents

By O. F. Walker, W. C. Hahn, V. A. Johnson, J. D. Wood

The diffusion coefficients of zinc in single-crystal zinc and carbon in single-crystal and poly crystalline nickel were measured by means of radioactive tracer techniques both with and without the application of ultrasonic vibrations under conditions such that the temperature of the sample was closely controlled. The results of this investigation indicate no enhancement of diffusion in any of the samples. It is suggested that previously reported enhancement may have been due either solely to temperature increases caused by ultrasonic vibrations or in combination with changes in the boundary conditions. A number of observations have been reported in the literature in which it has been implied or inferred that the application of ultrasonics enhances diffusion (see, for example, Refs. 1-5). The present study was undertaken in an attempt to observe this effect under carefully controlled conditions, particularly with regard to measurement and control of the temperature of the sample. Two different types of systems were studied; these were the self-diffusion of zinc and the diffusion of carbon in nickel. EXPERIMENTAL For diffusion with ultrasonic energy applied, the samples were included as part of a resonant ultrasonic system operating at 58.5 kcps. The ultrasonic generators used were rated at 100 and 250 w and could be tuned over a frequency from 10 to 100 kc. A PZT (lead titanate/lead zirconate) ceramic transducer provided the driving vibration. This system requires no metallurgical joining of the specimen to the acoustical transmission line since the ultrasonic driver and the follow-up section clamp the specimen in position by means of a constant pressure of 50 lb developed by an air cylinder. The ultrasonic driver and follow-up section, both made of titanium, were 4 in. in length from clamping point to the end in contact with the specimen. Using the relationship given by Mason,6 A = V/f, the resonant wavelength, A, in titanium is calculated to be 3.3 in. at a frequency, f, of 58.5 kc, taking the velocity of sound in titanium, V, as 1.95 X 105 in. per sec. The 4-in. driver and follow-up section, therefore, are each 4.0/3.3 =1.21 times the resonant wavelength. Clamping pressure must be applied at stress nodes of the transmission line in order to preserve resonance. Therefore, a specimen length of 0.58 times the wavelength in the specimen was required to place the clamping pressure application points at stress nodes exactly three wavelengths apart. A stress antinode was contained in the center 3 in. of the specimen. A small PZT ceramic disc attached to the follow-up section provided an output voltage proportional to the intensity of the standing wave. This output voltage was monitored on an oscilloscope and the ultrasonic system was tuned to resonance by varying the frequency until the output signal was a maximum amplitude. The amplitude of the output signal was maintained constant throughout the diffusion anneal. A split cylindrical stainless-steel chamber, which was purged with argon prior to and during the runs, was placed around the specimen. The chamber in turn was surrounded by a movable furnace whose temperature could be controlled to 7C. Heat exchangers were used to cool the driver, follow-up section, and ultrasonic transducer. Great care was taken to obtain the true specimen temperature in all cases. Several different methods were tried; the most successful was that in which the thermocouple was held in contact with the midlength of the specimen by means of an asbestos insulating pad and wire straps. In the case of zinc, single-crystal specimens of 99.999 pct purity were used. The samples were 0.25 by 0.25 in. square and of the proper length for resonance, that is 1.1 in. long with the c axis parallel to the long dimension of the specimen for the case of diffusion perpendicular to the c axis and ultrasonic motion parallel to the c axis, and 1.9 in. long with the c axis perpendicular to the long dimension of the specimen for the case of diffusion parallel to the c axis and ultrasonic motion perpendicular to the c axis. In each case, one of the rectangular faces was electroplated with a thin film of zinc containing Zn The constant pressure used to clamp the specimen in place in the ultrasonic system caused some deformation in some of the samples. For these samples the deformation was concentrated in either end of the specimen; thus, for all samples (both zinc and nickel) the center in. was cut from the specimen after the diffusion anneal to be used for sectioning and counting. The nickel single-crystal samples, of 99.999 pct purity, were used in the form of rods 0.25 by 0.187 by 2.07 in. long with the (100) direction parallel to the rod axis. The polycrystalline nickel samples of 99.97 pct purity had an average grain diameter of 0.007 in. and were used in the form of rods 0.25 by 0.125 by 1.87 in. long. The direction of ultrasonic motion was parallel to (100) direction (bar axis) for the single-cqstal samples and parallel to the bar axis for the polycrystalline specimens. A thin film of c14 suspended in methanol was applied to the diffusing face of the specimen. Two specimens were butted together lengthwise for each diffusion anneal to minimize oxidation. After diffusion, a precision lapping device similar to the one described by Goldstein7 and a radiation detector were used to obtain a plot of specific activity vs penetration distance for each specimen. (A scintil-

Jan 1, 1969

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By Ralph M. Roosevelt

IN AS MUCH as our Institute, by tradition, never adopts any official view of matters upon which difference of opinion exists, it may be taken for granted that the duty of its Production Control Committee does' not embrace the formulation of any general policy on that much-discussed subject. During the first years of its existence the Committee confined its activities to making arrangements for an annual general session at which the broader aspects of the general problem were discussed by men both within and outside the mineral industry. These general sessions, although interesting, did not indicate any definite path of progress, so during the last year the Committee has held a number of luncheon meetings at which the members might discuss in detail problems existing in the specific industries with which they are most closely acquainted, in the hope that discussions dealing with conditions rather than theories might result in the bringing to light of some general truths. Most of these truths have been fairly obvious from the beginning but they are of such basic importance that a periodic restatement of them seems worth while,

Jan 1, 1932

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. 'Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942

By T. V. Philip, Paul A. Beck

IN a previous note1 it was pointed out that the available information suggests a distinct correlation between the occurrence of the CsCl-type ordered structures formed in equi-atomic binary alloys of transition elements and the location of the components in the periodic table. A definite increase in the bond strength between unlike atoms, as compared with that between like atoms, is indicated when, in binary alloys of iron group elements, the other component is changed from chromium to vanadium or tantalum, to titanium. Laves and Wallbaum,2 eported a CsCl-type ordered structure for the stable intermediate phase at the equi-atomic composition in the Ti-Fe system (and also in the Ti-Ru and Ti-Os systems). On the other hand, Tagaya, Nenno, and Nishiyama8 found no ordering of this kind in the body-centered-cubic solid solutions in the Cr-Fe system. It was concluded' that the occurrence of a CsC1-type ordered phase of intermediate stability may be expected in the V-Fe system. Preliminary results were described: suggesting that at least some degree of order does exist in the equi-atomic alloy VFe, annealed at 1200° C and quenched in cold water. Using CrK radiation, at least one weak superlattice line was found in the X-ray diffraction pattern which could be indexed as (100). and which disappeared, as expected, when FeK radiation was used. It was found more recently that the impurity phase (presumably VN), previously giving rise to additional X-ray diffraction lines and thus preventing definite indentification of the (111) superlattice line,' can be eliminated by preparing the alloy by arc melting in a helium atmosphere. The alloy specimen melted in this manner had clean surfaces and showed very littte, if any, nitride phase in the microstructure after annealing in vacuum at 1250°C and quenching. The relative intensity of the (100). superlattice line with CrK radiation was greatly increased and, in addition, a fairly strong (Ill) , superlattice line and even a detectable (210) , super- lattice line was obtained, when the powder produced by filing from the 1250°C annealed and quenched specimen was reannealed in vacuum at 625°C for 1 hr. By using a cellulose acetate film as a filter in front of the photographic film in order to absorb the soft radiation resulting from air fluorescence, the background intensity could be reduced considerably in relation to the intensity of the diffraction lines. All three superlattice lines, (100),, (111)., and (210)a, disappeared, as expected, when a radiation other than CrK, was used.1 For the powder reannealed at 625ºC, the strongest lines of the s pattern also appeared weakly, indicating that during an: nealing at 625°C a small amount of transformation took place from the body-centered-cubic to the u phase. However, since all superlattice lines to be expected in the 0 angle range used were actually very clearly present, it was evident that the high temperature body-centered-cubic phase had transformed into a CsCl-type ordered structure before much s phase could form. Reannealing filings for 1 hr at 700°C resulted in complete transformation into the u phase. After 1 hr at 650°C the transformation into IT was not quite complete, the strongest body-centered-cubic diffraction lines were still present, although fairly weak, and only the (100), super-lattice line was detectable (extremely weak). These findings not only confirm the previous conclusionsL as to the existence of a CsCl-type ordered structure in the Fe-V system, but they also indicate that this metastable ordered structure forms at about 600°C preceding the formation of the stable s phase, while at 1250°C the disordered body-centered-cubic phase is stable. The faint (loo) , super-lattice line previously observed in specimens quenched from 1200°C was probably due to the fact that the quenching of the powder in an evacuated fuse:! quartz capsule was not fast enough to prevent completely the ordering reaction on cooling. The present results conform with the suggestion that the A-B bond, in relation to the A-A and B-B bonds, increases in strength from CrFe to VFe to TiFc. It is, therefore, of interest to compare the measured values of the average atomic diameter for these three alloys with the corresponding average atomic diameters calculated from the atomic radii of the elements concerned. ASSUming A-B contacts

Jan 1, 1958

By Pedro L. Lizaur

INTRODUCTION The degree of success of an association between parties in establishing a new venture ultimately depends on three factors: a. the venture's underlying economic strength, which is based on the complementarity of the comparative advantages brought by each party to the negotiating table; b. the ability to reach an agreement which satisfies each party's objectives and constraints; and, c. the capacity to design and implement a funding structure which is consistent with the project economics. A thorough assessment of the venture's profitability and associated risks under alternative technical and economic scenarios is the basis for a sound "go" or "no go" decision. In-depth evaluation of the risks and rewards to each of the parties involved under alternative legal and financial structure must be the foundation for a long lasting "how to go" decision. The allocation of risks and rewards should be consistent with the objectives and constraints of all parties and the sharing mechanisms, established in the contract, should be flexible to assure the long-term stability of the agreement. Rapidly changing economic conditions during the last decade have had a dramatic impact on the envisaged allocation of risks and rewards between host countries and private investors. The effects of these changes, and the fact that the relative strengths of the parties involved may shift during the life of a project (e.g. before and after major capital investments have been made), have forced the renegotiation of a multitude of contracts. Therefore, the present and future stability of an economic agreement would depend not only on the originally designed provisions, but also on provisions which allow for the automatic adjustment of rewards to project sponsors under a variety of future economic situations. A pre-condition for the allocation and quantification of risks and rewards is the definition of standards of measurement used by each of the parties. This is critical in international negotiations when one of the parties represents the national interests of a country. The understanding and use of different standards for the measurement of rewards for risk taken between a government and private enterprise facilitate the negotiation of a satisfactory agreement. This is possible because certain trade-offs between the negotiating parties may have different relative values. STANDARDS OF MEASUREMENT OF REWARDS FOR RISK TAKEN The negotiating process takes a step forward when the parties are able to focus on their interests, explore different alternative solutions and then base results on a set of objective standards. Unfortunately, the parties frequently put more effort into "staking out" and defending positions, than into understanding their intrinsic interests. Moreover, when one party, such as a governemnt owned corporation, represents a country's national interests, the negotiation process increases in complexity. Private firms focus on commercial profitability, using discounted cash flow techniques such as NPV, IRR, or ROE. In contrast, the government is also concerned with the project's impact on the local socio-economic environment. Without entering into a discussion of alternative economic development theories and approaches, there exist several possible measures that could be pragmatically utilized by each party in evaluating the socio-economic impact of a project. The more complete measure is the National Profitability (NP). The NP is a discounted cash flow procedure similar in structure to IRR or NPV but in which the project's financial cash inflows and outflows and discount rates are adjusted to take into consideration the local conditions. The NP is calculated on an unlevered basis and all taxes and duties are removed from the project

Jan 1, 1985

By Jin Zigang

In China there are more than 30 coal fields menaced by karst-confined water. In the north and east of China there are many collieries which mine coal seams of the Carboniferous and Permian Systems, which are above the Ordovician limestone (general thickness is 500-600 meters). Ordovician limestone is full of karst fissures, contains a lot of water under high pressure (15-65 kg/cm2) near the commercial coal seams (20-80 meters), the water easily infiltrates the thin lime- stone at the point of the structure crevice, so water-irruptions from the floor are the main source of water-related disasters in these coal fields. According to the statistics there were more than 300 accidents of all kinds of water-irruptions from the floor in these fields since the beginning of their development. It is of great significance in developing coal production in the eastern part of China to solve the problem of safe mining of the seams menaced by the karst-confined water of the Ordovician limestone. The research on this subject consists of three parts: (1) investigating the geological structure and hydrogeological conditions of each mine of the mining area; (2) researching the mechanism of water-irruptions from the floor and proposing reliable methods to predict and monitor; (3) improving the mining system and proposing a mining plan with safety precautions against water-caused accidents. The chief task is to research the mechanisms involved and to discover the causes and conditions of the phenomenon. The authors have obtained some findings on this subject in the last five years, making use of the comprehensive observation and research system, which will be discussed under three headings.

Jan 1, 1984

By Keith T. Griffiths

INTRODUCTION The Empress Nickel Mine is situated forty-eight kilometres west of Kadoma in the Zhombe Communal Land of Zimbabwe. The mine came into operation in late 1968 based on a proved and probable ore reserve of twenty million tonnes. The initial production rate was 55 000 tonnes per month from underground. This was boosted to 85 000 tonnes per month in mid 1970 when the opencast operation came into production. The mining method at Empress is sub-level open stoping with main haulages mined at ninety metre intervals and sub-levels at eighteen metres. The extremely wide ore body of up to one hundred metres in width has necessitated leaving extremely large rib pillars and sill pillars in position to maintain mine stability and to act as regional support of the hanging wall. In early 1976 the opencast operation had reached its final economic depth and it was then necessary to increase underground production to 85 000 tonnes per month. Since a large portion of the ore reserve remained in both rib and sill pillars, it was necessary to embark on a positive pillar recovery programme. For this reason it was decided to introduce a sandfilling programme for the mined-out stopes and a modified system of sub-level open stoping with post filling of the lower stopes. ORE BODY GEOLOGY AND GEOMETRY The Empress orebody outcrop has a strike length of nine hundred and fifty metres on a north west - south east axis. It is a steeply dipping (65' - 75') tabular orebody of gabbroic rock which has been extensively altered. The north west - south east strike length of nine hundred and fifty metres on surface reduces to some two hundred

Jan 1, 1983

Although the Suggestions to Institute Authors, as revised and amplified over the years to meet changing conditions and experience, have had as their primary objective the guidance of the author who is preparing a paper for record in the TRANSACTIONS, there are in this current version many excellent suggestions for the preparation of any material for publication by the Institute In this connection it should be emphasized that in a sense, and to a degree determined by the editors, the Institute has in its journals "a place for everything," especially a place for the article of practical nature that is of immediate but not necessarily permanent interest Such articles may be referred by the Institute Technical Publications Committee to the editors or submitted directly to them , [Papers (TECHNICAL PUBLICATIONS and TECHNICAL NOTES) authorized for the TRANSACTIONS are, with the discussion, gathered together at the end of the calendar year and with a table of contents and index, bound, according to Branch classification, as volumes of the TRANSACTIONS

Jan 1, 1952

By Harry M. Callaway

IN times of a falling metal market the mine operator attempts to remain in competition by lowering his overall cost and raising the grade of ore he processes. But these adjustments can be made only within narrow limits imposed by inherent characteristics of the operation. Is there some additional method whereby the break-even point can be lowered? One approach, perhaps the only one, to lower a break-even point is careful cost analysis considering both fixed and variable costs in relation to mining rate. The following is an analysis of cost distribution and its significance in determining the most economic combination of the factors of ore grade and tonnage output applicable to a given mining operation.

Jan 4, 1958

By P. K. Lucke

ONE of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebOdies occurred. This table land lies at altitudes ranging from 4000 to. 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. FIG. 1. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulphides above, and I will endeavor to explain the causes of the phenomena in certain specific instances.

Jan 6, 1918

By Tom Bilson

TO recover the remaining ore tonnages along the south side of the Inspiration orebody, the company began open-pit operations in early 1948 in addition to underground mining. Due to the differences in elevation between the orebody and the existing ore handling and treating plants, the truck haulage operation is up hill. Road grades were established at 7 pct maximum.

Jan 8, 1951

By A. F. Peterson, A. R. Eshbach

Much has been written to explain decreasing profits in American industry. Foreign competition, the attitude of government, rising tax burdens and increased labor costs have been blamed in turn. Whatever the cause, management in the mining industry, as elsewhere, is increasingly aware of diminishing profit margins. A mine operator is usually unable to do much about the causes of decreased profits, even if he knows what they are, but he can check the trend in part by cutting the cost of operation. To do this, he must know what his costs are, which of them are most significant and then go about reducing them in a systematic and logical manner.

Jan 10, 1962

PRACTICAL PROBLEMS AND BASIC PRINCIPLES ranging from ore testing to cost estimation get a working over from top men in the minerals beneficiation field. The Minerals Beneficiation Division developed this symposium for presentation at the 1953 Los Angeles General Meeting to assist the many people who think that having a new plant necessitates a lot of trouble and dismay. The papers and free discussion from the floor give ways and means of approaching a new plant that will relieve the strain on the organization, if adequate attention is put on the program before work begins - that is if thought is given to the program itself, before tackling the actual mill design.

Jan 9, 1953

By W. F. Shinners

Ozark Ore Co.'s Iron Mountain mine utilizes optimum mechanization to provide ever increasing output from underground as production declines from open pit. Trackless equipment gave flexibility to meet varied mining conditions-required minimum of pre-production development.

Jan 4, 1953

By C. W. Schulties, W. J. Mallio, L. J. Petrovic, J. A. L. Campbell

Roof control comprises about 35% of direct and indirect underground mining costs. In addition, difficulties in estimating roof control costs for new areas lead to the greatest uncertainties when negotiating coal contracts. And obviously, coal cannot be mined if the roof can't be held. Accordingly, there are strong incentives to attack this problem on as many fronts as possible. One successful geological modeling technique for predicting future roof conditions was recently applied at Peabody Coal's Simco mine No. 5, located in Coshocton, Ohio. Benefits derived from it included: - A better identification of areas where poor safety conditions may be encountered. - Improved roof control cost estimates for contract negotiations. - Estimates of time-duration while mining in bad roof areas. - Labor and materials cost predictions in an existing mine. - Productivity increases through prior knowledge of areas to avoid.

Jan 10, 1975

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

Based on an analysis of green pellet size distributions and kinetic data on ball growth with taconite concentrates, a ballability index has been developed to quantify ball growth behavior as a function of moisture and bentonite additions. The applicability of the ballability index to such other particulate materials as pulverized limestone and ground magnesite is shown.

Jan 1, 1973

By Jan M. Mutmansky

Main purpose of the research described is to apply the method of computer simulation to the process of tunneling by rapid excavation methods. Primary attention was focused on the materials handling subsystem because of its potential for improvement from a systems standpoint. A description is given of the computer model and a summary of some applications of the model for improving the rapid excavation process is included.

Jan 1, 1975

PHILIP L. GILL, New York, N. Y. (written discussion*).There is one feature of the fire-refining of electrolytic copper which I believe should be mentioned when the relation of oxygen content to the "pitch" or "set" of refined copper is under discussion; that is, the segregation of impurities. Variation of "pitch" or "set" is frequently noted in castings of different shapes, cast at the same time from the same furnace, though the oxygen content remains identical. For instance, it is possible to cast two wire-bars in the same shaped molds from the same ladleful of copper, the one 2 in. thick showing a good level set, the other, 4 in. thick, being overpoled. Also, when two bars are cast of the same weight and at the same time from the same furnace, one bar in a copper mold at the proper temperature, the other in a mold that has been allowed to get overheated, the bar in the hot mold will show

Jan 8, 1918